Search Documents

By C. J. Chindgren, L. C. Bauerle, J. B. Rosenbaum

Modifications of the conventional method of preparing ductile vanadium metal by calcium reduction of V2 05 in a bomb were explored for clues to a more economical procedure . The modifications examined included ( 1 ) omitting the gas purge of the bomb ordinarily used for eliminating atmospheric nitrogen , (2 ) using low- grade vanadium feed materials , ( 3 ) using alternative reductants , such as aluminum , magnesium , and silicon , and reductant mixtures , and ( 4 ) bomb refining of aluminothermic metal produced in open- vessel reductions . The most promising modification appeared to be bomb refining , using calcium to purify vanadium metal -- of low aluminum but high oxygen content-- prepared by open- vessel aluminothermic reduction of vanadium pentoxide .

Jul 1, 1960

By H. H. Schrenk, L. B. Berger, W. P. Yant, F. A. Patty

"The use of small such as canaries and white mice, for detecting carbon monoxide depends primarily on the fact that the volume of respiration of these animals in proportion to their volume of blood is much higher than for man. Accordingly, when animals and men are simultaneously exposed to a given concentration of carbon monoxide the animals will absorb it more rapidly and attain serious poisoning in less time than men. Prom a practical viewpoint the use of the animals depends on the margin of time between observable symptoms in them and serious poisoning in man, during which man can return to fresh air or use respiratory protection. It should be remembered, however, that during the time the animal is incurring a detectable degree of poisoning, man is also absorbing some carbon monoxide, and the margin of time is not very wide. Experience with canaries has shown that an occasional specimen may have a tolerance above the average of the species and fail to exhibit symptoms before man incurs a very discomforting and possibly a serious degree of poisoning.It is also well known that physical activity increases the demand for oxygen by the body, and the respiratory exchange and circulation of the blood are increased to meet the demand. This sets up a vicious condition if carbon monoxide is present in the air because the rate of absorption of carbon monoxide is not only increased by the increase in respiration and circulation, but the absorption of carbon monoxide decreases the capacity of the blood for carrying oxygen at a time when the demand is high. These facts, together with the increase in respiration and circulation which attend excitement, underlie the caution to be calm and to walk slowly and to reduce physical exertion to a minimum when exposed to carbon monoxide. For these same reasons, when using animals for detecting carbon monoxide it is endeavored to keep them active, thereby tending to increase the response of the birds and widen the time between observable effects in the birds and effects in the man. As rule canaries are kept fairly active through fright at the unnatural surroundings and in their endeavor to remain on the perch of the cage when carried into the atmosphere to be examined. They also experience an excitement stage with oncoming carbon monoxide poisoning. Sometimes, however, especially if the air is cold, they tend to be inactive and quiet. Ordinary mice and white mice become inactive with use and also with oncoming poisoning. They huddle in the corner or the cage, and thereby not only reduce their sensitivity but make it difficult to observe signs of poisoning."

Oct 1, 1930

By C. W. Davis

This is the first of a series of papers being; prepared as the work progresses in a study of the hydrometallurgy of manganese. The investigation is being made in an endeavor to make possible the utilization of lour-grade domestic manganese ores. The value of a hydrometallurgical process for manganese depends on the present and future uses for manganese products.

Jan 1, 1930

By A. Gene Collins

This report discusses some of the chemistry and geochemistry of cesium and rubidium. Knowledge of the cesium and rubidium content of oilfield waters aids in resolving the origin of waters and petroleum, exploring for petroleum and other valuable minerals, discovering water pollution sources, and augmenting the knowledge of geologic formations. The methods described in this report permit the detection of less than 0.01 mg/l of cesium and/or rubidium in a complex oilfield brine or water. Solvents possessing high-dielectric constants were evaluated for their ability to extract cesium and rubidium tetraphenylboron from oilfield waters and for their flame emission characteristics. Nitroethane was selected and used for the extraction and flame spectrophotometric determinations because it gave the highest sensitivity. Cesium 137 and rubidium 86 were used to determine the extraction efficiencies, which were about 87 percent and 58 percent respectively using a single 10 ml nitroethane extraction from a distilled water matrix. The standard deviation of the determination was 0.0008 mg for cesium and 0.0007 mg for rubidium in the 0.01 mg range.

