Search Documents

This report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the ore handling stream. Oversize ore causes much additional labor, creating work stoppages and is a principal cause of accidents in metal mines. This report includes data on block caving, back cut and fill room and pillar, shrinkage stoping, and sublevel stoping.

Jan 1, 1974

By J. P. Capp

This experiment, one of a series on underground gasification of coal, was an investigation by the Federal Bureau of Mines of hydraulic fracturing as a means of increasing the air acceptance of a coalbed to permit introducing combustion air and removing product gases. Specific objectives of the investigation included: (1) Fracturing a coalbed; (2) determining the distance the coal was physically affected; (3) ascertaining the effect of the fracture on air acceptance of the coalbed; and (4) gasifying the coal. The coal was fractured with a fluid consisting of 15,000 lb. of sand mixed with 10,000 gal. of fuel oil and 5,000 gal. of kerosine, injected at pressures up to 900 p.s.i.g. and rates up to 425 g.p.m. The oil served as the fracturing medium, and the sand as a propping agent to hold the fracture open. From the fracture point, (the place in the bed where the fluid was injected), the fracture extended 200 ft. or more along the face cleats, somewhat less along the butt. cleats, and was confined to the coalbed. At the fracture point, the bed accepted about 500 std. c.f.m. of air, which was an etghtyfold increase. Fracture effects were extensive, as airflow was noted from old mine workings and outcrops 600 to 800 ft. from the fracture point. It is probable the actual fracture was much less than 600 ft. and that normal coalbed permeability beyond the fracture limits was responsible for this flow. This indicated that effects of the fracture extended beyond the area of coal physically affected. Although no attempt was made to gasify coal more than 200 ft. away, these effects plus the natural permeability of the bed likely would permit combustion beyond the outer limit of the fracture. As these experiments continued for more than 2 years, and greater air acceptance due to the fracture was observed at the beginning of each test, it is apparent that the effects of the fracturing persist for a considerable time.

Jan 1, 1960

By L. J. Defferding

This report documents the work performed by Battelle-Northwest and its sub-contractors in Phase I of a project to develop a cross pit conveyor system for the Bureau of Mines. The conveyor system description includes details of the conceptual design as well as system and component specifications. The selection of primary and back-up sites for system demonstration is discussed. Maneuvers and operating sequences required for mining the selected demonstration site are described and illustrated in detail. Economic viability of the cross pit conveyor system was analyzed by estimating the cost of overburden removal per ton of coal using the Battelle-designed concept and comparing these costs to the cost of an available state-of-the-art 30-yd3 dragline operation. Testing and trade-off studies conducted are documented and the results presented. Alternate designs considered in developing the selected cross pit concept are included for completeness. Based on the evaluation of the selected concept, it was concluded that the cross pit conveyor system proposed by Battelle is a technically and economically feasible overburden handling method with a good potential to improve western coal mining efficiency.

Jan 1, 1976

By P. L. Swanson

Stability analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is Limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this U.S. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 2010

By M. H. Kline, T. J. Ballard

"INTRODUCTION The Cranberry magnetite deposits occur in pre-Cambrian granite-gneiss in a belt extending from 3 miles southeast of Cranberry, N. C., to about 6 miles southwest of Magnetic City, Tenn. The belt forms a curve, elongated to the north, approximately 26 miles in length.The Bureau of Mines investigation has been confined to the eastern part of the belt, comprising the area from Fork Mountain, Avery County, N. C., to the Hcupscup Knob prospects in Carter County, Tenn.The deposits were worked at least as early as 1820. The Cranberry Iron & Coal Co. and its successors operated the Cranberry mine intermittently for about 50 years until 1930, when operations were abandoned.The magnetite rock is amenable to concentration. Numerous laboratory tests and pilot-mill operations have proved that a high-iron, and low-phosphorus concentrate can be obtained by fine grinding and magnetic, separation, the quality of the concentrate depending upon the extent of grinding. The principal objectives of the Cranberry project were threefold.The primary consideration for beginning exploration of the deposits was the need for developing additional deposits of high-grade iron ore during the war and for replenishing the war's depletion of iron-ore reserves for the peacetime economy. The emergency did not permit logical sequence bf development, and it was necessary to begin drilling before the geophysical survey was completed. The first drilling was begun at the Cranberry mine; and the holes were located from the geological data, coordinated with the position of the mine workings."

