Search Documents

By Deon van Tonder, Bert Van Hege

Comparison of various technologies for uranium recovery from sulphuric acid leach solutions shows that Resin-in-Pulp (RIP) and/or Solvent extraction (SX) based processing routes are usually cost effective (11). A combined RIP-SX recovery-purification route and a CCD-SX recovery-purification route were investigated and optimised. The design basis used for the investigation was a production rate of 200 kg/h U3O8 over a solution concentration range of 40 to 1500 mg/L U3O8. The OPEX for the RIP-SX processing route was found to be sensitive to the variation in uranium concentration in the leach liquor. One of the main drivers for this trend is the leach acid concentration. Conversely, the CAPEX of the CCD-SX processing route was sensitive to the uranium concentration in the leach liquor. The leach acid concentration only affected the OPEX of the CCD-SX processing route modestly, as the bulk of the acid is recovered in a pre-leach circuit. Contrary to expectation, the effect of extractant loss assumptions on the overall processing route economics was found to be modest to insignificant. It should be noted that the CCD-SX processing route OPEX was more sensitive to extractant loss assumptions than the RIP-SX processing route OPEX. Economic optimum wash ratios were determined for the CCD-SX processing route and increased with leach concentration ? the increase in wash ratio was less than proportional. A 5-stage CCD configuration was found optimal over the concentration range investigated.

Jan 1, 2007

By X. B. Zhao, J. G. Cai

The purpose of this paper is to incorporate the dynamic BB model of rock fracture normal behaviour into Universal Distinct Element Code (UDEC), and to conduct UDEC modelling to predict stress wave propagation across rock fractures. With the incorporation of new dynamic model of fractures, the UDEC is improved in the capability of modelling wave propagation across fractures. In this study, the case of normally incident P-wave transmission across a fracture is modelled, and the effect of dynamic normal behaviour of fracture is concentrated on. Wave transmission coefficient for wave transmission across the fracture with the dynamic BB model is obtained for various combinations of fracture dynamic parameters, as well as different wave amplitudes and frequencies.

Jan 1, 2003

By C. Bester, G. M. Rohde

A major challenge in the mining sector is the responsible management and efficient storage of mine residue. Over recent years numerous tailings dams have experienced unintended spills and failures, with severe consequences for the mining industry, the environment, local communities, and the regional economy. The fourth industrial revolution (4IR) is impacting society due to increased interconnectivity, processing speed, and automated technologies. This paper explores whether 4IR technologies have the potential to mitigate risks associated with tailings dams. Experts in the field of tailings dam operational management were surveyed to determine their view on the risks associated with tailings dams and the potential of 4IR technologies to mitigate these risks. The survey found that a majority of experts believe that certain 4IR technologies have the potential to reduce the risks associated with tailings dam failures.

May 27, 2025

By I. E. Teymenson, L. A. Bakhvalov

Irrational usage of mineral commodities leads to depletion of natural resources and various ecological violations in natural environment. Fulfilment of a number of measures and strategic decisions by given problems requires a correct forecast of trends of social-economic systems. For solving the task of long-term forecasting special procedures, considering Kondratyev’s big cycles of world conjuncture, have been embedded into algorithms of unknown parameters identification and recovering of factors of different countries mineral resources production and consumption models. In the paper the classification of long cycles types, existing forecasting algorithms on the basis of Kondratyev’s ‘long waves’ or ‘K-waves’ and the modified algorithm, developed by us, which allows to reduce time and financial expenses and to improve the forecast quality, are presented. Furthermore, the article includes several forecasts of mining branch corrected models factors, received by us, permitting complex prognosis of economic and social development of different scale and control level systems. In the paper workability of proposed forecasting algorithms on the base of ‘K-waves’ and adequacy of created models to researched processes are proved.

Jan 1, 2003

By P. Sharma, J. C. W. Fowler

This paper discusses the wind blast / air blast phenomenon, how it is managed in coal mines and how it might best be managed in other underground mines. L'article qui suit a pour objets de décrire le phénomène de tir a l'air comprimé et les méthodes de modération de celui-ci dans les mines de houille, et d'indiquer de quelle manière il pourrait être surmonté dans d'autres mines souterraines. Dieses Seminararbeit diskutiert die Windexplosion / Luftexplosion Phänomen, wie es in Kohlenberg-werken geleitet wird, und wie es am besten in anderen untertage Bergwerken geleitet werden könnte.

