Search Documents

The 1967 Lignite Symposium was held at Grand Forks, N. Dak., on April 27-28, 1967. This was the fifth of these technical meetings and the fourth which was cosponsored by the University of North Dakota and the Bureau of Mines. These symposia have provided a meeting place where current developments concerning technology and utilization of solid fuels (lignite) are presented. There was a registration of 255 persons from 24 States, the District of Columbia, six Canadian Provinces, Germany, and India. Many segments of coal or energy oriented organizations at many levels were represented. During the meeting, 18 presentations were made covering developments in electrical power generation, mining, estimation of reserves, combustion, gasification, and chemical and speciality uses of low-rank coals; these are com-piled in this Information Circular to provide a record of the symposium and to permit wider dissemination of the information. Proceedings of the other meetings have also been published.3

Jan 1, 1968

Study to develop a new and more cost effective equipment system, incorporating a winch-pulled dozer blade, for leveling spoil and performing reclamation of area strip mines.

Jan 1, 1975

By B. W. Gandrud

In July 1948, the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and mine operators, published Report of Investigations 4306, "A Combination Cleaning and Dewatering Process for Treating Fine 'Sizes of Coal, Preliminary Report In this report a new process, referred to as kerosene flotation; was described, and results of experimental work with the process Previous to the fall of 1947 were given, The contents of the report. were summarized on pages 19 and 20' as follows: In coal-preparation plants using wet methods of cleaning, the most difficult problem is the cleaning and dewatering of the "fines" from about 10-Mesh to 0. A combination proceed is now under investigation that shows promise of practically and feasibly solving this problem. The process is similar to froth flotation, but a generous quantity of kerosene is used as one of the reagents, and the feed is from approximately 10-mesh to 0 considerably coarser than the usual froth flotation feed. The kerosene and the coarseness of the reed result in a floated product that, under certain circumstances, can be dewatered satisfactorily by a simple process of mechanical squeezing, Squeezing is accomplished by means of an ordinary conveying' Auger-and trough assembly with a section of pipe easing at the outer end of the trough. The bottom of the trough and. casing is fitted with wedge-wire sections to permit escape of the water freed by the squeezing action of the auger. On account of the important role of the kerosene, the process has been referred to in this report as kerosene flotation. Up to now, the investigative work has been divided about evenly between the laboratory and commercial plants. Nearly all of the work has been done on sludges containing the solids from the underflow of dewatering screens. A few runs have been made on 10-mesh to 0: fines from raw coal, but in some of those runs the dewatering mechanism, failed to function.

Jan 1, 1950

By Pamela J. Watson

The U.S. Bureau of Mines has demonstrated in laboratory tests that drilling with surface-charge-neutralizing concentrations of polyethylene oxide (PEO) polymer solutions simultaneously improves penetration rates and extends bit life. The applicability of this additive to improve drilling performance in coal measure rocks was demonstrated under field conditions at an abandoned mine land site in Pennsylvania and a producing coal mine property in Ohio. Penetration rate improvements ranging from 15 to 50 pet were obtained when core drilling through a variety of coal measure lithologies. Drilling cost analysis indicates that the small added cost of using the polymer is more than offset by the savings that result from demonstrated increased drilling penetration rates, which translate into drilling cost savings of about 10 to 30 pct. This report also gives chemical analyses of a variety of coal measure rocks and some corresponding local drilling water samples, obtained from a wide geographical base, along with threshold concentrations of PEO required to effect the improved drilling performance in these rocks. From these data, the threshold PEO concentrations needed to ensure improved drilling performance can be estimated for any coal measure rock suite. Proper techniques for mixing PEO solutions are also presented.

Jan 1, 2010

By D. Harrington, C. W. Owings

The mining industry is gradually realizing that safety education and safety inspection are economic factors that may not be overlooked as a means of reducing operating costs . Many mine operators , however , have failed to realize the benefits of safety , and the efforts of the more progressive mining companies are offset by the carelessness of neighboring companies when the accident records of a community or a State or the nation as a whole are considered . This tendency is indicated by the data collected by the safety division of the United States Bureau of Mines . During the fiscal year ended June 30, 1930 , relatively definite information: was secureä concerning 34 mine explosions , 24 mine fires , and 29 miscellaneous accidents ; these accidents are by no means all of the explosions , fires , and miscellaneous accidents which occurred in the mines of the United States during the period; but the data on the fires and explosions constitute a record of all of those types of accidents that were called specifically to the attention of the safety division , and the miscellaneous accidents include those on which definite , detailed data were obtained by the safety division .