May 1, 1948

By William H. King

Preliminary examination of the Virgin River manganese deposit was made by C. H. Johnson, Bureau of Mines engineer, in March 1941. During, April and May 8 trenches were dug, a 48-foot inclined shaft was sunk, and 719 linear feet of channel samples were cut. McKelvey and Wiese, of the Federal Geological Survey, completed mapping the deposit, including the entire area of overlying formations comprising the point of land between the outcrop and Lake Mead. The geologic maps, maps, and ore estimates resulting from these examinations formed the basis for a preliminary report by C. H. Johnson, who recommended further exploration by diamond drilling.

Jan 1, 1949

By Louis C. Brichta

The rapid depletion of known deposits of high-grade ore and the need for development of additional reserves, together with increased interest in open-pit mining of low-grade zinc-lead ores in the Tri-State District, led the Bureau of Mines to examine likely mining sites. Underground operations failed to remove all of the ore in a number of areas, and it appeared possible that some of them might be reworked successfully by low-cost open-pit methods. The South Carthage or Hull tract in Jasper County, Mo., was selected by Bureau engineers as favorable for the development of an open-pit mine.

Jan 1, 1949

By E. G. Baglin

As part of an effort to decrease U.S. dependence on imports of critical and strategic metals, the Bureau of Mines investigated three leaching methods for extracting the base metals and recovering platinum-group metals (PGM) from matte prepared from Stillwater Complex flotation concentrates. Because of a limited supply of natural material, synthetic matte of composition similar to matte prepared from natural concentrates was used to devise the extraction sequences. The validity of the sequences was verified with matte prepared from Stillwater concentrates. In two-stage matte leaching, first-stage H2S04 leaching extracted 99 pct of the nickel and iron from the matte but negligible amounts of copper and PGM. Second-stage oxidative leaching with Fe2(S04)3 or FeC13 solubilized more than 98 pct of the copper and no precious metals. Sequential leaching, in which acid and oxidizing lixiviants were added sequentially to the matte without an intervening filtration step, extracted 99 pct of the Fe, Ni, and Cu. A roasting-leaching technique, in which the residue from first-stage leaching was roasted between 360° and 500° C before a second leaching with H2S04, solubilized 98 pct of the copper. The three leaching methods yielded high-grade PGM residues containing more than 98 pct of the PGM in the matte.

Jan 1, 1982

By Clinton C. Knox

To demonstrate the feasibility of unwatering ore reserves previously indicated in the virgin Melrose zinc-lead field in Kansas and Oklahoma, the Bureau of Mines .carried through a pumping project on the Park Walton farm in 1943. Due to success of the undertaking, attention was turned to exploration of other indicated ore deposits and promising areas within that part of the field benefited by .the drainage project, By the middle of 1946, four private mining companies were active in the field; and a considerable output of lead and zinc concentrate had been obtained from the new Park Walton mine and mill. The Park Walton Ore deposit was unwatered by installing deep-well pumps in three holes previously drilled by the lessee. Pumping was continued by the Bureau of Mines at a rate of 2,500 to 1,000 g.p.m. for about 6 months; during this time the local static artesian water-level, originally averaging 108 feet below the surface in the old drill holes was lowered to the 316-foot level, which justified beginning the initial shaft sinking and mine developments. In all, about 750,000,000 gallons of water was pumped by the Bureau of Mines at an operating cost averaging $0.024 per 1,000 gallons.

Jan 1, 1948

By Fei-chiu Huang

The principle of time domain reflectometry (TDR) is being used by the U.S. Bureau of Mines to monitor strata displacements induced by mining. The Northwestern University TDR Signature Analysis (NVTSA) Program was developed under contract with the Bureau to allow for visual comparison of three TDR waveforms quickly and easily. This program is interactive, and on-line help is available. The Northwestern University Remote Control TDR Data Acquisition System and Modification of Tektronix SP232 Host Application Program (NUMOD) was then developed to allow acquisition of TDR wave-forms from a remote cable tester via modem. The NUMOD system utilizes commercially available software while the NUTSA program is available from the Bureau. This report begins with a discussion of TDR principles followed by a description of the NUMOD system. An interactive example of signature analysis is then used to demonstrate features of the NUTSA program.

Jan 1, 1993

By Charles B. Kenahan

A summary of Bureau of Mines research on utilization and disposal of solid wastes is presented, accompanied by an extensive bibliography of related publications. The Bureau's Solid Waste and Materials Recycling Program is directed toward four main areas of research, development, and demonstration: (1) extraction of mineral, metal, and energy values from urban refuse; (2) upgrading and recycling of automotive and related ferrous and nonferrous scrap; (3) utilization and stabilization of mine, mill, and smelter wastes; and (4) recovery and reuse of values from industrial waste products. A contract and grant program that supplements the in-house research and aids in the training of manpower in management of mineral-, metal-, and energy -based solid wastes is also discussed. This publication is an updating of Bureau of Mines Information Circular 8460 issued March 1970.

