Search Documents

By Lloyd Williams

1. The investigation shows that the Wilder (locally known as the Bon Air No. 2) is the only known bed of commercial importance in Putnam County, although at least 5 coal horizons are known. All of the coal production now reported comes from this bed, which is found In a basin with no known coal outcrops. Further drilling in the east end of the basin should disclose the location of the eastern end of the axial trough and the lateral extent of the basin in Putnam County and adjoining areas in Cumberland County. Continuity of this deposit with that in the area in Putnam County north of Monterey is not conclusively established but may exist. 2 Known (measured plus indicated) reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot in place, are estimated at 29 million tons, as of January 1, 1953. Of this total, 28 million tons are in beds 28 inches and more thick. All born coal reserves in Putnam County me under less than 400 feet of overburden.

Jan 1, 1954

By Terry G. Montgomery, Eric S. Weiss, John E. Going, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike I m3 chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.

By Avery H. Reed

RECORD production of cement, clays, salt, sand and gravel, and stone highlighted the mineral industry of the State in 1956. Coal and iron-ore production declined owing to increased imports of foreign iron ore and decreased demand for metallurgical coke. Alabama ranked second in production of bauxite and of native asphalt, and third in output of iron ore. New developments in the State included the Citronelle oilfield and its 97 wells, which more than doubled the total production of petroleum compared with 1955. There is no question about the impetus that field has given to the oil and gas industry in Alabama, now 13 years old. The State's 4 oilfields are in southwest Alabama and its 1 gasfield is in Marion County, in the Warrior coal basin.

Jan 1, 1958

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

By D. R. Dolinar, A. T. Iannacchione

Limestone formations in the United States can be subject to relatively high horizontal stresses owing to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rock fall hazard. Rock falls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings has an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orienting the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and off-setting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

By C. M. McKinney

The Bureau of Mines analyzed 626 crude oils from 546 oilfields in the United States that produced 2,500 BOPD or more during at least 1 of the last 3 years. Included also are crude oil analyses from eight fields that produced less but which were located in areas having few or no fields that produced 2,500 BOPD. The tables show the geographical and geological source, general characteristics. and determined and computed analytical data for each sample. The analyses were made according to the Bureau of Mines routine method and are directly comparable to other previously published analyses.

Jan 1, 1966

By J. Chilton

The fact that methane ignitions continue to occur at the mining face indicates that monitoring with machine-mounted methanometers does not always indicate the presence of high methane concentrations. Methane concentrations at the face change quickly due to changes in airflow. By measuring these changes in airflow, it may be possible to predict changes in face methane levels more quickly. Currently there are no techniques or instruments to accurately measure airflow in by the mouth of the ventilation curtain or tubing. Tests conducted in the NIOSH ventilation test gallery compare the data provided by one-, two-, and three-axis ultrasonic anemometers. The effects of changes in airflow direction and turbulence on instrument readings are discussed, and guidelines are given for selecting the type of instruments to be used for monitoring airflow near the mining face.

By Thomas O. Glover

The mining industry of Cameroon continued to be dominated by crude petroleum. Crude petroleum production has become the most important facet of Cameroon's economic development. Oil production was estimated to be 6.3 million tons in 1983 compared with 5.2 million tons in 1982 and 4.3 million tons in 1981. Over two-thirds of its export income was attributed to crude oil. The country's only refinery, dedicated in 1981, has a production capacity of 2 million tons. Cameroon has become self- sufficient in petroleum products since commissioning the refinery. The oil sector contributed approximately 13.5% to Cameroon's gross domestic product in 1982-83. Oil production was expected to rise from 125,000 barrels per day in 1983 to 156,000 barrels per day in 1985 when output peaks. Cameroon's ultimate recoverable reserves have been calculated at 100 million tons, or 750 million barrels of oil.

