Search Documents

By Paul Wellman

A computer program is presented that may be used to calculate the bare equipment cost of the major processing units for any hot potassium carbonate gas purification system. The program is designed such that, with only minor modifications, it could be used with a variety of computer systems.

Jan 1, 1968

By D. W. Mitchell

This Bureau of Mines report summarizes experience and past research on methods for sealing abandoned areas of a coal mine and areas from which the pillars have been wholly or partially extracted. The Federal Coal Mine Health and Safety Act of 1969 requires that such areas be ventilated or sealed with explosion-proof bulkheads, but the present study indicates that bulkheads alone cannot isolate areas in a coal mine in which methane and other dangerous gases have accumulated. Gas-air exchanges between sealed and open areas must be controlled.

Jan 1, 1971

By J. V. Batty

Radioisotopes of selenium (se78) and tellurium (Te123) were successfully employed by the Bureau of Mines as tracers in metallurgical research directed to developing improved methods for volatilizing these elements from low-tenor raw materials. Prior research, guided and controlled by conventional analytical methods, was seriously hampered by inconsistent selenium and tellurium analyses, by the slowness of the conventional chemical methods, and by the poor accountability of these volatile elements in test products. Methods were devised and evaluated for admixing the radioactive tracer with typical raw materials and then following the deportment of the selenium and tellurium by radiometric methods with occasional chemical analysis checks. These techniques were found unusually effective in (1) quantifying the completeness and the rate of volatilization of selenium and tellurium while heating the raw materials at different rates to different temperatures and (2) accurately tracing and quantifying the distribution of minute amounts of these volatile elements in the several products made by high-temperature treatment and in the several units comprising the experimental equipment.

Jan 1, 1962

By E. R. Bauer

This report presents the results of a cooperative study between BethEnergy Mines Inc., Ebensburg, PA, a central Pennsylvania coal mining company, and the U.S. Bureau of Mines to investigate longwall development entry roof instability. In-mine mapping of geologic and deformational features was conducted to reveal the major ground control problems encountered during gate road development. In addition, mining-induced pillar load monitoring was used to indicate development loading on variously dimensioned gate road pillars and to determine if pillar yielding occurred. Finally, visual observations of a variety of roof control methods were used to determine the most effective support elements for controlling cutter roof failure.

Jan 1, 1992

By H. Polat, Q. Hu, M. Polat, S. Chander

"The electrostatic charge on spray droplets of ionic surfactant solutions and coal particles was measured and the results were correlated with the dust collection efficiency. When various surfactant were added, the magnitude of the droplet charge increased significantly and it was observed to be a function of surfactant type and concentration. The concentration of maximum droplet charge coincided with surfactant concentration where maximum collection efficiency was observed for these surfactants. Particles of coal also carried substantial amount of charge magnitude of which seemed to be a function of coal rank.Based on the results presented in this paper, it was concluded that ionic surfactant primarily act as a strong electrostatic charge inducer for droplets. Due to interactions between these highly charged droplets and naturally charged particles, the efficiency of droplet-particle collisions play a primary role when compared to the wetting and engulfment phenomenon which could only follow a successful collision. INTRODUCTIONWater spray are widely used to suppress airborne dust in mine atmospheres (Walton and Woolcock, 1960; Kobrick, 1970; Hamilton, 1974; Jayaraman et al., 1986). Several investigators have considered the use of surfactants to enhance the effectiveness of water sprays especially for difficult to wet particles such as those of coal (Glanville and Wightman, 1979). The capture of dust particles by water droplets involves droplet-particle collisions, adhesion of particles to droplets, and engulfment of particles into droplets. Surfactants affect these sub processes through their influence on droplet charge, surface tension, and wetting. The last two mechanism have been thoroughly studied in recent years (Walker et al., 1952; Cohen and Rosen, 1981; Glenville and Haley, 1982; Chander et al., 1988; 1991). However, little attention has been paid to the role of electrical charge on particles and droplets on the collision and adhesion of spray droplets and dust particles."

Nov 1, 1995

Bitumninous and semianthracite coal reserves underlie about 1,400 square miles of Arkansas, less than 2.7 percent of the state's total area. These deposits, located near the western border, contain an estimated 2.2 billion tons, of which about half are recoverable. This represents less than one-tenth of one percent of the national reserves. Most of the commercial coal is mined from thin beds that are at least 14 inches thick. In some locations, however, the coal beds can be as much as eight feet thick. Lignite was mined in southern Arkansas before the Civil War. Current estimates indicate that the reserves may be as high as 9 billion tons, which could be used in the state's coal-fired electric generating plants; however, these deposits are not being mined at present. Because many coal operations in Arkansas are small and the demand for coal is unsteady, the industry employs fewer than 25 miners on a daily basis. Arkansas gained primacy when its regulatory program was conditionally approved November 21,1980, subject to the correction of four minor program deficiencies. The regulatory program was fully approved January 22, 1982. Authority of the state to administer its Abandoned Mine Land Reclamation Program was granted upon approval of the Arkansas Reclamation Plan on May 2, 1983. Arkansas was the first state to assume responsibility for abandoned mine land emergency projects when its Reclamation Plan was approved.

