Search Documents

By David C. Oyler

Three long horizontal holes were drilled from a directionally drilled surface hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diameter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a vertical depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 ill (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

By W. P. Huleatt, R. B. McCulloch

"The Big Four zinc-deposit, directly above the north bank of the Green Mountain Reservoir on the Blue River, Summit County, Cole., was discovered in 1937 by the present owner, Walter McDaniel, who lives on the property. Mr. McDaniel, together with members of his family, have worked the mine on a small scale since its beginning and have shipped quantities of sorted high-grade ore to the International Smelting Co. at Tooele, Utah, and the Combined Metals Corp. at Bauer, Utah. More recently, parts of the nine have been operated by lessees.The property had been examined previously by the Federal Geological Survey, and the geological report was made available' to the Bureau of Mines.The Big Four mining claim was located in 1937 by Walter McDaniel and his wife Frances,- who had been prospecting in the vicinity since 1933. The discovery of the high-grade zinc deposit caused considerable excitement, as it had not been regarded as a mineralized area.Mining was begun in 1937 and carried on until 1944 by Mr. and Mrs. McDaniel with the help of a few hired miners. During 1944, parts of the mine were leased: to various parties Who produced small quantities of ore but did no development work.Shipments during 1941 .totaled 752 tons; during 1942, 387 tons; and during 1943, 510 tons. From the beginning of 1944 to April of that year, 98 tons wore produced and shipped to Utah,Since the lessees began operations, a grade of 30 to 35 percent zinc has been maintained by careful sorting. No production has been recorded for 1945.The Big Four mine is situated on Colorado State- Highway 9 between Dillon and Kremmling on the south face of Green Mountain overlooking the Green Mountain Reservoir, a Federal irrigation project on the Hue River, Green Mountain rises 1,600 feet above the general level of the valley to an altitude of 9,408 feet and the surrounding terrain, i s correspondingly mountainous and rugged."

Apr 1, 1946

By Earl W. Waay

"Since the beginning of the petroleum industry in 1839, up to within two or three years ago, these has been a dearch of engineers who have had the fundamental technical training also sufficient practical experience so that they could compete with practical men. Need for Technical Investigations in Industry: As in the early stages of the mining industry, the petroleum industry has been rather slow in realizing the need for technical assistance and investigators in the development and production of oil lands. The rapid increase in consumption, however, during the past few years has accentuated this need more than anything else could have done. When it is realized that our production cannot longer keep pace with the demand, it is easily understood why it is imperative that be instituted which will tend to conserve and prolong the supply of oil from the fields now known. It is interesting to note from preliminary production figure given cut by the U. S. Geological Survey, for the year 1919, that the United States produced about 430,000,000 barrels, an increase of 22,000,000 or 6 per cent over 1918 production and also there was imported, chiefly from Mexico, a little over 52,000,000 barrels, making a total of 430,000,000 barrels, to satisfy the trade demand in the United States of which almost 6,000,000 barrels was exported. Stocks were not materially increased.Other significant facts regarding our petroleum industry, are that just recently the U. S. Shipping Board in soliciting bids for 24,000,000 barrels of fad oil to meet prospective needs, received bids for only 1,500,000 barrels at prizes ranging from 75 to 90 per cent higher than was paid last year. One large company on the Pacific Coast has stopped its export trade, and has notified consumers,of gas-engine distillate that they will no longer make deliveries of this product. This will materially affect the farmer, in many instances, through his use of the truck and tractor."

Apr 1, 1920

By Gary P. Sames

Shale roof deterioration in coal mines. caused by ventilation air humidity fluctuations, is a common ground control problem. Shale roof deterioration often results in increased accidents, decreased production, inadequate ventilation, and increasing operating costs in maintaining haulage roads and airways. The results of Bureau of Mines research indicate that air tempering entries are an effective method of controlling deterioration prone shales. Some of the conclusions and recommendations drawn from Bureau research include (1) moisture sensitive shales will react adversely to moisture gains and losses, (2) the majority effect of specific humidity fluctuations can be concentrated in and absorbed by tempering entries, (3) tempering entry panels should be located as near to the main intake as possible, (4) tempering panels should be designed for a conservative recovery and provide a minimum of 20-to 30-min air residence time, (5) ventilation and escapeway requirements must be considered early in panel design, and (6) an efficient support and sealant plan can increase the life expectancy of a tempering panel.

