Search Documents

By Kenneth Lipman

Auxiliary equipment was assembled around a purchased oscillograph to permit observation of the current and voltage characteristics of low-energy, capacitance-discharge sparks having durations of at least 10 mµ-sec. Circuit details of the assembled apparatus, performance characteristics of the complete system, and some preliminary data from representative self-initiated sparks are given in this report. INTRODUCTION One of the subjects of continuing research by the Federal Bureau of Mines Division of Explosives Technology is the ignition of explosive-gas mixtures by means of low-energy capacitance sparks. Quite early in these investigations it was recognized that understanding the gas-ignition phenomena would be facilitated by detailed information about the performance of the ignition source (spark) under the actual conditions of interest; however, the sparks of practical interest are nonrepetitive transient phenomena whose duration could reasonably be estimated to be in the time range of 1 mµsec. to 1 µsec. As such, the only feasible method of obtaining detailed information was and is oscillographic representation of the pertinent current and voltage transients. It was not until 1947 that a suitable, commercial, dual-channel oscillograph could be obtained as the basic instrument for these studies; the instrument specified in 1947 was delivered in 1950. This paper describes the auxiliary

Jan 1, 1959

By E. A. Magill

The Bureau of Mines has begun a study of the copper resources of the Cascade Mountains of Washington. The program includes reconnaissance of mineralized areas and examination and occasionally limited exploration of deposits that are considered characteristic of an area. The Bureau of Mines believes that published information may assist industry in searching for new sources of copper. The Miners Queen is one of a few Cascade Mountain deposits selected for prelim¬inary exploration. The investigation was not planned to delineate the ore body. A diamond-drilling program was carried out at the Miners Queen mine in the summer of 1955. Five diamond-drill holes were completed, totaling 628 feet. Two 35-foot shafts were dewatered, and all accessible underground and surface workings were examined.

Jan 1, 1957

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

To increase safety and productivity in mining , the potential uses and hazards of rigid foam were investigated by the Bureau of Mines Experimental Coal Mine . This research resulted in the development of chemical formulations , spraying equipment , and application procedures that permit safe and effective use of urethane foams for improving mine ventilation , for reducing weathering of mine rock and steel , for constructing seals in fire areas , and for thermal insulation .

Jan 1, 1964

By E. J. Gleim

To make a thorough survey of a coal mine in order to eliminate hazards, the competent safety engineer must be familiar with mere than one branch of engineering. It is essential that he know the properties of mine gases and the methods of detecting them, as well as hew to prevent dangerous as accumulations. It is also essential that he understand the action of overlying strata when the coal is removed, and the proper methods of protection by timbering or other suitable means of support. He must know the value of protective clothing in reducing injuries and mast be informed as to the correct handling and use of explosives to avoid premature blasts, misfires, and ether failures in blasting practice. He must understand hew to operate locomotives and cutting, loading, and various other types of machines to be able to recommend effective safeguards for protecting the men who use them in addition to being informed as 'to these and many ether activities connected with the mining of coal, he must net overlook electrical engineering if he wishes to combat the fire, shook, and ignition hazards attendant upon the use of electrical machinery and circuits in and around the mine intelligently. There are many points relating to safely in the selection, maintenance, and use of electrical circuits and equipment that are perfectly obvious to the electrical engineer but perhaps are not se evident to those not trained in this particular branch of engineering. Engineers of the U.S. Bureau of Mines who have made a special laboratory study of electricity as related to safety in minus haw e also made inspections of electrical installations at a large number of bituminous mines. These inspections have revealed practices and conditions that not only do not contribute to safety but that add nothing to efficiency and economy in the operation of the mine.

Jan 1, 1936

By R. A. Guereca

The Bureau of Mines conducted an analysis to determine criteria for steady-state, laminar flow boundary conditions for a coiled-tube gas viscosimeter by comparing experimental data from a thick-walled, stainless steel capillary in a horizontal, straight-tube condition, with similar data taken after the same capillary was formed into a helix. Overlapping volumetric f10wrates and pressure drops are covered for both configurations at pressure levels of 28, 225, and 1,000 psia at 3000 K. Friction factor, Reynolds number, and Dean number correlation plots show conditions where the coi1ed-tube flow deviates from straight-tube flow. The coiled-tube data indicate departure from Poiseui11e steady-state laminar flow at a Reynolds number close to 390 and a Dean number of about 15. Below these conditions and consistent with the data reported, Dean's circulation appears negligible. For the particular coil used, a conservative upper limit of 10 is chosen for the Dean number corresponding to an upper limit of about 250 for the Reynolds number.

