Search Documents

By Jeffrey Y. Foley

Chromite deposits along the Border Ranges Fault in southern Alaska were investigated by the Bureau of Mines. This report, part 1 of a two- part series, describes the deposits. Part 2 describes the mineralogy and the results of metallurgical tests. Fieldwork began in 1981 and continued through 1983. Ninety-four subeconomic podifom chromite deposits in eight mafic-ultramafic complexes were investigated. Previously unreported chromite deposits at Red Mountain on Kenai Peninsula, on Kodiak Island, and near Tonsina are described. Deposits range in size from less than a thousand tons to over 1.25 million tons of contained chromic oxide (Cr203). Grades range from about 5 to 10 pct chromite. Excluding all deposits more than 10 miles from tidewater or existing roads and all deposits containing only chemical- or refractory-grade chromite, about 2,200,000 tons of Cr203 are contained in 41 hard-rock deposits. A placer deposit contains an additional 556,000 tons. These 42 deposits constitute a subeconomic indicated and inferred reserve sufficient to meet the Nation's chromite demands for about 4 yr, or the metallurgical industry's demands for over 5 yr, at 1981 consumption rates.

Jan 1, 1985

By M. D. Marshall

A remote heat-activated stench gas/tracer gas mine alarm system was developed to reduce the time between fire detection and personnel notification. The stench gas/ tracer gas system contains ethyl mercaptan for personnel warning and a fluorocarbon for tracer gas detection by instrumentation. A system was also developed which can be interfaced with multiplex mine phones. In-mine tests were conducted and several systems are presently installed in a hard rock mine.

Jan 1, 1983

By D. K. Ingram, P. Jurovcik

The National Institute for Occupational Safety and Health (NIOSH) identified hearing loss as the most common job-related disease in the United States in its 1996 National Occupational Research Agenda. Previous studies by NIOSH have shown that operators of surface drill rigs without cabs are commonly exposed to A-weighted sound levels exceeding 90 dB. During hammer-drilling, A-weighted sound levels exceeding 100 dB were recorded at the operator station. NIOSH collaborated with a local drilling company to design and install a partial cab between the operator and the drill steel in an effort to reduce the sound level at the operator station. Sound level measurements in the field show the partial cab reduces the A-weighted sound level by 5 to 9 dB at the operator’s left ear and 2 to 5 dB at the operator’s right ear while hammer-drilling. This paper briefly discusses the preliminary design of a cab and the testing of materials for construction of the prototype. An explanation of the ideas behind the prototype design and fabrication are covered. Finally, the field test method and results are discussed in detail.1

By R. J. Marek

The number of persons fatally injured in the California petroleum industry in 1931 was 30, a decrease of 20 fatalities or 40 per cent from the number killed in 1930. As a result of the decrease in the number of fatalities for 1931, the fatality curve of the California petroleum industry reached its lowest point in nine years. Although reductions in personnel--which permitted the retention of a select and experienced class of workmen, decreased active field-development work, and curtailed production--undoubtedly have had a marked effect on reducing the number of fatalities in 1931, the decrease also has resulted from continued accident-prevention efforts. Statistics show that a direct relationship exists between development activity and the number of men accidentally killed in the drilling and producing division of the California petroleum industry. For example, when the average number of drilling wells in 1930 was 29 per cent less than in 1929, the number of men accidentally killed at drilling wells dropped 48 per cent; and when the average number of drilling wells in 1931 decreased 52 per cent from 1930, the number of fatalities at drilling wells decreased 58 per cent. The relationship between field-development work and fatality frequency is significant because each year at least 50 per cent of all the fatalities in the California petroleum industry occur in the drilling and producing division. This relationship should serve to guide the accident-prevention efforts of the industry, especially in the drilling and producing division, toward checking an increase in fatal accidents when development activity again takes an upward trend.

