Search Documents

By Ernest A. Curth

The Bureau of Mines studied pressure changes in coal pillars by using encapsulated hydraulic pressure cells to measure relative changes in stress developed during mining. The data indicate that (1) abutment stresses were detected when the pillar line is within 42 to 100 feet, (2) vertical pressure increases as coal is mined in the pillars, (3) at first pressure is higher at the edge of the pillar than in the core, but as mining progresses, the higher pressure is measured in the core of the stump, and (4) in the two instances where lateral pressures were measured, they remained lower than the vertical pressures during pillar extraction. The data also indicate that the mean vertical pressure increase, 6P, in a pillar is roughly related to the percent of pillar extracted, A, by the empirical parabolic equation

Jan 1, 1967

By G. R. Hopkins

Although many small refineries were dismantled in 1934 the total number of plants, including a few under construction, increased from 604 at the beginning of the year to a new high of 638 on January 1, 1935. The capacity also reached a new record, the total of 4,072,400 barrels of crude oil daily being about 45,000 barrels higher than the previous high of January 1, 1932. The number of refineries increased materially in 1933, following construction in east Texas and the building of many small plants in the Rocky Mountain district and elsewhere. Most of the new plants of 1933 were built to provide an outlet for crude or because the ratio between crude oil and gasoline prices appeared conducive to profits However, low gasoline prices and increased costs in 1934 dispelled the hopes for profits; many plants were shut down, and some were dismantled. The number of operating plants declined from 454 on January 1, 1934, to 435 on January 1, 1935, but the number of inactive plants increased from 137 to a new high of 196 during the same period. As indicated above, new construction was at a minimum in 1934, and on January 1, 1935, only 7 plants were being built.

Jan 1, 1935

By Erle C. Donaldson

Subsurface injection of liquid and slurry-type industrial waste is being used as a means of waste disposal. This survey conducted by the Bureau of Mines shows that the method can be economically and environmentally attractive if the proper precautions are taken, especially when the alternative is cursory treatment and discharge at the surface. Attention is called to petroleum technology and experience that can be applied to subsurface waste injection. Part 1 of this report is a discussion of the general aspects of subsurface waste-injection systems. Part 2 is a general discussion and review of the literature concerning the geologic formations available for injection in the United States. Part 3 is a discussion if 15 case histories including information on the source and nature of the waste and the geology, surface equipment, well completion, and operation of the systems.

Jan 1, 1974

By Manuel Gomez

This report presents low-temperature tar data from studies by the Bureau of Mines of tars produced in an externally heated (entrained state) pilot-plant-scale retort. Analytical data covering 20 low-temperature tars, derived from the. carbonization of various ranks of foreign and domestic coals, are tabulated. The character of the tar is discussed in relationship to carbonizing conditions and the rank of coal. It is seen that in carbonization techniques that employ entrainment or fluidization of the coal particle, carbonization conditions are secondary to coal rank with respect to tar-oil yields and composition. The influence of distillation conditions on recoverable yields of tar products is presented. The probable yield of commercially important chemical products, based on a ton of pure (moisture- and ash-free) coal, are predicted. INTRODUCTION Low-temperature tars produced by entrainment or fluidized carbonization techniques that employ internally heated reactors represent the most nearly primary tart produced by industrial processes. In brief, such a process involves the application of a heat gradient to the coal particle "boiling" or suspended in a turbulent state in the reactor chamber. Conditions are observed so that the coal particle remains suspended within the reaction zone by a gas stream for a time interval commensurate with maximum tar-oil yield. The heat necessary for the carbonization reaction may be obtained entirely from the hot (preheated) gas stream, or it may be derived partly from the combustion of the volatile products and char by the transport gases, usually air. The volatile material moves out of the carbonizing zone at a rate that approaches the velocity of the transport gas. Carbonizing conditions are ideal when a minimum particle residence time is obtained within the reactor at a given temperature and a maximum yield of condensable volatile matter is released. In industrial practice this objective is a compromise.

