Search Documents

By Ellis S. Hertzog

The material published in this report is part of a special study of some of the chemical and physical properties of Alabama coals. The complete study included friability and grindability determinations, high and low temperature assay distillation tests, and ash fusion-temperature determinations. Proximate and ultimate analyses and. calorific values of the coal samples also were obtained. This paper is concerned only with grindabilities, although proximate analyses have been included to give a better picture of the problem as a whole. The growing interest in grindabilities of coals is a result of the increase in use of pulverized fuel in rescent years. The tenative ball-mill grindability method D408-35T4/ was used in making all the determinations. The method of sampling and the technic of the testing procedure is described in Considerable detail in this report because the procedure was established quite recently. The ball-mill grindability index is a measure of the ease with which coal may be ground, which may be an important factor in estimating pulverizing costs. Up to the present time few data on the grindability of Alabama coals have been published. The data in this paper show that the Warrior and Cahaba fields exhibit a wide range of grindability in their coals. The mines tested are well distributed throughout the productive areas of these fields, and it is possible to make rough estimates of the grindabilities of coals not listed in this report from the data given for mines situated in the same vicinity.

Jan 1, 1938

By M. G. Zabetakis, T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed ms investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years a ago were only laboratory curiosities.

Jan 1, 1941

Ecuador a gross domestic product (GDP) grew 8% despite a slowdown in production and sales of petroleum, the dominant economic sector. Crude petroleum exports, which amounted to about 35% of total exports in 1977, were valued et $484 million,2 a decrease of 14% from 1976 values. Petroleum export sales were depressed because foreign buyers were somewhat uncertain that State-owned Corporación Estatal Petrólera Ecuatoriana (CEPE) held legal title to the oil until final settlement with Ecuadorian Gulf Oil Corp. In addition to the legal complication, Ecuador maintained a relatively high export price for oil until late in the year. There was also a shrinkage of traditional U.S, markets owing to the Alaskan pipeline becoming operational and an increased availability of Mexican supplies. The export market was also affected by increased domestic production in Peru and Chile, which lessened their import needs, and the pressure of greater competition from the Middle East in supplying crude oil to Caribbean refineries. About 20.4 million barrels or 40% of Ecuador's total crude exports went to the United States. Only 27 wells were drilled in Ecuador during L977; of these, 16 produced oil, 3 were dry holes, and 8 were suspended. About 31 wells were planned for 1978. Three new oilfields were discovered during 1977; two by CEPE in northeastern Ecuador and one by the Argentine State oil company Yacimientos Petraliferos Fiscales (YPF), operating in Ecuador under a service contract. CEPE's two discoveries tested at 5,000 and 1.450 barrels per day, respectively. The YPF discovery tested at about 1,000 barrels per day. Ecuador altered its position regarding

Jan 1, 1981

By John J. Mulligan

The Bureau of Mines investigated coal deposits at Mount Gran (latitude 76°59' S, longitude 161°07' E), Victoria Land, Antarctica, during the austral summer of 1959-60 as part of the continuing U.S. Antarctic Research Program, which is under the auspices of the National Science Foundation. The coals and associated rocks were measured, sampled, and analyzed. Five coalbeds, ranging in thickness from over 10 feet to scattered fragments of coaly material in sandstone, occur in a sandstone-coal series overlying a series of crossbedded red-buff sandstones. Both series are part of the Beacon group of sediments, and both show some evidence of pressure metamorphism. The sandstones are poorly cemented and are composed dominantly of rounded and often frosted quartz grains. The sediments have been broken and uplifted by a series of massive diabase sills. The broken nature of the sediments precluded an estimate of the amount of coal present. The Mount Gran coals are highly attrital banded anthracites and semianthracites that have most commonly a moderately dull luster but do include bright bands. Coal in contact with or near diabase intrusives is partly graphitic but shows no evidence of coking. Apparently the coal was beyond coking rank before emplacement of the adjacent intrusives. Fragments of the plant Glossopteris indica found with the coal suggest Permian age but do not prove it. The coals appear to be derived from plant remains that collected in shallow basins; individual coalbeds would tend to be lenticular bodies that formed in different places as the dominantly sandy sediments were deposited. The wide distribution of coal indicates that coal-forming conditions prevailed over much of the continent; the great thickness of Beacon sediments indicates that similar conditions may have persisted through a long period of geologic time. Generally similar coal deposits may occupy widely separated stratigraphic positions.

