Search Documents

By Robert H. Essenhigh

A stirred reactor (SR) combustion system has been developed to gather information on the mechanisms of ignition and flame propagation of coal dust under conditions similar to those found in coal dust explosion flames. The prime scaling variable considered in this study is that of rapid particle heating (between 105 and 106°K/sec) which is accomplished by means of turbulent mixing during combustion. The SR combustors tested in this study have consisted basically of spheres hollowed in the centers of refractory housings. Coal and air mixtures have been injected into the spherical combustion chambers through a single jet, two opposed jets or four opposed jets. The diameters of the jets have ranged from 0.63 to 0.22 cm. The volumes of the combustion chambers have ranged from 1.0 to 0.2 liters. The reactors have been equipped with thermocouples embedded in the combustion chamber wall as well as a thermocouple located in the exhaust gas stream. In the latter versions of the SR, provisions were made for both solid sampling and gas sampling of the reactant stream exiting from the combustion chamber. Experiments have been carried out using pulverized bituminous coal. The coal has been reacted in an SR in mixtures of air and air/nitrogen. These experiments have provided information on the mode of ignition of the coal as well as yielding information on the kinetics of coal pyrolysis through the use of SR theory. Ash tests performed on the reacted samples collected from the SR indicated that the majority of the values of weight loss percentage were between 60 and 70 percent. The percentages of weight loss were relatively unaffected by changes in temperature which varied between 1100 and 1700°K and by changes in residence time which varied between 10 and 20 millisec. Volatile matter tests performed on the samples indicated that the volatile matter left in the char ranged from 3 to 20 percent of the original content. By assuming that all the mass loss was due solely to pyrolysis with no combustion occurring at the particle surface, Q-factors for each test have been calculated. The results of these calculations indicate an average value of Q equal to 1.88. This finding shows that the majority of mass loss can be attributed to pyrolysis. The fact that the extent of reaction varies only slightly over the range of test conditions has been examined in the context of the two component hypothesis of coal constitution. This approach leads to the conclusion that the reaction of the "easily evolved" component VMI is extremely rapid and that the majority of it is removed from the coal in times less than the residence time in the system. This means that the volatile residue remaining in the char can be considered to consist of component II, VMII. If the mass fraction of VMI = 0, then an activation energy of 18.0 kcal is obtained for the pyrolysis reaction. If the mass fraction is assumed to be 0.75, the activation energy increases to 31.2 kcal.

Jan 1, 1978

By J. G. Groetsch

Municipal solid waste (MSW) contains about 8 pct ferrous metallics which are typically recovered by magnetic separators at municipal resource recovery facilities. At present, only about 182,500 ton/yr of MSW magnetics are being processed for remelting out of the -11 MMton/yr discarded. The Sn in MSW magnetics makes this material difficult to recycle to the steel industry. An electrolytic method using stannous fluoborate-fluoboric acid for removing Sn was evaluated. Optimum concentrations of Sn in the electrolyte and the effects of impurities such as Al, Cu, Fe, and Pb on Sn recovery from the electrolyte were evaluated. Operating parameters were 60 to 65 g/L fluoboric acid and 20 to 30 g/L Sn using stainless steel electrodes at a current density of 60 A/ft2. Tests were run with postconsumer scrap4 and MSW magnetics. Good results were obtained with MSW magnetics, after pretreatment by reshredding, magnetic separation, and air classification. The final Sn content of the MSW magnetics scrap was reduced from 0.18 to 0.017 wt pct. Heat and solvent treatments of MSW magnetics to remove coatings did not significantly improve Sn removal beyond that obtained with material that had only been mechanically pretreated.

