Search Documents

By Verne E. Hooker

Stress relief measurements were made at three underground test sites associated with the Henderson project, American Metal Climax, located in the rugged, mountainous region between Loveland Pass and Berthoud Pass on the Continental Divide in Colorado. Sufficient data were obtained to determine the three-dimensional stress ellipsoid for each site. The measurements were made at hole depths greater than one diameter of the mined opening; thus, calculated stresses are representative of premining in situ conditions. The vertical components of stress are in good agreement with overburden depth including the influence of mountain topography. Horizontal components of stress substantially increase with depth. These components are believed to be influenced by stresses presumably of tectonic origin. The largest measured principal stress was 5,900 psi at a depth of 3.708 feet. The predominant orientation of maximum principal stress for the determinations at greatest depth is in the NW-SE quadrants.

Jan 1, 1972

By R. J. SHAW

Oil shale has been defined as, "a compact, laminated rock of sedimentary origin yielding over 35 percent of ash and containing organic matter that yields oil when distilled but not appreciably when extracted with the ordinary solvents for petroleum." The oil-yielding organic matter in oil shale, commonly called kerogen, decomposes upon application of heat to form bituminous materials that are soluble in organic solvents and may be extracted from the inorganic residue. However, separation usually is accomplished by continuing the heating and thereby cracking the primary bitumens to gas and oil, which distill, leaving a carbonaceous material on the mineral residue. It has been suggested that this conversion takes place only at relatively high temperatures - 750°F or higher. On the other hand, other workers have found that transformation may take place to some extent at temperatures as low as 400°F. In either a solvent extraction or a destructive distillation process for separating organic material from the inorganic portion of oil shale, the quantity of heat required to raise the temperature of the oil shale sufficiently to induce a satisfactory rate of conversion of kerogen to oil is important in determining the design of an economical process. Likewise, the quantity of heat recoverable from a spent shale is important in determining the overall heat balance of the process. Published data on the specific heat of American oil shales are meager. Gavin and Sharp present data for two samples of Colorado oil shale, one from near DeBeque and one from Parachute Creek, and for a sample of spent shale over a temperature range of 68°F to 1940°F. McKee and Lydor present data on the specific heat of two samples of oil shale from near DeBeque, Colorado. Additional thermal data on various grades of oil shale over a wider range of temperature are needed in order to apply sound engineering practices to the design of equipment for processing oil shale.

Nov 1, 1947

By R. S. Conti

This U.S. Bureau of Mines (USBM) report discusses the results of research conducted in the USBM experimental mine at its Lake Lynn Laboratory to determine the alarm times of smoke and carbon monoxide (CO) sensors, and a point type heat sensor (PTIIS) to slowly developing coal-conveyor belt fires. The tests were conducted at air velocities of 0.44 and 0.97 m/s, The data clearly indicate that smoke sensors provide earlier warning of fire than 10 ppm CO sensors, and that 10 ppm CO sensors provide earlier warning than PTHS, A success rate of 1.0 (indicating detection of every test fire) was obtained for both smoke and C8 sensors. For the PTHS, the success rate was 0.57 at the lower air velocity, decreasing to 0 at the higher air velocity, Data are also presented showing the sequence of fire events and detection events at the two air velocities as a function of time. Results show that early detection and warning of underground mine fires will improve the probability of miners' escape.

Jan 1, 2010

By S. J. Gasior

A method for destroying the caking properties of bituminous coal was developed by the Bureau of Mines. Coal is treated in a fixed bed by heating through its plastic range under controlled temperatures in mildly oxidative atmospheres composed of inert gas and/or steam containing about 1 volume-percent oxygen. High-volatile A (hvab) and high-volatile B (hvbb) and low-volatile bituminous (lvb) coals in the size range 1/8 to 1-1/2 inches were successfully treated at 0 (atmospheric pressure) to 300 psig in static beds 6 to 18 inches deep. Conditions of treatment depended on the coal and ranged from 80 to 200 minutes at 350° to 510° C. Char produced in this manner from hvab coal was gasified with steam at 800° C and 100 psig in a fixed bed in one series of tests and in other tests was exposed to hydrogen in a dilute co current free-falling-bed system at 750° C and 3,000 psig without agglomerating.

