Search Documents

By William R. Barton

Sampling to determine development potential of beryllium deposits was conducted at 31 New England localities. A total of 54 additional areas where the geochemical environment appeared favorable were sampled to determine if economically interesting percentages of beryllia (BeO) might occur. Newry Hill-Plumbago Mountain, Maine, Iron Mountain, N.H., and Long Island, Maine, were investigated in some detail to determine the size and grade of deposits. The mineralized pegmatites at Newry Hill-Phunbago Mountain are extensive but very low grade; at Iron Mountain the ore bodies are very rich but of small volume; at Long Island beryl occurs with molybdenite, wolframite, and scheelite, but the tonnage of ore was not determined.

Jan 1, 1968

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

By J. A. Bartol

A survey was made of accident data and operating practices related to overloading and uneven load distribution on haulage trucks in noncoal open pit mines. Safety and economic aspects were analyzed. A bibliography of the literature was prepared. Review was made of available or projected systems for weighing or load indicating that might be applied to haulage trucks. A model specification was prepared for an overload detection system. Several promising systems for overload detection were identified. One was installed and tested briefly in a 170-ton rear dump truck in a copper surface mine.

Jan 1, 1982

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By Stephen Utter

Stresses induced by block-caving mining were estimated from in-place measurements of strain or deformation in rock and concrete around mine openings. The four types of gages used for measurements in the Climax Molybdenum mine during 1959-61 were Whittemore gage, Carlson strain meter,2 Valore strain cell, and Climax extensometer. Gage performance in the laboratory was evaluated by stressing instrumented rock and concrete specimens in a universal testing machine and by comparing measurements taken by the gages and a standard gage. Gage performance in the mine was evaluated by comparing measurements taken during an 18-month test. The Whittemore gage, Carlson strain meter, and the Climax extensometer proved suitable for the investigation; the Valore strain cell, effective in the laboratory tests, gave erratic measurements in the mine.

Jan 1, 1965

By R. P. Bush

The U.S. Bureau of Mines performed Cu exchange capacity (CuEe) tests on Ca and Na mont-morillonites and attapulgite clays. Mathematical models were developed from the data that the CuEe's are derived from for each clay as a function of pH, Cu concentration, and the concentrations of metal ions, which compete with Cu for exchange sites. An analysis was made of the impact of competing ions on Cu losses due to ion exchange. The results show that the CuEC's of clays, and hence Cu losses, are decreased by the presence of competing ions, and that AI and Mg have the largest impact of those cat-ions normally present in Cu leaching solutions.

Jan 1, 2010

By John J. Sammarco

The U.S. Bureau of Labor Statistics reports that the mining industry has the highest average annual fatality rate (31.9 per 100,000 workers) among all major American industry. To address this, a major research program to reduce hazard exposure of miners with computer-assisted mining equipment was initiated by the U.S. Bureau of Mines.1 One application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the haulage equipment so that it follows the machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors that can survive the hostile mine environment of dust, methane gas, and water, play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations were conducted to establish operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a sensing system. Various technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications but were found unacceptable. However, a near infrared (IR) sensor employing active targets met the requirements. The sensor has a nominal 75° conical field-of-view and a range from 0.1 to 18.0 m. For the single target mode, nominal range accuracy was 4.3% at a distance of 3.56 m. Correction algorithms were generated reducing the error to 0.6%. Airborne dust testing showed less than 0.8% accuracy (worst case) degradation at levels exceeding (by a factor of 7.5) concentrations permitted by Federal law. The sensor can track multiple active targets providing five degrees-of-freedom (DOF) measurements. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. A guidance system for the haulage system to follow the mining machine does not exist commer¬cially. Such a system can reduce fatalities and injuries by current haulage mining equipment, and is a viable alternative to current haulage control.

By S. Atallah

A survey was conducted relating to the current practices for the classification of hazardous locations in coal preparation plants. Several plants processing bituminous, anthracite and lignite coal in Pennsylvania, West Virginia, North Dakota, Colorado, Montana and Wyoming were visited. Coal preparation plant operations and designers as well as MESA inspectors were interviewed. The National Electrical Code was discussed with selected members of the NFPA committee and electrical equipment manufacturers. Data provided by MESA on fire and explosion accidents in coal preparation plants were examined. The requirements of the pertinent Federal Regulations, National Electrical Code, National Electrical Manufacturers Association and Underwriters' Laboratories were compared and evaluated. This report consists of two parts. Part I: "Analysis and Review" provides a summary of the findings. Part II: "Recommended Guidelines" consists of recommended uniform guidelines that may be used for interpreting the National Electrical Code as it applies to the classification of hazardous areas in coal preparation plants.