Jan 1, 1984

By Thomas E. Green

A combined solvent extract ion-spectrophotometric method for the determination of as little as 1 ppm of copper in tungsten metal or tungstic oxide has been developed and evaluated. Metallic samples are converted to tungstic oxide by treatment with hydrofluoric and nitric acids. The oxide is then dissolved in sodium hydroxide, and the copper is extracted as the colored neocuproine complex. Total elapsed time for the analysis is approximately 1-1/2 days; however, actual working time for a group of six or eight determinations is less than 4 hours. Precision at the 2-ppm level is better than 0.1 ppm.

Jan 1, 1963

By C. W. Owings

When explosions have occurred in mines where rock dust has been used to some extent, generally to a very limited extent, the press has immediately characterized those mines as "rock-dusted." To persons familiar with the method of rock-dusting, it is apparent that if rock-dusting is done properly, if all mine surfaces are rock-dusted to within at least 40 feet of the faces of rooms and entries, and if the incombustible content of the dust is more than 65 per cent, there is little likelihood that an explosion of coal-dust will occur. The report that an explosion has occurred in a "rock-dusted" mine immediately conveys to the mind of the alert safety advocate the information that the mine is inadequately rock-dusted or that either dust sampling of the rock-dusted surfaces has not been done or, if done, the mine has not been redusted with sufficient promptness. Rules for Collection of Samples Collection of dust samples is by no means intricate, but a few simple rules must be kept in mind if the results are to be dependable. A sample must represent the true average conditions of the dust in the section or zone in which it is taken, and therefore 'the point at which the sample is to be collected must be selected with care. During an explosion much if not all of the dust on the ribs, roof, timber, and road in the affected region is blown into the air; the sample, therefore, should contain all loose dust and material on: the surfaces to a depth of about 1 inch, if that amount is present. If there is considerable sand locally along the track, care must be taken not to include enough of this material to vitiate the sale and distort the results; however, if the sand is distributed throughout the region being sampled it should be included. Dust should not be collected from recesses in the ribs, such as hitches cut for timber, as the character of the dust in such places is often different from that on the ribs proper. Samples should not be collected at points where the dusting machine has been loaded or at a point where the machine has stopped and discharged for a longer period than at other points on the entry or in the rooms. In short, the sample must represent AVERAGE CONDITIONS, and if there is any doubt as to the character of the dust it is far better to have too much combustible matter than too much incombustible matter in the sample, as it is best to err on the side of safety if it is necessary to err.

Jan 1, 1929

By John Millhiser, Stephen J. Kravits

The U.S. Bureau of Mines preproduction Wireless Survey System (WSS) and its performance during an in-mine test are discussed in this report. The WSS was developed to reduce downhole surveying time in order to increase the efficiency of drilling long horizontal methane drainage boreholes in coal. Borehole survey data are electromagnetically transmitted from the WSS7s downhole guidance probe, via the drill rod, to the uph'ole subsystem in less than 1 min per survey transmission, regardless of borehole depth. The WSS7s in-mine test consisted of providing borehole survey data during the directional drilling of a 2,538-ft horizontal methane drainage borehole in the Pittsburgh Coalbed. By considering available drilling time, which does not include hydraulic drill downtime and the time spent traveling portal to portal, 24 shifts were needed to complete the borehole. Of the available drilling time during the tcst, 50 pct of the time was spent drilling and 50 pct surveying and maintaining the WSS to keep it operational. Previous Bureau experience indicates drilling efficiency was increased 108 pct because of the WSS, in comparison with using a commercially available wire-run directional survey instrument at 10-ft intervals.

Jan 1, 1990

By A. L. Pierce

This paper describing the mining practice at the Spring Hill mine of the Montana Mines Corporation, Helena, Mont., is one of a series issued by the Bureau of Mines on mining methods and costs in various districts. Its purpose is to summarize improved methods whereby lower costs have recently been obtained. These improvements are principally the adoption of a modified sublevel stoping method of mining the use of grizzlies underground improvements in haulage, and rage bonuses. The Sprint Hill, Trine is situated in Grizzly Gulch, 3 miles southwest of the city of Helena. Helena is on the links of the Northern Pacific and the Great Northern Railways; and the East Helena smelter of the American Smelting and Refining Co. to which the concentrates from the mine are shipped, is but 6 miles east of Helena. The mine is probing 150 to 200 tons of gold ore per day, with an underground crew of about 40 men.

