Search Documents

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By H. C. George

This bulletin deals with prime movers, power-transmitting machinery, and the surface equipment and methods used to pump oil wells. It does not discuss geological problems nor the methods and equipment used in drilling or at flowing oil wells. Much of the presentation is by photographs and drawings which are described in the text. Underground equipment and methods for pumping oil wells will be discussed in a later publication of the Bureau of Mines.

Jan 1, 1925

By R. H. Fernald

In 1900, as far as available records show, there were only two producer-gas power installations in the United States. In June, 1915, the number probably exceeded 1,000. Of this number, some 84.5 per cent comprised small plants using anthracite, and only about 15 per cent of the total number utilized bituminous coal and lignite. In addition to these, two plants used wood, and three or four used oil. In the main, however, the larger sized units are operating on bituminous coal and lignite.

Jan 1, 1916

[RESULTS OF THE PRIMARY CONVENTIONAL PERFORMANCE AND COST MODEL OF THE UNIT OPERATIONS OF UNDERGROUND PERCUSSIVE DRILLING AND BLASTING]

Jan 1, 1977

By John C. Machisak

Employment and related injury experience of the coking industry in the United States for 1956 contained in this publication is summarized under three general sections: (A) General injury experience: Tables 1 to 9: Current and comparable statistics on operating data, number, frequency, and degree of severity of injuries and major accident agencies involved in the cause of injuries. Data are presented for the industry as a whole, for each type of oven, and for the States in which coke was produced. (B) Selected injury experience: Tables 10 to 15: Comparable injury data covering 5- and 10- year periods on the number and degree of severity of injuries and major accident causes.

Jan 1, 1958

By A. W. Deurbrouck

The Bureau of Mines analyzed 13 samples collected from three Randolph County coalbeds. The Peerless and Sewell bed samples were generally of metallurgical quality as received from the mines or could be easily upgraded. How-ever, the Lower Kittanning coa1bed samples proved to be quite inimical to upgrading to metallurgical quality.

Jan 1, 1966

By Felix duBreuil

The present sampling procedure for evaluating the rock dusting conditions in a coal mine is time consuming. This study considers means by which this procedure could be simplified. Surveys were conducted in six coal mines in Pennsylvania to determine the in¬combustible content of the deposited dust. Some 2,000 samples were analyzed and statistically evaluated. It is suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error.

Jan 1, 1972

By E. Don Dilling, W. F. Holbrook, Lloyd R. Michels, James W. Pennington, Dwight L. Harris, Wm. F. Hergert, Cyrus L. Blogett, H. A. Doerner, Ernest A. Reige

"IntroductionA process for production of magnesium by carbothermal reduction was developed at Padentheirm, Austria, by the Austro Americanische Magnesit Corporation& an independent investigation of this and other processes was started in 1937 by the Bureau of Mines at Pullman, Wash., with the cooperation of Washington State College. 10/ A preliminary study of the Radentheirm pro¬cess, as revealed by the meager information then available, demonstrated the following two major disadvantages,The use of hydrogen for shock cooling requires an enormous volume of gas - about 1,000 cubic feet for condensing each pound of metal as a pyrophoric dust which must be completely separated from this gas. Then if the gas is to be recycled for repeated use, the CO produced by the reduction reaction must be separated from the hydrogen. These separations are costly from the standpoint of equipment and operation. 11/The condensate is an impure, pyrophoric metal powder that must be purified and converted to coherent form. This is accomplished by distillation or sublimation of the metal. Distillation on a large scale involves difficulties inherent in the high boiling point (1,107° C.) and the chemical activity of the metal. To avoid these difficulties, the metal is sublimed at 600° C. and of very low pressure. This is quite easily carried out as a batch operation but is a costly procedure. A continuous sublimation process has not been accompli shed."