Jan 1, 1932

By M. Mahan, D. D. Blue, O. C. Garst, F. Fraas, L. Fink

"Early in World War II it became apparent that the known bauxite re- serves might not be adequate to supply the demands of the American aluminum-producing industry, as the transportation of bauxite from abroad to this country might easily be interfered with by hostile action. Consequently, the Bureau of Mines set up an intensive, well-integrated program for the production of cell-grade alumina from low-grade domestic ores. This pro-gram of investigation covered the production of alumina from clay, alumite, red mud, and other low- and marginal-grade ores. In line with the Bureau's usual policy of conservation of natural resources, it was decided that the investigation should be extended to cover the production of alumina and other valuable byproducts from aluminum dross.Statistical information showed that during the year 1943-44, an average of 2,900 tons of aluminum dross was generated monthly. This dross, after partial removal of free metal, had an average metallic aluminum content of approximately 9 percent. Some of this dross was produced by the melting of alloyed aluminum; but a large proportion 1,700 out of 2,900 tons - was generated by two producers of primary aluminum, and the dross did not contain an great proportion of alloying metals. Compared with dross from other sources, this 60 percent of the country's capacity can be assumed to have relatively uniform composition. Moreovcr, the problem of collection and distribution can be minimized because of the relatively small number of plants included in the organization of these two producers of virgin metal.Except for large pieces of metallic aluminum that easily can be mechanically separated for remelting, this dross has been discarded and scrapped. Inasmuch as chemical analyses show that the alumina content of dross is far higher-than ordinary ores - 111 percent alumina equivalent in dross compared to 57 percent alumina in bauxite - aluminum dross is a far richer source of aluminum than any known naturally occurring ores. The discard, of this waste material during the war and reconversion periods would be unsound economically. The work reported herein describes tests at the College Park Station of the Bureau of Mines on the recovery of metal, alumina, ammonia, methane, and abrasive-grade corundum from dross."

May 1, 1946

This project, "Analysis of Men, Materials and Supplies Handling Systems in Underground Metal and Nonmetal Mines" documents the productivity and safety aspects of the existing equipment and systems utilized in transporting personnel and supplies from the surface to the underground production work place. The Present Systems Study (this text -Volume II) documents the productivity and safety of existing men and material movement systems for six representative underground metal and nonmetal mines. Identification of common problem areas was performed using recognized industrial engineering techniques. The back-up data for the industrial engineering analysis of each mine is included as respective appendices (Volume III). A summary of the study background material, six mines' problem areas, comparison of problem areas, problem analysis, and solution recommendations are included as the project final report (Volume I), bound under separate cover.

Jan 1, 1975

By J. W. Thompson

LIMESTONE DEPOSITS. Limestone deposits that have not been demonstrated to be of such quality as to give them any substantial value over other limestone deposits of the same region, are not regarded as minerals. Gray Trust Co., In re, 47 Land Decisions 18, p. 20. OIL AS A MINERAL. Oil is a mineral substance and its removal will greatly impair the value of the land from which it is removed. Texas & Pacific Coal & Oil Co. v. Howard. Southwestern 735, p. 737. Tex. Clv. App. 212 OIL AND GAS AS MINERALS OWNERSHIP. Oil and gas are minerals and so long as they remain in place they belong to the owner of the land under which they are found and such owner has the right to explore for the oil and gas on or under his land and when found to remove and possess the same. Kimbley v. Luckey, Okla. - 179 Pacific 928, p. 831. OWNERSHIP OF MINERALS LACHES NO BAR. The owner of minerals in land can not be barred by laches for failing to assert his ownership where his title had not been ques- tioned and his right invaded. No lapse of time bars one's right to property and it is only in case his right has been invaded that it can be barred by laches.

