Search Documents

By E Novikov, D Johansson, U Nyberg, A Beyglou, N Petropoulos

Fragmentation is an important factor for improving downstream processes in mine operations. Six trials have been conducted at the Aitik copper mine to investigate the effect of ultra-short inter-hole delay times, i.e. smaller than 1 ms/m of burden, on fragmentation. Swelling, MWD data, and crusher efficiency were also evaluated for trials. According to the results, the effect of examined short inter-hole delay times, i.e. 0.14 to 0.86 ms/m of burden, on fragmentation was found to be marginal. Delay time of 0.43 ms/m of burden resulted in slightly finer fragmentation and larger swell; however, the effect of short delays was overshadowed by the effect of small variations in specific charge.

Jan 1, 2014

By Satish Kate

Indian limestone mines which are highly mechanized in operation and supply limestone to the cement plants have been quite successful in devising ways and means to optimize blasting parameters, so as to have best fragmentation, powder factor, and cost of excavation. In primary blasting mechanized or manually mixed ammonium nitrate Fuel Oil is quite popular in dry holes, and in case of watery holes conventional packaged slurry/emulsions are being used. In order to avail the low density characteristics of the ANFO, some limestone mines have also used Saw Dust and Rice Husk along with ANFO. A number of field trials have been undertaken to explore the suitability of mixing rice-husk and saw dust with ANFO. Presently, about 10% of rice husk/saw dust is being used only to expand the explosive column. The main technical consideration for the use of saw dust/rice husk, has been to reduce the final density and increase the occupancy of explosive in the blast-hole. This not only lowers the detonation pressure in the blast holes, but also reduces cost of explosive without compromising on the fragmentation quality. Besides, with sleeping of the charge there is no substantial fall in the blast quality.

Jan 1, 2006

By Thomas E. Brown

Commercd explosives have evolved through this century f?om dynamite through ANFO to the current lines of Water Gels and Emulsions. Water Gels and Emulsions evolved to counter the lack of water resistance and density of ANFO yet maintain its low cost position verses dynamite. Today, explosives must be safe and inexpensive and perform under a wide range of temperatures, function efficiently in wet or dry boreholes and have a good shelf life. Emulsions meet this criterion, which is why they are the current trend products worldwide.

Jan 1, 1998

By B. Papillon

There has been a veritable increase in the adoption of electronic detonators in the last few years. Electronic detonators offer several distinctive features over electric and non-el (shock tube) detonators including better timing accuracy resulting in excellent fragmentation and vibration control, certainly key mining parameters. The field programmability also helps in reducing the on-site magazine storage of detonators with diverse fixed delays. A typical electronic detonator may consist of a logic core, a communication interface, storage capacitor(s) and the ignition element. Being electronic components, the electronic detonators may be susceptible to RF or electromagnetic interference (EMI). RF sources are virtually everywhere: cellular phones/towers, radio transmission, microwaves, walkie-talkies, high voltage (HV) transmission cables and wireless networks with their characteristic frequency emissions. Safety issues prevail; e.g., whether the RF interference can cause premature or inadvertent firing whether directly or indirectly. From a reliability perspective, the RF interference may also impact on bus communications, e.g., during the logging, verifying, charging and firing phases. The deleterious communications disturbance may result in a misfire (non-firing of one or more of the detonators) which is terribly inconvenient for the mine operators and even pose a safety hazard.

Jan 1, 2009

By Robert Lee, Jeff Corace, Rob Cyr

Blasting in the heart of the historic Byward Market District of Canada’s capital, Ottawa, presents a unique set of challenges. The obvious difficulties arising on projects requiring blasting within 3 m (10 ft) of 125 year old buildings in various states of disrepair have been encountered and successfully dealt with countless times before. The complexities increase exponentially when tenuous property boundaries, unknown structural details, litigious histories and the need for encroachment agreements lead to individuals with competing interests all able to impact the same operation. Blasting on three projects in the Market was started in early 2005 after months of negotiation. Ultimately, the potential for the projects to proceed hinged on the ability to successfully disseminate blast data to the various stakeholders. As part of the agreements drawn up, property owners demanded immediate notification of the measured vibration levels with contract provisions including clauses such that any exceedance of the USBM criteria immediately triggered project shut down and complete blasting program redesign, and approval by all parties. With stakeholders located in various cities and, in some instances, on various continents, a conventional attended monitoring strategy would not satisfy the requirements. In response to the critical reporting need, Explotech Engineering Ltd. installed unattended monitoring stations around the sites, all incorporating wireless telemetry. After each blast, data was automatically transferred from the monitoring stations to a web-linked server via the wireless network, where it was immediately available to project stakeholders through a password protected website. The solution required a unique blend of data acquisition, telemetry, database, and security technologies, all married to produce a reliable system that was easy to maintain and use. While these types of systems were originally developed for use as permanent monitoring networks in operating mines and quarries, monitoring professionals are increasingly benefiting from the technology on temporary building projects that have typically been the realm of attended monitoring strategies. Globally, this has emerged as a solution to provide more timely access to data for stakeholders, and to minimize the legal exposure from multiple violations of vibration limits. As this trend is likely to continue, the regulated vibration control industry is likely to see a continued shift in technology development to leverage wireless networks and the Internet to continue to improve data transfer, archiving and distribution.