Jan 1, 1992

By David A. Lipton

In the summer of 1985, at the request of the U.S. Forest Service, the U.5. Bureau of Mines examined the 109,000-acre West Big Hole study area to evaluate its identified mineral resources. The study area is in Beaverhead County, about 50 mi west of Dillon, MT. Four lode properties within or adjacent to the study area contain an estimated 452,000 tons of identified subeconomic gold-silver resources. Resources ranged from 900 to 302,000 tons, with estimated grades between 0.02 and 0.23 oz/ton gold and as much as 4.8 oz/ton silver. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that exploration may identify resources on 18 additional lode properties within the study area and 5 properties adjacent to it.

Jan 1, 1988

By W. A. Cole

As the mines get older and the active workings get Farther and farther away from the original mine openings, it becomes increasingly difficult and expensive to ventilate most coal-mines properly. At the same time, the avenues of escape for those employed underground have become so extended' as often to make it impossible for them to make their way out of the mine in the event of a fire, mine explosion, or other emergency. Where such Conditions exist, the only satisfactory solution is to make new ventilation and emergency-escape openings near the active mine workings. At most mines this would necessitate sinking shafts, which is often slow and expensive.

Jan 1, 1945

By Gerrit V. R. Goodman

A laboratory study assessed the impacts of water spray pressure, face ventilation quantity, and line brattice setback distance on respirable dust and SF6 tracer gas concentrations around a continuous mining machine using a sprayfan or directional spray system. Dust levels were measured at locations representing the mining machine operator and the standard and off-standard shuttle car operators, and in the return airway. The results showed that changes in all three independent variables significantly affected log-transformed dust levels at the three operator sampling locations. Changes in setback distance impacted return airway dust levels. Laboratory testing also identified numerous variable interactions affecting dust levels. Tracer gas levels were measured on the left and right sides of the cutting drum and in the return. Untransformed gas levels around the cutting drum were significantly affected by changes in water pressure, face ventilation quantity, and setback distance. Only a few interactions were identified that significantly affected these concentrations. Gas levels in the return airway were grouped by face ventilation quantity. Return gas levels measured at the low curtain quantity were generally unaffected by changes in water pressure or curtain setback distance. At the high curtain quantity, return airway gas levels were affected by curtain setback distance. A field study was conducted to assess the impact of these parameters in an actual mining operation. These data showed that respirable dust levels may have been impacted by a change in water pressure and, to a lesser extent, by an increase in curtain setback distance. A series of tracer gas pulse tests were also conducted during this study. The results showed that effectiveness of the face ventilation was impacted by changes in curtain flow quantity and setback distance. Laboratory testing supported similar conclusions.

Jan 1, 2004

By Howard P. Hamlin, John W. Sweeney

Shales , clays , and loess in Iowa were tested and evaluated to determine feasibility of producing lightweight aggregate by commercial rotary - kiln or sintering methods . Preliminary testing was conducted in a muffle furnace . Rotary - kiln tests were conducted in a 16 - inch by 14 - foot rotary kiln . Concrete cylinders and cubes were tested to determine qualities of the aggregate . Three samples made suitable lightweight aggregate by rotary - kiln methods and two by sintering .

Jan 1, 1964

By Don Conrad, Tom Friend, Bill Wiehagen, Lynn Rethi

On-the-job training (OJT) is a very common method of teaching job skills. Much of the training is done by experienced workers. This paper discusses small investments that can help improve the effectiveness of OJT. Effective OJT involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the OJT trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. The scope of this paper addresses (1) organizational considerations supporting structured OJT, (2) general strategies for structuring OJT, (3) a typical approach for conducting OJT, (4) characteristics and duties of OJT trainers, and (5) limitations of OJT as a teaching method. Health, safety, and operational skills can be connected through training. Haul truck operator training is used to illustrate some of the concepts discussed in this paper.

Jan 1, 2002

By R. Barany

In this paper, closed expressions have been obtained for the frequency spectrum of a Born-Karman square lattice in terms of elliptic and hyperelliptic integrals. This work is part of continuing research by the Bureau of Mines with the thermodynamic properties of metals and minerals. Although other workers have obtained various types of approximations for the general case of the frequency spectrum of a square lattice, no one previously has obtained closed analytic expressions for this spectrum. To understand the optical and thermodynamic properties of crystals, several investigators have studied the distribution of frequencies of normal modes of vibration of the crystal lattice. Born and Karman3 laid the foundation for the theory of lattice dynamics and obtained detailed results for the case of a one-dimensional lattice. Blackman4 used numerical techniques to estimate the frequency distribution of a two-dimensional square lattice. Mbntroll5 analytically determined the frequency distribution of a square lattice for a particular value of the force constants. He also studied the more general problem and obtained some analytic approximations, using the method of moments. However, the calculations by this method were so difficult that it was not always practicable to carry them out. Van Hove6 and Montroll7 studied the nature of the singularities in the frequency spectrum of both a two and

