Search Documents

By T. M. Barczak

Longwall tailgates in coal mines are often subject to severe mining induced loading and deformation. Innovative tailgate supports have been developed over the years to provide safe and economical access and a ventilation pathway at the tailgate. The support capacity and yield capabilities of the supports need to be matched to the loading imposed by the surrounding rock mass. The ground response curve can be used to represent the rock mass response to mining and its effect on support systems. The FLAC finite difference code was used to supplement field results by simulating a longwall tailgate and the associated ground response. The ground response curve is developed by modeling tailgate excavations with different internal support pressures and recording the resulting convergence. Ground response curves are developed for two typical longwalls operating in the Pittsburgh seam with weak and strong immediate roof. An additional model is presented in which the effect of weak overburden strata is simulated. The ground response is shown to be significantly affected by the strength of the immediate roof as well as the main roof. The importance of yield capacity of standing support is demonstrated. Gob height and compaction are found to affect the amount of convergence in the tailgate. The potential exists to develop site specific tailgate design curves by combining model results with field observations.

By James W. Myers

"Packaged fuel" is the trade name applied by the industry to a product consisting of coal screenings and a binder compressed into 3 -or 4-inch cubes and wrapped (six or eight in a package) in sturdy paper and sealed with gummed tape. Parry describes the product in greater detail and distinguishes clearly between packaged fuel and briquettes. The industry developed from the desire of retail coal dealers to improve utilization of the relatively large quantities of slack sizes that result from the degradation, during shipping and handling in the yard, of friable coal, particularly Pocahontas coal. During the war an attempt was made to apply this technique to anthracite fines, and a recent publication of the U. S. Bureau of Mines reported the results of physical and combustion tests on packaged fuels containing anthracite fines. References made in this report to the previous investigation on packaged fuels containing anthracite represent data or conclusions presented in Report of Investigations 3882. This investigation was conducted as a continuation of the previously reported studies and consisted of physical and combustion tests of packaged fuels made from high-volatile bituminous coal, as well as the low-volatile bituminous coal ordinarily used in the industry, to determine their relative suitability for domestic firing. Particular attention was given to the smoke-producing properties of the packaged fuels because of the increasing importance of the prevention or reduction of smoke from hand-fired domestic heating plants resulting from the widespread enactment of smoke-prevention ordinances.

Jan 1, 1951

By C. C. Popoff

The Dunkleberg district is in the Flint Creek Range of the northern Rocky Mountains, about 45 miles northwest of Butte, Mont. Silver - lead and zinc mineralization occurs over an area 4 miles long from north to south and 1 to 2 miles wide from west to east. Ore in appreciable quantity has been produced, mostly from the Forest Rose group of mines in the southern part of the district. The Forest Rose mine was the largest producer of lead and the Wasa mine, a mile farther south, the main producer of zinc. The total output of ore from these properties during World War II was 113,000 tons, or 98.2 percent of the total recorded production of the district. The Wasa mine was examined by a Bureau of Mines engineer2/ in 1944. Subsequent investigations during 1946, 1947, and 1948 included trenching and drilling Fn the Wasa area and examination of the Forest Rose and other mines.

Jan 1, 1953

By J. T. McCartney

OPTICAL PROPERTIES of U.S. coals of differing rank have been investigated by the Bureau of Mines, for about 20 years. These investigations have been remade to further the development of an objective basis for petrographic analysis of coal and to add to knowledge of the structure and composition of coal and coal components by determining their optical constants in various regions of the electromagnetic spectrum. Various experimental techniques have been used in these studies, including determination of reflectance from bulk specimens and transmittance of thin and ultrathin sections, interferometry, electron microscopy, and election diffraction. Similar studies leave also been made of graphite, the end product of coal metamorphism. The bureau of Mines conducted the first U.S. investigation of reflectance properties of coal components, laying the foundation for petrographic analysis based on arbitrary reflectance classes and for automated reflectance analysis of coals. Optical constants of coals of differing rank and of graphite have been determined in the ultraviolet-visible-near infrared spectrum. Maxima in the optical constants of graphite were observed in the ultraviolet region and were interpreted to be related to transitions of electrons between the valence and conduction bands. Similar maxima for coals, especially high-rank coals, appeared to be characteristic of the presence of graphitelike layers. A special application of optical theory to absorbing, anisotropic materials like graphite and high-rank coals has been developed. Electron microscopic and electron diffraction studies of coals have revealed various ultrafine structures in coal components and have shown the evolution of an oriented, crystalline graphite structure in high-rank coals.