May 1, 1945

By John P. Powell

The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing new oil fields are factors that emphasize the importance of increasing the recovery of oil from known petroleum reserves. Water flooding is a valuable conservation measure, not only preventing premature abandonment of stripper leases but also reviving interest in many areas previously abandoned. The use of water flooding as a means for recovering additional oil from partly depleted oil-bearing formations was first tried in Oklahoma in 1931. Early water-flooding operations were confined to the area of shallow Bartlesville-sand formations in Nowata and Rogers Counties, where many of the projects were outstandingly successful. The results of these operations stimulated activities in other pools in Oklahoma, and by the end of 1949 water flooding had been tried in 25 of the 49 oil-producing counties in the State (fig. 1). Approximately 33 million barrels of oil, or 1,806 barrels per acre, had been recovered by December 31, 1949, from 18,221 productive acres included in the 162 active and abandoned projects in Oklahoma by injection of approximately 449 million barrels of water.

Jan 1, 1952

By J. M. Mutmansky, C. Lee

"Measurement of the size and elemental characteristics was performed on airborne coal mine dust samples collected by multi-stage cascade impactors as well as channel samples of the geologic materials. Size distributions were obtained using precise weighing techniques on the impactor substrates. Elemental analysis on the samples was performed by the proton-induced x-ray emission (PIXE) method, a rapid and non-destructive method of multi-element analysis.The various analyses were performed on 9 major and 21 trace elements. The results indicate the importance of intake air and shuttle car movements as sources of dust. The association of coal dust characteristics with channel samples was investigated using the coefficient of proportional similarity as a statistical measure. Results show a strong relationship between major elements and the geologic material being cut but a similar relationship between trace elements and geologic materials is not consistent.1. INTRODUCTIONThe most significant occupational disease in the coal industry is known ·as coal workers' pneumoconiosis (CW'P). While CW'P has existed for centuries, its mechanism of occurrence and association with coal dust has been well understood for only a few decades. In the 1930s, the significance of this disease led state and government officials in the USA to perform extensive epidemiological and environmental studies in the major coalfields. Study of these results plus later studies in the coal producing countries of Europe eventually led to the dust regulations that appear in the Federal Coal Mine Health and Safety Act of 1969.The impacts of the 1969 act were a productivity decline and increased production cost. Many analysts attributed this in large part to difficulties in complying with the new dust standards (Brezovic 1981). However, compliance was met in most continuous miner sections rather quickly. The remaining problem area is that of longwall mining where the procedures and layout of the minin~ system make it difficult to meet the standards."

Jan 1, 1989

The 1965 Lignite Symposium, the Louth in a series and the third sponsored by the University of North Dakota and the Bureau of Mines, was held at Bismarck, N. Dak., on April 29-30, 1963. These symposia provide a forum for those interested in the technology and utilization of solid fuels, especially lignitic coals. As part of the meeting, a 200-mile field trip was taken including; inspection of (1) the 200-megawatt, pulverized lignit-fired Leland Olds plant of Basin Electric Power Cooperative, under construction near Stanton, N. Dak.; (2) the site of the Glunharold mine of the Truax-Traer Coal Co., Division of Consolidation Coal Co., where a wheel excavator was being assembled; (3) the operating Beulah mine of Knife River Coal Mining Co., subsidiary of Montana-Dakota Utilities Co., near Beulah, N. Dak.; and (4) the 400-megawatt, hydroelectric Garrison Dam powerplant, near Garrison, N. Dak.

Jan 1, 1966

By Louis C. Brichta

"The O'Jack Mining Co.'s zinc and lead deposits in Jasper County, Missouri, have been worked intermittently since the early nineties; production from these deposits was greatest during World War I and II - 4,668 tons of zinc and lead concentrates. The deposits are in a sink-hole structure in which intense deformation has taken place and in areas of disturbance in the sheet-ground horizon.While high-grade ore was being mined, the operators sank seven churn-drill holes for the purpose of extending reserves. They then asked the Bureau of Mines to explore the deposit with the object of developing a reserve of lower-grade ore that could be mined by open-pit methods. Twenty-two holes were sunk. The methods of drilling and sampling and the logs of the holes, as of those drilled by the operators, are given later in this report.INTRODUCTION AND ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mined has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts development by each exploratory project as soon as practicable after its conclusion. Preliminary examination, conduct of exploratory work, and preparation of final reports are functions of the Mining Branch, Lowell B. Moon, chief, under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

