Search Documents

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method's usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987

By H. B. Humphrey

The solvents used most widely in industry may be divided into groups according to their chemical and toxicological properties. These groups, with representative members, follow: Petroleum distillates (aliphatic hydrocarbons) Examples: Gasoline, benzine, Stoddard's specification solvents. Alcohols, esters, ketones, ethers, and ether alcohols Examples: Denatured alcohol (ethyl alcohol to which various denaturants may be added), methanol (methyl alcohol), ethyl acetate, amyl acetate (banana oil), acetone.

Jan 1, 1956

By Ivan L. Nichols

Tailings dumps at Mercur, Utah, contain about $7 million worth of gold in 3.5 million tons of mill tailings assaying about 0.07 ounce of gold per ton. Commercial mining and milling at Mercur ceased in 1942. To determine whether improved technology was now available that might permit economic reprocessing of the Mercur dumps, the Bureau of Mines probed for a low-cost method that would be applicable to these tailings. A composite sample prepared for laboratory studies assayed 0.062 ounce gold per ton. About 10 percent of the gold occurred as a water-soluble cyanide. Conventional cyanide leaching dissolved 32 percent of the gold, and hot, strong cyanide solution dissolved 42 percent. Results were not improved by pretreatment with acids, bases, or oxidants. After expensive preroasting, gold recovery by cyanidation was increased to 65 percent. The simple procedures were ineffective, and more effective procedures were too costly for economical processing of Mercur tailings.

Jan 1, 1970

By John E. Kelley

The Bureau of Mines conducted a study to determine the feasibility of joining refractory metal compounds to each other and to oxide ceramics by a vacuum hot press-diffusion bonding method. Very satisfactory joins were made of ZrC to ZrB2, ZrN to ZrB2, ZrC to ZrN, and of ZrC, ZrN, and ZrB2 to Al203. Each of these join assemblies contained a mixture layer comprising 50 weight-percent each of the two end compounds. The mixture layer, sandwiched between each end compound, enhanced bonding and smoothed out the thermal expansion gradient between the two end members. Strength and thermal shock tests showed that the join areas of the ZrC, ZrN, and ZrB2 joins were stronger and more shock resistant than the parent materials. Also included in the joining tests was one each of TiC to TiB2, TiC to TiN, TiB2 to TIN, and TiC to ZrB2 joins. Each of these was well bonded, showing that the vacuum-hot-press method can be used for a variety of systems.

Jan 1, 1969

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines (USBM) and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CPR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 2010

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 2010

By L. Y. Sadler

The Bureau of Mines conducted a study Lo determine the loss in weight of silica (Si02) volatilization from low-alumina (A1203) refractories used as hot face liner materials in such process equipment as coal gasifiers, synthesis gas transfer lines, and ammonia plant secondary re-formers. Small specimens of 80-and 40-pct-A1203 brick and 95-pct-SiO2 brick were exposed to steam in high-pressure furnaces at pressures of up to 1,000 psig and temperatures up to 1,400° C for periods ranging up to 120 h. Weight losses from the 40-pct-A1203 brick after 40 h of exposure were highest, 2.75 pet at 1,400° C and 1,000 psig. The rate of weight loss had dropped to near zero after 80 h of exposure at all temperatures. No relationship between total silica content of the specimen and weight loss could be established nor did scanning electron microscopic examination of the specimens before and after exposure identify specific regions (e.g., surface) suffering a disproportionate share of the silica loss. It was concluded that minor silica volatilization is likely to occur, if at all, at temperatures of less than 1,000° C and pressures below 1,000 psig, and that low-alumina refractories should be used as dry-ash coal gasifier hot face linings.

Jan 1, 1986

By E. C. Lane

The motor gasoline that is being marketed in the United States this summer is slightly more volatile than that sold a year ago. The increase in volatility is shown by a lowering of the distillation temperatures, ranging from 2°F. at the average initial boiling point to 4°F. at the average end point. During the past nine years the Bureau of Mines has made semiannual surveys of the gasoline marketed in the United States, the survey just completed being the eighteenth in the series. The cities in which samples were collected have been chosen as representative of the more important marketing territories, as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country. Samples were collected in Omaha as well as in the 11 cities where samples were taken last winter. It was believed advisable to include samples from Omaha in order to give a better balance to the survey for the country as a whole.