Jan 1, 1957

By Eugene H. Skinner

The U.S. Bureau of Mines conducted experiments on the use of lightweight concrete in the density range of 100 Ib/ft3 for liners in underground mines. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a second section constructed in a drift using an air-supported formwork. The lightweight concrete in the two underground test sections was placed using piston pumps and a slickline. Fiber reinforcement was added to the concrete in the mine sections without any apparent problems with either pumping or placement of the concrete. In another experiment, the Bureau and Hecla Mining Co., Mullan, rD, used lightweight concrete in the density range of 25 Iblfe to replace timber blocking in a raise preparation structure. Other experiments are described in which low-density, lightweight concrete blocks were produced for mine ventilation doors, stoppings, and barricades. Other mine uses reviewed include pillars and collapsing beams. An advantage of low-density concrete is that it will display up to 50% deformation at a constant yield stress. These hlllovative concepts in deformable concrete lining systems will aid mine operators by decreasing capital and maintenance costs, increasing the available space in underground haulageways, and providing productivity gains and improved resource recovery in the soft, caving, squeezing, or bursting grollnu conditions often found in deep mines.

Jan 1, 1989

By John C. Machisak

Employment and related injury experience of the coking industry in the United States for 1957 contained in this publication is summarized under three general sections: (A) General injury experience: Tables 1 to 9: Current and comparable statistics on operating data, number, frequency, and degree of severity of injuries and major accident agencies involved in the cause of Injuries. Data are presented for the industry as a whole, for each type of oven, and for the States in which coke was produced.

Jan 1, 1959

By Walter R. Storms

"The New Mexico potash exploration described herein was begun in February- 1944 by the Federal Bureau of Mines with the object of determining the amount of potash ore in the United States Potash Reserve in Eddy County, N. Mex., by exploring the deposit from the surface with vertical drill holes. The work was completed in October of the same year after 16 holes had been drilled on the reserve and in the immediate vicinity.The Potash Reserve is located in secs. 26, 27, 34, and 35, T. 20 S., R. 29 E., Eddy County, N. Mex., about 14 miles northeast of the city of Carlsbad. Drilling was done in secs. 26 and 35 of the reserve, in sec. 14 to the north, and secs. 25 and 36 to the east. All work was done on Government-owned, unleased land.The reserve may be reached from Carlsbad by traveling northeast by automobile for about 14 miles on paved U. S. Highway 62. This highway passes through the southern part of the reserve. Other parts may be reached by a State highway which passes along the eastern side of the area, then by poor dirt roads to various drilling sites. A branch of the Atchison, Topeka and Santa Fe Railroad also passes across the southern part of the reserve en route from Carlsbad to the plant and mine of the Potash Co. of America, a few miles northeast of the Project and 22 miles from Carlsbad.Work on the project was greatly facilitated by the help of Ralph H. King, associate geologist, R. K. Bailey, geochemist, H. C. Spicer, geophysicist, Hope Bunker, junior geologist, and R. H Allport, district mining supervisor, all of the Federal Geological Survey; and Charles H. Johnson, who at that time was district engineer for New Mexico for the Mining Branch of the Bureau of Mines."

Apr 1, 1946

By Oliver C. Fursman

These investigations were conducted to determine conditions for recovery of nickel and copper from Funter Bay, Alaska, sulfide ore and recovery of nickel from nickel-silicate ore, Nickel Mountain, Riddle, Oreg. Samples of Funter Bay cupriferous and nickeliferous pyrrhotite ore, were treated by beneficiation, roasting, electric smelting of roasted are for matte production, chlorination, leaching, and sulfatizing roasting with subsequent leaching. Funter Bay and Nickel Mountain ores were smelted together to produce matte. Total sulfide flotation, followed by magnetic separation of the tailings to recover entrained nickel-bearing pyrrhotite, resulted in the highest nickel recovery in beneficiation tests on Funter Bay are. Overall beneficiation resulted in recovery of 98.5 percent of the copper and 95.4 percent of the nickel in the concentrate that contained 3.5 percent copper and 1.7 percent nickel.

Jan 1, 1962

By R. L. Levens

The Underground Injection Control program was promulgated in 1981 by the U.S. Environmental Protection Agency under the provisions of the Safe Drinking Water Act. Placement of mine waste backfill underground is considered underground injection under the provisions of this program. A major issue is whether mine waste that is regulated as a contaminant source on the surface should be disposed of underground. The U.S. Bureau of Mines conducted research to investigate the impacts of mine waste sandfill on the quality of ground water. Analyses of water samples collected before and after contact with sandfill in a 10-year-old stope, as well as samples of the sandfill itself, were used to ascertain the influence of the sandfill after mine closure and subsequent flooding. Computer models supported the hypothesis that oxidation of pyrite by oxygen, accompanied by dissolution of carbonates, was the predominant reaction controlling the quality of the water being discharged from the stope. Concentrations of metals released as a result of acid production remained near or below detection limits. Metals release after mine flooding is expected to remain low as a result of the buffering by the sandfill and the reduced rate of oxidation.