Jan 1, 1971

By R. Karl Zipf, Z. T. Bieniawski

"Fracture mechanics plays an important role in studies of geologic materials such as rock and coal. Yet fracture data are scarce for rock and most limited or unreliable for coal. A testing system was developed which can apply mixed mode loads to a crack tip in many rocks and geologic materials. It is possible to subject the test specimen to pure mode I, various mixed modes and a nearly pure mode II fracture load. The system is currently used to study the mechanics of fine fragment formation in various coals. Experimental measurements include KI and KII' fracture velocity and acoustic emission.INTRODUCTIONA major research program at The Pennsylvania State University is directed to understanding the fundamental mechanics of fine fragment formation in various coals. The program represents an effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners. The principal source of the respirable coal fragments is the cutting operation which forms and liberates the particles by a fracture process. Present understanding of the mechanics of the events which form and liberate these particles is meager (Cook, 1982).Current knowledge of the fundamental mechanisms of coal dust generation and entrainment in terms of the underlying fracture mechanics is critically needed to improve and possibly control the processes involved. Whether the cutting operation is done with a 'continuous miner' cutting machine, a plow or a longwall shearer, it is fundamentally a problem of mixed-mode crack propagation. When a cutting tool interacts with coal, it causes numerous cracks to propagate through the intact material. Numerous larger fragments are broken free, but another quantity of undesirable fine fragments is also created. The formation of these respirable fragments may be a direct result of the crack propagation process; hence, a thorough understanding of the fracture mechanics of coal is required to minimize production of the unwanted fine fragments.In most rock engineering applications, the rock material properties are of secondary importance to the rock mass properties; however, for rock fragmentation and rock cutting problems, it is rock material properties such as fracture toughness which are of prime interest (Bieniawski, 1980). Several rock cutting and rock failure theories have been proposed, but it is only very recently that fracture mechanics concepts have been successfully applied to the study of rock cutting mechanics. All cutting models seek to predict the cutting forces and the cutter geometry necessary to cause rock breakage and chip formation given some fundamental mechanical properties ~f the rock. Such models have wide applications in drilling, tunnel boring and mining problems. Nelson et al., (1985, 1986) has provided a very useful correlation between the laboratory measured fracture mechanics properties of rock and the performance of the disk cutters on tunnel boring machines."

Jan 1, 1989

By Denis Dwyer

[This paper describing mining, treatment methods, and costs at Plant No. 1 of the Western Indiana, Gravel Co. at Lafayette, Ind., is one of a series on gravel and sand mining being prepared for and published by the U. S. Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to industry as a whole. On the other hand, operating costs are essential to e technical discussion and study of the methods employed, The attention of the reader is specifically called to this differentiation in order that no Misunderstanding of the scope of the cost tabulations shall ensue.]

Jan 1, 1933

By Harold H. Fukubayashi

The effect of various zinc electrowinning solution impurities on the surface morphology of deposited zinc was investigated. Impurities studied included Al, Ag, Cd, Co, Cr, Cu, Ge, Mn, Ni, Sb, Sn, Ti, Pb02, PbSO4, and HC1. Also, the effect of animal glue, gum arabic, and Na2SiO3 additives on the deposited zinc surface structure was studied. Results were compared with deposits from a pure electrolyte consisting of H2SO4 and Zn+2, 200 and 65 gpl, respectively. Zinc was deposited on a Al cathode, 99.9 pct pure, using Pt anodes. Time, temperature, current density, and impurity concentrations were con¬troller The bulk of the tests were conducted at 40° C and 75 A/ft2 (82 mA/cm2). A scanning electron microscope (SEM) was used to examine the surface morphology. X ray diffraction techniques were used to determine crystal orientation and nondispersive X-ray spectrometer analyses were employed in an attempt to locate impurity concentrations on the zinc deposit when pitting or re-solution occurred. The impurities were categorized by their effect on current efficiency, morphology, and apparent mechanism of H2 evolution from the cathode.