Jan 1, 1985

This chapter presents proportionate mortality ratios (PMRs) derived from death certificate data in the National Occupational Mortality Surveillance (NOMS) database for the years 1986 through 1993. At the time this report was prepared, 1993 was the latest year for which data were available. Industry is classified under the 1980 U.S. Bureau of the Census classification system [Bureau of the Census 1982]; cause of death, under the International Classification of Diseases, Ninth Revision (ICD-9) [World Health Organization 1977]. A PMR of 100 indicates a mortality risk for a particular industry group that is similar to that for all industry groups combined. A PMR over 100 suggests a higher risk; a PMR under 100 suggests a lower risk. PMRs are subject to many factors that affect their reliability and validity and may not be comparable across populations with very different causes of death. An elevated PMR for a specified cause of death among an occupational or industry group may indicate a relationship between a work exposure and the cause of death specified. However, there are many limitations of PMRs as a measure of risk; they are most useful for generating hypotheses about exposure-disease relationships, which can then be tested in other studies. Selected PMRs are presented separately for males and females for coal mining, metal mining, nonmetallic mineral mining and quarrying (which includes nonmetal, stone, and sand and gravel), and for oil and gas extraction. All PMRs have been adjusted for age and race. In general, PMRs are presented only if the lower 95% confidence limit exceeded 100. If a PMR in an ICD-9 subcategory was above 100, however, the PMR for the larger category into which the subcategory falls is always presented and may be less than 100. PMRs can be expected to be elevated for conditions that have a high prevalence in particular occupational groups. PMRs showed elevated values for conditions known to affect miners, such as coal workers' pneumoconiosis, pneumoconiosis due to silica, tuberculosis, chronic pulmonary heart disease, and injuries. Additional findings of interest were- • An elevated PMR for myocardial infarction among male coal miners (table 2-1); • Elevated PMRs for neurologic disease in general and anterior horn cell disease, in particular among male metal miners (table 2-3); • An elevated PMR for rheumatic heart disease in male metal miners (table 2-3); • Elevated PMRs for malignant neoplasms of the digestive organs and peritoneum and for malignant neoplasms of the colon and rectum in female nonmetal miners (table 2-6); and • Elevated PMRs for non-A, non-B hepatitis and arteriosclerotic heart disease among male oil and gas workers (table 2-7).

Jan 5, 2000

By Paul McIlroy

Costs of producing lead from various known resources in the United States are developed by the Bureau of Mines to define the future availability of domestic lead at various price levels. It is estimated that 60 million tons of primary lead (75 percent of the total resource) is available at $0.20 or less per pound; 72 million tons (90 percent of the total) is available at $0.50 or less per pound; and the 79 mil- lion ton total estimated resource can be obtained at a price or $1.82 or less per pound. The supply available at $0.20 per pound or less will meet demand for over 78 years at the 1970 annual consumption rate of 763,000 tons.

Jan 1, 1974

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.

By Gerald T. Homce

Data from the U.S. Bureau of Labor Statistics show that 89 water well drillers died on the job between 1992 and 2002, and 28 of these deaths were electrocutions (Figure 1). In fact, elec­trical accidents are the leading on-the-job killer of water well drillers. The use of electricity is such an integral part of our lives that we usually take it for granted, but if we don?t understand or choose to ignore the hazards associated with electricity, the results can be deadly. Why is electrical shock so dangerous? If the voltage (of a shock) is sufficient to drive electrical current through your body, just 10 milliamps of cur­rent (1000 milliamps = 1 amp) can cause muscles to contract and prevent you from releasing an energized wire or tool in your grip. As little as 30 milliamps of current can paralyze your breathing, and 75 milli­amps can cause your heart to stop pumping blood (ventricular fibrillation). As a comparison, a small bedroom night-light draws about 30 to 60 milliamps. Other factors influence how severely you?ll be shocked if you touch a live electrical circuit, such as the path electrical current takes through your body and how long it flows, as well as your body weight. How much voltage is needed to drive electrical cur­rent through your body? Not much! Generally, any power source at 50 volts AC or higher is considered dangerous.

Jan 1, 2008

By R. G. Gürtunca

Over the past century coal miner safety and health has seen tremendous improvements, the fatality and injury rates continue to decrease while productivity continues to increase. Many of the hazards that plagued miners in the past, such as coal bumps, methane and coal dust explosions, ground fall accidents and health issues have been significantly reduced. The contribution of NIOSH research includes products for prevention and survival of mine fires, methane control measures, design procedure for underground coal mines, methods for excavation surface controls, methods and procedures for blasting, laser usage in underground mines and prevention of electrocution from overhead power lines that have reduced accidents and injuries in underground coal mines. Health research has produced products such as the personal dust monitor, noise abating technologies and ergonomic solutions for equipment operators. Research priorities at NIOSH are set by considering surveillance statistics, stakeholder inputs and loss control principles. Future research in coal mining is directed towards respiratory diseases, noise induced hearing loss, repetitive musculoskeletal injuries, traumatic injuries, falls of ground and mine disasters. The recent spate of accidents in coal mines resulted in the Miner Act of 2006 which includes a specific role for NIOSH in future mine safety research and development. The mine safety achievements in the USA reflect the commitment of industry, labour, government and research organizations to improving the safety of the mine worker.