Jan 1, 1965

By Oliver Bowles

Wire saws have been used for many years in European travertine, marble, and slate quarries. This method of sawing found very limited use in America until 1927 when it was accepted as standard equipment in elate quarries in Pennsylvania where it has been remarkably successful. Details of its operation in slate have been published in a recent bureau report.3 The very limited extent to which the wire saw has been employed in limestone and marble quarries in the United States and the seeming lack of interest even in experimental work to determine its advantages are difficult to explain in vied of its wide use in cutting similar rocks in Europe and its unquestionable advantages in sewing slate in America. In order to encourage improvement in quarry practice the United States Bureau of Mines has endeavored to obtain information as to the extent to which wire saws are used in Europe together with data on the rate and cost of sawing. The information at hand is by no means complete either in territory covered or in details of operation; it nevertheless brings out certain significant features that may be of interest and advantage to quarrymen in the United States.

Jan 1, 1931

This Part is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a corner. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency which propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1974

By P. F. Sands, Michael Sokaski, M. R. Geer

The purpose of this investigation was to determine the advantage of using either a conventional sieve bend ahead of a vibrating screen or of attaching a sieve - bend screen surface onto a vibrating screen to serve as a scalping deck when dewatering or draining dense medium from fine coal . In dewatering , use of either the sieve bend or scalping deck increased the capacity of the vibrating screen tenfold and the recovery of coal finer than 0.5 mm threefold , with no sacrifice in the moisture content of the oversize product . In dense -medium drainage , either the sieve bend or the scalping deck reduced the amount of magnetite retained on the product of the vibrating screen , particularly when the medium was as dense as that characteristic of the underflows from dense - medium cyclones . The sieve bend was slightly superior to the scalping deck in dewatering , but the scalping deck was clearly superior in dense -medium drainage . Additional advantages of the scalping deck are lower cost and a substantial saving in headroom.

Jan 1, 1963

By Raymond M. Stateham

The Bureau of Mines evaluated temperature increases on the heads of resin-grouted bolts as indicators of the integrity of the anchoring of the bolt. Expected increases were calculated by the finite difference method; the calculations were checked by bolthead temperature measurements, both in the laboratory and in the field. The accuracy of the calculations varies with the validity of assumptions necessary to the process. Measurements in the laboratory produced a temperature rise of about 4.00 F on the head of a 4-foot bolt when installed with a full column of resin. This increase remained for about 30 minutes. Similar increases were noted on bolts installed at the White Pine mine, White Pine, Mich., but bolthead temperature increases in the mine lasted only about 10 to 15 minutes. When partial columns (reduced amounts) were used, the temperature increases were smaller.

Jan 1, 1976

By Wing G. Agnew, Albert E. Long

"SUMMARY AND CONCLUSIONSTests conducted at Mount Weather indicate that clear water is the best bit coolant and cuttings-removal medium for diamond drilling. All of the mediums tested did show that drilling speed increased when drilling with the faster feed ratios (greatest pressure on the bits). In no case, how¬ever, did the increased drilling speed amount to over 16 percent, and even in a long hole the slight increase in drilling speed would be more than offset by the extra time consumed in setting up.Bit wear was excessive when lubricating agents were used, the most footage per bit was obtained when drilling with clear water in the normal manner, and the next best footage was obtained when drilling with circulated water containing no lubricating agent. The diamonds showed little or no wear in any of the bits, and all bits cut well throughout the tests. They were only taken out of service when erosion of the cast metal had progressed to the point where the diamonds were about to roll out. The lubricating agents evidently hold some of the cuttings in suspension, which in turn help to cut the rock but also wear the metal of the bit.No hard-matrix bits were tested, and it is possible that one or more of the lubricating agents might increase the efficiency of such a bit by keeping it sharp and doing away with the necessity of sharpening by sand blasting. Some tests are planned with hard-matrix-type bits and the same lubricating agents used in the tests under discussion, but it is realized that any drilling advantage gained by the bits sharpening themselves may but at least partly offset by excessive wear of the Pump parts."

