Search Documents

By Heine Kenworthy

In 1930 the Shenandoah-Dives Mining Co. near Silverton, Colo., put into operation a newly erected, 300-ton selective flotation plant to mill complex ores from its nearby mine. The operation was a steady producer and was enlarged to treat 600 to 800 tons a day. In 1942 the company opened and started milling an area in the mine containing semioxidized ore. The valuable mineral. Content of this ore was considerably higher than in the straight sulfide ore previously handled alone. The mixture of clean sulfide and semi-oxidized ore was difficult to treat; consequently tailing losses, especially with respect to lead, were high. A. few years later, in order to study the possibilities, of obtaining higher recoveries by a modification of the mill flow sheet, a 1,200-pound sample of mill feed, taken over a period of several days by the company, was submitted to the Mississippi Valley Experiment Station for testing. Although this sample proved to contain more than twice as much lead as the average yearly mill feed, the same problem of recovering the oxidized values were present.

Jan 1, 1948

By R. Wiebe

During a recent investigation the authors were interested in determining: (1.) How many points were necessary to locate the deviation curve for copper-constantan thermocouples within an accuracy of about 0.05° C., used in connection with the "standard" thermocouple of L. H. Adams. (2.) Whether copper-constantan thermocouples showing considerable deviations from the "standard' were consistent throughout their calibration. (3.) How reliable the extrapolated portion is - that is, the interval between -183 and -220° C. of the "standard" thermocouple. It seems that a calibration between 0 and -193° C. can be made within the stated accuracy by determining experimentally the e.m.f. of the particular couple at -78.50°, the normal sublimation point of carbon dioxide, and at -182.97°, the normal boiling point of oxygen. Substituting the values found for the two fixed points in the simple quadratic. Equation

Jan 1, 1931

By H. J. Hager, B. W. Gandrud, G. D. Coe

"INTRODUCTION The reduction of washery losses of marketable coal is a phase of coal preparation important to many of the Alabama coal producers. The problem has wide scope, and this report deals with but one of its several aspects. The investigation on which this report is based was made by the Southern Experiment Station of the Bureau of Mines with the cooperation of the Alabama By-products Corporation and the University of Alabama. The Alabama Byproducts Corporation provided samples of table middlings from its Colta washery on the Mary Lee bed at Flat Creek, Ala.PRACTICE AT THE COLTA WASHYAt Colta run-of-mine coal is crushed in a hammer mill in closed circuit with 5/16-inch square-mesh vibrating screens and tabled without classification on eight rectangular-deck wet tables. The coal is more friable than the bone normally present, and hence the bone is concentrated in the coarser sizes. An unclassified feed of this character can not be tabled with high efficiency to low ash content because of the sizing action of a concentrating table, which is such that when the tables are adjusted to exclude the coarse bone from the washed coal, a large amount of fine coal is lost in the middlings. At the time this investigation was undertaken there was no market outlet for middlings, with the result that middling products had to be discarded with the refuse."

May 1, 1939

By W. W. Adams, V. E. Wrenn

"Production of explosives in the United States during the calendar year 1935 decreased 2 percent from 1934, according to reports covering all companies engaged in the manufacture of explosives during those years.Reports from manufacturers showed a total production of 308,381,250 pounds of explosives; this quantity included 39,170,016 pounds of permissible explosives 5/ 200,323,559 pounds of high explosives other than permissibles, and 68,887,675 pounds of black blasting powder of which 34,222,625 pounds were granular powder and 34,665,050 pounds pellet powder.Coal mines consumed 89 percent of the total production of blasting powder, 99 percent of the total output of permissible explosives, and 11 percent of the output of other high explosives.The metal mines of the United States used 28 percent of all high explosives other than permissloles, less than 1 percent of all permissibles, and 1 percent of all black powder produced.Quarries and nonmetallic-mineral mines consumed 17 percent of the high explosives other than pormissibles, less than 1 percent of the permissible., and 3 percent of the blasting powder.Construction work required the largest quantity, 40 percent of all high explosives manufactured during the year. Less than 1 percent of the permissibles and 6 percent of the black powder produced during 1935 was used in construction work."