Jan 1, 2003

By S. Matsuyama, S. Tomita, H. Kawahara, G. Deguchi

A proper management system of coal mine methane gas associated with underground mining activities is essential for the mine safety due to its nature of explosion. Optimum design of the mine ventilation and gas drainage need accurate prediction of gas flow rate emitted by mining activities. Permeability to gas, which is affected by stress conditions of surrounding rock mass, governs the emission rate of the gases. JCOAL has developed a three dimensional FEM simulation program named Mine Gas Flow 3D (MGF-3D). MGF-3D is designed to predict the volume of methane gas emitted from surrounding coal and rock seams based on stress distribution and permeability change which are determined by 3D stress analysis. In MGF-3D, stress change and/or expansion of fractured zone affected by mining is calculated at the first and then gas emission into roadways and longwall panels under the determined stress conditions is calculated using Darcy’s law. MGF-3D also can set up a number of pre-drainage holes and estimate drainage gas volume from each hole. This function makes MGF-3D remarkable program. These simulations for gas emission can contribute to mine gas utilization plan. Comparison between actual measurement of gas emission in the underground mine and simulation results has been performed and availability for the mine safety and problems with MGF-3D are discussed in this report.

Jan 1, 2003

By W. Kint

More than 10 years ago, one of MECS?s current partners KVT developed the so called SULFOX process for cleaning waste gases containing sulfuric compounds. In this Wet Acid Process (WAP) compounds such as SO2 and H2S, CS2, COS are oxidized over catalyst bed(s) to SO3 and finally sulfuric acid is formed. The individual plants are designed according the feed gas concentrations and customers requirements to keep the investment and operating costs as low as possible. MECS strongly believes the technology we propose will meet all your expectations. Thanks to our vast experience in the construction of sulfuric acid plants (MECS built over 800 sulfuric acid plants worldwide) we were able to design you a very reliable installation. MECS is offering the metallurgical industry, besides our conventional acid plant technology (for strong SO2) and our DynaWave? scrubbing technology (for very low SO2), a SULFOX wet acid plant (for the mid range SO2 concentrations) including an optional upstream DynaWave gas cleaning plant if required. See the figure below. Besides providing advanced technology, MECS is the only company who designs and manufactures its own key critical equipment. We manufacture our own catalyst, mist eliminators, acid distributors and coolers. Because of our in-depth technology knowledge, we understand the critical aspects necessary for making optimum equipment designs. With this combined supply of technology and key critical equipment, we can make a single overall guarantee second to none other in the world.

Jan 1, 2009

By V. Riihimäki, M. Luotamo

The Unit of Toxicological Risk Assessment of the Finnish Institute of Occupational Health (FIOH) is conducting a 'Health Risk Assessment for Metallic Chromium and Trivalent Chromium' under the sponsorship of the International Chromium Development Association (ICDA) and the International Stainless Steel Forum (ISSF). This risk assessment will be conducted in accordance with the current European Union legislation in force (Council Regulation 793/93/EEC, Commission Regulation 1488/94/EEC, Dir. 67/548/EEC), but also to meet the regulatory obligations as set out in the European Commission REACH legislation proposal (Consultation Document, the Registration, Evaluation, Authorisation and Restrictions of CHemicals). Further aims include outlining the criteria for the setting of occupational exposure limits for metallic chromium and trivalent chromium compounds. Human Health Risk Assessment according to the current legislation shall entail hazard identification of the toxic end points (acute toxicity, irritation/corrosivity, sensitisation, repeated dose toxicity, mutagenicity, carcinogenicity, reproductive toxicity) including, as appropriate, dose (concentration) - response assessment, and derivation of the N(L)OAELs (No (Lowest) Observed Adverse Effect Level) and/or DNELs (Derived No Effect Level). Exposure assessments for workers, consumers and humans exposed via the environment take into account all the known intended uses. Risk characterisation will compare the typical and/or reasonable worst case exposure estimates to the N(L)OAELs or DNELs to determine Margins of Safety (MOS) for all human populations by each exposure scenario and type of effect, followed by conclusions about the presence or absence of risk. Although all of the key elements of existing legislation remain in REACH, the principal change is that, the burden of proof will be transferred from the member state authorities to industry. The new proposed format of Chemical Safety Report (CSR) will include Risk Management Measures (RMM) as an essential part of the report in addition to the risk assessment. The RMM plays a role in the evaluation of further testing needs and advocating reasons for possible waiwer of requirements. The research programme started in March 2002 and will be completed within the time frame of two years.