Jan 1, 1931

By John C. Machisak

THIS CHAPTER reports employment data and injury experience in the metal, nonmetal, quarrying, sand and gravel, and slag (iron blast furnace) industries of the United States in 1959. Each industry is treated separately, and no attempt has been made to combine data to show an overall total for this group of mineral industries. The slag canvass is included for the first time (data on employment and injuries were not collected before 1958), and, like other canvasses included in this chapter, data are voluntary. Employment and injury experience for all mineral industries can be found in volume III. The employment and injury information in this chapter came from reports submitted to the Bureau of Mines before May 31, 1960; therefore, figures are preliminary and subject to revision. Voluntary reports submitted by operators have contributed substantially to safety promotion since 1911, when the Federal Bureau of Mines started collecting employment and injury facts.

Jan 1, 1960

By Verne S. Mutton, William A. Slivensky, Eric S. Weiss, Kenneth L. Cashdollar, Deepak R. Kohli

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, cooperated with Tecrete Industries Pty. Ltd. and BHP Australia Coal in a research program to evaluate the strength characteristics and air leakage of four seal and two stopping designs for use in underground coal mines. A fundamental safety research area for NIOSH is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach to achieve this goal is to develop new and innovative seal designs that provide increased explosion isolation protection for the mining personnel against ignitions that originate from within the gob or. other worked-out areas of the mine Full-scale seals and stoppings were constructed in the Experimental Mine at Lake Lynn Laboratory near Fairchance, Fayette County, PA. They were ail--leakage tested, then subjected to a series of explosions with average pressure pulses ranging from 25 to 500 kPa (3.5 to 72 psi). Instrumentation measured seal displacement and acceleration as a function of time, providing data to assist in the development of numerical models 1'01- future seal design. All three seals designed with Meshblock wire forlnwo~-k ant1 a lnonolithic shotcrete core withstood the first explosion test, which generated an avcr-age rnaximu~n pressure of - 140 kPa (-20 psi) while maintaining acceptable air leakage rates. These seals I-anged from 175 to 325 mm thick. They included a 2.7-m-high by 325-mm-thick seal that was tesled 27 hr after completion against this - 140-kPa explosion pressure, a special requirement of the test program. This seal survived explosions with pressure pulses up to 300 kPa (43 psi). The 2.3-m-high by 325-mm-thick Meshblock seal survived three explosion tests with overpressures up to 455 kPa (66 psi) and satisfied the air leakage criteria. A I ,200-mm-thick plug seal was constructed of two Gunmesh formwork walls in-filled with shotcrete and a 3,450-kPa (500-psi) strength Aquablend core. This plug seal survived three explosions with pressure pulses ranging 11-om 150 lo 430 kPa (-22 to 62.5 psi) with no measurable postexplosion air leakage. Two Gunmesh stoppings with thicknesses 01' 40 and 75 inln withstood explosion overpressures of 23 and 115 kPa, respectively. Anchoring all seal and stopping designs into the roof, ribs, and floor with steel "rootbolts" provided very effective boundary constraint that is critical to the performanceofstructures subject to explosion overpressures.