Jan 1, 1931

By M. R. Geer

This report presents the results of washability examinations of seven coals from the principal coal-producing fields of Montana. A complete performance test of the Baum-type jig operated at one of the mines is included, as are the results of cleaning tests made on two of the coals in a dense-medium pilot plant. The coals examined from the Red Lodge, Bull Mountain, and Forsyth fields are comparatively easy to clean. Ash contents of 5 to 10 percent can be obtained at yields of washed coal ranging from 90 to 95 percent. The coal from the Great Falls field, however, could not be cleaned readily to less than 14 percent ash, and the rejection of impurity would amount to over 25 percent. The two coals treated in the dense-medium pilot plant were characterized by sharp separation of impurity, high recovery efficiency, and satisfactory reduction in ash content.

Jan 1, 1955

By William D. Monaghan, Michael A. Trevits

Over the period 2000 to 2003, roof falls have accounted for 4 to 14% of the fatalities in underground mining operations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the frequency, exposure, and risk of these events through an ongoing program of field and laboratory studies. One area of research involves the evaluation of polyurethane grouting technology that is commonly used to stabilize fractured mine roof strata. Concurrently, NIOSH is conducting work to evaluate the application of ground penetrating radar for advanced delineation of problematic mining areas. In this study, NIOSH partnered with Sub-Technical, Inc. who injected a polyurethane grout (also known as glue) into a roof area of NIOSH’s Safety Research Coal Mine. The mine roof area was scanned using ground penetrating radar technology before and after grout injection in an attempt to determine the extent of grout infiltration. A comparison of the pre-and post-grouting radar records showed a significant change at a mine roof depth of about four to five feet. The interpreted radar records were then compared with drill core information, borescope evaluation of roof-bolt holes in the study area, and underground observations. At this site, the interpretations of the radar records correlated with data obtained from the core holes, borescope evaluations and underground observations. This study showed that ground penetrating radar technology can be a useful tool for detecting changes in mine roof due to the injection of the grout.

By McHenry Mosier

This progress report on a national survey of the use of detachable bits in metal mines covers 10 mines. It presents comparative costs for drilling with conventional and detachable bits, describes the reconditioning of drill steel, and gives various data on rock drilling at these particular mines. Reports to follow will include similar data on drilling at other metal mines in the United States. ACKNOWLEDGMENTS This report is based on costs and data developed and furnished by the operators of the mines visited. The author is greatly indebted to the officials and staff members at these mines for their cooperation and assistance.

Jan 1, 1936

By P. L. Swanson, F. M. Boler

The U.S. Bureau of Mimes conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic destressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 21/2-week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 1993

By By Staff

"Acid mine drainage can be controlled by water treatment, retardation of the pyrite oxidation reaction system, or enhanced prediction that allows preventive action to be taken. The Bureau of Mines is conducting research in each of these areas; the results of this research are summarized in the eight papers that comprise this volume. Field work to evaluate overburden analysis, alkaline injection, and bactericidal control of acid formation is described, along with two new inexpensive methods to treat acid mine water. These papers were prepared for an acid mine drainage technology transfer meeting held in Pittsburgh, PA, on April 3 and 4, 1985. INTRODUCTIONAcid drainage from coal mines is one of the most persistent industrial pollution problems in the United States. Over 5,000 miles of streams and rivers are adversely affected, primarily by underground mines that have been abandoned for decades. Meanwhile, at active mining operations and at sites where mining occurred after 1977, discharge water must be treated to meet fairly stringent regulatory limits--at a cost to the industry of over $1 million per day.The Bureau of Mines has a special responsibility to facilitate integration of mining and mineral processing with environmental safeguards. This responsibility is twofold: the development of techniques to reduce or eliminate environmental degradation, and the improvement of existing pollution control processes to make them more efficient and more cost effective. Research in acid mine drainage exemplifies the Bureau's concern for these environmental aspects of mining.This collection of papers summarizes much of the Bureau's recent research on acid mine drainage and will give the reader a sense of where the research is headed, in addition to providing details regarding new technology and recently acquired knowledge. The research papers address four basic objectives:"