Jan 1, 1965

Exposure to airborne respirable crystalline silica dust can lead to silicosis, a debilitating lung disease. On surface coal mining and construction sites, blast hole drills are notorious sources of airborne respirable dust that may contain significant amounts of silica. The drill operator and drill helper usually receive the greatest silica exposure compared with other occupations. As a result, many drilling operations have been, and still are, on more stringent dust standards. Drilling through various rock formations naturally presents a strong potential for silica dust generation for several reasons. First, drilling is a pulverizing process that generates large amounts of very small dust particles. Second, the bailing air used to flush cuttings from the hole leaves the hole at a very high velocity and can be difficult to contain. Third, many fixed shrouds used to enclose the area beneath the drill deck have a significant amount of leakage due to 1) gaps between the shroud and ground created by raising/leveling the drill, 2) gaps in the corner seams, and 3) tom deck shrouds. CONTROLS A dry dust collection system is typically connected to the drill deck to collect dust as the bailing airflow transports the cuttings (and significant amounts of airborne respirable dust) out of the drill hole. Deck shrouds are installed in an attempt to enclose the volume around the drill steel and prevent dust escaping. However, most deck shrouds are rectangular and constructed of four separate pieces of rubber belting attached to the deck. Because of this design, there is usually a significant amount of dust escaping from the open seams as well as the open area between the shroud and the ground. This dust can be a significant source of silica exposure to drill operators as well as other personnel downwind of the drill.

The purpose of Volume II of this study is to provide a general plan for the pilot testing of two materials which could be used to tag explosives for both pre- and postdetonation identification and of tracing techniques which would thereby aid the investigator of an unauthorized bombing or explosion in being able to determine the source and/or user of the explosives. Volume I described the planning factors by which the tagging of explosives could be implemented on a National basis. 1.2 BACKGROUND Tagging explosives at the time of manufacture with a taggant material that could survive detonation, be recovered, and provide an investigative lead has been seriously studied for several years. This concept has gained widespread support among many law enforcement groups because of the scant clues that can presently be found among bombing residue.

Jan 1, 1977

By L. C. IlsLey

The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting,but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely how methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.

Jan 1, 1936

By Graham W. Marks

This report is the fourth of a series concerning the development of spectrochemical methods for the analysis of ore samples and related Metallurgical materials by the total-energy method. In this report, the application of this method to the determination of thallium is discussed. This element lies in group III of the periodic tale; one other Clement of this group; indium, has already been investigated.

Jan 1, 1949

By L. C. IlsLey

[The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely show methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.]

Jan 1, 1936

By D. R. Brooks

The Bureau of Mines has tested a dewatering technique for phosphatic clay waste. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen or trommel. In field tests conducted in central Florida, clay wastes containing approximately 4 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO-treated material will dewater to 30 pct solids in 80 days. Pretreatment of phosphatic clay waste with lime lowers the PEO dosage required for dewatering.

Jan 1, 1986

By Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average Sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining.

Jan 1, 2010

By L. C. IlsLey

So many subjects are covered in State mine-safety regulations that any attempt to compare different State laws in their entirety would be futile. On the other hand, if one selects a single phase or branch of safety work, such a comparison may prove profitable. The subject selected for study in this paper is limited to legislation or regulations dealing specifically with safeguarding (electric) motored equipment used in gassy mines. T When one reads glowing accounts of the safety activities being carried on here and there it is easy to believe that everything which is right and proper is being done to safeguard the mine.workers; but, when one takes time to look into the weakness of many State regulations, it is evident that there is still room for improvement. Undoubtedly it would have been much better for the safety of mines if electrical equipment had been introduced into mines 50 years earlier. If electricity had been in general use when the first mine regulations were pre- pared, those formulating the rules would have covered this hazard along with other hazards, but as electricity came in at a later period, safe mine legisla- tion regarding it has been woefully neglected. Today the United States in general is far behind most other coal-producing nations in the provision of adequate safety rules or laws for the installation and maintenance of electrical equipment and wiring. Returning to the subject of our study, approximately 30 of the 48 States mine coal. More than 20 of these States' produce coal in large quantities. How- ever, of the 30 States only four, 3 Pennsylvania, Utah, Washington, and West Virginia, have laws which specially call for the use of explosion-proof types