Jan 1, 1985

By Andrew D. O. O’Brien, Linda J. McWilliams, Joe L. Howell, Douglas E. Pollock, Jeanne A. Zimmer, Andrew B. Cecala

A quick, safe, and effective method has been developed that allows workers to clean their dust laden work clothing periodically throughout the day. For the mining industry, this technique is much more effective than the current federally approved method of using a vacuuming system. This newly designed method is relatively inexpensive and can be easily installed at any operation to allow workers to clean their clothing without contaminating the worker, the work environment. or co-workers to elevated respirable dust levels. This clothes cleaning process uses an air spray manifold to blow dust from a worker's clothing in an enclosed booth, which combines the dust for capture and removal by a baghouse dust collector. Since the air exhausted by the dust collector causes the booth to be under negative pressure. no measurable quantities of dust were ever measure escaping from the booth to contaminate the work environment and/or other workers. The worker performing the cleaning process is required to wear a half-mask fit- tested respirator with an N 100 filter, hearing protection, and full seal goggles. Dust samples taken inside the respirator of test personnel performing the clothes cleaning process showed very minimal to no respirable dust. This clothes cleaning process was performed in less than 20 seconds and was significantly y cleaner than either the Federally approved method of vacuuming, or the most common method or using a single compressed air hose. It was also determined during this research that polyester-cotton blend coveralls clean more effectively than coveralls which are 100 percent cotton. The newly designed clothes cleaning process has potential application to any industry where workers' clothing becomes contaminated with most any type of dust or product.

By F. H. Nehl

Ion elutriation was used to extract silver cyanide complexes and free cyanide from aqueous streams containing up to 10 ppm silver and 5 ppm free cyanide. Screening tests selected nine of 350 different surfactants for further, larger scale experiments. The screening procedure used 0.1 g of each of the surfactants in 300 mL of synthetic wastewater. Air was sparged into the test cell at 50 cc/min. The foam was refluxed during the tests and was not sampled. Samples of the solution were taken at specified intervals and analyzed by wet chemical methods for free cyanide and by atomic absorption for silver content. The most effective surfactants lowered the silver and free cyanide concentrations to less than 0.5 ppm in 1 h or less. These surfactants were quaternary amine salts with one long chain (C12-C18) organic group and three methyl groups. Experiments using 3 L batches of wastewater or an ion elutriation cell continuously fed with solution draining from an inactive heap leach operation confirmed the results from the screening tests.

Jan 1, 2010

By J. A. Kost

Contract H0242013 was originally to evaluate through underground tests, water spray systems for controlling respirable dust at the face of a longwall plow. A number of difficulties were encountered which made such an evaluation impractical. The contract was modified to evaluate, in the BCR dust tunnel facility, the live factors believed to affect respirable dust levels. A 60-foot long; plow face mock-up was constructed in the dust tunnel, a facility with controlled airflow and dust concentration. Six types of nozzles were tested with the following parameters: two nozzle orientations, two levels of water pressure, two levels of airflow, and with and without simulated airflow through the gob. Of these factors, the most significant in reducing respirable dust levels was nozzle orientation, where the nozzle directed 45 degrees downstream resulted in 27 percent lower dust levels than those directed 45 degrees upstream (against the airflow). Following in order of effectiveness were the higher water pressure and the lower airflow. All nozzles tested resulted in similar dust reduction, i.e., the type of nozzle was the least significant factor.

Jan 1, 1979

By B. S. Covino

The Bureau of Mines, U.S. Department of the Interior, is conducting research to devise substitute corrosion-resistant materials by using ion implantation to form alloyed regions near the surfaces of metals. These alloys were prepared by implanting 25-kev Cr+ and/or Ni+ ions into iron. Their resistance to corrosive attack was evaluated by determining their anodic polarization behavior under potentiodynamic conditions in a solution containing sodium chloride, boric acid, and sodium borate. These electrochemical studies have shown that the general corrosion resistance of ion-implanted alloys was comparable to nominally equivalent bulk alloys. The pitting-corrosion resistance of the ion-implanted alloys was superior to that of iron, although not as good as that of most of the bulk alloys tested.

Jan 1, 1980

By Raymond B. Ladoo

Talc mining ·in the state of New York was first started about 1876, but important production did not start until 1880, when about 4,000 tons were shipped, In 1883 the production was about 6,000 tons valued at $75,000, or an average of $12.50 per ton, From this date the production gradually inc~eased to a peak of 93,236 tons in 1916, valued at $961,510 or about $10,30 per ton, In 1918 the production declined to 71,167 tons valued at $902,100, or about $12,70 per ton. For ma.ey years New York ,-Jas the largest producer in the United states, but in 1917 and 1918 its output was surpassed by Vennont in tonnage thou[;h not in value. In June, 1920, there were three companies producing talc in the Gouverneur district, st. La,1Tence Co'Ul'lty, and one near Natural Bridge.

Oct 1, 1920

By N. C. Tomoeda, W. D. Bensema, J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 350 meters (1150 ft .) and 488 meters (1600 ft .) . The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broad- band, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or E layers of ionosphere as an upper plane and the earth as a lower plane. The measurement systems used are similar to those used earlier. The technique is to record broadband, analog signals, digitize the data, and use a fast- Fourier transform to obtain spectral plots. This tech- nique is novel in that it can measure simultaneously all magnetic field energy within a limited portion of the spectrum for a limited time, and, after processing, reproduce the events occurring in that time interval in great detail .