Jan 1, 2004

[Ferro Alloys Producers Association The South Africa Institute of Mining and Metallurgy www.saimm.co.za Mintek www.mintek.co.za Eskom www.eskom.co.za ]

Jan 1, 2004

By B Vorster

Falls of Ground is one of the highest causes of incidents, accidents and fatal injuries in our mines today. These falls of ground may occur as soon as the face is exposed after blasting or after machine cutting. The falls of ground can also occur after support has been installed. There are many reasons why these falls occur before and after supporting of the face. It is therefore important to support the exposed face as soon as possible to prevent the falls of ground. It is also very important to support the face with the correct support products and to support the face as designed and required by the mining engineers. The possible reasons for falls of ground, possible support methods and the products available will be discussed in this presentation. In typical conventional narrow vein stoping operations, the use of conventional temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The author wishes to discuss the following items in this paper:- ? Introduction ? Basic face behaviour after exposure ? Controllable Parameters ? Mining Engineers support designs ? Primary and Secondary Support ? Products available for prevention of falls of ground

Jan 1, 2008

By Y. Mitani, M. Xie, G. Zhou, T. Esaki

The assessment of landslide instability and risk has become a topic of major interest for both geoscientists and engineering professionals as well as for local communities and administrations in many parts of the world. In this paper, based on a new developed Geographic Information Systems (GIS) grid-based 3D deterministic model and taken the slope unit as the study object, the landslide hazard is mapped by the index of the 3D safety factor. Assuming the initial slip as the lower part of an ellipsoid, the 3D critical slip surface in the 3D slope stability analysis is obtained by means of a minimization of the 3D safety factor using the Monte Carlo random simulation. The failure probability of the landslide is calculated by an approximate method in which the distributions of f,c and the 3D safety factor are assumed to be in normal distributions. The assessment of the earthquake triggered landslide hazard is done by the dynamic displacement analysis using the index of the Newmark displacement. All the calculations are implemented by a computational system call 3DSLOPEGIS in that a GIS component is used for fulfilling the GIS spatial analysis function. Besides the results of 3D safety factor and probability, the possible landslide body and boundary can be three-dimensionally quantitatively identified. L’ estimation des glissement de terrain et des risques impliqués est devenu un des principal sujet de préoccupation pour les géotechniciens, mais aussi pour les ingénieurs specialisés ainsi que pour les communautés et administrations locales dans de nombreuses région du monde. Dans cette étude, basé sur un modèle de maillage 3D et une approche déterniniste couplée au Système d'Information Géographique (SIG), étudiant la stabilité des versants , le lieu d'étude à risque est maillé suivant le facteur de sécurité calculé en 3D. En supposant que le glissement initial soit la partie inférieure d'un élipsoïde, l'analyse de stabilité pour le glissement critique 3D d'un versant 3D est obtenu grace à une minimisation du facteur de sécurité en 3D utilisant la méthode de simulation aléatoire de Monte Carlo. La probabilité d'un glissement de terrain est calculée par une méthode approximative, supposant la distribution de c, f et du facteur de sécurité 3D normale. L'estimation d'un risque de glissement de terrain causé par un tremblement de terre est faite grace à une analyse du déplacement dynamique suivant l'index de Newmark. Tous les calculs sont effectués par le biais d'un système de calcul appellé 3DSLOPEGIS dans lequel te GIS est utilisé pour gérer l'analyse spatiale. En plus de cela, les résultats du coefficient de sécurité en 3D, des probabilités, le terrain susceptible de glisser, et ses limites, peuvent être quantitativement évalués en trois dimensions. Die Bewertung von Erdrutsch-Instabilität und risiko sind zu einem Thema von großen Interesse für sowohl Geowissenschaftlern und Ingenieuren als auch von Gemeinden und Verwaltungen in vielen Teilen der Welt geworden. In dieser Arbeit, basierend auf einem neu entwickelten Geografische Informationssysteme (GIS) gitterbasierten 3D deterministischen Modell und mit der Böschung als Untersuchungsobjekt wird die Erdrutschgefahr durch den Index des 3D-Sicherheitsfaktors kartografiert. Unter der Annahme, dass der erste Rutsch der untere Teil eines Ellipsoiden ist, wird die 3D kritische Schlupfoberfläche in der 3D-Böschungsstabilitätsanalyse mit einer Minimierung des 3D-Sicherheitsfaktors mit der Monte Carlo Zufallssimulation erhalten. Die Fehlerwahrscheinlichkeit des Erdrutschs wird mit einer Annäherungsmethode berechnet, bei der die Verteilungen von f,c und dem 3D-Sicherheitsfaktor als innerhalb normaler Verteilungen angenommen werden. Die Beurteilung der Erdbeben-ausgelösten Erdrutschgefahr wird mit der dynamischen Verdrängungsanalyse mit dem Index der Newmark-Verdrängung gearbeitet. Alle Berechnungen werden mit einem Berechnungssystem mit der Bezeichnung 3DSLOPEGIS ausgeführt, bei dem eine GIS-Komponente zum Erfüllen der GIS räumlichen Analysefunktion verwendet wird. Neben der Ergebnissen des 3D-Sicherheitsfaktors und der Wahrscheinlichkeit kann der mögliche Erdrutschkörper und der Umfang dreidimensional quantitativ identifiziert werden.