Jan 1, 1967

By K. K. Kershner

To meet an increasing demand for high-purity cobalt, the Bureau of Mines has conducted investigations for producing this metal. Cobalt having a purity of 99.95 percent or higher is needed to determine heats of formation, corrosion resistances, phase diagrams, and other basic properties of the element and its compounds. This grade of cobalt may be used for preparing radioactive metal. As a result of its investigations a detailed procedure, which is of practical significance to the production of high-purity cobalt, has been developed by the Bureau for purifying cobalt solutions and for electrolytic deposition of the metal. Cobalt metal, which had a purity of 99.99 percent with reference to metallic contaminations, was deposited electrolytically. Qualitative spectrographic analysis showed only traces of calcium, copper, iron, magnesium, nickel, and zinc.

Jan 1, 1956

By J. B. Gayle

Coke-pushing difficulties have been the subject of much controversy but relatively little scientific investigation. Nevertheless, continuing pushing difficulties can greatly decrease the life of a coke oven and should therefore be considered in the selection of the blend and operating conditions used for coke production. The present Federal Bureau of Mines investigation was undertaken to correlate results of previous investigators and to supplement these results to the limited extent practical by us of an experimental slot-type oven. To this end, pushing pressures have been determined routinely for Tuscaloosa oven tests conducted during the past 10 years. Nevertheless, the accumulated information remains incomplete in many respects, and in view of the recognized inadequacies of the data, publication is now undertaken only because of the scarcity of published information on this important problem and the discontinuation of carbonization studies with this oven.

Jan 1, 1961

By A. T. Coumbe

During 1953-55, 31,105 miles of pipe for transporting crude petroleum and refined products was laid in the United States, a total slightly below that of the prior 3-year period, according to data compiled by the Bureau of Mines, United States Department of the Interior. The added mileage consisted of 22,571 miles of new pipe, representing about 2,163,807 tons of steel, plus 8,534 miles of secondhand pipe, equivalent to about 419,849 additional tons of steel. During the 3-year period, 13,069 miles of pipe was taken up. By January 1, 1956, the Nation had 188,540 miles of pipeline, an 11-percent gain over the 1952 total of 170,504 miles. The greater use of larger diameter pipelines indicated in recent surveys has continued, as the mileage for sizes 12 inches and over increased from 13 percent of the total mileage at the close of 1952 to 16 percent 3 years later. Crude-oil trunklines 12 inches and over in diameter gained 24 percent during 1953-55, and these larger lines represented 30 percent of the total mileage compared with 25 percent at the close of 1952. Furthermore, the mileage for crude-oil lines less than 12 inches in diameter declined 2 percent and made up only 70 percent of the 1955 total against 75 percent n the previous survey. Product Lines 8 inches and over increased 43 percent from 1952 through 1955 and composed 70 percent of the total mileage compared with 66 percent in 1952.

Jan 1, 1956

By R. V. Ramani, P. M. T. White, D. Sutton

1.1 General The examination and evaluation of a mineral deposit to determine whether or not it can be profitably exploited entails many factors unrelated to the physical nature and intrinsic worth of that deposit. Nevertheless, geology and geologically related factors have great bearing on the economic potential of the deposit. This is only natural because the deposit owes its existence to these factors. This is even more so in underground mines where the whole system is a geologically enclosed one. Geology plays a major role in at least four phases of a mineral venture. Firstly, it acts as an indicator of the existence of parti¬cular minerals. For example, it is inconceivable that a sedimentary coal deposit would exist in a granitic batholith or stock, or that a sandstone would host primary copper or nickel sulphides. Further, the positional relationship of different rock types may be significant in locating deposits such as replacement zinc and copper sulphides in limestones which have been intruded by igneous rocks. Thus, geology is important in the exploration phase of a mineral deposit. Secondly, once potentially valuable minerals have been discovered, knowledge of geology plays a significant role in determining the dis¬tribution, grade and extent of the mineralization. Controls on mineralization include one or all of those related to structure, rock type, sedimentary features, post-depositional redistribution, etc. Con¬sequently, in order to effectively evaluate a deposit in terms of