Nov 1, 1936

By P. G. Clites

A laboratory furnace was developed by the Federal Bureau of Mines for use in studying the interrelationships among variables associated with skull melting and casting high-temperature metals. Although additional work is necessary to determine the extent to which the information obtained by using this furnace can be extrapolated to larger furnaces of the same type, many casting characteristics of metals and alloys can be determined on equipment of this size. This furnace is a laboratory-size, consumable-electrode, skull-casting furnace equipped with a water-cooled copper ladle. The ladle, which is a tilt-pour or over-the-lip type, has a volume of approximately 30 cubic inches and provides up to 20 cubic inches of molten metal for castings. Castings of various reactive and refractory metals, including zirconium, titanium, hafnium, columbium, molybdenum, tantalum, and tungsten, have been produced. In addition, castings of iron, chromium, and copper have been made. The simplicity and versatility of the apparatus would make it useful to metallurgical laboratories preparing cast specimens.

Jan 1, 1961

By Daniel T. Rogers

The Bureau of Mines, in its alumina miniplant project to investigate alumina recovery from domestic, non bauxitic ores, has conducted research on the use of a hydrochloric acid leaching, gas sparging crystallization technology. An important element of this research is the efficient separation of undissolved, siliceous residue from AICI3 -bearing leach liquors by continuous, horizontal, countercurrent vacuum belt filtration. In an effort to calculate material balances quickly and to predict material balances based on different belt filtration configurations, the perfect-mixing-cells-in-series model (PMCS) for calculating material balances around belt filters was used. Because of the porous nature of the solids, the model produced erroneous material balances. Therefore a reliable model, the shrinking voids model, was developed postulating the presence of an unwashable voids liquor volume that decreases with decreasing liquor AICI3 concentration. This volume decrease postulation is equivalent to assuming that dilute liquors flow more freely, causing more voids liquor volume to become washable. Least-squares based computer programs are provided, which are useful not only in producing material balances from plant data but also in predicting balances for untested configurations using the same feed materials.

Jan 1, 1982

By Robert C. Johnson

Single crystal whiskers of ZrO2 and TiO2 were grown by solution and crystallization of these oxides in molten baths. Mixtures of Na2B407 and LiC1 were the most suitable growth media for zirconia. Sodium borate alone and Na2CO3 plus SiO2 were best suited for titania. The solubilities of zirconia and titania in molten sodium borate were determined, Whether zirconia whiskers were dendritic or nondendritic depended on the temperature used. The best single crystal whiskers were grown below 1,100° C. Titania whiskers always grew as single crystals. The tensile strengths of zirconia and titania whiskers were about 15,000 psi and 50,000 psi, respectively. Modulus of rupture was about 49,000 psi for zirconia whiskers and 75,000 psi for titania whiskers. Chemical analyses showed the zirconia and titania whiskers to be pure. The zirconia and titania whiskers were shown by X-ray analysis to be, respectively, baddeleyite and rutile.

Jan 1, 1965

By Wallace W. Roepke

Research to evaluate the lubricity effects achieved by spraying water on the cutting bit of a mining machine or spraying water on the coal during cutting has shown that neither practice affects cutting forces, as had been believed. However, when water was supplied to the cutting zone axially through the bit at 3,000 to 5,000 psi pressure, tangent'ial cutting forces were reduced an average of 30 pct at a I-in depth of cut while normal bit forces were reduced an average of 65 pct. Lower normal forces mean reduced bit wear, faster advance with greater depth of cut, and fewer coal fines.

Jan 1, 1985

By W. W. Roepke

The linear cutting system, developed by the U.S. Bureau of Mines, uses geometric principles developed by Cardan to produce a nearly constant cut depth. The new system has been extensively tested in a synthetic material under laboratory conditions to verify mechanical capability and to identify operational characteristics. Comparisons between 15-rpm linear cutting and 50-rpm rotary cutting systems show significant improvement in respirable dust entrainment, product size distribution, and energy usage. Respirable dust is reduced by as much as 90 pct. Recovered product showed a 67-pct reduction in -0.32-cm (-1/8-in) material and a 200-pct increase in +5.08 cm (+2 in) material. Average power was reduced by 66 pct for the linear cutting. Because the bit cutting paths differ between linear and rotary cutting, it was necessary to compare the two at the same cut depths and bit types. These comparisons show that low revolution per minute rotary cutting entrains about the same amount of respirable dust as the linear cutting system, but the average shaft torque may be 55 to 130 pct greater for the rotary system.