Jan 1, 1945

By H. J. Heinen

This report summarizes preliminary research studies by the Bureau of Mines in electrowinning molybdenum directly from pure or impure molybdenum trioxide (MoO3) by fused-bath electrolysis in an open graphite cell without need of a protective inert atmosphere. A formulated electrolyte of the tertiary system containing 41.6 percent sodium pyrophosphate, 16.7 percent sodium tetraborat, 33.3 percent sodium chloride, and 8,4 percent molybdenum trioxide, by weight, electrolyzed at 1,000° C,, gave excellent results. Current density studies were made over a range from 20 to 260 amperes per square decimeter. Current efficiencies of 80 to 90 percent were obtained over the entire range. Yields up to 500 grams of molybdenum per kilowatt-hour were obtained. Higher current densities, however, reduced yields and produced a finer grained metal. The two most important facets in electrowinning molybdenum from MoO3, in an open cell, are temperature and electrode spacing to minimize or eliminate the formation of the suboxide MoO2, the major source of oxygen contamination. At temperatures of 1,000° C. and higher, together with the proper spacing of the electrodes, formation of oxides are practically eliminated. Molybdenum metal electrowon from pure MoO3 was 99.9 percent pure and contained 0,056 percent oxygen and 0,007 percent carbon. This metal, when arc-melted, had a Vickers hardness number of 175 and contained 50 parts per million oxygen and less than 10 parts per million carbon. Molybdenum metal electrowon directly from an impure MoO3 containing 90 percent MoO3 resulted in a metal of 99.8 percent purity.

Jan 1, 1961

By Foster Fraas

A separator for minerals of low magnetic susceptibility and fine particle size in a water suspension is described. A ring-shaped matrix of ferromagnetic fragments rotating so as to pass successively through magnetic-field and field-free regions provides for the separation. Application is illustrated in the separation of hematite and ilmenite from quartz.

Jan 1, 1966

By Rogers F. Davis

The Bureau of Mines developed a new method for the determination of oxides of nitrogen in diesel exhaust gas. The procedure, a modification of the Saltzman method, uses a NO2 absorbent for the diesel exhaust gas; the colorless absorbent becomes purple on contact with N~. When used properly this procedure gives satisfactory results in 2 hours, whereas the standard phenoldisulfonic acid method required approximately 8 hours. The new method is not satisfactory for determination of oxides of nitrogen in the overrich fuel to air ratio range.

Jan 1, 1966

By Nick Derick

The continued growth of steel production in the Western States is contingent upon the development of new iron ore sources. Recent development of economical techniques for concentrating and agglomerating taconites has focused attention on the low-grade magnetite deposits near Atlantic City, Wyo., as potentially important sources of iron ore for blast furnace smelting. Therefore, the Federal Bureau of Mines has made comparative evaluations of blast furnace burdens that incorporate pellets produced from Atlantic City concentrates. The Bureau also has evaluated the relative effect of Utah coke on blast furnace performance, using a high-quality Eastern coke as a basis for comparison. This work was done in the Bureau's experimental blast furnace at Bruceton, Pa. Tests determined the maximum wind rate that could be used while a continuous stock movement was maintained in the furnace. The furnace was operated at wind rates ranging from 800 to 1,400 std. c.f.m., them maximum limit of the blowers for the 1.75 in.-diameter tuyeres used. Using a normal Utah ore burden and Utah coke, the furnace went into a tight hanging condition with a wind rate above 950 std, c.f.m. Using the experimental pellet burden again with Utah coke, the wind rate could be increased to 1,000 std, c.f.m. and probably to 1,050 std. c.f.m, before tight hanging occurs. This represents an increase of 5 to 10 pct. in the wind rate. The experimental results indicate an accompanying increase of iron production, as much as 8 pct.

Jan 1, 1961

By J. R. Thoenen

During the year 1927 the Bureau of Mines, at the request of a number of quarry operators, undertook to make a study of quarry operating costs in order to determine average costs for certain operating conditions and to suggest a model cost accounting system for quarry operations. A detailed questionnaire was prepared and mailed by the bureau to all quarries on its records as employing ten or more men in 1926.

Jan 1, 1929

By T. Kessler

The purpose of this investigation was to evaluate the application of a spark-source mass spectrograph equipped with a spinning-electrode system for the study of various high-molecular-weight materials derived from coal. Conclusions from the investigation of anthracene, phenanthrene, chrysene, coronene, truxene, a coal-tar pitch (800 to 850 C softening point), and anthracene-chrysene synthetic mixtures follow: 1. Simplified mass spectra of anthracene, phenanthrene, chrysene, coronene, and truxene, from which the molecular weights were easily determined, were obtained by the spinning-electrode system. 2. Eight structural types having molecular weights from 178 to 252 corresponding to compounds previously observed in an electron impact mass spectrum of a coal-tar pitch sample were affirmed by this technique. 3. Mass spectra obtained from synthetic mixtures of anthracene and chrysene demonstrated that the technique is applicable for semiquantitative analysis.