Jan 1, 1977

By George L. Gates

[When clays e.re mixe~ "Jith "~later to nake mud fluids f'ol' use in :irilling ','Iells "for oil and gar: h;:r vue :;'0 tary me thee. t 18 liquid mij~ tUl"es have certair.. phypicr..l characteri.",t.ics that vary ",dth t e Qlldlltit.y find]

Jan 1, 1941

By Ned Baker

Details are given of a fuel-induction system for a hydrogen, fueled engine. The induction system was designed to preclude backfire otherwise common in hydrogen fueled engines. System features and test data are presented and discussed in the context of the requirements peculiar to use in an underground mine environment. The fuel induction-system when tested in conjunction with a modified Caterpillar 3304 engine provided backfire free engine operation and satisfactory engine performance.

Jan 1, 1982

By V. B. Dale

San Manuel has been a modern prodigy from its inception to its present status as a block-caving operation producing 33,000 tons per day. The deposit was discovered, prospected, and developed with modern techniques, and nearly all planning was done from results of an extensive drilling program through an average overburden of 670 feet. The Federal Government had a prominent part in the discovery and primary development of San Manuel. The first 17 holes were drilled by the Bureau of Mines, and discovery of the large, low-grade, disseminated copper deposit is credited to the Bureau. A loan fund of 94 million was granted through the Reconstruction Finance Corporation to the San Manuel Copper Corp. for development of the deposit and erection of concentrating and smelting facilities. Then, while the mine was still being developed, the Defense Materials Procurement Agency contracted to buy a large amount of copper at a pegged price.

Jan 1, 1962

By Oliver Bowles

From the most remote periods of civilization, stone Las been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns) or single markers to great obelisks and pyramid or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1050 at a cost estimated at a: high as $50,000,000, and it is today an object of unusual attraction for travelers. Other magnificent memorials, both ancient and modern, are to be found in many lands. Memorials of varying design have characterized the passing centuries and have found an important place in the New World. In early days, monuments were chiefly imported into America, but gradually an extensive memorial stone-manufacturing industry developed on this side of the Atlantic. Sales value of domestic memorials, f.o.b. quarry or mill, attained a maximum of $17,488,755 in 1920, and retail sales, of course, reached a much higher figure. Modest markers and tombstones are to be found in almost every rural community in the United States, and there are many elaborate and costly monuments in and near urban centers.

Jan 1, 1938

By George A. Costello

A theoretical analysis is presented for the static and dynamic response of wire rope in deep-shaft mining operations. Expressions for the stresses in the individual wires of complex wire ropes are derived, and specific results for simple strands, 7x7 ropes, 6x 19 Seale ropes both with and without internal-wire-rope cores, and 6x25 filler-wire ropes both with and without internal-wire-rope cores, are presented for the case of ropes subjected to a combination of axial loading and bending over a sheave. Consideration is also given to the dynamic overloading associated with certain mining operations, such as dumping ore into a suspended skip and accelerating a fully loaded skip upward. Experiments to determine the axial stiffness of wire rope are described. Factors affecting the service life of wire rope, such as residual stresses, contact stresses, and fatigue behavior, are discussed. Specific research areas in need of further investigation are identified.

Jan 1, 1983

By V. E. Erwin, W. W. Adams, E. V. Walters

"Increased production of explosives in the United States in 1933 compared with 1932 is shown by statistics compiled by the Demographical Division, Health and Safety Branch, United States Bureau of Mines. The figures relate only to explosives used for industries purposes, such as mining, quarrying, and road building, and do not cover nonindustrial explosives, such as ammunition or fireworks. Industrial explosives include black blasting powder, permissible explosives, 5 and high explosives other than permissibles figures in the tables of this report were compiled from reports covering sales by the individual companies manufacture of explosives in the United States in 1933. Because of the close agreement among the several series of figures, the quantity of explosives sold is considered as reflecting production and consumption, and the three terms ""sales"", ""production"", and ""consumption"" are used interchangeably in the discussion unless otherwise stated.Of the principal industries that use high construction operations accounted for the largest percentage of increase in consumption during 1933; metal mining and quarrying also used more of this class of explosives than in the previous year. Coal mining is the chief consumer of permissible explosives; the figures for 1933 showed that bituminous-coal mining used a larger quantity than in 1932, and that anthracite mines also showed a small increase. Although a net increase of less than 1 percent in consumption was reported for black blasting powder, large increases in use of this class of explosives were reported for metal mining, miscellaneous types of work, and bituminous-coal mining. (See table 1.)"

