Search Documents

By K. J. Maggs

The U.S. Bureau of Mines has investigated the chemical vapor deposition of diamond films on tungsten substrates. The effects of deposition parameters on the adhesion of the films was determined. The films were produced using a hot filament chemical vapor deposition system. Parameters investigated were substrate temperature and methane concentration in the feed gas. Film quality, morphology, and composition were characterized by scanning electron microscopy and Raman spectroscopy. Adhesion testing was performed using an indentation technique, and the results were quantified by relating adhesion to interface fracture toughness. Diamond films with well-faceted crystalline morphology with grain size greater than 1 µm had poor adhesion properties regardless of substrate temperature or methane concentration. Diamond films with smooth morphologies consisting of rounded clusters of small (<0.2 µm) diamond crystallites and amorphous carbon phases displayed much higher adhesion, although the conditions that led to the growth of these films are not understood.

Jan 1, 2010

By R. T. MacMillan

A number of chemical techniques have been applied to manganese ores from three areas of Aroostook County, Maine. Although large tonnages of these ores have been proved, they are low grade, and their exploitation has awaited a suitable beneficiation scheme. As conventional ore-dressing methods had failed to yield satisfactory results, attention was turned to chemical procedures. Leaching with dilute (7-percent) H2S04 extracted over 90 percent of the manganese from ore of the Dudley farm area, consuming 3.8 pounds of acid per pound of manganese extracted. Ores from the Littleton Ridge and Maple Mountain-Hovey Mountain areas were less amenable to this treatment, yielding approximately 80 and 60 percent of their Mn content, respectively. To increase the percentage extraction of manganese in the latter two ores, a number of factors were varied, including (1) acid concentration in the extracting solution, (2) ratio of acid to Mn in the slurry, and (3) preliminary heat treatment of the ore with a reducing agent. Other acids, including HNO3, HC1, and H2SO3, were tried also; however, no significant improvements in the Mn leached from Maple Mountain-Hovey Mountain ore were made. The manganese extraction of Littleton Ridge ore was raised to 90 percent by providing 9 to 11 pounds of HNO3 per pound of Mn in the ore.

Jan 1, 1954

By Stephenson. E. L.

"INTRODUCTION In the spring of 1942 a series of magnetometer surveys on deposits of black sand underlying Pleistocene raised marine terraces along the coast of southwestern Oregon was nada by the Division of Geophysical Exploration of the Federal Bureau of Mines in cooperation with the Oregon Department of Geology and Mineral Industries. A few preliminary tests had been made in the same area in May 1940 and December 1941.The sands contain fine gold and metals of the platinum group, and, beginning in 1852, extensive, but spasmodic mining and exploration have been done for these precious metals. There are many old placer, mines and prospects, although for the most part the yield of the metals has been small. The sands also contain other minerals of potential value, including ilmenite, magnetite, garnet, zircon, and particularly chromite, and the wartime demand for domestic chromite resulted in extensive testing and development of the known deposits. The purpose of the magnetometer surveys was to determine the efficacy of, magnetic methods in tracing and outlining these known deposits and in prospecting for new ones. The field work was done between March 17 and May 29, 1942, by the author assisted by W.W. Paulsen of the Oregon Department of Geology and Mineral Industries."

Jun 1, 1945

Objective: To help prevent squeezes, collapses, and other pillar failures through better pillar design, thereby enhancing safety for underground mine workers.

Jul 1, 1997

The Florida phosphate industry, which supplies about three-quarters of the domestic phosphate fertilizer, produces tremendous volumes of phosphatic clay wastes (slimes). These clays retain a high percentage of water for extended periods of time. The clays also pose an environmental hazard because the disposal technique involves aboveground storage behind earthen dams. Although much research has been undertaken by numerous organizations to dewater slime, no completely satisfactory solution has been developed. In June 1972, a cooperative effort by the Federal Bureau of Mines and the Florida phosphate mining industry was initiated to develop a solution for dewatering the Florida phosphatic slimes. This report discusses various aspects of the slimes problem, reviews past research, makes recommendations for future research, and includes a bibliography of references and patents dealing with the subject.