Jan 1, 1920

INTRODUCTION The pager phones used in many underground coal mines are battery- operated, party-line telephones with provisions for loudspeaker paging. The system is two-wire, non-polarized, and is operated by self-contained batteries. Many of the individual units are certified as permissible. Requirements for installation are specified in state and federal regulations, such as in the Code of Federal Regulations, Title 30, Mineral Resources, Part 75. The major federal regulations that affect communication in coal mines are noted below, with a brief description of the subject matter in each of the relevant paragraphs. Refer to the cited paragraphs of Title 30 for explicit details of these regulations. (This brief description is for reference purposes only.) Minimum Requirements (paragraphs 75.1600, 75.17 13-2, and 75.1003-1) Approved telephone or two-way communication will be provided between the surface and each main shaft landing and each working section ; to the nearest medical assistance; and shall be protected from contact with trolley wires or trolley feeder wires. Installation Requirements (paragraphs 75.5 16-2, 75.52 1, and 77.508-1 ) Communication wires will be supported on insulated hangers, attached to messenger cables, or buried, to protect against mechanical damage ; installed opposite trolley wires; and insulated near power conductors . . . each cable will have lightning arresters within 100 feet of going below ground . . . and arresters will be provided wherever telephone wires enter a building. Wire and Cable Requirements (paragraphs 75.5 16-2, 75.5 17, and 75.52 1) Communication cable means two or more insulated conductors, covered by an additional abrasion-resistant covering; power wires and cables shall be adequately insulated and fully protected; and lightning arresters shall be connected to low-resistance grounds, more than 25 feet from neutral grounds.

Apr 1, 1975

By W. G. Freeman

This study provides recommendations for improved safety in underground blasting procedures based on in-mine observations of blasting practices in 30 underground metal, non-metal, and coal mines, and the analysis of blasting accidents since 1970 and existing state and federal regulations pertaining to the storage and use of explosives. Results of these analyses and observations indicate that 1) blasting accidents have declined but are an important contributor to the hazards of underground mining; 2) existing regulations are essentially adequate; 3) greater emphases should be placed on human errors and unsafe practices and the enforcement of existing regulations; and 4) future revisions of these regulations and standards should be organized, and their intent coordinated to eliminate ambiguities.

Jan 1, 1980

By Roger A. Dworak

This report describes in detail the work done on the development of the Time Domain Reflectometry Microcomputer (TDRM). Modifications to the FMC-Model 302A Cable Fault Locator is described in Appendix D. The TDRM unit uses an 8080 microcomputer to accurately locate major faults in low capacitance cables to within ± 1 foot when properly calibrated. Major faults in high capacitance cables are usually located within ± 5 feet. The upper limits of fault detection are <1 kilohm shunt fault and >7 ohm series fault. In practice fault detection limits are reduced to <300 ohms shunt fault and >30 ohms series fault because of discontinuities caused by cable repair.

Jan 1, 1977

This list is part of the long-range conservation program of the Bureau of Mines and is intended for use by those interested in the Bureau&apos;s publications dealing with oil shale and shale oil. The items included represent 51 years of research by Bureau of Mines employees on oil shale and shale oil and are available at any U.S. depository library. DISTRIBUTION U.S. Bureau of Mines report series contain both free and sales publications. An asterisk (*) designates publications for sale. Such publications can be obtained from Superintendent of Documents U.S. Government Printing Office Washington, D.C. 20402

Jan 1, 1969

By D. E. Sullivan

The Bureau of Mines investigated the availability of potash from 68 mines and deposits in 12 market economy countries (MEC&apos;s) containing, at the demonstrated resource level, approximately 11.7 billion metric tons (mt) of potash in assay terms of contained K2O; K2O as used by industry as a standard of comparison for the different forms of potash. These resources include almost 190 million mt in the United States, 9.63 billion mt in Canada, approximately 430 million mt in Western Europe (France, Federal Republic of Germany, Italy, Spain, and the United Kingdom), 1.24 billion mt in the Middle East (Israel and Jordan) and over 220 million mt in other countries (Brazil, Chile, and the Congo). This analysis his determined that future production of potash in MEC?s will most likely continue to be from the large resources associated with producing operations in Canada. Based solely on the demonstrated resources included in this study, potash mining in the United States would decline while overseas production from MEC&apos;s can continue into the next century at near current production levels. However, timely development of new or inferred resources would offset any such decline. Producing mines in Canada have the resources to increase and maintain increased production well into the next century. For U.S. potash users, Canada is a long-term stable and secure source.