Jan 8, 1999

By R. E. Lindstrom

Separation efficiency of a 4 percent divinylbenzene (DVB) resin is not altered over a wide range in temperature. A 12 percent DVB resin, however, exhibits a marked sensitivity to temperature. When flow rates are high at ordinary temperatures, 4 percent DVB resin exhibits higher efficiency, but at 200° F. both resins are equal in performance. Effective separation of rare-earth mixtures may be obtained with hydrogen as a retaining ion by maintaining column temperatures above the solubility of ethylenediaminetetraacetic acid (EDTA) in the free acid form. Slightly lower separation characteristics were obtained with this method as compared with copper as a retaining ion, Recovery of 99 percent of the EDTA from spent eluting solutions that contain copper has been accomplished by a calcium-copper displacement reaction followed by EDTA precipitation. Impurities in the product are correspondingly low. Recoveries of EDTA from holmium solutions with sulfuric acid are substantial; however, those from yttrium solutions are quite modest. Radiotracer experiments show the presence of approximately 0.1 percent yttrium contamina¬tion in the recovered material. The study presented is one phase of a broad research program designed to assist the technology of separating and purifying rare-earth elements.

Jan 1, 1961

By Victor E. Kral

"INTRODUCTION The Segerstorm-Heizer property was examined by engineers 3/ of the Bureau of Mines in May and June 1942 and Mach 1943. As a result of these examination, the Nevada State Department of Highways,constructed 9.3 miles of graveled road under the mine access-road program. A magnetometer survey was made by the Geophysical Division 4/ in October 1943, and as a result the Mining Branch set up and conducted a core-drilling,project. Work on the deposit started May 24, 1944, and was suspended on July 31, 1944, but was resumed on December 4, 1944 and continued until completion on March 27, 1945.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as it, primary objective the more effective resource to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploration work, and prepares the final report. The Metallurgical Branch, R. G. Kinickerbocker, chief analyses samples and performs beneficiation tests."

Mar 1, 1947

By A. L. Murray, C. A. Allen

"In the Spring of 1919, the Industrial Commission of Utah undertook the assembling of safety orders covering metal mining operations Just at that time there appeared several articles in the mining papers advocating the licensing of hoisting engineers, so this subject was given careful consideration,The licensing of hoisting engineers means that they must pass an examination covering the mechanical features of hoists and boilers, and must have a certain amount of experience. This undoubtedly serves to get a class of hoisting engineers that are better informed about the mechanical operation and theoretical considerations in hoisting and the only room for argument against it is that it is difficult to give an examination that will determine whether or not a man is a competent hoisting engineer.A man might pass an excellent examination yet be absolutely unqualified to operate a hoist and the judgment of the mine super- intelligent would have to be depended upon to choose the right man from among those who were licensed. This difficulty of properly determining, by ordinary examination, a man's qualifications to run a hoist caused the idea of licensing' in the ordinary sense of the word to be abandoned; but, as there was no question that a hoisting engineer should be physically fit, it was decided to require a medical examination, and at the same time to require the hoist engineer to state his experience, so the State would better knowledge of his general qualifications.The orders covering the question were therefore issued as follows;"

Jan 1, 1920

By M. J. Friedel, D. F. Scott, T. J. Williams

In an effort aimed at monitoring mining-induced stress changes that may influence ground failure, the US Bureau of Mines conducted a series of active 3-D seismic tomographic surveys at the Homestake (Lead, South Dakota) and Lucky Friday (Mullan, Idaho) mines. Existing rock bolts were used to mount geophones and as strike points for introducing seismic energy using a 3.6 kg sledge hammer. Travel time measurements were recorded spanning up to 160 m between drifts at several levels. The tomographic uncertainty was minimized by computing iso-velocity surfaces of constant probability based on statistics from multiple reconstructions and a threshold criteria. Periodic imaging using tomographic velocity surfaces demonstrated that temporal and spatial changes in the local stress field occurred in response to ground failure and stope advancement at a gold and silver mine, respectively. Keywords: Temporal imaging; Mine-induced stress; Seismic tomography; Geophysics

Sep 9, 1996

By Richard Havens

Samples of low-grade oxide manganese ores were procured from two southern Utah properties by examining engineers of the Bureau of Mines during an investigation of manganese mineral deposits of continental United States. A 2-ton lot of ore was obtained from the Blackbird group of mining claims in Paiute County, 11 miles southeast of Marysvale, Utah. The deposit was described as an intrusive sheet or sill of altered brecciated rhyolite cemented together by manganese oxide minerals. A 2-ton sample from the Black John property, situated 32 miles northeast of Kanab, Kane County, Utah, was taken from open cuts on the vein. The blanket-type vein deposit consisted of nodules and streaks of manganese imbedded in compact gray clay.