Jan 1, 1967

By K. B. Nowels

"INTRODUCTION For the last several years the oil industry has been turning more and more toward conservation arid the study of related production problems. It is generally conceded that ultimate recovery is increased by holding the natural gas in thy sand which is net needed in lifting the oil. The retained gas lowers the viscosity and surface tension of the oil and helps flow the oil from the sand. Lewis states that ""while the operator can not control the original conditions of energy and resistance in the sand, he can partly control the efficiency of expulsion. As it is the energy contained in the compressed and absorbed gas rather than the oil that is exhausted, it is but logical to judge the efficiency of a producing method largely by the relative quantities of gas produced with each barrel of oil. If by a change in method the producer lessons the proportion of gas with each barrel of oil, he should increase the total recovery- of oil correspondingly, even if the rate of production is temporarily reduced somewhat.""The effect of ""pinching in"" or controlling the flow of oil wells in an effort to lessen the proportion of has never been definitely known. The general belief has been that ""pinching"" a flowing well causes the oil and gas volumes to be reduced proportionately, maintaining the same gas-oil ratio as before the reduction in flow was made. Studies of gas-oil ratios in many fields have shown that much gas has been wasted, insofar as its effectiveness in oil production is concerned. Swigart and Bopp carried."

Oct 1, 1927

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 39,420 acres of the 60,960-acre Skedaddle Wilderness Study Area in order to evaluate its identified mineral resources. There are no known mines or mining operations in the study area. None of the prospects or claims in or within a 1 mile peripheral zone around the study area have recorded production. At least 276 recorded lode, 6 unrecorded lode, and 29 placer claims have been located in and within about 1 mile of the study area. Approximately 191 of the claims are in the study area. Four of these were current in 1985; all four are wholly or partly inside the study area. None of the study area was being explored by private industry in 1985. Metallic and nonmetallic commodities present in the study area consist of gold, mercury, perlite, basalt, pozzolan, stone, and sand and gravel. Perlite is represented by a single deposit which contains 184,000 tons of subeconomic resources in and adjacent to the study area. No other sites contained identified resources. There are no other identified nonmetallic resources in the study area. Occurrences in and near the study area contain small amounts of gold and mercury in vein-type deposits and show characteristics similar to bulk-tonnage, low-grade gold deposits. No base-metal resources were identified. The gold and mercury mineralization and perlite deposit are spatially related to a volcanic center located in the Skedaddle Mountains. Prospects in the Skedaddle Mountains may contain both precious metals and perlite resources, but additional work is required to adequately delineate these areas.

Jan 1, 1987

By James C. Duchon

The use of extended workdays (regular shift lengths of 10 or 12 h (hour), while still maintaining a 4O-h workweek) in mining operations is attracting growing interest in the United States. There is very little doubt that extended workdays is a very popular alternative among the work force because of the significant increase in days off, including weekends, especially when compared with traditional rotation schedules of working seven straight shifts or having only one weekend off every 4 to 6 weeks. However, there are some serious concerns by management, workers, unions, and various governmental policymakers that working 10-or 12-h days may create an added risk of accidents and health problems. The U.S. Bureau of Mines reviewed the literature studies related to the safety and performance issues of extended workdays. This report presents a summary of those findings. The studies examined in this review are divided into three sections: (1) laboratory, (2) field, and (3) accident and injury analysis. In general, results are inconclusive. Studies have shown both positive and negative effects. It is concluded, therefore, that in industries such as mining where accidents are a serious concern, special measures and evaluation in the use of extended workdays be considered.

