Search Documents

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Clarion County, Pa. Of the 15 samples collected, 1 was of metallurgical quality as received, 4 could be sufficiently upgraded to provide acceptable products, and the remaining 10 samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, 1 sample was of low sulfur content as received, 1 sample could be upgraded to low sulfur content, and 10 samples could be upgraded to medium sulfur content. The original sulfur content of the remaining three samples can be appreciably reduced by removal of the sink 1.58 specific gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1968

By Peter J. Clarke

Development of the mineral and energy resources of Afghanistan appeared to be a top priority of the Soviet-controlled Government in the country. In the Afghan Government's plan for 1980-81, the largest allocation in the development budget was for mines, industry, and energy (46.7%). In contrast, only 23.1% of the budget was allocated for agricultural development, despite the fact that the great majority of the population was dependent on farming. The mineral industry of Afghanistan consisted of the production of natural gas, cement, coal, fertilizer materials, and rock salt. Production levels for all of these commodities were down an average of 45% from those of 1978, before the Soviet invasion. Prior to the invasion, small quantities of asbestos, barite, and talc had been produced along with about 6,000 to 7,000 kilograms per year of lapis lazuli, a semiprecious gem stone. Afghanistan had supplied about 80% of the world's output of lapis lazuli. Following direct Soviet intervention, production of these minerals declined to near zero.

Jan 1, 1983

By Rudolf Kudlich

"The realization that fuel costs, high as compared with those enjoyed prior to the war, are apparently permanent, has caused steam power plant operators to apply their best efforts towards improving the fuel economy of their plants.Though they have given much attention to the reduction in combustion losses by improving methods of firing and improved equipment, and to diminishing the heat losses by more care in maintaining clean heating surfaces and tight and adequate baffling, they have almost universally neglected the waste that occurs from discarding unconsumed combustible with the boiler refuse.This loss varies between extremely wide limits, depending on the quality of the coal, the type of plant and the firing practice in general, the higher the ash content of the coal the greater will be the amount of combustible appearing in the refuse, and the losses will be greater as the boilers are driven at higher ratings. The refuse from stoker fired boilers is apt to have a lower aver-eve percentage of combustible than that from hand fired boilers if operated at the same rating, but stoker fired boilers are usually pushed to higher ratings and the combustible in the refuse will run higher.In actual operating practice the amount of unconsumed combustible in the boiler refuse may range from a few percent to as high as forty or fifty percent. In an informal statement one well known combustion engineer estimates that the average amount of combustible in the refuse from a large stoker fired central station boiler plant is about 15 or 20%. Assuming that the coal burned contains 12% of ash, and allowing for flue dust losses, approximately two percent of the coal will be lost through this channel. The operating engineer of one large modern central power plant reports that when burning coal of about the same ash content, the average amount of combustible in the refuse was in the neighborhood of 33%, en tailing a loss of approximately 4% of the heating value of the fuel fired. Where the coal used daily runs up into hundreds of tons, an appreciable economy could be effected by recovering this percentage."

Sep 1, 1924

By Leon W. Dupuy

"INTRODUCTION Scheelite occurring in tactite at the Black Rock tungsten mine, near Benton in Mono County, Calif., was investigated by the Bureau of Mines in cooperation with the Geological Survey as part of their search for additional sources of supply of strategic minerals authorized under the Strategic Materials Act. 3/4/The work accomplished by the Bureau, and the assays of samples taken are described in this manuscript. The ore found aided materially in prolonging the operating life of the mine during the recent national emergency, supplying much-needed tungsten for war use. ACKNOWLEDGMENTSIn its program of investigations of mineral deposits, the Bureau of Mines has as its primary objective the more efficient utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual development work, and prepares the final report. The Metallurgical Division, under the direction of C. C. Ralston, chief, analyzes samples and performs beneficiatibn tests."

Mar 1, 1948

By Lloyd A. Morley, Robert Stefanko

Before going directly to the analysis, it would be good to summar¬ize explosion-proof container approval methods. Both Magison (52) and Short (84) state that in general practice, the systems are certified for: 1. a rugged enclosure able to withstand an internal explosion but not allow explosively hot gases to escape, and 2. maximum surface temperature, with equipment operating inside, that will not ignite the surrounding atmosphere. Also, testing insures that any material in contact with the container surface will not be ignited by a hot spot. Associated with the first practice, the enclosures are inspected for: 1. a safe flange gap width, 2. a pressure increase during ignition, and 3. an hydrostatic pressure withstand level. The hydrostatic pressure level is almost always determined by a meas¬ured ignition-pressure test and is usually applied to prove the mechan¬ical design to some safety factor. Consequently, explosion-proof enclosure testing includes temper¬ature, permissible flame gap, and pressure. Specifications and prev¬ious research also can be similarly separated even though some interre¬lation exists between the flame gap size and internal enclosure pressure during an explosion. The Schedule 2G Sections applicable to these subjects are: 1. 18.2 Definitions; 2. 18.6 Applications;

Jan 1, 1974

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.