Jan 1, 2003

By W. A. Gericke, B. Olmstead, I. Mc Dougall, C. F. R. Smith

A finite element model was generated of a Søderberg electrode in a ferromanganese smelter. In this model, the casing and fins were modelled explicitly, and temperature-dependent material properties were included. A two-stage analysis procedure was used, the first part being a coupled thermal-electrical analysis using an applied DC current. As the casing material was non-magnetic, the DC current was deemed sufficiently accurate for this initial analysis. The proximity effect was not considered. Thermal boundary conditions based on assumed temperature distributions in the furnace were applied. Calculated temperatures agreed well with measured values. The joule heat calculated in this step was applied as a load to a coupled thermalstress analysis. The model was applied to a comparative study of alternative materials for the casing and fins. A number of different combinations of materials for the casing and fins were evaluated in a comparative study. The position of the baking zone was used as the criterion for evaluating the potential of each material combination. Based on this analysis, some material combinations were discarded as being entirely unsuitable, whilst the two most suitable combinations will be tested experimentally in the furnace. The stress analysis was performed on the most suitable option. The practical advantage of this analysis was that a number of what-if scenarios could be evaluated and discarded prior to embarking on expensive experimental work, thus limiting the amount of experimental effort required. A mathematical model allows for the comparison of options under controlled conditions, where parameters of interest can be varied individually, with all other parameters remaining the same, a condition which is difficult to achieve in an operating furnace.

Jan 1, 2004

By J. J. Geldenhuys

A colloquium on 'Developments in the Mechanization of Mining Operations' was held in, conjunction with the 1984 Electra Mining Exhibition, at the Milpark Holiday Inn in Johannesburg on 19th September, 1984. An attendance of close on 200 delegates was testimony to the popularity of the subject. The delegates included a number of visitors from abroad, including senior members of the management of foreign companies and a member of the Council of the Institution of Mining and Metallurgy, United Kingdom. Both the local and foreign press was also represented.

Jan 1, 1985

By John M. L Lewis, Antoine F. Mulaba-Bafubiandi

In the irradiation of ore particles by microwave energy preferential absorption of this energy occurs in minerals having specific dielectric properties (Bradshaw, 1999). This leads to a selective heating of the various components of within the ore particle matrix. The result is a differential thermal expansion of such components and the resulting induced stresses become ideally concentrated at mineral grain boundaries (Kingman et al., 2000). Dependent upon the relative composition of absorbent, opaque and reflective components this may lead to enhancement of the inter-granular fracture of the ore particles in the initial comminution process (Fandrich et al., 1997). The potential is thus a greater proportion of free mineral grain within the fractured ore particle that may lead to improvement in subsequent mineral separation processes. As the composition of the ore dictates the result of such a treatment (Kingman et al., 2000) it is essential to evaluate the response of each ore sample on an individual basis. This paper reports on results obtained from two ore samples: the one being the zinc ore from the Black Mountain mine (South Africa) and the other a pre-concentrated sample of handpicked cobalt?copper mixed oxide ore from the Gecamines (DRC). The equipment and methods used to simulate the comminution of the samples and evaluate the level of the value liberation will be described along with the results obtained. Using King (1975), Kanellopoulous and Ball (1975), and Gungor and Atalay (1998), a comparison between the behaviour upon microwave irradiation of sulphide and mixed oxide ores leads to conclude that while the technique (i.e. microwave irradiation) is appropriate to the zinc sulphide ore, it does not seem to lead to exceptional results for the oxide.