Jan 1, 1963

By E. C. Lane

During the past 15 years the Bureau of Mines has made and published several hundred analyses of typical petroleums and has developed a system of interpreting the analyses and of classifying crude oils. In describing crude petroleum frequent reference is made to the "base" of the oil, a usage the petroleum industry has found convenient. As part of its general study of the characteristics of crude oils, therefore, the Bureau of Mines has developed a system of classifying them according to "base." This system as first published in 19274 was limited to four classes and in its original form is no longer considered adequate. Since the system was first published the Bureau has analyzed a large number of crude oil-, including representative samples from nearly every important producing field in the world, and has found that the system of classification could be revised and amplified to advantage. The revised system is presented herein. Bulletin 2916 states that many oil producers and refiners use the word "base" much as it is used in pharmaceutical work. For example, the "base" or "basis" of an ointment or salve is the fatty material (lard, petroleum, or lanolin) used as a vehicle or carrier for the active medicinal principles. Apparently many of the pioneers in the petroleum industry considered crude oil similar in nature to these medicinal products in that it consists of a semisolid, nonvolatile base and 1 volatile portion can be distilled off to make gasoline, kerosene, and other products. Many crude oils when chilled slowly deposit a waxy material (paraffin); this fact may have been one reason for the use of the term "paraffin base" in referring to such oils. Almost all of the petroleum first discovered in the United States was of this nature; not until the oil industry was extended to California and along the Gulf coast was petroleum found that contained no wax but apparently did contain asphaltic material Accordingly, these oils were known as "asphalt-base" oils. The use of this term, however, seems unfortunate, as better-grade oils of this type contain little if any asphalt; the descriptive term "naphthene base" now seems to be a more desirable term than "asphalt base." The term "intermediate base" is also used commonly in referring to oils intermediate in oharacteristios between those of paraffin and naphthene base.

Jan 1, 1935

By D. J. Dollhopf

This research was part of an effort to investigate means of reestablishing non¬polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. Chemically undesirable overburden material was selectively backfilled with the intent that it would be below the future root zone, be above the reestablished aquifer, and would not be leached as a result of deep percolation. After 2 years the buried material remains above the spoil aquifer and below the maximum rooting depth. Unsaturated water flow from the land surface to the buried material occurred during wet climatological periods. No significant leaching of buried material was observed, however. Overburden sample contamination from drill stem joint grease with Pb, Zn, and Cu additives caused substantial error regarding DTPA extractable trace metals. A grease with teflon and talc additives was recommended for use in future sampling programs. DTPA extractable trace elements in overburden material had no statistical relationship to post-mine ground-water quality. Overburden columns leached with water produced leachates comparable to overburden and spoil ground-water trace metal quality. A depositional model described the Rosebud Coal overburden as a fluvial system with distinct units of sand, silt, and clay, with distinct chemical properties. Physical and chemical characteristics of the model were comparable to the in situ geochemical system, a relationship which may aid in locating overburden materials unsuitable for reclamation.

Jan 1, 1979

By D. L. Yopps

In research conducted by the U.S. Bureau of Mines, platinum-group metal (PGM) flotation concentrate from the Stillwater Complex, MT, was subjected to biooxidation using Thiobacillus ferrooxidans in an effort to break down the sulfide minerals and liberate the associated PGM's for subsequent chemical leaching. Bacterial preleaching oxidized up to 94 pct of the sulfide present, destroyed the PGM-bearing pentlandite [(Ni,Fe)9S8] mineralization, and dissolved most of the nickel in the concentrate. Cyanidation at 80° C proved to be the most attractive chemical leachant, removing 34 pct of the platinum, 76 pct of the palladium, 94 pct of the rhodium, and 97 pct of the gold from the biooxidized concentrate. Research also indicated that increased sulfide oxidation during the preleach phase led to improved PGM recovery in the subsequent chemical leaching phase.