Jan 1, 1974

By J. E. Gebhardt

External control of the electrochemical potential of a bed of mineral particles has been investigated by the Bureau of Mines as a method for controlling particle inter-action with organic collectors and thus, flotation response. A cylindrically shaped, 200-to 300-g bed of sulfide mineral particles was used as the working electrode to examine the potential distribution in the bed. The dissolved oxygen concentration of the electrolyte had a significant effect on the potential profile across the mineral bed. Low oxygen levels were necessary to achieve uniform electrochemical potential distributions. Flotation separation of a chalcocite-pyrite mineral mixture by controlled potential was achieved using ethylxanthate, but the flotation behavior of chalcocite and pyrite from the mixture does not follow the flotation behavior of the individual minerals. That is, the presence of another sulfide mineral alters the flotation behavior with ethylxan-thate. Galvanic interaction due to mineral-to-mineral contact between chalcocite and pyrite contributes to differences in the recovery. Chalcocite dissolution products had a deleterious effect on pyrite flotation by activating flotation below -0.1 V (saturated calomel electrode) and depressing flotation above -0.1 V. Pyrite dissolution products had no effect on chalcocite flotation.

Jan 1, 1985

By Alton B. Cook

Equipment has been designed and fabricated for study of the vaporization of oil during gas-cycling operations, A sand-packed steel tube, which can be rotated to minimize gravity drainage, is used as a model oil reservoir. A minute windowed cell at the discharge end of the tube through which the liquid-gas interface may be observed, makes possible the separate removal of produced free gas and gas-saturated oil. The operation of the model oil reservoir, and auxiliary equipment, are described by use of a schmatic flow diagram. Details of the specially designed equipment are illustrated by isometric and pictorial drawings, and a description of the experimental procedure is given.

Jan 1, 1959

By G. H. Cobb, J. L. Johnson, H. H. Heady

An infrared absorbance technique is described for analyzing anodic gases produced during the electrowinning of uranium , thorium , and rare - earth metals in molten fluorides . Typical components determined qualitatively in a gas sample are CO , CO₂ , CF4 , C₂ Fe , C3F8 , COS , CS₂ , and SiF4 . About 20 minutes are required to record and interpret the spectrogram , and report quantitative results for CO, CO₂ , CF4 , and SiF . The procedure is used for control during electrolysis .

Jan 1, 1964

By Philip C. Tully

This Bureau of Mines report contains experimentally determined vapor-liquid equilibria data for a helium-nitrogen-methane mixture with a nominal composition of 15, 60, and 25 mole-percent, respectively. Measurements of the equilibrium phase compositions were obtained by means of a windowed cell, in conjunction with an automated chromatograph and a special analyzer for low helium concentrations. The data presented include a comprehensive table and eight graphs depicting phase compositions, vaporization ratios, and correlations with a previous study of two helium-nitrogen-methane mixtures of different compositions.

Jan 1, 1976

By M. M. Tilman

The Bureau of Mines conducted research to determine whether it is possible to substantially improve the fatigue resistance of lead sheet by means of surface coatings. Five types of coatings were applied to unalloyed chemical lead sheet. Flexural tests revealed that the best fatigue resistance was obtained with coatings of vacuum grease. Vacuum-grease coatings on unalloyed lead sheet resulted in fatigue resistance at least as good as that of the fatigue-resistant alloy Pb-0.04 Ca. Coated lead sheet was also tested in short-time tensile tests and in tensile creep tests. Tensile and yield strengths were increased by several of the coatings with only moderate loss of ductility. Creep resistance was also improved in varying degrees by most of the coatings. The Bureau also conducted research on the effectiveness of noise barriers by using sheet lead in combination with other materials. Noise barriers consisting of continuous-cast sheet lead with gypsum board were found to be effective and relatively inexpensive barriers.

Jan 1, 1978

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By James R. McVey

Tests during pillar robbing, longwall operations, and other mining activities indicate that roof-floor convergence rates can be used as an indicator of imminent roof failure. A large number of electrical-mechanical devices have been built to measure convergence as well as convergence rates, but most obstruct mine traffic and are costly and time consuming to install. The Bureau of Mines has designed and is evaluating three types of small ultrasonic units to make these measurements. The new instruments provide nonobstructing measurements up to 35 ft away. The ultrasonic transducers can be attached to a roof bolt, placed in an unsupported area (by means of a toss basket), or handheld. Total distance to the target and rate of closure are displayed digitally to 0.001 ft and 0.01 ft/min, respectively.