Jan 1, 2010

By W. E. Webb

This report describes a method the Bureau of Mines devised for measuring the dielectric constant and loss tangent of low-loss minerals at microwave frequencies. Determina-tion of these properties makes it possible to predict the effects of using microwave heating in potential mineral processing applications. The method uses a test cell and radio-frequency (RF) impedance analyzer with automated data acquisition and analysis. In this initial phase of microwave heating research, the Bureau measured dielectric constants and loss tangents at frequencies between 100 MHz and 1 GHz. The objective was to establish a reliable data base for use in predicting the effects of microwave heating on minerals. Comparison with previously measured data showed the Bureau's measurement method to be accurate to within ± 3 pct. This report describes the method and discusses the preliminary results of the Bureau's investigations. Typical comparative data are included.

Jan 1, 1986

By Eric E. Ungar

Some fundamental facts regarding noise are summarized. Guidelines for reducing plant noise are indicated, and simple means are discussed for determining, whether quieting of specific equipment items will reduce plant noise significantly. Design and installation recommendations are made for quieting chutes by means of dams, impact cushioning pads, impact shields, and damping materials, and for quieting; screens by means of resilient decks, lined screen bottoms, drive mechanism enclosures, and side plate additions. A brief account is appended of the wear and productivity performance of resilient materials observed in three cleaning plants.

Jan 1, 1976

By Floyd D. Everett

The Cougar Spar property is in southwestern Beaver County, Utah, approximately 35 miles by road northwest of Lund, a station on the mainline of the Union Pacific Railroad (fig. 1). Original fluorspar discoveries on the property were made a. short time before 1941. During 1941 lessees produced approximately 600 tons of ores averaging 40 percent CaF2. Bureau of Mines engineers examined the property in 1942 and recommended development. Work was begun in December 1942 and completed in October 1943. The area was mapped by members of the Federal Geological Survey during the project period. Development included surface trenching; drifting, and crosscutting, a short distance below the outcrop. The surface work comprised a total of 440 linear feet of bulldozer and hand trenches. A total of 550 feet of workings was driven on the 100-foot level. Samples were taken for assay from the trench exposures and from the underground workings as work progressed. Pocks in the area of the Cougar Spar property are igneous and consist mainly of fine-grained tuff and quartz monzonite porphyry. The fluorspar mineralization occurs in a northwest fault zone.

Jan 1, 1951

By R. J. Leary

Oxidation testing of copper-clad steel strip was performed in a muffle furnace to determine whether copper in contact with steel scrap could be removed by oxidation in an airstream at high temperatures. Substantially all of the copper was oxidized before any significant iron oxidation occurred. The rate of copper oxidation was not affected by contact with iron. Copper oxide scale separated spontaneously from the underlying metal during cooling. Results indicate the possibility of removing light-gage copper coatings and components from ferrous scrap by oxidation in an incineration process.

Jan 1, 1965

By G. M. Potter

During the investigation of the occurrence of manganese deposits in the western United States, examining engineers of the Bureau of Mines collected samples from four properties in Siskiyou and Mendocino Counties northern California. As the ores were too low-grade to be acceptable to manufacturers of ferromanganese, beneficiation studies were made between 1941 and 1945 to determine the amenability of the ores to concentration. The Johnson and Reynolds properties are near Fort Jones Siskiyou County. The ore occurs in a number of small lenses in that area. Samples were taken for testing for amenability to treatment in a small custom-gravity plant, tentatively planned. by the Waiter Johnson interests of San Francisco. A 2-ton representative sample was obtained from numerous exposed portions of an outcrop on the property of the Mayland Mining Co. The Mayland mine is about 8 miles from Sawyers Bar in Siskiyou County. The ore body consists of stringers and irregular masses of oxide, and. silicate ore scattered through quartz, which these minerals have replaced.

Jan 1, 1952

By C. A. Komar

The Bureau of Mines has undertaken an investigation to determine possible applications of acoustic energy at sonic and ultrasonic frequencies to improve ultimate recovery from oil reservoirs. A literature search was conducted to provide background information for initiating laboratory research. The purpose of the literature search was to review the uses that have been made of acoustic energy in the petroleum industry and to select procedures and techniques that could be applied to the solution of petroleum production problems. The characteristics (68)3 of ultrasonic energy make it potentially useful to a variety of industrial and experimental applications. Pulse techniques (99) are common in the testing of materials where inspection is accomplished by propagating an ultrasonic pulse through the material. Viscosity measurements (45) are made by interpreting changes in the absorption of sound as it is propagated through a flowing liquid. Cavitation phenomena (93) produced by high-intensity ultrasound in liquids have been used extensively in industrial cleaning, machining, impact grinding, and aluminum soldering operations.