Jan 1, 1985

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

By Wilbur A. Haley

One of the purposes of the investigation was to determine and report on how coal augers are used to mine bituminous coal that is near outcrops and may not be mined otherwise by any other present-day method. Such increased overall recovery results in the conservation of coal resources. Other reasons for the investigation were to determine and report the production rates of such operations and the types of equipment used. Auger mining of coal as a means of coal recovery supplementary to strip mining has been introduced and developed since World War II. This type of coal mining has grown rapidly, and bituminous-coal production by auger mining has been estimated at 6,000,000 tons in 1955. Mines were selected for study to give reasonably representative information on auger mining in different types and thicknesses of coal beds in different geographic areas and on different types and sizes of equipment operated under various conditions. This report is based on field studies of 8 auger-miming operations in Pennsylvania, West Virginia, and Ohio and in 5 different coal beds. Operations were observed in active strip mines, in strip mines reopened for auger mining, and along benched coal-bed outcrops. At the time of this study, no augers were reported to be operating in underground mines. The diameters of holes drilled ranged from 26 to 52 inches, and the lengths of holes ranged up to 208 feet. At some operations auger holes often penetrated abandoned underground mine workings.

Jan 1, 1957

By Geoffrey C. Huggins

Diagnostic: tests were performed on a production ST-5A Load-Haul-Dump machine manufactured by Wagner Mining Machinery Company to evaluate and rank order noise sources. The diagnostic evaluation indicated that the major noise sources were the transmission, the engine, and the cooling fan. This phase was followed by implementation of recommended noise control treatments, which included vibration isolation of the transmission, a transmission enclosure, an engine enclosure, and modifications of the inlet to the cooling fan. The final step in the program was an underground operational period which began on 31 August 1976 at the National Gypsum Mine in Shoals, Indiana. The noise control treatments successfully reduced the LHD operator noise exposure by 7 dB(A), thus increasing its allowable operation time by a factor of 2.7. Actual measurements made underground using noise dosimeters have indicated that, during, a typical shift, the noise control treatments have reduced the fractional exposure to an allowable level. The report discusses the mechanical aspects of the LHD, its noise sources, the treatments applied, the final levels achieved, and field experience with the noise-controlled machine.

Jan 1, 1977

This report is a compilation of all information obtained in accordance with the requirements of contracts S0122076 and H0232056. A series of eight coal mines were visited to determine their communications usage and requirements. Presently available equipment was surveyed and evaluated to determine its applicability to the needs of the mines. The equipment studied includes that made by the following companies: Anaconda Telecommunications Division Andrew Antenna Bendix Communications Division Collins Radio Group of Rockwell International Executone Communication and Sound Systems Gai-tronics Mine Safety Appliances Company Motorola Communications and Electronics, Inc National Mine Service Company Plessey Communications Systems Corp Pye Electronics Limited Reach Electronics Set Com Corporation Sonex Incorporated

Jan 1, 1974

By Rena I. Geroyan

This U.S. Bureau of Mines report presents an evaluation of the coal mining industry's impact on the economy of Pike County, KY. A software package called IMPLAN was used to perform the analysis. The results of this study show that coal mining was the primary income producing industry in Pike County in 1990, accounting for about 46% of the county's Total Industry Output, and 21% of the total employment.. Coal production in that year amounted to 29.6 M mt (32.6 M st). Two alternate economic scenarios were developed to study the potential effects of changing coal market conditions on the county. Scenario A assumes market changes result in a coal production increase of 4.5 M mt/yr (5.0 M st/yr), and scenario B assumes a decrease of 4.5 M mt/yr (5.0 M st/yr). Scenario A would result in a 15.3% rise in the value of Pike County's Total Industry Output, adding a total of 1,663 jobs (+6.1%) in all sectors in the county. Scenario B would have the opposite effect, decreasing the Total Industry Output and employment by identical amounts. Such knowledge would allow local and regional officials to anticipate the economic and social impacts of shifts in coal production, and plan accordingly to mitigate impending changes.

