Search Documents

Empirical methods involve the scientific interpretation of real-world experience. Many problems in ground control lend themselves to an empirical approach because the mines provide us with plenty of experience with full-scale rock structures. During the past 10 years, powerful design techniques have emerged from statistical analyses of large databases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. In the process, our practical understanding of pillar behavior has been greatly enriched.

Jan 5, 1999

By L. W. Kelly

The primary purpose of this paper is to show the appreciable savings that were made by roof-bolting the main west entry of the Kings mine, which was to be the permanent, main haulage road, as compared to the cost of supporting the same roof with peg timbering as first planned. Additional items that might prove valuable to other mine operators are contained in this paper and detailed below. 1. A detailed cost of the system of roof support known locally as the peg-timbering method is given. It consists fundamentally of supporting steel cross bars on pegs inserted into holes drilled in the ribs close to the roof. 2. A method of supporting the roof in caved entries is shown, where such support must endure for an extended period in haulageways and air courses.

Jan 1, 1952

By A. W. Deurbrouck

This report describes the washability characteristics of 18 coal samples taken from 11 drill hole cores from the San Juan Basin area of New Mexico and Colorado. The ash content of these coals could generally be substantially reduced by removing the heavy impurities. The coals were characteristically low in sulfur content; only one sample contained more than 1 percent sulfur after removing the sink-I.50 specific gravity material. The coals ranged in rank from subbituminous C to high volatile C; 11 of the samples were subbituminous A. Many of these core samples came from areas where very little fieldwork has been done; consequently, an outgrowth of this work has been an increase in known coal reserves of the San Juan Basin area.

Jan 1, 1972

By T. M. Romslo

The Lake Shore property, located in the early 1880's, contains copper-bearing deposits that have been developed by surface excavations, underground workings, and churn-drill holes. Operation of the property ended in 1929 with a total recorded production of 280,000 pounds of copper. The property is near the foot of the Slate Mountains, which are made up mainly of probably the Pinal formation of pre-Cambrian age. In the mine area there are a few outcrops of granite, which is exposed over a large area east of the property. Other outcropping rocks on the property are limestone, quartzite, and diabase. The limestone and quartzite probably are the Mescal and Troy formations of pre-Cambrian and Cambrian age, respectively. The predominant copper mineral is chrysocolla, a hydrous silicate that occurs mainly as fracture filling in bedded schist. It is also, the principal copper mineral in the shear zone at the schist-granite contact and in limestone southeast of the main workings. Investigation of the Lake Shore property by the Bureau of Mines included both topographic and geologic mapping, exploratory drilling, and metallurgical test work. One diamond-drill, hole and five churn-drill holes were completed for a total of 2,872.5 feet. Drilling started January 19 and was completed May 13, 1949.

Jan 1, 1950

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986

By Timothy W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (?water box?) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 percent reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2010

By J. B. Janus

In connection with the purchase of coal under specifications for Government use, the Bureau of Mines in this report has compiled data on 81 mines located in 15 States. This annual report lists analytical data on the composition and quality of tipple and delivered samples of coal collected during fiscal year 1973. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. Ultimate analyses are given for most of the coalbeds listed. The deliveries were sampled at destination in accordance with instructions issued by the Bureau of Mines. All samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1973

By William E. Young

There are many large rhodunite-bearing veins containing manganese in the Eureka-Animas Forks area of the San Juan Mountains in Colorado. The Sunnyside vein is the largest known vein in the area. As observed on the surface, the vein is mineralized over 8,000 feet and attains a maximum width of 200 feet. The average width of the vein and its branches and ramifications is 58 feet in the area that was mapped in detail. The weighted-average analysis of surface and underground samples from the northeastern extension of the Sunnyside vein is 8 percent manganese. Most other known veins in the area have a similar manganese content. The Hidden Treasure vein lies southeast of the Sunnyside-No Name-Mastadon vein. The weighted average of the analyses of surface and underground samples from this vein is 13 percent manganese. Exposures of the Scotia-Silver Chord vein are visible over a strike length of 4,000 feet on Treasure Mountain. Diamond-drill holes show that the vein contains 10 percent or more manganese to a depth of 400 feet. The vein has an average width of 28 feet. The Independence vein is exposed on the surface for a distance of 600 feet and has an average width of 6 feet. Three cut samples taken across the vein had an average content of 20.7 percent manganese. Sampling of the outcrops of eight veins in the Placer Gulch area also indicates manganese. Numerous other veins cropping out in the surrounding area are similar to the outcrop of the. Sunnyside vein system mineralogically and are worth investigating.