By P. S. Haury

"INTRODUCTION Preliminary examinations of the Mohawk zinc prospect were made by John 14. Price and the author in July, August, and September 1943. Considerable quantities of oxidized lead and zinc minerals were found in old shallow work¬ings along two faults - one an over thrust fault with Paleozoic limestone in the hanging wall overlying Cretaceous shale and arkose in the footwall of the fault, and the other a bedding fault in the Paleozoic limestone.The chances appeared good for finding important lead-zinc sulfide ore bodies at 200 to 300 feet beneath the surface, so exploration in three steps by the Bureau was recommended:Surveying, mapping, and character sampling of the outcrops with topographic and geologic mapping of the immediately surrounding area.Preliminary drilling of four test holes, aggregating about 1,500 feet, to locate the top of a possible sulfide ore zone and determine the thickness and intensity of the sulfide mineralization.Contingent upon favorable results of the second step, diamond drilling of about 6,300 feet of additional hole to explore the sulfide ore bodies.The outcrops were surveyed and sampled, a topographic map was made of the area, and the geology was mapped. A project was set up for preliminary drilling of step 2 in the fiscal year 1944-45. An access road to the drill sites was built in April 1945. Diamond drilling was started on April 28 and completed on September 25, 1945, under the supervision or the Bureau of Mines. The exploratory work is covered in this report."

Oct 1, 1946

By Liming Yuan, John C. Edwards, Gene F. Friel, Robert A. Franks

Diesel fuel fire experiments were conducted in NIOSH’s Pittsburgh Research Laboratory’s (PRL) Safety Research Coal Mine (SRCM) to determine the critical air velocity for preventing smoke rollback. Such information is necessary for the preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 kW to 300 kW depending upon the fuel tray area. Airflow in the 2 m high and 2.9 m wide coal mine entry was regulated during the course of each experiment; measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor; and recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light obscuration monitors, ionization smoke sensors, and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics (CFD) fire dynamics simulator.

By Susan B. Robertson, Gregory E. Hinshaw

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100%can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.

By Alvin Kaufman

Geothermal plants are competitive with conventional units. A geothermal plant can produce electric energy for 6.70 mills per kwhr, compared with 6.96 mills for coal, 6.74 mills for oil, and 7.04 mills for gas. These costs include fixed and variable charges. Potential for geothermal power exists in the Western United States, Alaska, and possibly Hawaii. Assuming that the current downward trend in cost per kilowatt of coal will cease and that the relative cost of gas and oil, already trending upward, may rise considerably more, geothermal energy will be utilized where available, in producing electric energy. It will be used in California first because it is directly competitive with gas-and oil-fired installations there. A long-term appraisal is difficult because little is known about the sources of geothermal power and the electric generating capacity which the steam fields will support. However, a market for geothermal steam-generated electricity exists within the Western States.

Jan 1, 1964

By Alvin Kaufman

Geothermal plants are competitive with conventional units. A geothermal plant can produce electric energy for 6.70 mills per kwhr, compared with 6.96 mills for coal, 6.74 mills for oil, and 7.04 mills for gas. These costs include fixed and variable charges. Potential for geothermal power exists in the Western United States, Alaska, and possibly Hawaii. Assuming that the current downward trend in cost per kilowatt of coal will cease and that the relative cost of gas and oil, already trending upward, may rise considerably more, geothermal energy will be utilized where available, in producing electric energy. It will be used in California first because it is directly competitive with gas-and oil-fired installations there. A long-term appraisal is difficult because little is known about the sources of geothermal power and the electric generating capacity which the steam fields will support. However, a market for geothermal steam-generated electricity exists within the Western States.

Jan 1, 1964

By Peter Swanson

One of the primary methods for analyzing roof stability in underground mines is the age-old method of “roof sounding” where a miner taps on the roof and listens for the hollow sound of loose blocks of rock. This paper looks at the feasibility of using noncontact laser-based vibration measurements to detect roof fall hazards with the ultimate vision of improving, expanding and automating procedures for mine roof inspection. Vibration measurements made on loose blocks of rock in underground mines are summarized and compared to estimates of fundamental resonance frequencies for rock slabs of the size responsible for highly hazardous “skin failures.” Both laser Doppler vibrometry and full-field interferometric methods are examined and are considered to be feasible methods for detecting anomalous vibrations in loose roof rocks. Results from simple laboratory experiments using laser vibrometry demonstrate some of the proposed application concepts. While considered a challenge to move these techniques from the laboratory to heavy industrial or outdoor environments, the potential for success in the current application is enhanced by the reduced requirements of qualitative analyses.

By John B. Umhau

[' is ann.tal surve:' gives sta.tistical data regC:ll~dirg rims.ry and feCOA-dUTY or ~cra:p tin used in thL United States by industries anc. includcc dc..ta l' is ann.tal surve:' gives sta.tistical data regC:ll~dirg rims.ry and feCOA-dUTY or ~cra:p tin used in thL United States by industries anc. includcc dc..ta ]

Jan 1, 1938