Jan 1, 1962

Continuously monitor and record respirable dust levels underground by a reliable, sensitive, and fast-response device. Approach A light-scattering photometer, having a LED (Light Emitting Diode) light source and other significant improvements, has been designed and incorporated into a portable continuous monitor. How It Works The monitor continuously draws air into the sampling inlet through a cyclone that removes dust particles larger than respirable size. The dusty air enters the photometer vertically downward through a cylinder which is intersected by the optical system. (This cylinder appears as a circle in the drawing of the photometer.) The center of he column of dusty air intersects a beam of pulsing light from the LED, causing some of the light to be reflected, scattered, and refracted. Only the light that is scattered at an angle of about 700 from the light beam passes through a lens to the photodetector which generates an output voltage Signal proportional to the dust content in the air. This signal is detected, amplified, and converted to a digital readout directly in milligrams of dust per

Jan 1, 1979

By Michael S. Miller

In 1986 and 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 550-acre Carson-Iceberg Wilderness Study Area (NV-030-532), in order to evaluate its identified mineral resources. The Wilderness Study Area is located in Alpine County, CA, 11 mi southeast of Markleeville, CA. Tertiary volcanic and granitic rocks, as well as alluvium, underlie the area. Hydrothermal alteration and faulting have affected some rocks; argillic, silicic, and limonitic alteration are found, particularly near faults. No mineral resources were identified in the Wilderness Study Area. The area has one small pit and no mines or claims. Samples from the Wilderness Study Area and vicinity contained uneconomic amounts of gold, silver, copper, lead, zinc, mercury, arsenic, and molybdenum. Mineral occurrences are too small and low grade to be of interest within the foreseeable future.

Jan 1, 1988

By S. H. Lorain

The Minah silver-lead mine in the Wickes district, Jefferson County, Mont., produced substantial quantities of silver-lead ores in the 1890's. The mine has been abandoned since the "silver panic" of the early 1900's. As a part of the Bureau of Mines: program to develop new sources of lead to overcome the growing shortages of that metal, a development project was started at the Minh mine in April 1946 and continued until June 1947, during which 5,600 feet of angledozer trenching and. 1,093 feet of core drilling were completed on the main vein and nearby parallel veins: As a result of this work, interest in the property was stimulated and private operators are now engaged in reopening the mine. This report discusses the past history, geologic setting, and the recent and early operations of the mine.

Jan 1, 1948

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By S. A. N. Sheya

The U.S. Bureau of Mines performed batch equilibrium contact experiments to examine the ability of activated coconut-shell carbon to adsorb various metal cyanide complexes. Tests were also conducted to determine the effect these cyanide complex impurities might have on the adsorption of gold by the activated carbon. Metal cyanide species included in the investigation were antimony, arsenic, cadmium, calcium, cobalt, gold, iron, mercury, nickel, silver, thallium, and zinc. Tests were made over a pH range of 6.4 to 12.5. The carbon exhibited a preference for gold adsorption over other metals present in solution. In the absence of gold, the metal cyanide complexes were adsorbed; adsorption generally decreased with increasing pH. However, calcium and thallium adsorptions increased with increasing pH, while arsenic and iron were not adsorbed at any pH.

Jan 1, 1989

By D. E. Pollock, T. W. Beck, J. A. Organiscak

This work presents the findings from a number of NIOSH studies evaluating the impacts of emerging technologies that may reduce dust exposures for continuous mining and roof bolting personnel. These technologies include use of a wet head cutting drum on a continuous mining machine that places water sprays on the cutting drum instead of placing them on a manifold outby the drum. Evaluations at two separate operations showed that the use of the wet head sprays reduced dust levels at the miner operator in the return air, although these reductions were quite variable. NIOSH also assessed the effectiveness of a canopy air curtain for protecting roof bolting personnel. The data showed that dust levels were lower beneath the air curtain than outside the air curtain. This study also suggested several future modifications to the air curtain to in-crease its effectiveness. Finally, NIOSH evaluated mist drilling technology for its effectiveness in controlling respirable dust exposures of bolting personnel. A recent study showed that higher dust levels existed around a machine using the mist system compared to a machine using a conventional vacuum system for dust control. Unfortunately, the true impact of mist drilling was confounded by this machine operating downwind of the continuous miner for much of the study.

By Ch. D. Taylor

Past studies with blowing face ventilation systems have shown that using a machine-mounted scrubber and water sprays can reduced methane levels at the face. The current research was conducted to determine how the sprays and scrubber interact to reduce methane levels, and what spray configurations provide the best face ventilation when used with a scrubber. Testing was conducted in a ventilation test gallery designed to simulate a full-scale mine entry. In the entry, a model mining machine, equipped with a simulated dust scrubber and water spray systems, was located at the face of a 6.1 m (20 ft) box cut. Face ventilation was provided by a blowing curtain located 12.2 m (40 ft) from the face. Methane released from a manifold at the face was measured at six locations near the face to compare the ventilation effectiveness of the spray systems while operating with and without the scrubber. Airflow movement across the face was affected by the spray configuration and scrubber operation. Average face concentrations were lowest when directed sprays were used with the scrubber. Varying the direction of the scrubber exhaust affected face methane levels.

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60 percent and 40 percent, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert, and a rigid insert for cleaning the roof bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the coveralls when using either of the inserts.