Jan 1, 1994

By D. P. Lindroth

The Bureau of Mines is engaged in research on ground probing radars for detection of geologic hazards in advance of mining. Penetration distances and interpretation models depend on the dielectric properties and wave propagation characteristics for coal measure stratified media. Relative dielectric constants and dissipation factors were measured under ambient conditions for Pittsburgh Seam coal measure rock over the frequency range of 20 to 100 MHz by the susceptance-variation method. The rock types measured were representative sedimentary rock located above the Pittsburgh Coal Seam. Extreme values for the computed attenu-ation distance ranged from 1.7 m at 100 MHz for siltstone to 230 m at 20 MHz for a particular limestone.

Jan 1, 1984

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By Richard H. Spencer, Thomas E. Doerfler, Robert L. Lagace, James M. Dobbie, William S. Hawes

This report assesses the expected detectability, on the surface above mines, of electromagnetic signals produced in the frequency band of 630 to 3030 Hz by a rescue transmitter activated by miners trapped underground. This assessment is based on a statistical analysis of experimental signal and noise data taken at a representative sample of coal mine sites well distributed over the United States underground coal fields. Regression analyses are performed to characterize the signal transmission behavior of overburdens as a function of depth and frequency. The predicted signal behavior is then combined with experimentally based distributions of the background noise, and aural detection characteristics of signals in noise, to generate curves of the expected probability of detection for trapped miner signals versus overburden depth and operating frequency. The implications of these results, and associated recommendations, are presented regarding the detectability of trapped miners, sensitivity analyses and confirmatory tests, and operational utilization considerations for the trapped miners and the search and rescue team on the surface.

Jan 7, 1980

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By D. Eugene Rannels, Sarah E. Dunsmore, Cara Martinez-Williams, Yu-Chen Lee

"Dunsmore, Sarah E., Yu-Chen Lee, Cara Martinez Williams, and D. Eugene Rannels. Synthesis of fibronectin and laminin by type II pulmonary epithelial cells. Am. J. Physiol. 270 (Lung Cell. Mol. Physiol. 14): L215-L223, 1996.Previous investigations demonstrated that type II pulmonary epithelial cells regulate extracellular matrix deposition as a function of time in primary culture. In those studies, the matrix fraction was analyzed as a whole. The present work focused on two components of the type II cell matrix, fibronectin and laminin. These glycoproteins have differing effects on differentiation of type II cells in primary culture. Fibronectin synthesis was quantitated between day 1 and day 6 in the cells, matrix, and medium; laminin synthesis was quantitated only in the cells. Although total fibronectin synthesis was regulated as a function of time in culture, reaching its greatest value on day 2, the average proportion of newly synthesized fibronectin in the cells (35%), medium (50%), and matrix (15%) remained constant over a 6-day interval. Between day 2 and day 6, the relative abundance of fibronectin messenger RNA increased 6.5-fold. Rates of cellular laminin synthesis did not vary with time in culture. These results support a role for differential regulation of fibronectin and laminin synthesis to determine the composition of the type II cell extracellular matrix. INTERACTIONS BETWEEN THE pulmonary epithelium and alveolar basement membrane may play a role in the physiology and pathophysiology of the lung. Pulmonary epithelial cells and the alveolar basement membrane form one component of the blood-gas diffusion barrier. Integrity of this barrier is crucial to normal lung function. Specific domains of alveolar basement membrane components have been proposed to determine localization of type I and type II pulmonary epithelial cells during lung growth and development, as well as during repair of the alveolar surface after injury (13). In the injured lung, the extent of damage to the epithelium and the underlying basement membrane is thought to be a key factor to determine subsequent repair or fibrotic scarring (3)."