Jan 1, 1949

By J. J. Demeter

Anthracite from the four producing regions in Pennsylvania was both ashed in the laboratory and burned on a chain-grate stoker to determine the sulfur-retention properties of its ash. The retention of sulfur in laboratory-prepared anthracite ash was shown to be related to ashing temperature and to the amounts of sulfur and calcium present in the coal. At the usual laboratory ashing temperature of 750° C sulfur retention ranged from 0.8 to 13.2 percent of the total coal sulfur. Sulfur retention in the ash was negligible, o to 0.3 percent, at 1,200° C, which is the thermal decomposition temperature of calcium sulfate; thus calcium sulfate does not form and cannot serve as a sulfur-retaining agent. In several tests the anthracite was mixed with 6 or 10 percent dolomite prior to firing in the chain-grate stoker. The dolomite did not improve sulfur retention owing to the high temperature in the fuel bed. Sulfur retention was, however, related to the unburned carbon in the ash. The relationship of the percentage of original coal sulfur retained in the ash (Y) to the percentage of the original carbon in the coal remaining in the ash (X) is expressed by Y = -0.579 + 0.914X. The percentage of sulfur retained is almost directly proportionate to the percentage of original coal carbon in the ash.

Jan 1, 1968

By Arnulf P. Hagen

This project was designed to explore the suitability of using fluorinated inorganic materials as solvents for the in situ mining of thin seamed, heavily overburdened coal; to build a data base for the selection of an inorganic solvent for use for coal cleaning; to determine if fluorinated solvents will reduce the organic and inorganic sulfur contents of the coal, as well as to lower the ash content. The coal samples have been combined with pure solvent, as well as with aqueous solutions at atmospheric pressure and at increased pressure. The increased pressure experiments are important since they duplicate the conditions anticipated for an in situ cleaning and mining operation. Trifluoroacetic, difluorphosphoric (phosphorodifluoroidic), and trifluoromethanesulfonic acids have been found to be effective for the cleaning of high sulfur, high ash coal at 300°C and at atmospheric pressure. At pressures up to 20,000 psi the effectiveness of these reagents is not decreased.

Jan 1, 1983

To improve the reliability of the Bureau developed bore-hole gage now widely used to determine the absolute state of stress in rock. Approach Use the knowledge gained by extensive field tests to design a more rugged and reliable Instrument using lighter and stronger materials. How It Works The original gage consisted of a stainless steel cylinder 1-3/8 Inches In diameter and 10-1/2 inches long. The new gage is made from titanium. This lighter material reduces the weight of the gage by 43 percent, which enhances the gage placement and depth of overcoring in vertical up? holes. For added strength, the titanium case and placement end are now threaded to the gage body instead of using screw fasteners. Three pairs of strain gaged transducers are positioned to measure the diametral deformation of a 1-1/2 diameter borehole at 60-degree intervals around the Inner surface of the borehole. Each transducer consists of a beryllium copper cantilever with a strain gage cemented on each side. These transducers are secured Into the gage body by a tapered shank for minimal creep. The transducers opposite each other are wired together to form a 4-arm external bridge circuit. A pair of transducers is referred to as a component. Any deformation of the borehole, which occurs during overcoring, is detected by pistons which translate the motion to the components. Each