Jan 1, 1984

By Foster Fraas

This Bureau of Mines report describes a method for separating minerals at magnetic susceptibilities within the diamagnetic susceptibility range. The maximum feed rate varies directly with the square root of the lower limit of permissible susceptibility, while the lower limit of permissible susceptibility varies inversely as the square of the magnetic field strength. Minerals may be separated at particle sizes smaller than possible on conventional dry-type magnetic separators.

Jan 1, 1969

By P. R. Bremner

The United States is more than 90 pct dependent on imported bauxite a source for aluminum, but it has vast nonbauxitic aluminum resources, such as kaolinite, anorthosite, alunite, etc. As part of a program to devise processes for treating these resources, the Bureau of Mines investigated a bench-scale leaching process using hydrochloric acid (HC1) and fluoride to extract aluminum from Wyoming anorthosite. HC1 and fluoride-to-aluminum (F/Al) mole ratios were studied with respect to aluminum extraction for single-stage, cocurrent, and countercurrent leaching modes. Using 95 pct stoichiometric HC1 and a F/Al mole ratio of 0.27, 90 pct of the aluminum was extracted by countercurrent leaching. Single-stage leaching with the same amount of acid and fluoride extracted 48 pct of the aluminum. Three fluoride sources, CaF2, Na2SiF6, and H2SiF6, were used and gave similar results on aluminum extractions.

Jan 1, 1982

By Oliver Bowles

"Introduction.During recent months the Bureau of Mines has conducted a detailed study of the slate industry with special reference to increased efficiency in its production, preparation and utilization. The results of these investigations will be incorporated in a forthcoming bulletin. The purpose of this preliminary paper is three-fold. One object is to bring to the attention of slate producers certain modifications in manufacture and classification which would encourage a wider use of slate. A second purpose is to direct the thought of roofers toward the importance of proper laying of slate, and the third object is to acquaint the general public with its enduring qualities.Origin and character.Without entering into any detailed discussion of the origin and history of slate, a subject to be covered in the bulletin mentioned, it may be of interest to the general reader to know that slate is originally formed from mud or soft clay, carried down by streams and laid down in successive layers in deep water. The pressure of superimposed materials gradually compresses the clay into a firm rock known as shale. In many places this shale was, during the succeeding ages, subjected to intense pressure and folding due to mountain-building forces within the earth. This intense pressure, together with high temperature, changed the clay into other minerals such as mica, chlorite, and silica, which are very resistant to weathering, and also developed a very definite cleavage or splitting direction which characterizes the rock as slate. It is this property which renders slate of value for roofing, for, by using a broad chisel and a wooden mallet, a slate worker can readily split it into thin sheets which are later trimmed into rectangles of various sizes."

Jul 1, 1921

By G. W. Reimers

Exothermic oxidation reactions of sulfide minerals can produce self-heating situations in underground mines. If the self-heating is unchecked and the resulting heat is not sufficiently dissipated, the result can be spontaneous combustion fires. This U.S. Bureau of Mines report describes laboratory tests conducted to measure the reactivity of pyrite following treatment with additives to counter its self-heating tendencies. Thermal gravimetric analysis (TGA) and isothermal oxidation procedures were used to obtain information on pyrite ignition and the behavior of pyrite during low-temperature oxidation to ferrous sulfate. The determination of treatment effectiveness was evaluated by adding 5 wt pct of the compound to the pyrite before milling. The resulting samples were then heated in moistened air and after 24 h, the amount of pyrite oxidation determined. Results of these tests indicated that several phosphate compounds reduced the oxidation of pyrite to sulfate to about 50 pct or less compared with the oxidation of untreated sample at 200° C. Cupric sulfate reduced oxidation to about 20 pet untreated sample at 200° C. Sodium, calcium, and potassium chloride reduced pyrite oxidation to levels of approximately 15 pct or less of the untreated sample. Using only 1 pct of sodium or calcium chloride was effective in slowing pyrite oxidation to less than 20 pct of the untreated sample.

Jan 1, 2010