Jan 1, 1998

By H. E. Powell

Basic data were recorded on the decompositions that take place during thermal decomposition of siderite (FeC03). Both the naturally occurring and a synthetically prepared mineral were studied by differential thermal, thermo-gravimetric, X-ray-diffraction, and chemical (including gas) analyses. Thermal decomposition was studied in the media of dry air, moist air, dry carbon dioxide, dry helium, and dry carbon monoxide and at atmospheric and at reduced pressures. Results showed the thermal decomposition of FeC03 to be an extremely complex process, dependent on environmental factors and side reactions that cannot now be completely controlled. Therefore, full understanding of the reaction involved must depend on additional research with advanced evaluation techniques.

Jan 1, 1965

This work examined the feasibility of in-mine coal preparation in two phases. Phase I included a survey of previous investigations and a preliminary analysis of the economic and technical feasibility on a selection of representative sites and degrees of cleaning. The contract was terminated at the end of Phase I. The preliminary analysis determined that in-mine preparation systems can be applied using currently available technology. The most likely mines for application will have shaft or slope access and be deeper than 500 feet. The refuse disposal systems technically feasible are (1) pneumatic placement of coarse refuse in room and pillar panels or longwall faces, (2) mechanical placement of coarse and fine fractions in room and pillar panels, and (3) hydraulic placement of fine fractions in room and pillar panels. The economic feasibility is much more dependent on the refuse disposal-system than on the preparation system. It is estimated that the capital cost of an in-mine preparation and disposal system would be $6.00 per clean ton and the operating cost would be $1.24 per clean ton for a 1 million clean ton per year mine.

Jan 1, 1982

By Arcy R., D&apos George

A process for removing sulfate from Great Salt Lake brines and other natural brines, including sea water, has been developed. Sulfate is quantitatively removed by precipitation as barium sulfate in a cyclic process employing ion-exchange techniques. Barium is continously recovered and recycled, and sodium carbonate and sulfur or sulfuric acid are produced as byproducts in quantities sufficient to more than defray the cost of desulfation.

Jan 1, 1967

By R. V. Ramani

"In Part 1 of this two-part paper the characteristics of mine disasters and their effects are presented with case studies from coal, metal and non-metal mines leading to an amplification of their causes and opportunities for control. The disasters discussed encompass those which threaten the health and the safety of miners and those which affect the general population. In Part 2 of the paper, which will be published in the November 1995 issue of Natural Resources Forum, the approaches to hazard and disaster control are reviewed with particular attention to laws and regulations to promote health and safety at the workplace, and general welfare in mining communities. Further, a systems approach to disaster control is outlined.The mining industry is one of the three basic industries the other two being agriculture, and wildlife and fisheries. It is the process of mining which makes available the riches of the earth - the energy and mineral resources - to benefit humanity. In fact the progress of the human race through the ages is indelibly attached to prowess in exploiting these riches. The stone, iron and bronze ages are markers not just of a time in history but achievements of monumental proportions in the mining and beneficiation of natural resources. Even in agriculture, the remarkable success stories are associated with the prudent use of mined products to enhance production and productivity. The significance of a thriving mining industry to the wealth and security of a nation is therefore unquestioned.Unfortunately, the public's image of the mining industry is often associated with the mining disasters which receive wide coverage in the local and national media. Mine disasters command tremendous attention because of their infrequent occurrence and the extent of human suffering involved. Whether it is an explosion or a fire, or the opening or closing of a mine, the lives of people are touched by the personal and societal impacts of these events.Courts of inquiry of mining disasters have often concluded that the disaster situation was ever present and could have been detected with diligent search. In addition human error has been identified as one of the most frequent immediate causes for the precipitation of the disaster. For the most part, then, mining disasters are caused by man."