Jan 1, 1966

Bag stackers who use semi-automated palletizing machines and air slides may be exposed to high concentrations of dust. To reduce dust exposure, use an exhaust ventilation system in conjunction with an envelope of clean air over the bagstacker provided by an overhead air supply. Description of Hazard Mineral processing plants in the United States and throughout the world process material that is finely ground and placed into bags for shipping to the consumer. These bags normally range from 50 to 100 pounds in weight. Once the material is placed in these bags, a bag stacker loads the bags onto pallets. A bag stacker is exposed to a lot of dust that is mainly released by the force from loading the bag onto the pallet. The two main sources are the dust on the outside of the bag and the dust that escapes from inside the bag as it is loaded. The Mine Safety and Health Administration's (MSHA) records indicate the bag stacker's dust exposure is one of the highest of all workers at mineral processing operations. Ways to reduce the dust exposure and strain to the bag stacker are in constant development. Recently, automated systems have been built. These systems range from fully automated, which totally remove the worker from the bag-stacking process, to semiautomated systems, in which the bag stacker still performs some of the functions. This Hazard Control deals with controlling the bag stacker's dust exposure during use of a semi-automated palletizing machine. The worker slides the bags into position on the palletizing machine. Once an entire layer of bags is positioned, the bag stacker operates the controls on the palletizing machine to lower the layer of bags onto the pallet. An air slide is built into the semi-automated palletizing machine so the bags are easier to move. This slide uses a metal table with air jets that exit through small holes at high velocities, similar to an air hockey game. The dust problem occurs because the air slide causes dust to blow up onto the bag stacker, significantly increasing the dust exposure.

Jan 7, 2001

By Douglas Ketcham, Thomas Jetzer

While the neurological and vascular aspects of Hand-Arm Vibration Syndrome (HAVS) has been generally accepted as a medical condition, the medical criteria and the clinical findings used to establish the diagnosis has been more difficult to bring to consensus. The criteria was first quantified by the Taylor-Palmear scale.1 This criteria was subsequently modified in 1986 at the 1st Stockholm Workshop2,3 to included more acceptance for the neurological effects that characterized the predominate findings in some workers. The relationship between hand-arm vibration and Carpal Tunnel Syndrome was defined in NIOSH 97-1414. While the aforementioned documents have defined the clinical entities associated with hand-arm vibration exposure, agreement on the clinical findings and test to confirm the diagnosis has be been more difficult to bring to consensus. Clinicians assessing HAVS has relied on a number of varied neurological and vascular tests. The neurological testing has focused on assessing damage to the sensory capability of the fingers for the neurological component including tests to measuring ability to sense vibration, cold or other end point finger sensor functions. However, the vascular testing has been traditionally focused on the ability to either measure vascular function or to reproduce the vascular blanching that occurs in HAVS with cold water provocation. Recent assessment of this testing in the United Kingdom Coal Miner’s study has questioned the value of this testing especially in reviews by McGeoch.5 In an attempt to provide some type of definitive testing to substantiate vascular damage from hand-arm vibration exposure, angiography is an alternative or adjunct to cold water provocation testing. The standards that have been established to predict the level, type and incidence of HAVS have been based on clinical studies and reports that have essentially been all male populations. However, the recent entry of women into more vibration intensive jobs has brought about the exposure of some women to high levels of vibration previously only previously experienced by men. However, there have been only few studies that look at HAVS in women6. Although exposed the same vibration levels, it has not been clear that the latency and type of pathology of HAVS in women will be the same as for men. The purpose of this study is to look at recent case studies of men and women exposed to jobs with high levels of hand-arm vibration with extensive clinical testing for both the neurological and vascular components of HAVS as well as other associated upper extremity conditions such as Carpal Tunnel Syndrome.