Jan 1, 1975

By R. T. Sorensen

Research and testing in a small scale equivalent of a commercial flota-tion plant was completed on four low-grade, iron-bearing materials from the western Mesabi range. Closed circuit-flotation of calcium-activated silica with fatty acid collector developed data for comparison with the batch process and highlighted problems not evident from previous bench testing. The four ore samples contained from 27 to 39 percent Fe and were equally represented by nonmagnetic taconite and semitaconite type materials. Iron concentrates containing 6.0 percent, or less, SiO2 were made 5, all four samples. Of the two material types, the semitaconite was the ore amenable to treatment, yielding iron recoveries of about 90 percent as cc pared with 70 to 80 percent for the other. Pilot plant tests showed that concentrate grade made in batch tests could be duplicated in the closed circuit and demonstrated that the amount of recoverable middling iron varied considerably between ore samples. The continuous tests also showed that water temperature strongly influenced results in the treatment of one ore but apparently was of indifferent consequence in another. Progress in thickening and filtration of flotation concentrates was made through introduction of tapioca flour to serve the dual role of iron mineral depressant and flocculant.

Jan 1, 1966

By J. H. Jacobs

In late 1946, research was begun at the Bureau of Mines Electrometallurgical Laboratory at Boulder City, Nev., to determine the possibility of electrowinning manganese from chloride electrolytes on a continuous basis. All phases of electrodeposition were investigated on a small scale it the laboratory, and the results were reported by Jacobs and Churchward. These results indicated that a chloride process had certain possible advantages over the sulfate process that made it worthwhile to continue the investigation on a semi-pilot-plant basis, and this paper reports the results of this work. Research and development work on a process for electrowinning manganese from low-grade ores has been carried on intermittently by the Bureau of Mines since 1936. A process was developed, using sulfate electrolyte, that has been extensively described in the literature.

Jan 1, 1951

A symposium on pneumatic transportation of solids was held at Morgantown, W. Va., October 19-20, 196&apos;), under the cosponsorship of the Institute ref Gas Technology. Chicago, Ill., and the Bureau of Mines. Objective of the symposium was to present information on developments and projected programs in the technology of feeding, transporting, recompressing, and utilizing gas-solids mixtures Dr. Henry R. Linden, Director, Institute of Gas Technology and Harry Perry, Director of Coal Research, Bureau of Mines, in the initial addresses at the symposium welcomed more than 140 representatives of industry, educational institutions, and government from 16 states, Canada, Great Britain, etc.

Jan 1, 1966

A symposium on pneumatic transportation of solids was held at Morgantown, W. Va., October 19-20, 1965, under the cosponsorship of the Institute ref Gas Technology. Chicago, Ill., and the Bureau of Mines. Objective of the symposium was to present information on developments and projected programs in the technology of feeding, transporting, recompressing, and utilizing gas-solids mixtures. Dr. Henry R. Linden, Director, Institute of Gas Technology, and Harry Perry, Director of Coal Research, Bureau of Mines, in the initial addresses at the symposium welcomed more than 140 representatives of industry, educational institutions, and government from 16 states, Canada, Great Britain, etc.

Jan 1, 1966

By S. Kodama

Starting on a small scale, the equipment for processing synthesis gas to form liquid hydrocarbons was expanded to handle 100 m) 3/hr. This reactor was successfully designed and constructed, and a basis for future design methods was established. Because, however, this work was carried out on an empirical basis, it is felt that a more thorough theoretical study should be made in an effort to increase the efficiency of the process, particularly in the development of a simpler converter.

Jan 1, 1951

By Charles M. McCulloch

This Bureau of Mines report discusses the principles of using computers to draw maps and plot geologic data of mining areas. The types of maps that can be drawn by a computer are reviewed, using as examples two separate areas where poor roof and gas emissions caused mining problems. Such maps can be used not only to help identify problem areas, but also to predict areas where problems could occur, thus giving mine operators time to work out solutions prior to mining. The average cost of a computer-drawn map for a mine property is less than $100, including computer time and man-hours for data preparation.

Jan 1, 1976

By Rita D. Sylvester

"IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January I, 1965, to December 31, 1969. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January I, 1960;' the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January I, 1960;3 the 5-year list of Bureau publications and articles from January I, 1960, to December 31, 1964.' It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1965, to December 31, 1968, as well as the Bureau publications and articles for 1969."