Jan 1, 1986

By Russell R. Trengove

In order to extend or delimit the known ore reserves adjacent to the Comet Coalition property on the western slope of the Highland Peak Range about 8 airline miles west of Pioche, Nev., the Bureau of Mines undertook an exploration project of diamond drilling. Production figures from this property, formerly known as the Schodde, are not available, but it has been reported that small amounts of rich silver and gold ore were Shipped by wagon to a smelter in the Salt Lake valley during 1900-1910. Small shipments were reported for the period 1915-1927, also. A study of the Pioche District by the Federal Geological Survey in 1942 and 1943 was the basis for the exploration program of the Bureau of Mines in 1947 This program consisted of diamond-drilling three holes. The total footage was 2,967 feet. No. 1 hole was drilled 1,260 feet, a record depth for diamond drilling in the Pioche District. Silver-bearing lead-zinc sulfide ores are found in the Combined Metals limestone, known locally as the C.M. bed, These deposits have been formed by replacement of the limestone that is inclosed in the Pioche shale.

Jan 1, 1949

By Russell J. Foster

Many important materials are derived entirely or partially as byproducts of primary copper, lead, and zinc production. This U.S. Bureau of Mines report examines the collective role of byproducts with regard to the economics of domestic mineral production, and their individual significance in terms of dollar value, end uses, and strategic considerations. The study also analyzes circumstances that have affected the competitiveness and structure of the U.S. copper, lead, and zinc industries, and factors that impact byproduct availability. These factors include production capacity at smelters and refineries, process technology, changing sources and composition of ores, regulations, foreign ownership, and byproduct demand and price. Policy considerations regarding stockpiling, regulations, and research are assessed.

Jan 1, 1991

By Lloyd Williams

1. The investigation shows that the Poplar Creek and Big Mary beds contain the largest known recoverable reserves of coal in Morgan County, Tenn. The Poplar Creek bed has been the most productive. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 96 million tons, as of January 1, 1954. Of this total, 59 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By Harold M. Smith

This report presents a complete qualitative picture of knowledge of the composition of petroleum as of April 1965. The material is presented in detai 1 on two imaginative maps--one, the Hydrocarbon Hemisphere, depicts the hydrocarbons that have been identified in petroleum; the other, the Heterogeneous Hemisphere, shows the sulfur, nitrogen, and oxygen compounds that have been found. All compounds are placed on the maps according to boiling point. The accompanying text illustrates by structural formulas the several types of hydrocarbon and nonhydrocarbon compounds identified, presents some quantitative data, and points out the possible geochemical significance of a number of the compounds. The possibilities of the Petroleum World of the future are discussed as a function of needed research.

May 1, 1965

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944

By C. W. Davis

During the second year of its existence, the Ore-Testing Section has actively prosecuted work in the standardization of testing methods, in conducting routine tests and analyses for other Government agencies, and in the determination of recommended processes for the treatment of representative ores from mining districts. Close cooperation has been maintained between the members and units of this Section and those of other Sections, J. A. Woolf and J. B. Clemmer have continued to act in an advisory capacity and R. E. Head has contributed valuable assistance in the microscopic examination of ores and metallurgical products that did not respond readily to standard treatment methods.

Jan 1, 1938

By C. W. Davis

During the second year of its existence the Ore-Testing Section has actively prosecuted work in the standardization of testing methods, in conducting routine tests and analyses for other Government agencies, and in the determination of recommended processes for the treatment of representative ores from mining districts. Close cooperation has been maintained between the members and units of this Section and those of other Sections. J. A. Woolf and J, B. Clemmer have continued to act in an advisory capacity and. R. E. Head has contributed valuable assistance in the microscopic examination of ores and metallurgical products that did not respond readily to standard treatment methods.

Jan 1, 1938

By D. E. Redmon

The Federal Bureau of Mines has studied the locations and general features of 90 pegmatites found in north-central New Mexico. The dominant valuable product of the pegmatites is muscovite, both sheet and scrap. However, the Harding pegmatite in Taos County is mined only for beryl. Many attempts have been made to recover scrap mica on a large scale by mechanical beneficiation of pegmatite, but the operations heretofore have been short-lived. The Globe mine and the Apache mine, both near Petaca in Rio Arriba County, have been the most important sources of sheet mica in New Mexico. Recognition of the growing need for some of the minerals derived from pegmatites led the Bureau of Mines to investigate the occurrences of pegmatite.

Jan 1, 1961