Jan 1, 2010

By John J. Sammarco

The U.S. Bureau of Mines seeks to increase safety and efficiency in U.S. coal mines. One approach is to develop technology for automation of a continuous mining machine. Realization of an autonomous mining machine requires development of subsystems for machine intelligence, navigation-positioning, and computer control. This report focuses on investigation of one subsystem, an onboard heading system, which would be responsible for determining and controlling machine heading. The onboard heading system investigated is a multisensor system to determine machine heading, pitch, and roll. A directional gyroscope provides heading (yaw), fluxgate sensors provide a compass heading, and gravity-referenced clinometers give machine pitch and roll. The system utilizes a dedicated microcontroller networked to an external system of computers. Tram commands, supplied to the network from external computers, are executed by the onboard system. Sensor feedback is employed for closed-loop control of machine heading by controlling pivots and turns. The report discusses operating limitations and error sources of system sensors and presents test results of closed-loop control of machine heading. Results of tests with a mining machine are used to exhibit various sensor shortcomings and to evaluate control of pivots and turns.

Jan 1, 1990

By Kray Luxbacher, Erik Westman, Peter Swanson

Three-dimensional time-lapse velocity tomograms were generated to image stress redistribution around a longwall panel to produce a better understanding of the mechanisms that lead to ground failure. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Most similar studies have utilized active sources including longwall shearers, controlled explosions, and hammer blows. These active sources generally require a person to initiate and measure the location and time of the source, and are not conducive to continuous monitoring. This method utilizes mining induced microseismic events as passive sources and lends itself well to continuous monitoring. Two event location methods were compared in order to move toward quantification of tomographic results in terms of ground conditions. Additionally, LAMODEL was utilized to determine the expected stress distribution around the longwall panel and compare these images to the velocity tomograms. Eighteen tomograms were generated, one per day, and high velocity regions in the set of tomograms generated from the initial location algorithm correlated with abutment stress redistribution predicted by numerical modeling. This research is significant as it has the potential to improve safety in underground mines and is the only example of long term passive velocity tomography implementation for the purpose of inferring stress redistribution around an area of active mining. Though still immature, this technology has the potential to allow mine personnel to image areas of active mining on a regular basis and detect areas with anomalous velocity distributions indicating potential safety hazards.

By D. Harrington

Near the close of the nineteenth century electricity was introduced underground, and the mining industry automatically was confronted with another potential source of fatalities and injuries to mine workers. Electricity has become an increasingly vital factor in the production of goal, particularly in recent years, because of the greatly extended mechanization that has taken place underground. The enlarged use of electrical equipment for cutting, loading, and hauling coal unquestionably increased the potentiality of shock and explosion hazards underground. Electricity may be used in coal mines with minimum danger if electric equipment and power-carrying wires are chosen properly and installed and kept protected by proper safeguards; on the other hand, if vigilance is relaxed in the slightest degree accidents may result. Electrical accidents are caused chiefly by direct contact with electrical equipment or power-carrying wires, by ignition of explosive gas or dust, and by fires of electrical origin. Electricity now ranks fourth as a cause of coal-mine fatalities, not including deaths from explosions or fires of electrical origin.

Jan 1, 1936

By Graham W. Marks

Recently it was shown the total energy method of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing, this work, the present report deals with analyses for beryllium, zinc, cadmium; and indium. There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved. As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is, associated with zinc and cadmium in zinc ores.

Jan 1, 1948

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel- economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the 3 reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By R. H. Schutz

TO ASSIST users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines bas established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules include 130 for self-contained breathing apparatus, 141F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and .mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pitts- burgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the deice meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines he used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators.

Jan 1, 1966

By R. H. Schutz

TO ASSIST users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines bas established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules3 include 13D for self-contained breathing apparatus, 141F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pittsburgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer4 of the respirator and at his expense. If the device meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines he used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators.