Jan 1, 1967

By R. P. Vinson

The Bureau of Mines examined the effects of high humidity and water droplets on the GCA Corp. real-time aerosol monitor (RAM--l). which uses a lO4mm cyclone preseparator. Tests were conducted both in a laboratory and in a full-scale model mine entry. The laboratory tests were conducted in a test chamber saturated with moisture and water droplets. Under these extreme conditions. the RAM-I responded by indicating dust concentrations of 1-1/2 to 2 mg/m3? although the air was dust free. Within the first 2 h of each test. water accumulated in the cyclone and affected the cyclone particle separation characteristics. resulting in readings of 3 to 4 mg/m3. In addition. condensation formed inside the RAM-I case and affected the liquid crystal display (LCD). However. the full-scale mine entry tests revealed that the RAM-I can function ac-ceptably in an atmosphere of water vapor and water droplets similar to the most severe conditions found in an underground mine.

Jan 1, 1984

By Carlton E. Brown

This report contains information on the cells or containers used to hold a known small depth (usually 1 mm. or less) of the dust-containing liquid from impinger, 5/6/ filter-paper,7/ and other samples collected from the air while the particles revealed by a microscope (equipped with a 16-mm., 0.25- or 0.50-N. A. objective and ordinarily used with axial light-field illumination) are counted in order to obtain an index of the concentration of dust in the sampled air. Information is given on such subjects as the kinds of cells available, kinds used, actual depths of cells, and construction of simple, inexpensive cells. ACKNOWLEDGMENTS The interest, encouragement, and assistance received from H. H. Schrenk, chief chemist of the Health Division, in the preparation of this report are gratefully acknowledged, as 'is all other assistance received.

Jan 1, 1945

Determine the effectiveness of remining operations in reducing contaminant load (acidity, iron, and sulfate) of discharges emanating from abandoned surface and underground coal mines. Background Until the implementation of remining initiatives, most States had regulations that held the operator remining an abandoned site responsible for preexisting acid mine drainage (AMD) discharges. For example, if a mining. company wanted to remine an area hydrologically connected to an existing AMD discharge, the company became responsible, as soon as the site was activated, for treating that discharge to meet effluent standards. If the mining operation improved the quality of the discharge, but the discharge failed to meet effluent standards, the company was held accountable for perpetual treatment. Because of this regulation, most mine operators avoided abandoned sites with minable coal reserves and AMD discharges. However, changes in remining legislation allow coal companies to be released from treatment liability as long as the post-remining pollution load does not exceed the pre-remining level. If remining can improve water quality through improved mining and abatement techniques, abandoned mine land (AML) areas that previously were liabilities could become

Jan 1, 1994

Identity the difficulties of establishing vegetation on mining-related wastes resulting from adverse chemical, physical, and biological properties; describe the ecological and soil factors affecting the relationship between mycorrhizal fungi (soil microorganisms) and plants; and evaluate the feasibility of establishing vegetation on mine waste by introducing mycorrhizae. Problems in Revegetation Successfully using vegetation to stabilize a situ disturbed by mining-related activities depends on knowing the chemical, physical, and biological characteristics of the site prior to, or at the time of, stabilization. The primary objectives of mine land reclamation are to minimize environmental degradation and to facilitate the re-establishment of a functional plant-soil system. Mining disturbances can significantly alter the physical, chem¬ical, and biological characteristic of a site, thus affecting plant establishment, survival, and growth. The physical disturbance caused by the removal and replacement of soil and overburden, together with the waste material from ore processing, affect the chemical, physical, and biological process within the disturbed soil or waste. Additionally, variability in soil properties results from differences in climate, topography, vegetation, and parent material of the site.

Jan 1, 1993

By P. M. Gruzensky

A survey of the literature has been made covering the extraction of bismuth from raw materials, its separation from lead, and its subsequent refining. The use of aqueous, nonaqueous, and fused electrolytes in electrolytic refining is reviewed. This literature survey has been prepared preliminary to some proposed investigations concerning the electrometallurgy of bismuth, and, although an effort has been made to cover a majority of the applicable references, a critical review was not attempted and no assertion is made that this manuscript is exhaustive in nature. Titles of publications in parenthesis are translations from the language in which the reference was originally published.

Jan 1, 1954