Contract No. H0110929 was awarded by the U.S. Bureau of Mines in February, 1971, to DeTer Company, Incorporated, of Mountain Lakes, N. J. The contract provided for the modification of the contractor's Model 5000 Pressure Foam Generator to fit it for the suppression of coal dust in mines, a detailed testing program in a working coal mine, and for additional modifications and testing for the suppression of fires in coal mines. The contractual program was completed in April, 1972. The results of the dust suppression tests showed conclusively that the modified DeTer equipment effectively reduced the level of respirable dust in a working coal mine well below the present and future acceptable levels set by the Mine Health and Safety Act of 1969. The fire tests, carried out in a simulated mine entryway erected on the surface, demonstrated the ability of the DeTer equipment in suppressing fires of varying degrees of severity within an acceptably short time.

Jan 1, 1972

By Mark Sheppard

[Considerable research work has been done on secondary crushing and coarse rued fine grinding, and the literature on the general subject of crushing contains many references to the work of investigators on the laws governing end the factors entering into the economical production of fine materials. However, little information on primary crushing in available. The literature deals mainly with problems and practices in ore dressing, end in this field the engineer or investigations is concerned largely with the production of fine material rind the unlocking of minerals in the ore. Under such conditions close control of screen sizes of primary-crusher products is a secondary consideration and has received very little attention. The growth and development of tae nonmetallic industries have drawn more attention to primary crushing. Many of these industries are interested is the production of a minimum amount of fines and a maximum amount of a coarse Product that meets certain definite size specifications, a condition entirely different from that in the field of ore dressing. Under such conditions tae proper type of primary-crushing equipment and a knowledge of the factors governing the operation of such equipment nest are essential to economical production of a satisfactory material.]

Jan 1, 1938

By Robert S. Schechter

This report describes the development and application of PHASEQ/FLOW, a geochemical flow simulator capable of describing the dynamic changes in chemical composition of an aqueous solution during flow in a permeable medium. The solution components can react through intraaqueous reactions, redox, precipitation, or dissolution. The assumption of local thermodynamic equilibrium ensures maximum generality with respect to the number of species and components possible; however, the fluid flow itself is limited to one-dimension. The report describes several applications: generic batch equilibria, flowing equilibria, uranium roll-front deposition, and roll-front leaching.

Jan 1, 1985

By D. Harrington

Before the present century there existed a fairly persistent demand for the establishment of a Federal Department of Mines, but relatively little was done about it until a considerable number of very serious coal-mine disasters in 1906, 1907, 1908, and 1909 created what might almost be termed a national scandal and virtually forces the Federal. Government to take action to try to solve the problem of the cruse and prevention of such disastrous occurrences. Instead of a Department of Mines, the mining people had to accept a bureau, which was created on July l, 1910; and while the Bureau of Mines was given numerous functions, unquestionably the promotion of safety in the mineral industries was and continues to be one of its main "jobs." The Bureau's organic act was approved in 1910 and amended in 1913. Both the original and amended acts indicated that promoting; the health and safety of the mine workers constituted the chief function of the Bureau, and that this was the construction placed on its activities by those put in charge in 1910 is shown very definitely by the fact that as soon as the Bureau came into existence on July 1, 1910, both health end safety activities were started in its Mine Accidents Division. Before the end of the first fiscal year (June 30, 1911) 6 mine safety stations had been established in various parts of the United States, add 6 nine safety cars had been put into the field; by October 1910 first-aid-training work was being done in mining regions. The Bureau eras able to function so promptly in its safety work largely because sections of the Geological Survey, which had been doing some coal-mine safety work since 1907 or 1905, were transferred into the Bureau when it began to operate in July 1910. On October 30, 1911, a national First-Aid Meet was held at Pittsburgh, Pa., at which first aid and mine rescue were demonstrated. During the fiscal year 1910-11, the first year of the Bureau's existence, 509 persons were given certificates indicating completion of the Bureau's training course in first aid.