By D. B. Dow

"Natural gas-gasoline is made by collecting in the liquid state the condensable hydrocarbon vapors that exist in different natural gases in varying amounts. In the richer type of natural gas the gasoline is generally recovered by compression and cooling. If exceedingly high pressure or low temperature is used, there is dissolved in the gasoline a large amount of very volatile material, which evaporates rapidly at atmospheric temperature and pressure.In the leaner type of natural gas, the gasoline vapors are selectively absorbed from the permanent gases by passing the natural gas through an absorbing oil. The gasoline is recovered by distilling the saturated oil, and as compared with ""compression"" gasoline is of high Baume' gravity and low vapor pressure. Before a volatile gasoline can be transported in tank cars, it is necessary to decrease its volatility in order to lessen the risk of fire or explosion, as well as to prevent excessive evaporation in transit. This can be accomplished either by weathering the gasoline, or by blending it with a more stable material, naphtha being commonly used in the weathering process the more volatile portions of the gasoline are allowed to evaporate and the losses in volume are very large, therefore, blending is preferable, wherever possible.It is very difficult, however, to produce by blending, in gasoline plants, a motor fuel which is equal to straight-run refinery gasoline. In order to make a blended motor fuel of a grade equal to straight-run gasoline, only a small percentage of natural gas-gasoline can be blended with the naphtha, consequently it is customary to blend the gasoline with only enough naphtha to enable It to be shipped to an oil refinery when the material is again blended to form a finished motor fuel."

Sep 1, 1921

By Michael D. Fenton

Detailed comprehensive assessment of the performance of Afghanistan's mineral industry during 1987 is virtually impossible, owing to the paucity of reliable published information. It was evident, however, that the level of civil disorder, now in its eighth year since the arrival of significant numbers of Soviet troops, was in actuality little removed from open civil war. Insurgents controlled substantial areas of the country and imperiled any industrial activity in many places. Assistance programs by the U.S.S.R. and other Eastern European nations were directed at developing the country's meager mineral industry, but the economy was generally viewed as chaotic. The inflation rate was somewhere between 20% and 30%; major food shortages contributed to the discontent of the population, and numerous villages were devastated by Soviet and Afghan Government campaigns to destroy the insurgents and cut their supply routes. Moreover, proposals by the Soviets and the Kabul Government aimed at reducing tensions with the rebels and scaling down the warfare seemingly were taken by the opposition as signs of weakening by the Soviet-backed Government, and rather than reducing aggressions, seemed to heighten insurrectionist activities. Efforts to entice the substantial number of Afghans who have fled to nearby areas of Pakistan and Iran to return to their country seemingly were failures, and indications near yearend that the Soviet Union might soon begin withdrawal of its occupation force of nearly 120,000 did little if any to reduce disorder.

Jan 1, 1989

By Raja V. Ramani, Robert L. Frantz

"In response to the U.S. Bureau of Mines (USBM) Request for Proposal (RFP) for "" the establishment of a Generic Mineral Technology Center (GTC) in Respirable Dust,"" the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with participating MRIs at Massachusetts Institute of Technology (MIT), and the University of Minnesota (UMN) have prepared the comprehensive research program described herein. Michigan Technological University (MTU) joined the Center as an affiliate after its inception. This program was developed with recognition of the stated objective of the Federal Mine Safety and Health laws which is to "". . . permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease . . . .""Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic consequences and some others, slow and long enduring, has been a major concern for labor, management and the government. This concern has manifested itself in four mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) interaction of dust and lung control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workman's compensation laws for occupation related health deterioration."

Aug 31, 1989

Coaxial cable structures form the subject of substantial theoretical and experimental investigations either directly related, or which can be extrapolated, to the communications needs and environments of U.S. coal mines. Communication systems based on "guided" waves, of which "leaky" coaxial cables are one implementation, are attractive candidates for providing a range of communication functions primarily along haulage ways, and possible also within sections up to the working face. (However, there are still strong reservations as to whether a practical coaxial cable sys tem could provide sufficient communications coverage within a section. ) In this Part, we present the results of some theoretical calculations of the performance of leaky coaxial cable communication systems. We also analyze the applicability of the theoretical and experimental results obtained by other researchers to the needs of U.S. coal mines. In particular, this investigation has been focused on the utility of relatively low cost, conventional, flexible, coaxial cable at frequencies covering the LF through HF bands and extending into the lower part of the VHF band, as opposed to relatively high cost, special semi-rigid, coaxial cable* at frequencies in the VHF and UHF bands. There are three major design alternatives for coaxial cable communication systems considered in this chapter: • Base station feeding a coaxial cable with high surface transfer impedance (holes in outer conductor, e.g., braid construction). • Base station feeding a coaxial cable with repeaters (U.K. experiments). • No base station, direct communication via a coaxial cable with periodic radiative structures.