Jan 6, 2006

By Hideo Ando, Yuka Satou, Tatsuya Ishitake

Whole-body vibration occurs when the body is supported on a surface which is vibrating. Occupational exposures to whole-body vibration mainly occurs in the transportation industry, but also in association with other industrial process. Epidemiological studies have frequently indicated an elevated health risk for the spine in workers exposed to whole-body vibration. With regarding to train or bus operators, a fall of drivers’ wakefulness level because of fatigue is often pointed out. This decrease in wakefulness results in an increase of the occurrence of accidents. However, a study of how whole-body vibration affects people's level of wakefulness has not been done. To test the hypothesis that exposure to whole-body vibration has a certain effects on level of wakefulness, the change of a subjective wakefulness level and changes of electroencephalogram (EEG) were observed under experimental exposure to short-term whole-body vibration. Methods Subjects are ten healthy male university students, with an average age of 20.7 ± 1.8 years old, and they are all nonsmokers. Using the equipment (CV-300, AKASHI) of whole-body vibration generator, we consider an exposure environment of actual driver work, so that set the frequency and the acceleration level as 10 Hz and 0.6ms-2 r.m.s.. The subjects were exposed to whole-body vibration in the seated position and exposure time was fixed for 12 minutes. Subjective wakefulness level was evaluated using the questionnaire of VASS (Visual Analog Sleepiness Scale) and KSS (The Kwansei Gakuin Sleepiness Scale). For the electroencephalogram (EEG) measurement, it was equipped with the electrodes based on the International ten-twenty electrode system (C3-A2, O1-A2, O2-A1). EEG activity in the alpha frequency band (8 – 12 Hz) is one of the most typical physiological indicator which represent the transition from wakefulness to sleepiness. AAT (Alpha Attenuation Test) which repeats three times each opened and closed eye for 1 minute was performed in a seating position with directions of the researcher in the beginning, in the middle and in the end of exposure to whole-body vibration. For analysis, power spectral analysis was conducted over the last 6 min of EEG, and wakefulness levels were defined as the ratio of mean alpha power during eyes closed versus eyes opened. The laboratory was kept at room temperature (21 ± 1.0 degrees C), humidity was 50 ± 5%, noise level was 63.6 dB (A) eq, and illumination 510 lx. Each experiment was started around 10:00 am to minimize the effect of biorhythm.

Jan 6, 2006

By W. L. Staker

The Bureau of Mines investigated the use of shredded automobile scrap for copper cementation. Air agitation was used to improve the cementation rate and prevent excessive buildup of copper on the iron. The pieces of scrap were too large to be properly evaluated in the laboratory; therefore, a pilot scale test unit was constructed and the process tested at field locations. Pregnant solution was obtained from industrial leaching operations, processed in the test unit and the barren solution and cement copper were returned to the plant process stream. The test results showed that the air-agitated launder containing auto-mobile scrap was an effective means for recovering copper from leach solutions. A continuous l4-day test run was made without a noticeable decrease in cementation efficiency. The most suitable scrap product was obtained from incinerated automobile hulks shredded in a hammer type of shredder. However, it was necessary to remove small pieces such as nuts and bolts because they interfered with the discharge of the copper product.

Jan 1, 1976

By E. K. Kleespies

The Bureau of Mines demonstrated a technique for electrowinning titanium from titanium nitride and titanium dioxide. Titanium-nickel-copper metal solutions containing 26 to 61 weight-percent titanium were prepared by electrolyzing titanium nitride in molten mixtures of potassium fluotitanate) and sodium chloride or barium chloride and depositing titanium on nickel-copper cathodes. A titanium-nickel alloy was prepared by electrolyzing titanium dioxide in an electrolyte of potassium fluotitanate) sodium fluoride) and calcium fluoride and depositing titanium on solid nickel cathodes. This alloy contained 21 weight-percent titanium and had a combined oxygen-carbon content of less than 0.1 weight-percent. A compartmented cell confined the oxide feed near the anode and inhibited oxygen contamination of the metal.