Jan 1, 1966

By J. W. Miller

Wyoming County had for many years supplied large quantities of coking coals to coke plants throughout the eastern United States and Canada. Up to the present most of the coal has been produced from relatively few beds, but in the future the coal will be produced from beds not previously mined in quantity. This trend is shown in the entire Winding Gulf field, of which Wyoming County is a part. This publication is one of a series of Bureau of mines reports appraising the Nation's coking coal, which y be used to determine the practicability of upgrading marginal deposits to metallurgical standards. This investigation of the preparation characteristics of Wyoming County coals is the third of the series undertaken in West Virginia.

Jan 1, 1955

By W. L. Hunter

The research on this report was conducted to obtain information on the feasibility of producing ferro chromium of varying silicon and carbon contents from domestic chromite. Concentrates from the Mouat deposit were chosen because they typify the chromite found in the Stillwater complex, the largest domestic reserve, and are similar in composition to other extensive North American and foreign deposits. Batch-smelting tests designed to produce high-, medium-, and low-carbon ferrochromium were made in single phase and three-phase, electric-arc, steelmaking furnaces. Agglomeration studies were made in a rotary kiln. Continuous smelting tests were made to yield data on the production of high-carbon ferro chromium and low-carbon ferrochromium-silicon. The carbon content of high-carbon ferrochromium was lowered to the medium-carbon range by oxygen injection. Mouat stockpile concentrates were nodulized in a gas-fired rotary kiln using quartz, limestone, and fluorspar additions in the proportion necessary to flux the slag. The nodules were smelted in a continuous test using coal, coal char, and mixtures of the two consecutively as reductants.

Jan 1, 1961

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pressure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water-treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963

By Elbridge W. Gresseth

Rock deformational structures in a deep mine were analyzed by petrofabric techniques to learn (1) the relative magnitude and direction of the principal stresses involved in tectonic deformations prior to mining, (2) the preferred orientation of rock planar discontinuities which define rock anistropy prior to mining, and (3) the relationship of mining-induced rock failure to inherent rock stresses and inherent rock anisotropy. Rock fabric elements used for petrofabric analysis consisted of bedding planes, faults, joints, fractures, foliation, sericite plane (001), quartz axis [0001], quartz deformation lamellae, and microfractures. Structures and structural symmetries from different areas within the mine and from different scales of observation were compared to learn the nature of rock anisotropy and the orientation of the principal stresses defined by rock deformations. Analysis of such fabric as regional and macroscopic faults, b-c joints, quartz [0001], sericite (001), and microfractures, indicate that during the epochs of tectonic deformation, the maximum and minimum principal stresses were horizontally oriented and acted along northwest and northeast axes, respectively. This condition of regional stress appears to have continued during folding and the associated period of faulting. The most recent tectonic deformation represents a rotation of the minimum principal stresses into a vertical position, as shown by the development of a tensile joint system, quartz deformation lamellae, and microfractures. Good interscale correlation and statistical homogeneity of tectonic fabric indicate a stress field homogeneity in this area during tectonic deformation. Rock physical anisotropy is genetically associated with tectonic fabric and consists of preferentially oriented planar discontinuities intersecting along a nearly vertical axis. The mining-induced deformations were correlated with the inherent rock anisotropy which either directly controls or greatly affects their development. This phase of rock deformation shows a greater degree of stress field heterogeneity than was the case with tectonic deformations This is explained as a result of nonconfinement afforded by underground openings and the increase in ground stresses due to mining activity"

Jan 1, 1968

By Dana T. Updyke

The objective of this project was to develop technical data and evaluate performance and utility of leaky feeder communications systems currently used in North American underground mines. The desired information was obtained principally through on-site surveys. Altogether, six of the seven mining companies known to be using leafy feeder communications were visited. This report covers the findings of these surveys. In addition, the report provides a brief background summary of mine communications, a technical discussion of leaky feeder systems, and conclusions and recommendations based on the results of the survey.

Jan 1, 1980