Jan 1, 1982

By Mark I. Copeland

The Bureau of Mines discovered that silicon and nickel additions can prevent the formation of copper alloys of Sn, Sb, and As on the surface of steel during reheating to hot-working temperatures. When molten, these copper alloys cause surface hot shortness during hot working. Wrought steels were reheated isothermally and by simulated industrial practice; the resulting surfaces were metallographically evaluated. The steels contained, In weight-percent, 0.20 C, 0.45 Mn, and up to 1.00 Si, 1.00 Cu, and 0.15 Ni, and up to 0.30 Sn, Sb, or As. The larger the Cu, Sn, Sb and As content of the steels, the greater the amount of silicon necessary to prevent copper alloy formation. A content of 0.10 Ni considerably decreased the amount of silicon necessary for copper steels containing tin and antimony, but not for those containing arsenic. Theories for the beneficial effect of silicon and nickel additions are presented.

Jan 1, 1975

By Ruth F. Brinkley

This report is the 17th of a series originally issued annually, and more recently bienially, to acquaint the reader with the work of the Division of Explosives Technology, Federal Bureau of Mines. It differs from preceding reports in that its material is presented in two parts: Part I reviews briefly the overall activities of the Division during fiscal years 1955 and 1956;4/ part II presents in abstract form, the publications of the Division during that period. As it is not unusual for research completed in the course of one report period to be published only in the following period, the Bureau believes that the present approach will give a more accurate presentation of its work for the period considered. The Bureau hopes too, that the somewhat more concise presentation will prove convenient to the reader.5/ PART I -RESEARCH AND TECHNOLOGIC ACTIVITIES The activities of the Division during fiscal years 1955 and 1956 reflected the steadily growing preoccupation with factors affecting the safety of permissible explosives and those affecting the tests used for approval of these explosives. Findings by a team of French investigators prompted a study of the influence of atmospheric moisture on the ignition of firedamp by

Jan 1, 1961

By H. N. Smith

IN 1944 the Congress passed the Synthetic Liquid Fuels Act that authorized the Secretary of the Interior, acting through the Federal Bureau of Mines, to conduct basic research and construct and operate demonstration plants to produce synthetic liquid fuels from coal, oil shale, and other substances. As a basis for the oil shale investigations to be undertaken in this country, the progress of foreign countries in developing and using oil shale as a source of liquid fuels was studied by the technical missions of the Federal Bureau of Mines. Oil shale mines, retorting plants, and refineries were visited; geological information on the nature and occurrence of the foreign oil shales was obtained; and samples of the oil shales were collected where possible. Samples collected by these missions or acquired by other means came from Australia, Brazil, Canada, France, Manchuria (China) , New Zealand, Scot-land, Spain, Sweden, Thailand, and Union of South Africa. These countries represent a large part of the locations where oil shale developments have taken place. The major omissions are the Estonian, German, and Russian developments.

Jan 1, 1959

By Paul Hopkins

The following methods have been selected from a large number tried while assaying several hundred samples of placer concentrates. It is thought that some of these methods may be useful to those who are required to assay similar products containing large quantities of metallic articles, such as jeweler's sweepings. No great difficulties will be encountered in assaying black sand from beaches or river bars. Such samples require care in grinding and sifting so that no oversize particles of gold or platinum are lost. It is also necessary to have sufficient silica in the flux to form a fluid slag with the excess of iron, magnesium, or chromium which such samples contain. It is much more difficult to assay black sands, or concentrates, produced in large-scale placer-mining operations. These products are usually much harder and more abrasive than the beach black sands. They also contain numerous metallic particles resulting mainly from wear on the mining machinery. These particles consist chiefly of iron or steel but also contain lead, copper, and alloys such as babbitt, solder, brass, ferrosilicon, etc. Fairly large particles of gold are often found. Some samples will contain as much as 10 percent of such metallic particles. It is not feasible to remove the particles of iron with a magnet and discard them, as they invariably contain gold, sometimes a considerable amount. This gold is attached to the iron particles by rust or wedged into cavities. Scraps of sheet iron are often found which have become tightly folded or rolled and contain gold or amalgam within the folds.

Jan 1, 1934