Jan 6, 1974

By William J. Campbell

The Federal Bureau of Mines provided five test materials--amosite, short-and long-fiber chrysotile, crocidolite, and nonfibrous tremo1ite--to the National Institute of Environmental Health Sciences (NIEHS) for studies on the biological effects of orally ingested asbestos-related materials. An inter-agency agreement between the Bureau and NIEHS made possible this program to characterize these test materials. The Bureau in turn received support through contracts with the Ontario Research Foundation for the milling of amosite and crocidolite, and with the University of Maryland for microscopic measurements. The five test materials, which were supplied in quantities of 960 to 1,200 pounds each, were characterized by chemical-instrumental analysis for elemental composition, surface area, density, X-ray diffraction, infrared spectroscopy, thermogravimetric analysis, mineralogy, and particle size analyses. Particle size distributions were emphasized because of the current theories relating adverse biological effects to length-width characteristics of durable elongated particles.

Jan 1, 1980

By Raymond B. Ladoo

"Domestic Situation:The greatly increased use of lithopone as a base for paints, particularly for interior use, has timulated the demand for barytes to such a degree that the supply cannot keep pace with the demand. Lithopone is an artificially prepared compound composed of about 70 per cent barium sulphate and 30 per cent zinc sulphide, precipitated together. Its most important use is in paint, but it is also used in oilcloth, linoleum, rubber goods, shade cloth, etc.Prior to the war large quantities of barytes were imported from Germany, but during the war imports were negligible, domestic production increased very greatly and is still increasing. Ground barytes as used in paints/ formerly regarded as an adulterant, but now it is generally recognized as a valuable paint constituent. Mile domestic sources have expanded rapidly they have not overtaken the demand and there is need for still greater expansion. Stocks are low, little is being sold on the open market, and prices are high. Since barytes is a gangue mineral associated with metallic ores now being mined in the west, it is suggested that more attention be given to its recovery as a by-product.The following tables compiled from reports of the U.S. Geological Survey and the Bureau of Foreign and Domestic Commerce, indicate the growth of domestic consumption."

Jan 1, 1920

By Robert W. Gordon

This report describes the results and conclusions of the further development of a lightweight probe drill for use in anthracite mines. Improvements to the drill previously developed under Contract H0282044 were made and tested at an Eastern Pennsylvania mine. These improvements were: 1. Better hole cleaning due to the development of an air-water mist flushing system. 2. The application of roof drill bits to allow drilling through rock seams and lenses. 3. The development of a quick coupling drill system which reduced total steel change time. 4. Adaptation of a swivel to the drill anchoring system which greatly reduced set-up time between holes. With these improvements the probe drill demonstrated its ability to drill the required 11 holes in one shift. It also gained miner acceptance as a viable underground working tool. The probe drill proved to meet all of the design requirements of portability, low weight drilling controllability, structural integrity and reliability. In addition to its ability to drill the required probe pattern, the probe drill has the capability of drilling long holes. By drilling several holes over 80 feet deep the probe drill has demonstrated a potential for use in robbing pillars and for methane drainage.

Jan 1, 1981

By J. S. Malesky

"INTRODUCTION The Airdox method of breaking coal utilizes compressed air under high pressure and was developed to replace explosives. It is used in Illinois and Indiana mines to a large extent and also has been introduced in mines in a few other States.ACKNOWLEDGMENTThe author gratefully acknowledges the information and photographs furnished by the Cardox Corp.HISTORYIn the early 1920's, with the adoption of mechanical mining in States where on-shift shooting was prohibited, it became desirable to develop some means of breaking coal from the face without the use of explosives. At that time it was thought that a pressure of 20,000 pounds per square inch would be necessary to break the seal. It was impossible to obtain a compressor that would develop this pressure therefore, the 'patentees developed and applied the Cardox method, which utilizes liquid carbon dioxide as the blasting medium."

Aug 1, 1948

By W. M. Traver, A. M. Evans

"INTRODUCTION The Bureau of Mines undertook exploration in the Torlingua district, Texas, during June 1943, at a time when the demand for mercury for war industries was considerably more than the anticipated domestic production. In view of the impressive past production of the mines and the favorable geologic conditions in several underdeveloped areas in the district, the investigation was considered of immediate importance.Prior to initiation of the exploratory program, a preliminary examination of the district was made in August 1942 by A. B. Needham, an engineer of the Bureau of Mines. This examination was followed by a comprehensive geological study by the Federal Geological Survey 3/ and further investigation the Bureau of Mines."