Jan 1, 1974

By James R. Aggson

The theoretical relationships that are used to calculate in situ rock stress magnitudes and directions from borehole deformation data obtained during overcoring are based on the assumption that the rock is a linearly elastic material. Strictly speaking, this assumption is not valid in any rock. Thus, investigators using overcoring techniques must either accept various degrees of nonlinearity and the associated inaccuracies or use core testing techniques that address the problem and compensate for elastic nonlinearity. Previously developed test procedures for stress-relief overcores partially correct for nonlinearity. This Bureau of Mines paper describes a test procedure that completely corrects for elastic nonlinearity in stress-relief overcores.

Jan 1, 1977

Water infiltration control techniques are designed to reduce the total volume of water entering an underground mine, and thus, reduce the volume of mine water discharge During the development of underground mines, water may be encountered in various quantities This water must be pumped from the mine during active mining, and in many situations, the weight of water removed will be more than the total weight of mineral extracted After abandonment of the mine, infiltrating water either floods the mine workings or discharges from the mine (27, 127) Infiltrating water may enter underground mines from above, below, or laterally through adjacent rock strata Earth fractures such as faults, joints, and roof fractures resulting from surface subsidence are commonly primary causes of water entrance Into abandoned underground mines Factors affecting the quantity of water entering a mine will be the depth of the mine, location of water bearing strata, and ground water flow patterns Investigations of the quantity of water entering underground coal mines have found the average rate of infiltration to range from approximately 6,262 to 10,280 liters per hectare per day (670 to 1,100 gal/acre/day) (27) Water flowing through underground mines flushes pollutants from the mine and may result in their discharge to the environment A reduction in the amount of flow usually results in a reduction in total pollution load discharging from the mine The techniques discussed in this section can be used to reduce the volume of surface and groundwater available to enter the mine system and transport pollutants The selection of a control technique will depend upon the characteristics of the mine system and the expected cost effectiveness of the technique In order for water infiltration control to be effective in controlling mine drainage pollution, the reduction in mine water flow must not be accompanied by an increase in concentration of pollutants (127) REFERENCES 2, 27, 51, 58, 127, 132

Jan 1, 1975

By J. S. Browning

The Bureau of Mines investigated the concentration characteristics of high-clay sylvinite ores from potash companies operating in the Permian basin near Carlsbad, N. Mex. These ores, containing 14 to 19 percent K20 and 3 to 5 percent clay slimes, cannot be effectively processed by current commercial flotation methods because of their high clay content. A solution to this problem was shown to be the use of two-stage moderate scrubbing conditions for clay disaggregation and removal as opposed to strenuous attritioning. Bench-scale beneficiation techniques for recovering potash minerals by flotation from the scrubbed material resulted in acceptable product grades and recoveries. By using a coarse grind, emphasis was placed on production of premium granular and coarse products. Flotation results showed that concentrates of 59.6 to 60.4 percent K.0 values can be obtained. Continuous pilot plant beneficiation techniques for recovering potash minerals by flotation resulted in concentrates containing 58.8 to 59.8 percent K20 with recoveries of 69.7 to 81.4 percent of the K20.

Jan 1, 1975

By John Durkin

Field studies have been conducted in a large number of coal mines throughout the U.S. to determine the effectiveness of electromagnetic techniques in locating men trapped underground following a mine disaster. Data from these tests have been used to generate models of expected signal and noise distributions as found above mines throughout the coal fields. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results indicate an expected 45% probability of detecting a miner's signal from a depth of 1,000 ft, a depth which exceeds 903 of the coal mines within the U.S. and a 90% probability at a depth of 500 ft, a depth which exceeds 50% of the mines.

By H. O. Poppleton

This Bureau of Mines study was made to investigate a possible method for selectively removing the Si02 component of silicate minerals and ores. Of specific interest were aluminum ores and zircon. Methods are described for removing Si02 from these ores as volatile silicon sulfides by treating the ore with sulfur and carbon; with sulfur, carbon, and a reducing gas; or with sulfur compounds and carbon. Comparative results are also given for the desilication of some of the ores with carbon alone to form volatile silicon monoxide. The silica component can be removed partially from bauxites at temperatures above the sublimation temperature of SiS (940° C) by treatment with carbon, sulfur, and methane; however, it is more difficult to remove the silicon from kyanite, manganese silicate, red muds from aluminum processing, kaolinite, lateritic nickel ores, and zircon. Complete desilication requires temperatures ranging from 1,100° C for bauxite to 1,450° C for zircon. Although the high temperatures required and the undesirable metal sulfides produced eliminate practical application of this method using present technology, the Bureau is reporting this data so that they will be available to future investigators.