Jan 1, 2010

By K. E. Robinson

Appendix A is an abridged extract of the report prepared by the Geotechnical and Structural Engineering Society of Idaho, and presents the results of their one-year study to evaluate the feasibility of disposing mill tailings by landfill construction. Appendix B describes the field and laboratory testing program completed by RDM to assess the effectiveness of a soil (slimes) liner as a means of seepage control to reduce the introduction of contaminants into the local ground water regime. Appendix C presents a summary of a thesis by Lawrence Martin on the analysis of the acid production potential of mill tailings, and the results of geotechnical testing of mill tailings completed by ROM. Appendix D describes potential landfill sites identified within the study area, the development of these sites to meet the present needs of the mining industry and the future requirements of the community is described. Appendix E summarizes the main legislation impacting on tailings disposal. Appendix F discusses the environmental and socio-economic factors that should be considered.

Jan 1, 1981

By Howard P. Hamlin

This Bureau of Mines report is concerned with the testing procedures for evaluating clays, shales, and slates for lightweight aggregates using the rotary-kiln method of production. To meet the increasing demand for light-weight concrete, rapid, accurate methods for appraising raw materials for light-weight aggregate are needed. Preliminary tests were made on samples of clay, shale, and slate, using laboratory equipment, and the data were used to establish operating conditions for pilot-plant-size rotary-kiln tests. Lightweight concrete was made from the processed aggregates and the properties determined. The results show that the laboratory data can be used to guide rotary-kiln testing, and, with the exception of sampling, a complete appraisal of a raw material for lightweight aggregate concrete can be made in 3 days by the methods described in this report.

Jan 1, 1962

By E. S. Shedd

Amenability studies were conducted by the Federal Bureau of Mines on an electrooxidation technique for the extraction of mercury from cinnabar ores, particularly those that are too low in grade to be furnaced or retorted economically. Oxidation was accomplished by electrolysis of the ore while slurried with brine. Mercury was dissolved through the formation of the soluble tetrachloro mercury complex, HgC142-. Mercury extractions ranged from 90 to 98 percent in 4 to 6 hours of processing time when tests were made on eight different types of cinnabar ores containing from 0.7 to 18 pounds mercury per ton ore. Salt concentration was varied from 4 to 10 weight-percent depending on whether Pb02 anodes and iron cathodes were used or whether graphite was used for both electrodes. Power consumption ranged from 17 to 64 kilowatt-hours per ton of ore treated. Ninety-nine percent of the mercury was recovered from pregnant solutions by precipitation on an active metal such as zinc, followed by distillation of the resulting amalgam at 600° C.

Jan 1, 1975

By Clarence Karr

AN EXTENSIVE characterization was conducted on the neutral oil components in a low-temperature bituminous coal tar. A total of tai individual compounds identified with respect to individual isomers, and at least 55 other compounds were indicated to be present. The amounts were determined in all instances. A comparison of isomeric distribution in the tar with thermo-dynamic equilibrium distribution, and kinetic distributions indicated that the composition of the tar largely reflected the structure of the coal from which it was formed. Detailed descriptions are presented for the separatory and qualitative and quantitative procedures for the characterization of the neutral oil component. These include micro fractional vacuum distillation, displacement liquid chromatography, gas-liquid chromatography, countercurrent distribution, and infrared and ultraviolet spectrophotometry. Descriptions are given for the synthesis of authentic specimens of alkylindenes, The ultraviolet and infrared spectra of 134 polycyclic compounds, ranging from alkylindenes to alkylphenanthrenes, either found in the distillable neutral oil, or thought likely to be present, are also given.

Jan 1, 1967

By S. M. Shelton, F. D. DeVaney, M. M. Fine

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced ; although it is well -known that there are large deposits of low - grade ore in the United States , the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore is depleted through inability to obtain adequate supplies from foreign sources . Consequently, a program of laboratory and pilot - plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines . This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program . The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series , Report of Investigations 3606 , Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent , and C. H. Schack . Other reports will be published as the work progresses .