Jan 1, 1974

By R. S. McClain

The Federal Bureau of Mines investigated residues from aluminum plants, to determine if carbon could be removed by flotation while recovering fluorine and aluminum compounds for recycling to the reduction process. This publication summarizes studies on samples representing three types of plant waste products, supplied by three aluminum-producing companies. Samples of flue dust, pot skimmings, and pot linings from the various plants all responded to a simple turpentine flotation scheme to reject 90 to 97 percent of the carbon. Aluminum compound recoveries ranged from 42 to 94 percent on the flue dust, were about 95 percent on the pot skimmings, and ranged from 75 to 89 percent on the pot linings. Fluorine recoveries from the same samples ranged from 35 to 63, 92 to 95, and 77 to 86 percent, respectively. The pot linings contained soluble salts of aluminum and fluorine which were recovered by precipitation with sodium aluminate and carbon dioxide gas. Composites of residues from each plant responded to flotation much the same as the individual samples. Aluminum is produced by the electrolysis of alumina in a molten cryolite bath. The electrolytic reduction cell consists of a carbon-lined box containing a pad of molten aluminum which serves as a cathode, a carbon anode, and an electrolyte of molten cryolite in which the alumina is dissolved. Alumina is reduced to aluminum at the cathode, and carbon is oxidized at the anode.

Jan 1, 1961

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

This report describes the activities and publications of the Bureau of Mines Health and Safety Research and Testing Center, Pittsburgh, Pa., for the fiscal years 1960-65. It includes a discussion or work being conducted on roof control, dust explosions, ventilation, health, coal mine fire control, and electrical-mechanical testing, and an abstract of each paper published during the report period.

Jan 1, 1966

By Jon K. Ahlness

The Bureau of Mines investigated technologies for testing the integrity of in situ leach mining wells, as required by environmental regulations. To test for leaks, inflatable packers were used to seal the well casing. Laboratory testing determined that the packers could contain a casing pressure up to 50 to 60 psi (345 to 414 kPa) less than the packer inflation pressure. Single-and double-packer configurations were successfully field-tested in 32 wells ranging from 500 to 530 ft (153 to 162 m) in depth. A rigid pipeline and a hoist truck were used to run the packers in and out of the wells for the double-packer tests, which averaged 2-1/4 h each. In an effort to decrease the time of the rigid-pipe double-packer test. a self-contained trailer-mounted test system was designed and built. It utilizes a winch and steel cable to run the packers in and out of the well and high-pressure nylon tubing for packer inflation. This system was successfully field-tested in eight wells averaging 650 ft (198 m) in depth and resulted in a time savings of 13 pct and an operator-hour reduction of 42 pct.

Jan 1, 1985

By H. Tomlinson

"PURPOSE OF REPORTThe purpose of this report, which is the third of a. series on the coal mines of the Western States, is to give the findings of a study of the causes and methods of prevention of accidents from falls of root and coal in the mines of Lincoln County, Wyo. The three mines covered in this report, referred to as A. B. and C, account- for 9 per cent of the coal production in the county and nearly 9 per cent of the State's total production. For comparative purposes some statistical data are presented bearing upon the relation of injuries to their causes, to tonnage produced, to men employed, to days worked, and to days lost as the result of injuries.FATALITIES IN WYOMINGTo show the necessity for this study, Table 1 given the fatalities that occurred during 1928 in the bituminous—coal mines of the United States, of the State of Wyoming of Lincoln County, and in Mines A, B, and C, followed by a brief description of the Kemmerer coal dis-trict, its coal beds and immediate roof, thickness of cover, dip of coal beds, methods of mining timbering for roof support, roof testing, and supervision. All of these factors must be considered in any plan outlined to prevent accidents resulting from falls of roof and coal.ACKNOWLEDGMENTAcknowledgment is made to the officials of the operating companies for their cooperation and assistance during the study and collection of data to complete this report.GENERAL INFORMATIONLocation and Ownership The mines included in this report are within 18 miles north and south of Kemmerer, Lincoln County, Wyo. (fig. 1), and are owned and operated by various coal companies to supply the domestic, smelter and railroad markets. They are severed by branch lines of the Oregon Shorty Line Railroad Coal production and men employed underground in the three mines are indicated in essential detail in Table 2."

Sep 1, 1932

By C. A. Herbert

The old fatalistic idea that industrial accidents were a necessary part of industry and that little, if anything, could be done about them has been succeeded by realization that a majority of the hazards causing these accidents were man-made and that if they could be recognized most of them could be eliminated and the accidents prevented. Recognition of these facts has brought about substantial reduction of accidents in many coal dines, as well as in other industries. Knowledge of the hazards and their elimination has been obtained largely through a study of individual accidents and the causes which led up to them. With this thought in mind tae available data on coal-mine explosions in Illinois were studied.

Jan 1, 1934