Jan 1, 1970

[ ]

Jan 1, 2011

By R. W. Van Dolah

An important function of stemming used to confine explosives in shot holes in underground coal mines is to minimize the chance of ignition of firedamp or coal dust by the detonation products. Until 1952, the Bureau of Mines approved only the use of fireclay or similar incombustible material for stemming permissible explosives. At least 2 feet of stemming were required except in holes less than 4 feet deep; in such short holes the stemming was required to be half the depth of the hole. Over the years, several special stemming devices have been proposed in the United States as substitutes for fireclay. Many economic and safety advantages were claimed for these devices, but only one approved device has been marketed in this country. Bureau requirements for stemming explosives in coal mines were modified at that time to permit the approved stemming device to be used as a substitute for the required fireclay.

Jan 1, 1961

By Charles L. Kimbell

In overall aggregate, the world&apos;s mineral industry in 1987 experienced a more satisfactory year than in 1986, at least insofar as its performance could be assessed from traditional statistical indicators. Production, trade and consumption seemingly advanced in the case of the majority of commodities, and prices for a number of commodities advanced. It was by no means certain, however, whether 1987 investment in mineral industry ventures would top the levels of 1986, when, in the case of petroleum industry investment expenditures there had been a sharp decline, this in contrast to evidences of a slight upturn in steel industry investment. World crude mineral output value was estimated at more than $1,084 billion, and the value added by minerals industry processing of this material probably raised the total value of the industry&apos;s production from primary materials to more than $2,600 billion constant 1983 dollars. Less easy too assess was the value of mineral commodities moving in international trade, but with a resurgence in oil prices from the 1986 levels, an increase above the 1986 $500 billion mark seemed assured. There are no comprehensive aggregate statistics on mineral consumption comparable to those on production and trade, but quantitative growth recorded for most major commodities suggested a favorable trend, particularly when coupled with a general (though by no means universal) upturn in unit prices.

Jan 1, 1989

By R. M. Strong, Lauson Stone

Under the terms of the act establishing the Bureau of Mines, this bureau was authorized to carryon the work of testing and analyzing fuels which had been conducted by the technologic branch of the United States Geological Survey. That work included in its scope an investigation of the availability and uses ofliquid as well as solid fuels, for the original outline of the fuel-testing investigations contemplated, as soon as the funds would be available, a study of the liquid-fuel resources of the country and the making of related researches to determine how these resources could be utilized with greatest efficiency. Owing to the fact that many difficulties were being encountered in the adaptation of the heavier fuel oils for convenient use in internalcombustion engines, it was deemed best to begin the investigation of liquid fuels with tests of gasoline, a fuel in more or less general use. When this investigation began, the extensive introduction, especially by foreign powers, of liquid fuels for small naval craft had awakened much interest. However, the quality of gasoline was reported to vary materially in different countries and the quantity available was said to be rapidly decreasing, with the probability of a prohibitive increase in price. At the same time the claim was made that denatured alcohol, of fairly uniform quality, could be procured in all parts of the world, that unlimited quantities could be readily produced at a low cost, and that this fuel could be used much more efficiently than gasoline in internal-combustion engines. Such statements naturally led to a widespread belief that the time was near at hand when denatured alcohol would entirely displace gasoline as engine fuel. Therefore, the first investigations of the liquid mineral fuels logically embraced a careful series of comparative tests of gasoline and denatured alcohol in engines. A series of over 2,000 such tests was conducted at the Government fuel-testing plants at St. Louis, Mo., and Norfolk, Va., details of which are given in the following pages. The report is published by the Bureau of Mines because of the transfer of the fuel-testing investigations to this bureau.

Jan 1, 1912

By W. B. Berwald

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gras association, has been studying actively for the past several years the problem of the flow of natural gas through high-pressure transmission lines. Numerous data on gas flow through pipe lines under many conditions of operation have been obtained by carefully conducted tests, and these data, together with all other available information, have been analyzed carefully to secure practical facts for the use of operators in designing pipe lines and determining the effects of different operating conditions on pipe-line capacities. The first procedure in initiating; this problem was to review, compile, and analyze all of the existing data on the flow of natural gas through pipe lines. Actual data applicable to pipe and operating conditions normally used in the transmission of natural gas were meager, and the several pipe line flow formulas developed by different investigators gave widely varying; results when applied to problems of pipe-line design. Therefore, further experimental work under conditions comparable to those found in transmitting natural gas was essential before any definite recommendations could be made.