Jan 1, 1928

By Charles L. Harness

Fifty years ago, the belief that "fillers" were added to paints for the sole purpose of diluting and cheapening the pigment may have been justified; but paint technology has made tremendous progress since that time, and today both the manufacturer and the consumer know that the judicious use of fillers may add desirable properties to a paint that cannot be introduced in any other way. A growing respect for these accessory materials has led to the use of the more euphemistic term "extender." The names "extender" and "filler" are to a considerable degree synonymous. The newer term, "extender," is adopted in this paper, though it is actually no more descriptive than the older name. Stewart's3/ definition of extender is: "A cheap pigment, usually of an inert type, used to extend or increase the bulk of a paint, thus reducing its unit cost. Extenders are also used to adjust the consistency of a paint and to let down colored pigments of great tinting strength. The use of an extender in a paint does not necessarily mean the resultant product will be inferior. In fact, extenders sometimes, improve -certain characteristics of a film." All extenders are not cheap, as, for example, wet-ground mica and diatomite. Research in the, use of extenders (also sometimes called "inerts") has been one of the host active branches of study in the paint field; and many thousands of dollars have been spent in establishing the physical and chemical characteristics required of various natural mineral extenders for numerous paint formulas

Jan 1, 1943

By E. M. SEELEY, F. S. LOTT

Expansion in total capacity of the natural-gasoline industry.to produce light products continued in 1944 and 1945. The average rate of gain, however, was reduced to about 6 percent annually from over 9 percent in the preceding 4-year period. New facilities at cycle plants again accounted for most of the increase in productive capacity. Between January 1, 1944, and January 1, 1946, the number of cycle plants increased from 32 to 37 and their total capacity from 3,278 thousand gallons daily to 4,848 thousand (48 percent). Capacity of all other plants in the industry increased in the same period from 12,735 thousand gallons daily to 13,080 thousand, or only 3 percent. The capacity of the average plant increased to 28,600 gallons a day from 24,400 gallons on January 1, 1944, continuing the established trend. The average capacity of cycle plants increased to 131,000 gallons a day from 102,400 gallons, and the average capacity of all other natural-gasoline plants increased to 22,200 gallons a day from 20,400 gallons. Although the number of plants increased in only three States in the 2-year period (Texas, Okla- homa, and Arkansas), the total capacity of plants increased in eight States. A further decline of 29 reduced the total number of plants to 626 on January 1, 1946. Compared with 10 years earlier, gasoline plants were more numerous in only 4 States: Texas (48 more), New Mexico (7 more), Arkansas (2 more), and Louisiana (1 more). The largest declines, in order, were in Oklahoma, Illinois, Pennsylvania, West Virginia, and California. The number of plants with fractionating equipment for separating the liquefied gases from heavier fractions was 202 on January 1, 1946 and 182 2 years earlier. The principal changes in number and capacity of shut-down plants were an increase in Texas and a decrease in California. Shut-down natural-gaso- line plants are usually among the smallest units in their vicinity.

Apr 1, 1947

By K. K. Kelley, W. W. Weller

This report contains experimentally determined heat capacity data for four crystalline sulfides -- AsS , GeS , NiS , and Ni3 S₂ -- over the temperature range from 50 ° to 298.15 ° K. The heat capacity data were used to evaluate the entropies of the sulfides at 298.15 ° K. Entropies of formation from the metals and rhombic sulfur and from the metals and diatomic sulfur gas are also included .

Jan 1, 1964

By Edward L. Burwell

The Bureau of Mines investigated the use of dilute polymer in brine solutions to increase the efficiency of air in gas flooding model oil reservoirs. Slugs (0.23 pore volume) of 500 ppm polyacrylamide were injected into a model, consisting of a high- and a low-permeability core, that had been previously gas flooded to residual oil. Gas flooding was then resumed. Of the total gas volume injected, the percentage entering the high-permeability zone was greatly reduced after polymer injection but remained unchanged when slugs of water without polymer were used.

Jan 1, 1970

By Bruce I. Thomas

The Fairbanks mining district forms an arc 40 miles long and 8 miles wide on the north side of the Tanana Valley in central Alaska. This is a region of broad valleys and rounded hills that range in elevation from 600 to 2,600 feet Lode-gold production started in 1910 and has continued sporadically to the present, but the largest single mine produced only 40 tons per 24-hour day. Total recorded lode-gold production of the district is 241,000 fine troy ounces of gold from ore that averaged 1.32 fine ounces per ton. The ore was mined chiefly from narrow veins and veinlets alined along anticlinal folds at Ester Dome and the Pedro Dome-Cleary area. The only proven reserves are reported to be at the Ryan Lode at Ester Dome and at the Keystone Mines, Inc., holdings in the Pedro Dome-Cleary area. An inferred lode-gold resource for the district of approximately 4,000,000 ounces is considered to indicate only the order of magnitude of the lode-gold potential because of the absence of detailed data needed to evaluate the numerous deposits.

Jan 1, 1973

By William H. King

The Fannie Ryan deposit is situated about 9 miles northwest of Boulder City, Clark County, Nev. at an altitude of about 2,000 feet on the north side of the River Mountains. The deposit is covered by several unpatented claims owned by Fannie B. Gulick of Las Vegas, Nev. The Boulder City deposit is within the Hoover Dan National Recreational Area. It is situated about 3 miles southeast of Boulder City in sec. 23,T. 23 S., R. 64 E., Clark County, Nev. The Deposit was covered by several unpatented mining claims owned by S. R. Whitehead of Las Vegas. The deposits occur in sedimentary beds of the Muddy Creek formation that overlie older volcanic extrusive. The manganese minerals occur as soft oxides of the wad type. The exploration was conducted by the Bureau of Nines in cooperation with the Federal Geological Survey and comprised a study of the geology, mapping of the areas, and development by shaft sinking; diamond drilling, and sampling. On the Fannie Ryan Gulick property the work consisted of cleaning and sampling seven old trenches on the outcrop and diamond drilling seven holes totaling 1,482 foot. At the Boulder City deposit 188 feet of drilling was done in two holes. A 4- by 6-foot shaft was sunk to a depth of 44.5 feet, and the north and south sides of the shaft were sampled.