Jan 1, 2005

By J. A. Venter, M. K. G. Vermaak

There are practical indications that flotation recovery of palladium bismuth tellurides is poor. This work tested whether this can be caused by a lack of interaction of the collector with the telluride. Impedance measurements, voltammetry and Raman spectroscopy were performed to determine the interaction of dithiocarbonate collectors (KEX) with Pd-Bi-Te. Impedance measurements showed lower capacitance values in solutions containing KEX indicating the formation of a continuous surface layer. Anodic and cathodic polarization diagrams show the mixed potential tobe higher than the reversible potential of the xanthate-dixanthogen equilibrium reaction; hence the formation of dixanthogen on the surface is possible. Electrochemically controlled in situ Raman spectroscopy did indicate the presence of bulk diethyl dixanthogen on the surface. Raman spectroscopy has confirmed the co-presence of xanthate with dixanthogen, indicating that xanthate retains its molecular integrity when it adsorbs on the surface of the Pd-Bi-Te. As a result, the mineral surface is expected to be hydrophobic and a lack of collector interaction with the mineral is not the reason for low PGM recoveries experienced. Keywords: Raman spectroscopy; Pd-Bi-Te; ethyl xanthate; platinum flotation; Great Dyke; Pd-bearing bismutho-tellurides and moncheite.

Jan 1, 2004

By N. Kinoshita, Y. Inada

The authors have proposed and discussed storage of low temperature materials such as LNG, LPG and frozen food in rock caverns. In this case, as the rock mass around the caverns will receive effects of low temperature, it is necessary to consider the thermal behavior and the stability of caverns. In this study, strength and deformation characteristics obtained by the uniaxial tension test and the compression test at low temperatures were discussed. Using the results, temperature and stress distribution around caverns when LNG was stored, were analyzed. Then thermal behavior of the rock mass around caverns was discussed. Die Autoren haben Lagerung von Niedertemperatur-Materialien wie LNG, LPG und tiefgefrorenen Nahrungsmitteln in Felskavernen vorgeschlagen und diskutiert. Da in diesem Fall die Felsmasse um die Kavernen den Effekten der niedrigen Temperatur ausgesetzt ist, ist es erforderlich, das Thermalverhalten und die Stabilität der Kavernen zu berücksichtigen. In dieser Untersuchung wurden Stärke-und Deformationseigenschaften, die durch ein-axialen Spannungstest und Kompressionstest bei niedrigen Temperaturen erhalten wurden, diskutiert. Mit diesen Ergebnissen wurden Temperatur- und Stressverteilung um die Kavernen bei Lagerung von LNG analysiert. Dann wurde das Thermalverhalten der Felsmasse in der Umgebung der Kavernen diskutiert. Les auteurs proposent et discutent l'entreposage de matériaux à basse température, tels que le GNL, le GPL et des aliments congelés, dans des cavités rocheuses. Comme, dans ce cas, la masse rocheuse entourant la cavité subit les effets des basses températures, il est nécesaire d'étudier le comportement thermique et la stabilité des cavités. Dans cette étude, les auteurs discutent des caractéristiques de résistance et de déformation, obtenues par essai de tension uniaxial et essai de compression à basse température. En se servant des résultats, ils analysent la répartition de la température et des pressions autour des cavités, lors du stockage de GNL. Ils discutent ensuite le comportement thermique de la masse rocheuse autour des cavités.