Jan 1, 1931

By M. B. Boyer, C. H. Herty, F. A. Hartgen, G. L. Frear

"DEFINITION OF VISCOSITYViscosity has been defined as the resistance experienced by one portion of a liquid moving over another portion, such as one molecular plane moving over an adjacent plane. A measure of viscosity is the force required to keep one plane in motion at Unit velocity, the other plane being considered stationary. Figure 1 illustrates the general idea that the surface friction between two adjacent areas will be greater the larger the molecules. Therefore it may be assumed that viscosity will be increased by molecular association or agglomeration, and likewise dissociation rill decrease viscosity. According to Maxwell (1)6 the unit of viscosity, the poise, is the tangential force per square centimeter of area of either of two horizontal planes 1 centimeter apart, one of which is fixed while the other moves with unit velocity, the space between being filled with viscous liquid of unit viscosity.The need for a satisfactory apparatus and experimental procedure for the determination of viscosity of high-melting materials at temperatures corresponding to those in pig-iron and steel making has been recognized during the past few decades. The condition of the slag during the smelting and refining periods in the iron- and steel-making processes exerts an important influence on the metal product obtained, this slag condition really meaning the state of viscosity or, vice versa, fluidity, which the slag attains under certain conditions."

Jun 1, 1934

By Edmund S. Leaver, A. P. Towne, Jesse A. Woolf

Part of the work of the Precious Metals Section is to conduct oretesting experiments on ores selected as representative of various mining districts or areas . The projects are authorized by the Metallurgical Division , and only those ores in which gold and silver or gold or silver constitute an essential part of the total values are assigned to the Precious Metals Section . Such ores include those containing the precious metals only as commercially important ingredients , as well as those containing base metals such as copper , lead , and zinc along with the gold and silver . In many instances the "ore " may be a tailing product of a grade good enough to warrant retreatment , or a concentrate for which it is desirable to develop a method of treatment to avoid the expense of shipment to a smelter . It is evident that in general the greater part of this ore - testing work is done according to standard testing procedure , such as cyanidation, amalgamation, gravity - concentration , and flotation , or a combination of these methods . The standard methods of conducting such tests have been outlined in previous reports of ore - testing studies . However , since the inauguration of this oretesting program 6 years ago , the ores submitted under authorization have become increasingly more refractory to simple methods of treatment. Consequently, a considerable number of the projects completed during the fiscal year 1941 have required an unusual amount of work and in some instances have developed into real research problems . For such ores more complete microscopic and spectroscopic examinations and more complete chemical analyses

Feb 1, 1942

By G. A. Smyres

The Bureau of Mines investigated a HCI-02 leaching procedure to recover Cu, Ni, and Co from a low-grade bulk sulfide flotation concentrate prepared from the Duluth gabbro complex. Since the Duluth gabbro complex is the largest known and unexploited Ni resource in the United States, the development of options for extracting the metal values from the flotation concentrate of this domestic resource is necessary. Conditions were determined for producing a pregnant solution low in Fe to facilitate recovery of the metal values. Leaching experiments were conducted at 15 pct solids, 1000 to 1200 C, 0.2 to 0.3 g HCI per gram concentrate in a 50-gal reactor pressurized to 50 pSig with 02. Base metal extractions from the concentrate were, in percent, 90 to 92 Cu, 99 Ni, 97 to 99 Co, and 0.1 .Fe. Precious metals extractions were erratic and unpredictable; at best their extractions were, in percent, 55 Au, 90 Ag, 40 Pt, and 45 Pd. The reaction time at 1200 C was 0.5 h. The use of compressed air instead of 02 as the oxidant was also investigated. Solvent extraction using LIX 622 was used to remove Cu from the pregnant solution. Cementation on Cu was tested for precious metals recovery, while sulfide precipitation was used to produce a Ni-Co product. A conceptual flowsheet for treating the Duluth gabbro concentrate is proposed.

Jan 1, 1985