Jan 1, 1929

By Roy E. Peterson

The Bureau of Mines conducted an investigation to produce metallized pellets from domestic iron ore superconcentrates using lignite and subbituminous coal as reductants. Feed materials for the metallizing process consisted of commercially indurated iron oxide pellets and green pellets prepared from upgraded domestic concentrates with graphite or limestone as internal additives. Durability of the green pellets during metallization was investigated in tests conducted in a 7-inch-ID rotating drum furnace. Test results indicated that the major cause of pellet disintegration with the concentrates used was the tumbling action during reduction rather than forces generated within the pellets. In larger scale tests made in a 34-inch-ID by 35-foot-long kiln, the previously indurated pellets were metallized with lignite at 1,030° C with little disintegration. A 96-percent level of metallization was obtained in pellets having an average compressive strength of 420 lb. In subsequent, similar tests using green pellets containing graphite or limestone, pellet disintegration was more severe, with 10 to 40 percent of the feed being lost as dust. The surviving pellets had metallizations ranging from 88.3 to 94.4 percent and compressive strengths ranging from 60 to 68 lb.

Jan 1, 1976

By Mark R. Pettitt

The results of an extensive research and development program to reduce the noise generated during coal cutting are presented. The characteristics and magnitude of continuous miner coal cutting noise sources are defined. This work consisted of development of a simulated coal ,cam to facilitate above-ground coal cutting tests, noise measurements in a reverberant acoustic chamber during simulated mining operations of a continuous miner (cutting the simulated coal scam), and noise measurements in an underground coal mine during continuous miner operation. In-mine and laboratory test results were in excellent agreement for both A-weighted overall levels as well as A-weighted one-third octave band spectra. Methods to reduce coal cutting noise are presented. These methods take full advantage of the dynamic characteristics of the forces generated during coal cutting. Dynamic cutting force isolation was shown to be a very effective technique. Finally, a continuous miner was equipped with a cutter head that incorporated (among other design factors) cutting force isolation. Successful, lung term, in-mine use of the cutter head demonstrated coal cutting noise at the operator's station of less than 90 dBA and 50% coal, 50% rock cutting of less than 93 dBA.

Jan 1, 1985

By R. G. Gürtunca

The future of the United States (US) mining industry will be affected greatly by recent coal mining disasters. These have resulted in new legislation which will have an impact on mining economic costs as well safety and health of miners. This paper discusses the changes that new legislation and regulations are making to the industry and current research that is producing technologies to make mining safer and will likely impact the future of mining.

Jan 1, 2009

By J. B. Janus

This report, the 22d in a series, gives analytical data showing composition and quality of tipple and delivered samples of coal collected during fiscal year 1972. This coverage lists mines located in 20 States. Ultimate analyses are given for most of the coalbeds listed. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. The deliveries were sampled in accordance with instructions issued by the Bureau of Mines, and the samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1973

By K. E. Stanfield

The Bureau of Mines oil-shale program, initiated in April 1944, is concerned with the future utilization of oil shale in the United States as a source of liquid fuel. One phase of this program is the accumulation of information on the location, extent, and richness of oil-shale deposits that may be suitable for processing to oil and related products. A previous publication5/ presented, by means of logs, the oil yields of sections of the largest known oil-shale deposit in this country -the shales of the Green River formation occurring in adjoining portions of the states of Colorado, Utah, and Wyoming. This present supplementary report presents the oil yields of cores from 48 holes drilled during 1952 to 1954 in the Green River formation of Colorado, which is distributed over an area of more than 1,000 square miles. The oil yields of the 48 oil-shale sections, involving the assay of 9,651 samples, representing 22,451 feet of core, are presented by means of logs. In addition, the oil yields of samples comprising the maximum sections of 15 gallon-per-ton shale are tabulated for these cores and for the 28 cores from Colorado which were logged in the previous report.