Jan 1, 1966

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines developed induction slag melting process is of concern to members of the titanium industry. The objective of the research was to determine the effect of CaF2 inclusions on the properties of titanium and its survival rate during melting. The data were obtained from single induction-slag-melted ingots prepared with the normal addition of 4 pct and also with 2- and 1-pct additions of CaF2 slag. The results of this effort showed that the mechanical properties of single-induction-slag-melted Ti-6Al-4V alloy exceed the minimum values specified in Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H, but these materials are much more notch sensitive in fatigue than normal Ti-6A1-4V alloy titanium. First and second vacuum-arc remelts of single-induction-slag-melted ingots fragmented and increased the number of inclusions, while reductions in the amount of flux resulted in an upward trend in the spatial distance between pores in an x-y plane.

Jan 1, 1988

By Leon E. Esparza

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 16,927-acre Pryor Mountain Wilderness Study Area (MT-067-206), part of the 3,955-acre Burnt Timber Canyon Wilderness Study Area (MT-067-205), and part of the 4,550-acre Big Horn Tack-On Wilderness Study Area (MT-067-207) to evaluate their identified mineral resources. The Burnt Timber and Big Horn Tack-On study areas contain 3,430 and 2,550 acres, respectively. The three areas are in Carbon County, MT, and Big Horn County, WY, about 13 miles north of Lovell, WY. No identified resources exist in any of the study areas. Bureau of Mines personnel reviewed literature, searched county mining records and examined prospects, claims, and mineralized areas to determine whether identified mineral resources existed. The three study areas are within the Pryor Mountain unorganized mining district. U.S. Department of Energy production records indicate there were 223,000 pounds of uranium oxide (U308) and 236,000 pounds of vanadium pentoxide (V205) produced from 19 properties within the mining district. The average ore grade was 0.36 percent [3,600 ppm (parts per million)] U308 and 0.416 percent (4,160 ppm) V20S. Only the Pryor Mountain study area has current claims, the 50 claims of the S0S group.

Jan 1, 1986

By Winthrop F. Watts

The U.S. Bureau of Mines evaluated the performance of a catalyzed diesel particulate filter (CDPF) and a CDPF combined with a diesel oxidation catalyst (DOC) at two metal mines. This report describes the results from the two field evaluations. The CDPF-DOC was installed on a load-haul-dump (LHD) powered by a 175-kW, prechambered, turbocharged engine. This system reduced diesel particulate matter (DPM) concentrations by 71±28 pet, as determined by size-selective sampling with gravimetric analysis, and by 71±29 pet, as determined by respirable combustible dust (RCD) analysis at the vehicle operator's location. The CDPF was installed on a diesel-hydraulic, roof-bolting jumbo, powered by a 172-kW engine. The CDPF reduced DPM concentrations by 72±21 pet, as determined by size-selective sampling with gravimetric analysis, and by 62±25 pet, as determined by RCD analysis at the vehicle operator's location. Underground evaluation was more difficult because of frequent movement by the roof-bolting jumbo, variation in daily workload, tremendous fluctuation in ventilation airflow rates, and use of a high sulfur diesel fuel, which promotes the formation of sulfate particles, decreases filtration efficiency, and hastens the deterioration of the catalyst.

Jan 1, 2010

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1983 was $361.3 million, an increase of $61.9 million over that of 1982. The increase reversed a downward trend that started in 1980 and established a new record high for value of nonfuel minerals in the State. Output of most nonfuel minerals increased to some degree with unit value increases creating the record-high value year. Cement, clays, lime, sand and gravel, and crushed stone were the major commodities produced in Alabama. Alabama led the Nation in the production of crushed marble; was second in bauxite; fourth in ferroalloys, dimension marble, common clay, and fire clay; fifth in bentonite and kaolin; and sixth in masonry cement and lime.

Jan 1, 1985

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930

By J. W. Paul

This circular is one of a series of reports on coal mining methods and cost s which are being prepared by the U. S. Bureau of Mines for the purpose of making available to those interested in the industry a knowledge of the mining methods employed in mines where mechanical and hand loading is practiced and the cost data on the several operations pertaining to the removal of coal from the working faces and its transportation to the tipple for loading into railroad cars. The methods employed are influenced by the natural local conditions with respect to the thickness and character of the coal beds and the overlying strata, the means employed for roof support and its control, and the disadvantages incident to the development of mines in thin coal beds.

Jan 1, 1929

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006