Jan 1, 1963

By Arne Landsberg

The Bureau of Mines measured the vapor pressure of FeC12 , FeBr2, FeI2, Sb, Bi, Cd, Mg, Pb, FeC13 , and VCl2 using the Knudsen-and torsion-effusion methods, and on FeC13 -NaC1 mixtures, Au2Cl6, and MgNi2 using only the Knudsen method. Apparent vapor pressures calculated from the experimental data vary with orifice size and method of determination. Reaction with residual oxygen in the instruments was noted to have an effect on the iron halide data. Vapor pressure curves plotted as log P versus 1/T (where P is pressure and T is absolute temperature) for one substance using several orifice sizes tended to converge at a single point when extrapolated beyond the experimental region. All of the data, except those of VC12, agree with previously published results. The importance of comparing effusion measurements with those obtained by other methods and the variations encountered with various orifice sizes are discussed.

Jan 1, 1977

By R. K. Koch

The vapor pressures of liquid molybdenum and liquid zirconium were determined by the Langmuir free-evaporation method. An electron-beam furnace with a water-cooled copper crucible was used for melting. Temperature was measured with a two-color ratio pyrometer. The vapor-pressure data led to the following equations: [log p (atm) = 5.429 - 28,380 T for liquid molybdenum in the range 2,890° to 2,990° K, and log p (atm) = 6.521 - 30,940 T for liquid zirconium in the range 2,229° to 2,795° K.] Third-law evaluations of each data set gave mean heats of sublimation (298.15° K) of 157.6 ± 1.8 kcal/mole and 148.4 ± 2.4 kcal/mole for molybdenum and zirconium, respectively, where the uncertainties are two standard devia¬tions. Second-law standard heats of sublimation determined from sigma plots and tabulated enthalpies were 143.5 ± 2.7 kcal/mole and 149.2 ± 3.8 kcal/mole for molybdenum and zirconium, respectively. The better agreement in heats of sublimation for zirconium is attributed to the 566° K temperature range studied which permitted a more accurate definition of the vapor pressure curve than could be obtained from the 100° K span for molybdenum. This supposition was verified by making a sigma-prime plot which utilized solid vapor pressure data for molybdenum to extend the evaluation range by 800° K. This gave a standard heat of sublimation of 155.2 ± 1.6 kcal/mole which is in good agree¬ment with the third-law value. The plot also gave a standard entropy of sublimation (298.15° K) of 35.73 ± 0.48 eu.

Jan 1, 1968

By William J. Campbell

These investigations were undertaken as part of a program to determine the optimum X-ray spectral lines to use for analyzing the wide variety of samples received by the X-ray Laboratory. Theoretical calculations and experimental data derived from these investigations show that longer wavelength spectral lines, > 2A, are very useful for many analytical problems. Because of the low fluorescence yield of the elements of atomic numbers 13-22 and the small depth of penetration of their X-ray spectral lines, these elements were originally considered to be insensitive; however, these studies show that the wide dispersion of their spectral lines, coupled with their weak beta lines, permits the use of wide collimation, thus increasing the line intensity. More importantly, the background due to scattered primary radiation is very low in the long-wavelength region.

Jan 1, 1959

By E. B. Kester

A study of the composition of the corresponding fractions of a primary and a high- temperature tar was undertaken to throw light on the net results of the pyrolysis of the primary products of coal decomposition in high-temperature coking practice, with reference both to total quantities of the chemically similar constituents and to their distribution throughout the boiling range. No exactly parallel investigations are on record. The distribution of substances in high-temperature tars, however, is fairly well understood. Such tars are more or less similar, for they consist of the more stable phenols, aromatic and olefinic compounds resulting from the pyrolytic decomposition of a wide variety of primary tar constituents. For example, from a typical distillation curve for high-temperature tar phenols4 it may be seen that the greatest portion of the phenols distills between 180° and 220° C., a fairly narrow range.

Jan 1, 1932

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the seventeenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes.

Jan 1, 1948