Jan 1, 1939

By Louis J. Sousa

This Bureau of Mines report examines aggregate trends in foreign direct investment in the U.S. mining and mineral processing industries between 1977 and 1984, and provides an analysis of foreign investment in several major mineral commodity industries. In 1984, 11.1 pct of total employment in the U.S. minerals industry was at firms that were U.S. affiliates of foreign firms. In 1985, the proportion of U.S. capacity held by foreign investors in nine major mineral commodity industries was as follows: steel, 5 pct; silver, 16 pct; lead, 18 pct; aluminum, 25 pct; zinc, 26 pct ; copper, 30 pet; cement, 32: pct; gold, 44 pct; and ferroalloys, 56 pct. Almost 90 pct of the total foreign investment in the U.S. minerals industry was accounted for by eight countries-Canada, the United Kingdom, France, Federal Republic of Germany, Switzerland, Japan, Australia, and the Republic of South Africa. The most fundamental reason behind the growth in foreign investment in the U.S. minerals industry has been that an increasing proportion of U.S. mineral firms and assets have been for safe, while foreign mineral companies have been the ones most willing and able to purchase these firms and/or their assets. mile the growth in foreign ownership in the minerals industry has not been without controversy, it has helped save jobs, reduce the minerals trade deficit, and- from the national defense perspective-maintain the Nation's overall mineral and metal self-sufficiency at reasonably high levels. In the absence of domestic buyers, foreign investors have helped to maintain a viable domestic minerals industry.

Jan 1, 1987

By F. B. Petermann

The Bureau of Mines conducted electric furnace smelting tests on sintered flotation concentrate and siliceous log-washed are. The flotation concentrate was derived from the Maggie Canyon deposit of the Artillery Mountains area, Mohave County, Ariz., and contained, before sintering, 35.6 percent Mil and 19.4 percent Si02 + A1203. The log-washed ore was from the McGregor deposit of the Artillery Mountains area, Mohave County, Ariz., and contained 31.2 to 33.6 percent Mil, 19.5 to 27.6 percent Si02 + A1203, and 2.5 percent Pb. This work was undertaken to determine the most effective smelting technique for producing standard products from such nonspecification ore and concentrates. The objective was to collect data, using a small furnace, which would be reasonably accurate and permit extrapolation to large-scale practice for comparing with results on specification-grade are.

Jan 1, 1962

By Ned H. Snyder

In recent years the Government and other large consumers of coal have appreciated more and more the desirability of definitely determining by chemical analysis and test the character and quality of the coal they purchase. Higher prices for coal point forcibly to the need of giving more study to engine room and boiler room efficiencies and economies; this implies an intimate knowledge of the character and quality of the fuel used. Analyses and tests of delivered coal furnish data whereby power plant results can be comprehensively studied and a continuous check maintained on the coal and on the conditions of plant operation. Under authority of acts of Congress making appropriations for technologic investigation of fuels and the analyzing and testing of fuels belonging to or for the use of the United States Government, a laboratory is maintained at the Pittsburgh station of the Bureau of Mines, where samples representing deliveries of coal purchased for Government use are analyzed and tested.

Jan 1, 1923

By Arthur L. Crawford, R. E. Head, Fred E. Thackwell, A. Lee Christensen

"The data in this report are the result of a detailed, microscopic study of composite samples of mill products collected over a 14 day period. The samples were collected and assembled under the direction of W. R. Lindsay, superintendent of the Anyox plant, and are fairly representative of the heads, middlings, tailings, and products peculiar to the scheme of concentration practiced at Anyox in 1930.The work was done in the Cooperative Microscopic Laboratory at Salt Lake City, Utah. This laboratory was equipped by the mine and mill operators of the Salt Lake Valley and functioned under a cooperative agreement between the United States Bureau of Mines the University of Utah. This is the fourth of a series of papers 6/ dealing with a microscopic study of mill products."

Oct 1, 1935