Nov 1, 1934

By Richard H. Bares

One criterion central to most definitions of reclamation is the restoration of mined lands to their original productive potential. This is often difficult to achieve on mined lands in the Northern Great Plains because of the rigorous climate (Bares 19;2) and various soil related problems including sodicity, salinity, soil permeability, low organic matter and plant nutrient deficiencies (Malakondaiah and Safaya 1982). Field study sites were established on recontotured mined areas during the early 1970's (prior to the topsoil mandate) in which several amendments were tested for their ability to improve spoil/topsoil conditions and, hence, increase plant production. Physical and chemical properties of these control (untreated) and amended spoils and topsoils have been summarized (Safaya et al. 1982). A number of grass and legume species combinations were studied. The general effects of one time (prior to seeding), single rate (approximately 100 mT ha-1) application of leonardite and/or slack coal to spoils and topsoils was the reduction of grass dry matter yields (NB 1 test site: dry matter yield (DMY) without slack was 110 g m 2 yr I ; DMY with slack was 80 g m -2 yr 1 I and the promotion of legume establishment and yield (SB test site: DMY without leonardite was 13 g m 2 yr -1; DMY with leonardite was 93 g m 2 yr 1). On South Beulah topsoil, treated with leonardite, production of weedy species was remarkably lower than that without leonardite (SB test site: DMY without leonardite was 252 g m - yr -1; DMY with leonardite was 177 g m 2 yr 1). The general effect of commercial fertilizer applied one time prior to seeding (rates ranging from 9-13-0 to 44-1 12-28 kg ha-1 of N-P-K) was to increase plant production during the first two to three years after which the effect disappeared. This effect was much more pronounced on spoils (NB I test site: DMY on spoils without fertilizer was 53 g m -2 yr -1; DMY on spoils with fertiliser was 132 gm -2 yr -1). Weedy species accounted for most of the biomas, production during the first growing season. Three of the test sites were designed to study plant production on topsoils and spoils. Establishment and production of grass species were comparatively better on topsoils (30 cm in depth) than on spoils while legumes were most successful on the soils (Center test site, 1979; DMY of grasses on topsoil was 170 g m 2 yr -1 DMY of grasses on spoils was 52 g m -2 yr -1; DMY of legumes on topsoil was 20 g m -2 yr -1; DMY of legumes on spoil was 191 g m 2 yr -1). Total plant production on topsoiled (302 m thickness) plots at the South Beulah site (DMY in 1979 of 269 g m 2 yr 1) was comparable to that of native western wheatgrass prairie (DMY of 262 g m -2 yr -1). An experiment was conducted to find out if time of planting would have any effect on establishment of grasses on spoils. It was fund that late fall seeding was superior to spring planting for establishment of wheatgrasses at NB 3 test site (Control Plot, 1975: DMY on spring-seeded was 1 g m -2 yr - 1; DMY on fall-seeded was 55 g m -2 yr -1). In general, wheatgrasses (slender, streambank, thickspike and western) yielded the most aboveground biomass of all the grass species tested; yellow sweetclover was the most successful legume. Yellow sweetclover established and was productive on both spoils and topsoils but only where competition with grasses was apparently minimal. Durar hard fescue established and thrived on topsoil but dry matter production was low compared to that of wheatgrasses. Emerald crown-vetch demonstrated a potential for growth on spoils where water conditions were adequate, whereas side-oats grama, prairie sand-reed, alkali sacaton, and bird's -foot trefoil demonstrated only sporadic success. Little bluestem did not become established at any of the test sites. Peak production of the planted species, especially grasses, was generally reached by the second week of July. Legume and weed production continued to increase into late August.

Jan 1, 1982

By Ronald M. Lewis

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 00 to 90° for FeKa and from 25° to 180° for FeKa1. The wavelengths used for Fe in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): FeKa1 1.93597 A.; Feka2 1.93991 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn. X-ray diffraction crystallography using tubes with iron targets revealed a need for a handy reference for the quadratic functions of iron radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

By JeffreyS. Vipperman, Daniel R. Babich, EricR. Bauer

In response to the continuing problem of noise induced hearing loss NIHL among mine workers, the National Institute for Occupational Safety and Health NIOSH has conducted numerous noise surveys in coal preparation plants. The research, consisting of worker dose monitoring, task observations, and equipment noise profiling, was completed in eight separate preparation plants. Worker dose monitoring was conducted for three shifts in most cases. Workers experiencing higher than allowable doses were task-observed for one full shift to correlate dose to noise source(s). Finally, noise levels on all floors, and in lunchrooms and control rooms, were characterized. Results indicate that only workers who routinely spend a significant portion of their shift in the plants (away from the control rooms) are susceptible to overexposure from noise. Certain pieces of equipment (screens, centrifuges, sieve bends) are the loudest primary noise sources responsible for the worker noise exposures.

By Ernest J. Conway

This report presents engineering drawings for six material handling devices for underground coal mines. The devices were designed under a U.S. Bureau of Mines program to reduce injuries from material handling during mine and equipment maintenance. The six devices are (1) scoop-mounted 1411: boom, (2) swing-arm boom, (3) heavy-component lift-transport, (4) mine mud cart, (5) container-workstation vehicle, and (6) timber car. Each device is described briefly, and recommendations are made concerning the design of new devices.

Jan 1, 1989

By Marc Ruest, Lewis Martin

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC’s Granger Mine, Meikle Mine, and Getchell Mine. A “split-pipe” laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

By Robert W. Waytulonis

This publication contains 1,000 citations of technical and semi-technical literature treating diesel-powered equipment usage underground both generally and specifically. These citations were gathered by U.S. Bureau of Mines personnel over the period of 1978-1983. The citations concern diesel engines as powerplants for underground mining use; their design, emission characteristics and control, maintenance, usage; and health and safety aspects. All citations have been abstracted and arranged 1n a subject classification system with extensive cross-referencing.

Jan 1, 1983