Jan 1, 1974

1. In 2003, 14,391 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). Almost half (49%) were sand and gravel mines, followed by stone mines (30%), coal mines (14%), nonmetal mines (5%), and metal mines (2%).

Feb 1, 2005

By Manuel Gomez

A computerized moving average technique was developed to interpolate coal seam characteristics between sample points. The interpolative method coupled with multivariate regression analysis and simulation procedures was used to forecast coal properties not readily obtained from an analysis of drill core samples. Coal property forecasts were of two kinds: (1) specific mine property forecasts that are suitable for mine product control and yield a good approximation of the local variation along both the vertical and horizontal axes of the seam, and (2) regional estimates where much of the local seam variation is smoothed out, but the general trends are maintained. Forecasts of the volatile matter, ash, total sulfur, and the heating value for part of the Pittsburgh seam located in Ohio, Pennsylvania, and West Virginia were in good agreement with independent evaluation data. Spatial configuration for preparation characteristics, particularly, the effect of crushing on sulfur release, low-and high-temperature carbonization properties, the Hardgrove grindability index, the coal hardness index, gasification variables, and hydrogenation factors were constructed for the same area of the Pittsburgh seam. These forecasts may be developed from drill core data collected in the exploration phase of mining. The results, which may take the form of a series of maps, are useful to mining, chemical, and combustion engineers, to economists and mine managers, as well as to coal users for mine design, economic analyses, energy forecasts, utilization studies, mine product control, and environmental control and programming.

Jan 1, 1974

By H. O. McDonald

The Bureau of Mines reviewed the chemical vapor deposition (CVD) literature on the nonmetal binary and ternary compounds of the group IVB, VB, and VIB elements, with emphasis directed to the following nonmetals: B, C, N, O, and Si. This review examines each of these binary and selected ternary compounds of the group IVB, VB, and VIB elements as coatings and gives some of their preparative methods, uses, and properties. A total of 259 references were found for these compounds of the nine elements. This review was utilized in the Bureau's research to provide abrasion-, erosion-, and corrosion-resistant coatings in order to conserve critical metals and protect various metallic surfaces in metallurgical, mining, and energy conversion systems.

Jan 1, 1983

By Fred A. Williams

The cause of many deaths and extensive property damage in coal mines resulting from explosions and mine fires has been directly attributable to electric cable failures (including splice failures). The Federal Bureau of Mines data show that out of 355 underground coal mine fires investigated from July 1952 to January 1960, 103 (29 percent) were directly related to trailing cables. These cable failures resulted in the death of 7 men and injuries to 37 others. These potential hazards have become greater, obviously, through the widespread adoption of mechanized mining methods with electric-driven machinery powered through trailing cables according to Young,4 68.1 percent of the total bituminous and lignite production of the United States was mined underground in 1959. About 85 percent of this production was attained by mechanized loading methods. A large majority of the mines using the hand- loading methods also used equipment with trailing cables such as cutting machines, drills, and gathering locomotives. The problem of minimizing the loss of life, resources, and equipment from cable failures should be of concern to the management of all coal mines. It would be misleading to imply that no consideration has been given to the problem and its associated hazards. Through research cable manufacturers have endeavored to develop trailing cables that will withstand the severe service imposed by underground mining conditions. Technical research groups have undertaken studies for determining improved procedure and materials for field splices. Coal companies have instituted cable maintenance programs with a view toward the reduction of cable failures and consequent improvement in safety and efficiency of operations. Safety agencies are alert to unsatisfactory cable handling practices, poor workmanship in field splicing, mechanical

Jan 1, 1962

By Bill M. Stewart, Phil W. Patton, Curtis C. Clark

Back injuries from handling materials in underground mines continue to be a major safety problem. In spite of the ingenuity of many people and the development of numerous mechanized aids, the number of materials-handling injuries remains second only to the number of roof fall injuries in underground coalmines. Relocation and repositioning of electrical cable, conveyor belt parts, and roof bolt sup-plies in particular are the sources of significant numbers of back injuries. To help reduce such injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are examining Mine Safety and Health Administration accident data to determine correlations between materials-handling tasks and the number of back injuries. Also being investigated are new technologies used in underground mines in the United States. Equipment is being developed or modified that would replace the necessity of doing lifting tasks manually. A Coleman manipulator was tested, and modifications were made to make it more suitable for underground mine use. To reduce or eliminate the need to manually clean off materials that commonly plug grizzly openings, a track-guided pincher arm device was developed. Oversized rock can be broken with the pincher arms in the up position, and the arms can be lowered to grab and remove debris. The arm can also be used in a sweeping action to remove cohesive fines that may bridge grizzly openings.