Jan 1, 1950

By L. B. Berger

This information circular is a revision of I.C. 7238, Danger from Carbon Monoxide in the Home, by L. B. Berger and H. H. Schrenk, issued in April 1943. Each winter brings its toll of deaths and serious accidents from the deadly gas, carbon monoxide. Newspapers carry warnings to the public of the, dangers of this gas, and frequent news items report the finding of persons dead at unconscious from the effects of carbon monoxide, yet these accidents continue. Either these warnings are not read, or they are unheeded by people who feel that, "It can't happen to me." It can happen to you carbon monoxide is no respecter of persons.

Jan 1, 1954

By M. J. Kovalik, D. E. Wolfson, F. Fischler

Plastometric tests were made to determine the maximum thickness of the plastic layer for different U.S. coals . The effect of test variables on the maximum thickness of the plastic layer was studied . The values for the maximum thickness of the plastic layer were found to be related to the Gieseler maximum fluidity , plastic temperature range , free swelling index , and other plastic properties of coals . Only a general relationship was observed between the plastometric parameters obtained in these tests and the coking properties of coal .

Jan 1, 1964

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and, liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise eight be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and. removing the disintegrated clay particles from wells after the perforated pipes have been inserted. Mechanical methods for removing mud sheaths are quite satisfactory, but prompted by tie request of certain operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions.

Jan 1, 1934

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise might be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and removing the disintegrated clay particles from wells after the perforated Wipes have been inserted. Mechanical methods for removing mud sheaths are :quite satisfactory, but prompted by the request of certain .operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions. This report describes the laboratory work and deals generally with a chemical method for removing the mud sheath, cake, or plaster deposited against the face of oil sands in drilling wells end in wells that, on being shut in temporarily during periods of overproduction of oil, are conditioned for the shutdown .period by filling the well opposite the producing formations with mud fluid. The method described in this report was devised in the San Francisco laboratory of the Bureau of Mines and, as far as the writers have been able to determine, differs from any chemical method ever used in actual wells. The method proposes to add a small amount of calcium carbonate (preferably pulverized limestone) to the mud fluids before they are introduced into the wells so that the resultant mud sheaths will be susceptible to disintegration by acid solutions when it is desired to expose the faces of the oil sands in the wells.

Jan 1, 1934

By Eric R. Bauer

This Bureau of Mines publication describes and illustrates the physical signs of excessive loading on mine roof supports, installations, and openings. It is designed to assist mine personnel in recognizing potentially hazardous ground conditions, by emphasizing the preliminary effects of developing unstable ground. Increased worker awareness can be expected to reduce the injuries and fatalities resulting from falls of roof, rib, and face.

Jan 1, 1985

By Ludwig Schmidt

The policy of buying crude oil on a gravity basis , recently instituted by the major crude oil purchasing agencies in the Mid- Continent field , has caused a new and vital interest to be taken in the work of the U. S. Bureau of Mines for preventing evaporation of crude . From the early years of the industry oil men have recognized that the gravity of crude oil is usually an index of the gasoline content , but it has not been so generally known that the gravity of the crude oil decreases if evaporation is permitted . In 1919 the Bureau of Mines began a survey to determine the evaporation losses of crude petroleum in its various stages of handling from the well to the refinery , The results of this study are presented in Bulletin 200 ( Wiggins , J.H. , Evaporation losses of petroleum in the Mid- Continent Field , Bulletin 200 , U. s . Bureau of Mines , 1922. ) and Bulletin 225 ( Wiggins , J.H. , Methods of decreasing evaporation losses of petroleum , Bulletin 225 , U. S. Bureau of Mines , ( In press ) The findings of this survey were so startling that soon after the preliminary report had been published , several tank companies began manufacturing vapor- tight tanks for the purpose of reducing these important losses . Since that time the development of this type of apparatus has been so rapid that today , every oil trade journal carries numerous advertisements of vapor- tight tanks and equipment as well as technical articles dealing with various problems in connection with the elimination of evaporation losses , whereas three or four years ago the subject was scarcely even thought of. The present report has been prepared in response to numerous requests for information on the apparatus actually being used to prevent evaporation losses . At this time oil operators are also extremely interested in holding the lighter fractions in the crude oil in order to prevent a lowering in gravity . The practice of removing the vapors from crude- oil tanks by means of a slight vacuum and extracting the gasoline from them is not discussed here .

Feb 1, 1923