Jan 1, 1994

By Wendell R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems in developing urban areas. Uncertain knowledge of abandoned coal mines also imposes potential hazards in coal excavation operations since water inundation or the release of methane gas is a pricnipal hazard when mine excavation operations break into an abandoned mine. U.S. Army requirements for an effective method for detecting and mapping subversive man-made tunnels have resulted in a surface-operated automatic earth resistivity survey system with a digital computer data processing system. Field tests aimed at demonstrating the system performance resulted in successful detection of tunnels having depth-to-diameter ratios up to 15 to 1. Under the sponsorship of the Bureau of Mines, a similar system was designed and constructed for use in the detection of coal mine workings. This report discusses the hardware and software aspects of the system and the application of the high-resolution earth resistivity method to the survey and mapping of abandoned coal mine workings. In the field tests reported, the targets of interest were both air-filled and water-filled workings.

Jan 1, 1980

By William L. Crentz

Early in the nineteenth century, coal from Clearfield County entered the eastern commercial market. Ashley reports that coal was moved down the Susquehanna River by ark from Clearfield to Columbia, a distance of 260 miles, as early as 18o4. Around 1850, the famous Moshannon or Lower Freeport bed was discovered. Several years later the Moshannon Basin was developed extensively, and the coal from this area soon acquired an enviable reputation as a high-quality industrial fuel. Today much of the original Moshannon Basin coal is worked out, and the Lower Kittanning bed has replaced the Lower Freeport bed as the principal source of production in southeast Clearfield County. With depletion of the thick underground deposits, the importance 'of Clearfield County as a coal Producer would have diminished rapidly, if it had not been for strip mining the thinner beds. About 60 percent of the coal produced in the county is strip-mined, and the trend toward this mining method is expected to continue as the older underground operations are exhausted. Many strip mines are working in beds that are too thin to be recovered economically by any other method.

Jan 1, 1952

To allow routine measuring of the exposure of underground workers to N02 from diesel engines and residual gases from blasting. The Approach: A miniature sampler absorbs NO2 which can be measured using a simple method adaptable to both multiple automatic analyses or individual on-site analysis. How It Works: The NO2 sampler is encased in a plastic tube approximately half the length of an ordinary ball point pen and clipped to an underground worker's hard hat. Removal of the end cap activates the personal sampler. Air from the working place enters the open end and diffuses at a controlled rate down the tube interior. The diffusion rate is dependent on tube dimensions (ratio of cross-sectional area to length). The closed end of the tube contains stainless steel mesh which is coated with triethanolamine (TEA) for absorbtion of all NO2 reaching it. Other oxides of nitrogen are not absorbed. The amount

Jan 1, 1975

By K. C. Dean

The Bureau of Mines, following passage of the Solid Waste Disposal Act of 1965, was authorized to conduct research on methods for utilizing, stabilizing, or reclaiming mineral wastes. This report summarizes laboratory research conducted by the Bureau and cooperative field studies made with the mineral industry to reduce the environmental impacts of air and water pollution deriving from mineral wastes. Utilization research showed that both dry-press and steam-cured building bricks and ceramic tile could be made from copper mill tailings and other discarded mineral wastes. Sponge iron was produced from steel mill and amination industry wastes, and valuable mineral products were extracted from such diverse sources as flue dusts and uranium tailings. Mineral wastes were combined with agricultural and/or sewage wastes to make artificial soils that have the potential of resolving several disposal problems by production of a useful commodity. Physical, chemical, and vegetative stabilization methods were evaluated, singly and in combination, for reclamation potential on copper, uranium, lead-zinc, and asbestos tailings. Suitable methods were developed in the laboratory for overcoming major adverse conditions of these wastes such as salinity, heavy metal toxicity, acidity, basicity, lack of nutrients and organics, and unstable surfaces. Field testing of these methods was performed on a variety of mineral wastes. Costs for the various stabilization and utilization-procedures developed were also determined.

Jan 1, 1986

By Kenneth J. Miller

The Bureau of Mines two-stage coal-pyrite flotation process was modified to provide a more concentrated final clean coal slurry underflow which could be dewatered economically by filtration or centrifugation. This was accomplished by doing the first-stage coal flotation step in the conventional manner with a slurry of about 8 percent solids, but running the second-stage pyrite Flotation step with undiluted coal froth concentrate containing about 25 percent solids. The final clean coal underflow produced by the new technique contained between 26 and 30 percent solids; this pulp was sufficiently concentrated to be filtered industrially without further thickening. Sulfur removal was equal to that obtained using dilute second-stage pulp,

Jan 1, 1975