Jan 1, 1947

By P. A. Bloom

Arsenic-containing flue dusts are currently being stockpiled by several nonferrous smelters in the United States. These stockpiles are a source of environmental concern since the dusts can be transported by wind and contain water-soluble arsenic. The stockpiles also represent an alternate source of metals. To provide a quality environment, the Bureau of Mines investigated a process to make environmentally acceptable the discard of arsenic obtained from the treatment of arsenical flue dust. The process includes (1) leaching arsenic from a lead smelter copper dross flue dust, (2) fixing arsenic as an insoluble compound, and (3) recovering other metal values. Overall results of acid-leaching tests on lead-smelter flue dusts showed that H2S04 dissolved 80 to 90 percent of the As, Zn, and Cd, and up to 86 percent of the In. Pb, Ag, and Au remain in the residue, which can be recycled to the smelter. Indium was recovered from the strong acid leach solution by solvent extraction; arsenic was fixed in a stable form by precipitation with Fe2(S04)3 and CaO or CaC03.

Jan 1, 1982

By K. P. Wang

SIGNIFICANT general developments took place in the Far East during 1964, with far-reaching repercussions on the mineral and industrial economies of individual countries and the region as a whole. Japan, during this, "the Year of the Open Door," ushered in the era of industrial maturity, greater independence in economic policy, and expanded technical assistance to less developed countries. Symbolic of its dynamic economic growth is the fact that Japan out-produced the Federal Republic of Germany in steel during 1964 to take over a third-ranking world position. Mainland China, recovering from the "Leap Forward" debacle, made significant gains in industrial output. Mainland Chinese trade with Japan was on the upswing, and discussions were held between the Chinese and the Soviets for possibly resuming Soviet aid in industrial and mineral development. Meanwhile, United States aid to Taiwan was being phased out because of progress achieved. Rapprochement between South Korea and Japan was imminent late in 1964, a factor which may well affect South Korean mineral development. The Indonesian-Malaysian confrontation created economic difficulties in both countries. The war in Viet-Nam seriously disrupted industrial activities, particularly in the south.

Jan 1, 1966

The question of earth models has repeatedly arisen in our work. An accurate representation of the seismic properties is required for three reasons: 1.To be able to determine from a set of received arrival times, the location of a seismic source in the earth, and secondly the degree of accuracy required in the model used for calculating source location from the set of arrival time differences. 2. To be able to determine the expected arrival times at an array of geophones produced in response to a hypothetical source in the earth. 3. To be able to estimate received signal strengths more accurately. The work reported here on earth models is based on information from sever- al consultants and from others who expressed an interest in the problem and supplied information to us. II. COAL MINE GEOLOGY On one of our earlier assignments for the Bureau of Mines, Earth Science Research Inc. of Cambridge, Massachusetts prepared for us a short description of the lithology to be expected at coal mine sites. This description follows, together with the ranges of compressional seismic velocities (Figure I*) associated with typical materials comprising the layered structure of a coal mine area. Coal is primarily associated with fresh water sediments including sandstones, shales, and clays, and occasionally may be metamorphased to varying degrees. In the Appalachian Basin the coal beds occur within cyclical sequences of non-marine shales, sands tones, conglomerates, limes tones, and clays. The beds range in thickness from a few inches to 60 feet, averaging between 2 feet and 10 feet. They have generally broad areal extent, occasionally up to 5,000 square miles, and have an overall tabular or lens-like shape. Within a particular lens, local changes in thickness are normal.

Jan 1, 1974

By R. D. Leitch

In the course of another investigation4 during 1926 and 1927, samples of water collected from a few abandoned coal mines indicated that their drainage was usually lower in acidity than water from active mines in the same locality. In order to determine whether this condition might have a bearing on the advisability of sealing abandoned mines, a number of such mines were visited, samples of drainage were collected, and as much information as possible was obtained from officials of the mining companies and older residents of the district. The results of this work are the basis of the present report. ACKNOWLEDGMENTS The authors are indebted to E. W. Robertson, F. F. Spowart, J. H. Nagle, and W. D. Adams of the Northwest Mining & Exchange Co.; E. M. Fasset, Fred Lane, Wm. Humphreys, and Dr. T. A. Hutchison of Brockway, Pa.; C. W. Faulk of the Shawmut Mining Co.; James Hau of Kersey, Pa., and do others for information received; and to Dr, R. R. Sayers of the Bureau of Mines, under whose direction the work was conducted.

Jan 1, 1928

By W. J. Fullerton

This paper is one of a series being prepared by the U. S. Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States, end deals directly with methods and costs at the quarry and mill of the North American Cement Corporation at Catskill, N. Y. The process of manufacturing cement is described only as far as the final grinding of the raw materials. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual producers, as well as to the industry as a Whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding; of the scone of the cost tabulations may ensue.

Jan 1, 1931