Feb 1, 1942

"INTRODUCTION These inspection standards have been prepared for use as a guide for the Federal inspection of anthracite mines. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7231 in January 1943 and used as a guide for Federal inspections. Numerous changes in the original standards have been made, due in part to recognition of shortages of some types of safety equipment due to the war, in part to need of additional standards to cover certain mine conditions and practices, and in part to conditions not foreseen when the original standards were prepared.Throughout these standards reference is made to determining the methane content of the mine air by using a permissible flame safety lamp. The Bureau has approved various electrical devices for the detection of methane, but it is recognized that new devices for determining the percentage of combustible gases as well as the percentage of oxygen, might be perfected for general use in mines, and therefore it may be necessary to revise certain standards to include the use of such equipment if and when the device is accepted as being permissible.About one-fourth of these standards are marked with an asterisk (*) as being of particular importance in preventing accidents in many coal mines; however, failure to carry out the suggestions made in such of the other standards as are applicable may also lead to loss of life.With continuing change in mining methods, some of these standards may become inapplicable, and further revision will be advisable. Therefore, question regarding these standards and suggestions regarding new standards should be brought to the attention of the Bureau, so that changes may be made from time to time. Numerous changes proposed by mine operators and by State mining departments have been incorporated in these standards."

May 1, 1944

By J. L. Konchesky

The technical feasibility of gasifying powdered, noncoking, low-rank coal with steam in an externally heated tube has been demonstrated. The tube, 112 ft. of alloy-steel tubing shaped into a helix, served as an electrical conductor of electricity used for heating. The effects of the following variables were studied: Residence time of coal in reactor, average reaction temperature, steam concentration, and rank or geologic age of coal. Reaction pressure was maintained in the range 19-26 p.s.i.a. High carbon conversions and large yields of synthesis gas were obtained with low-rank coal. In one test, for example, about 88 pct. of the carbon in a subbituminous C coal was gasified at 1,910* F. with a residence time of 1 sec. The gas contained 58 pct. H2, 19 COD 15 CO, and 3 CH4; the yield was 30 cu. ft. (at 32' F. and 14.7 p.s.i.) of synthesis gas (CO + H2) per pound of dry coal.

Jan 1, 1960

By J. R. Thoenen

This paper outlines briefly results of seismic measurements recorded in the vicinity of quarry blasting under practical operating conditions. The data cover field work done from January to the middle of August 1930, during which time records were made of 61 blasts in 19 quarries. Of the tests made, one was in biotite-gneiss, two in dolomite, two in a flintlike volcanic complex, three in gabbrodiorite, five in trap rock, and six in limestone. One quarry was in Alabama, two were in South Carolina, two in New York, four in Kentucky, five in Connecticut, and five in Massachusetts. Explosive charges ranged from 0.30 pound to 41,900 pounds, and the method of shooting varied from mud caps through hammer and wagon drill holes to churn drill holes and coyote tunnel shots.

Jan 1, 1937

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining, crushing and grinding methods, and costs at various clay-mining operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. Although the publication of total production costs might not be advisable in some instances, yet a knowledge of operating costs is essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to-this distinction between total and operating costs in order that no misunderstanding of the cost tabulations shall ensue. The following report deals specifically with the methods employed by the Dennison Sewer Pipe Co., Dennison, Tuscarawas County, Ohio.

Jan 1, 1936

By Richard D. Mehring

A refined ad improved self-sealing brattice for use in coal mine rescue and recovery operations for directing the flow of air has been developed and tested by Goodyear Aerospace Corporation for the U.S. Bureau of Mines. The brattice is made from a lightweight, low cost material that meets MSHA flammability requirements. The units can be erected using pins, spade or lightweight extensible poles. Tests here conducted to determine leakage rate from minimal to a maximum of 1.5" H20. The ability to handle reverse flows was demonstrated and a non-flammable foam was used as an auxiliary sealing agent.

Jan 1, 1978

Major activities of the Bureau of Mines Explosives Research Center during fiscal year 1965 (July 1, 1964, to June 30, 1965) are reviewed briefly. Part 1 summarizes significant accomplishments of the projects that were active during the report period. Part 2 presents short abstracts of the publications that appeared in the Bureau series and in other media during fiscal year 1965. Publications issued after June 30, 1965 are noted where pertinent in footnotes but are not abstracted.

Jan 1, 1966