Jan 1, 1957

By G. R. Peterson

The Bureau of Mines evaluated the potential supply of cobalt from known domestic resources, both as a primary product from some deposits and as a byproduct from others, and found that U.S. production could play an important role in meeting U.S. cobalt needs by the mid-1980's. This production would be of a relatively short duration, however, with production declining significantly before the year 2000. As part of the study, a tonnage-price relationship was developed indicating the quantity of cobalt that could be produced from known cobalt-bearing deposits at various primary commodity prices and at a 15-percent rate of return on the required capital investment. All capital and operating costs are calculated in August 1980 dollars, and commodity prices are based on August 1980 prices. Known U.S. cobalt-bearing deposits which represent the current U.S. cobalt reserve base contain some 310,800 metric tons of cobalt in slightly over 1 billion metric tons of demonstrated mineralized material. Approximately 37 percent of the cobalt contained in the reserve base is considered recoverable using existing technology. Of this quantity, some 87,000 metric tons of cobalt is economically recoverable assuming a cobalt price of $25 per pound, a copper price of $1 per pound, and a lead price of $0.40 per pound. Assuming that the cobalt price decreases to $15 per pound, keeping copper and lead prices constant, the quantity that is considered economically recoverable declines to some 45,700 metric tons. Domestic cobalt consumption in 1979 was 7,900 metric tons (17.4 million pounds). Currently, no primary cobalt is produced from domestic resources, and none has been produced since 1971.

Jan 1, 1981

By E. J. Gleim

In the movement of self-controlled direct-current machinery, particularly shortwall cutting, machines, from one place to another in coal mires, "nipping" or it stinging" has been practiced quite commonly. These terms refer to the method of obtaining current for propelling or tramming the machines along trolley haulageways by sliding the trolley trip (hook or nip), which terminates one conductor of the trailing cable, along the trolley wire. This is usually done by the machine operator or runner while sitting on the machine truck and holding the nip terminal against the trolley wire as the machine travels along the rails. This procedure is objectionable for several reasons. Under the best conditions, the area of contact between the nip and trolley wire is snail end, consequently, sparking and flashing ore most likely to be continuous as the machine proceeds. This is undesirable, not only because of the detrimental effect of electric flashes upon eyesight, but because of the pitting and roughening the trolley wheels which decrease the efficiency of current collection by locomotive trolley wheels and shoes and at the same time shorten their useful life by increased wear.

Jan 1, 1939

A construction material based on plasticized sulfur and mineral aggregate, that is superior in corrosion resistance and strength to portland cement concrete. The material can be used in the chemical, metallurgical, and fertilizer industries, and will also provide an attractive market for by-product sulfur resulting from compliance with pollution regulations. How It Is Made Sulfur concrete is thermoplastic material. Plasticized sulfur is mixed with sand and gravel aggregate heated to 375-400° F. The sulfur melts and acts as the binder or cement. The sulfur concrete is poured hot and sets at a temperature of 200° F. Full strength is attained in a few hours, compared to several days for portland cement concretes. Sulfur concrete even pours and sets in freezing weather. Although unmodified sulfur with aggregate will produce a sulfur concrete with good initial properties, it undergoes crystallographic modifications, and deteriorates with time, particularly when exposed to moisture or freeze-thaw conditions. The Bureau of Mines has developed plasticizers which, when reacted with the sulfur, give sulfur concretes with excellent moisture and freeze-thaw resistance. The plasticizers are based on mixtures of dicyclopentadlene (DCPD) and ollgomers of cyclopentadiene. About 5 percent by weight of the plasticizers is reacted with molten sui fur for several hours. The sulfur cement can be used directly or allowed to solidify for easier handling and storage.

Jan 1, 1981