Dec 1, 1996

By J. R. Ross

A reconnaissance for sources of scandium and a metallurgical investigation of recovery methods for byproduct scandium from uranium mill solutions were conducted by the Bureau of Mines. The work on scandium was undertaken to obtain information on domestic resources and to explore and develop recovery procedures in consonance with the Bureau's long-range program for conservation and wise utilization of mineral resources. The element scandium is widely distributed in the earth's crust in trace amounts, but it seldom occurs as an important constituent in any mineral. An exception is thortveitite, (Sc,Y)2 Si207) a rare mineral that contains various amounts of scandium and yttrium and may contain up to 42 percent scandium oxide (SC203). Knowledge of the chemistry of scandium has expanded rapidly in recent years (1, 4, 9)4 but only fragmentary information is available about the metal because it is still largely a laboratory curiosity without established uses (2, 3). A recent study shows some of the physical proper-ties of the metal are (1) density of 3.05 grams per cubic centimeter) (2) melting point of 1,540° C, (3) hexagonal close-packed structure) (4) hardness of about 50 Brinell (500-kilogram load), and (5) an alloy behavior similar to yttrium and rare-earth metals (2). The price of $2,850 a pound for scandium oxide of 99.9 percent purity and $2,700 a pound for oxide of 99 percent purity reflects the scarcity and complex chemistry of the element.

Jan 1, 1962

By Elaine T. Cullen

Human beings are natural storytellers and story listeners. We learn very early that stories entertain us, but also give us the ?rules? about what is expected of us and how to make meaning of our experiences. Stories are integral to our lives, and have great power to change or influence how we think or how we react. They are an innate part of how we learn, and have obvious benefits to trainers or educators who are trying to impact what and how we learn. This paper and presentation discuss the social and cultural power of stories, and how they have been used to develop training for skilled blue-collar workers. Included will be examples as well as suggestions for trainers on where to find stories, what type of stories to pay attention to, and how to use them to improve occupational safety training.

Jan 1, 2008

By Robert Bottge

When a company develops a mineral property in a remote area of Alaska, it must consider how best to house its personnel. This Bureau of Mines report examines the economics of two options: company towns and company camps. The price required to maintain a 15% discounted-cash-flow rate of return (DCFROR) was derived for hypothetical 1,000-st/d cut-and-fill mines and 50,000-st/d open-pit mines located in three different regions of the State, One set of hypothetical mines utilizes a townsite; the other utilizes a relatively new concept, a fly-in camp or commuting operation, in which two shifts of employees operate the mine and all associated facilities for 1 week before being replaced by a second crew. The study shows that operating costs were higher for mines employing the commuting option than for mines having a company town because of the additional wages paid for overtime hours; however, the price required to obtain a 15% DCFROR for the single-product copper concentrate, f.0.b. the mill site, was significantly lower owing to the lower investment costs for the camp-type operation. The economic advantage for those mines utilizing the camp increases from south to north and from the coast toward the interior.

Jan 1, 1986

By M. R. Geer, H. F. Yancey

"INTRODUCTION Throughout the history of coal washing, the jig has been one of the most important coal-cleaning appliances. In 1935 34.7 percent of the 45,361,021 tons of clean coal produced was the product of jigging. 4/ Previous to 1928, most of the jigs used in the United States were of the piston type, with which sufficient mobility to allow stratification in bed is imparted by the reciprocating up-and-down movement of a piston in the water compartment adjacent to the screen compartment. In 1928, the Baum type of jig was introduces in this country and has since come into wide spread use. In this type, water pulsations are imparted by application and release of compressed air to the water compartment. All prior studies of the mechanism of seperating cleared coal from impurity by piston-type jigs. 5/ The same laws of settling, of course, apply to both types, piston or Baum, but the character of the separation with the Baum type may be modified more easily because of the flexibility with which air may be handled, as distinguished from the fixed action of eccentrics commonly used in piston jigs. Since no detailed studies are available to show the performance, that is, the character of the separation between coal and impurity, of the Baum type the Bureau of Mines undertook the investigation recorded in this report."

Jan 1, 1938