Jan 1, 2003

By Baruch Grinbaum, Edwin Bwalya, Robert Minango, Deogratias Bukunkwe

Solvent extraction of Cu from acidic leach, using an oxime extractant, e.g. LIX 984 or Acorga is a well known and established process. As the process advances, Cu is extracted to the solvent and is replaced by H+ in the aqueous phase. At high acidity the distribution coefficient of Cu between the solvent and the aqueous phase decreases, and eventually relatively high concentration of Cu remains in the raffinate, regardless of the number of equilibrium stages. In many processes this phenomenon is immaterial, as the raffinate returns to the leaching and no copper is lost. But when the copper raffinate is used for processing of additional metals, minimal concentration of Cu in the raffinate is essential for an effective process. The recommended process includes three steps: 1. SX-1: Standard extraction of Cu with oxime. The resulting raffinate contains about 6-8 g/L Cu and 50 g/L H2SO4. 2. SX-N: Extraction of most of the acid into an amine-based solvent, and stripping it with a base, e.g. aqueous ammonia, caustic, Na2CO3 etc. The extraction removes no metals, but decreases the concentration of acid from 50 to 10 g/L. 3. SX-2: Extraction of the neutralized solution once more with oxime, to remove the residual copper. Such a process enables one to get down to 100-150 ppm Cu in the final raffinate. This process was developed and tested in the R&D facility in Chambishi Metals plc, by a joint team of Chambishi & Bateman, using Cognis LIX 984N and real solutions from the plant. In the laboratory scale, the equilibrium isotherms for SX-1, SX-2 and the neutralization were developed. Computer simulation of the results showed that the optimal configuration is two stages for both extraction and stripping for SX-1. For SX-2 2-3 stages of extraction and two stages of stripping are needed. The stripping stages may be common to both SX-1 and SX-2. The neutralization of SX1 raffinate was tested both by conventional precipitation with lime and by extraction with Alamine based solvent extraction and stripping with a solution of 10% NaOH. For the SX-N only one stage was needed for both the extraction and stripping. The bench scale pilot plant was run for both SX-1 & SX-2. The results were very similar to the simulated ones, and the configuration of 2E2S for SX-1 and 3E=2S for SX-2 delivered the required raffinate with less than 150 ppm Cu.

Jan 1, 2005

This publication is provided on an "as is" basis without warranties of any kind, either expressed or implied including, but not limited to warranties of title or implied warranties of merchantability of fitness for a particular purpose. The information contained in this publication is for general information purposes only. It does not constitute professional, technical, financial or other advice to the user of this publication and must not be relied upon as such by any person whatsoever. The use of this publication is at the users own risk. The authors/creators of the information contained in this publication have tried to ensure that the information contained herein is correct, but errors or inaccuracies may exist or the information may be incomplete, unreliable or no longer up to date. Therefore, no warranties of any nature whatsoever are given and any liability to any person in respect of anything and in respect of the consequences of anything done or omitted to be done, wholly or partly in reliance upon the whole or any part hereof, are disclaimed, including and without limitation any contractual, dialectal, direct, consequential or financial damages or losses. On no account will Organisers and/or any of the contributors or any person or entity involved in creating, producing or distributing the information and or software available in this publication be liable for any such damages arising out of the use of or inability to use this publication. Copyright Reserved The South African Institute of Mining and Metallurgy P O Box 61127, Marshalltown 2107, South Africa www.saimm.co.za All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without the written permission of the copyright owner. Although the greatest care has been taken in the compilation of the entire contents, the editors and publishers do not accept responsibility for errors or omissions. First Edition Copyright February 2004 Proceedings ISBN: 0-9584663-5-1 (1 volume and CD-ROM)

Jan 1, 2004

By Baojun Zhao

Primary lead production using the lead blast furnace in conventional practice is carried out using sinter feed. At YMG, China, the sinter plant has been replaced with a lead ISASMELT furnace. The ISASMELT furnace produces lead bullion plus a high-lead slag, which is cast into lumps to provide a suitable feed for the blast furnace. In the present study the relative microstructures and reduction characteristics of industrial lead sinters and synthetic ISASMELT slag in CO/CO2 gas mixtures have been measured and compared. The microstructure and property changes, and the mechanisms of reduction in each case are examined and discussed. The results of the study are used to explain the successful implementation of cast slag feed in commercial ISASMELT- lead blast furnace practice. Key words: lead slag, lead sinter, lead blast furnace, reduction kinetics and mechanisms

Jan 1, 2008

By Z. Jin, Q. Yun, C. Lu

This paper presents a quantitative assessment model for the assessment of environmental load in gold production, which is based on environmental ecology, Life-Cycle Assessment and technical conditions of gold production in China. This model can make environmental assessment in terms of a set of indexes and quantitative approach by means of artificial neural network, which also improves the theory of Life-Cycle Assessment. Keywords: Artificial neural networks, Environmental load, Assessment, Utility function, Gold production

Jan 1, 2003