Jan 1, 2006

By Richard E. Danell

"Blasting is a principal step in the surface mining process for breaking and, in the case of overburdencasting, moving rocks and minerals. As many surface mines are coming to the end of theiroperational life, blasting can once again play an important role through the earthmoving operationsrequired to rehabilitate the minesite. Since blasting is such an energetic and destructive process, itis difficult initially to envisage its use in rehabilitation. However, blasting has found applications inmany civil engineering projects aimed at rehabilitation, including well digging, channelling and soilcompaction. For surface mine rehabilitation, the main purpose of earthmoving operations is toproduce a stable landfonn that will sustain revegetation. In particular, blasting can be applied toreducing the slope of steep walls left by quarrying and open pit mining through a modified form ofthe overburden casting technique. Blasting can also be applied to breaking up pit floors andbenches to speed and improve revegetation of these areas (subsoiling)."

Jan 1, 1994

By Steve Dillingham

Today, a typical blaster is likely to wear many hats, including, but not limited to, supervisor, risk manager, safety coordinator, explosives engineer, communicator, as well as professional decision maker. Simply put, a blaster in the new millennium is an all encompassing blast site manager. As you know, accidents on the blast site can range from blast crew injuries to blasting incidents resulting from vibration, flyrock, misfires, etc. Not surprising, the incidents can quite often be traced back to direct preventable human action on the blast site. They can, however, frequently be avoided, if responsibly identified early and managed properly by an efficient blast site manager. Your company cannot afford to simply employ blasters; good blast site managers are necessary to produce the safest results possible.

Jan 1, 2001

By Ethan Steward, Kyle Perry

To test the effects of impact on mine seals, a projectile generator and two seals have been constructed. The projectile generator is a 12-inch (30.5 cm) inner diameter steel pipe with a 4-inch (10 cm) wall, is 8.5 feet (2.6 m) in length, and sealed on one end. Projectiles are propelled by a charge of black powder with a wooden wad and are held in place by foam sabots in the bore. This system, combined with the large bore, allows firing of many different potential projectiles that may be found in an underground mine at a high velocity into the seals.

Feb 1, 2020

By Roberto Folchi

"This article deals with the excavation of a tunnel below the town of Isola LIRI, nearFrosinone, in central Italy. The tunnel was driven into a conglomerate formation, of lacustrine_fluvial origins, consisting in carbonate clasts with a sandy_silty matrix and calcitic cement. ""Drilling andblasting"" had to be adopted in place of a tunnel boring machine which had showeduneconomical performances. Good advance speed rates were achieved notwithstanding thepresence of some above structures to safeguard. The nearest structure (an old votivechapel) was less than 10 meters (33 ft.) far from the tunnel crown; the nearest residentialstructure was at about 15 m (49 ft.)."

Jan 1, 1993

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

By Stuart Brashear, Robert Brush, Ben Cook

In early 1993, the Piney River quarry owned and operated by the Blue Ridge Stone Corporation of W W? Boxley received a series of complaints from the owners of a 130 year-old historic farmhouse that had been converted into a bed and breakfast establishment. Since the distance from the quarry to the farmhouse was substantial, a unique method of seismic data acquisition was utilized to determine if perceived blast effects were caused by air blast or low amplitude, low frequency ground vibration.

Jan 1, 1996

By Harry L. Siebert

A major Arizona highway project is jeopardizing site safety and security because of the lane rental policy. One million cubic yards of rock must be fragmented to provide two additional lanes parallel to the existing roadway. Traffic is stopped during blasting operations.

Jan 1, 1997

By Kameron Ray, Ruilin Yang

This paper compares the modeling results obtained by using a single seed waveform (SS) versus multiple seed waveforms (MS) as inputs to the Multiple Seed Waveform (MSW) blast vibration model. The field data for the comparison was collected at a coal mine. The results of the comparison showed that the MSW model yields more accurate predictions and significantly higher correlation to field measurement when using MS as input. When using a single seed waveform as input, different seed waves result in different predictions of PPV. In contrast, using the multiple seed waveforms as an input, more consistent results are obtained.

Jan 1, 2013

By Richard J. Mainiero, Michael J. Sapko, Marcia L. Harris

Since 1988, there have been thirteen documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through near surface strata into structures or other enclosed spaces as a result of nearby trench blasting or surface mine blasting. From these incidents, there are thirty suspected or medically verified CO poisonings and one fatality associated with these incidents. To better understand the variables contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out a small- scale field study to identify key factors that may contribute to the migration of CO through the ground. NIOSH conducted single- hole heavily confined experimental test shots to measure the radial pressure pulse as it propagated through surrounding monitoring holes to determine if a relationship existed between the pressure pulse and resulting CO measurements afterwards. NIOSH also monitored blasts at an airport construction site. Following the detonations, the concentrations of CO, nitric oxide (NO), and nitrogen dioxide (NO2) were monitored for several days in the surrounding satellite holes. The peak CO measurements relative to distances from the shots were compared. Pressure histories and peak particle velocities (PPV) were measured at monitoring boreholes. It was found that the differential pressures recorded within the boreholes give some indication as to the likelihood of CO appearing, whereas the PPV measurements do not seem to be as good an indicator for potential CO migration. In this limited study, changes in barometric pressure had very little influence on removing the trapped detonation products, whereas applying a vacuum to the monitoring holes was effective in reducing the entrapped CO concentration.

Jan 1, 2005

By John H. Weigand, Stephen V. Crum

"VIBRONICS, INC. instrumented and monitored a residential structure for response to,blasting at aMidwestern surface coal operation. The residence was owned by the mining company and was extremely close to the operation. Blasting was conducted within 120 feet (36.5 meters) of the test structure. Up to seventeen (17), four (4)-channel seismographs were used during the monitoring period. The basement walls and floor were monitored. VIBRONICS, INC. also monitored a brick chimney in the basement and attic. Structural responses were then compared to outside vibration measurements taken in the soil near the foundation."

Jan 1, 1998

By Ajoy Singh

A study was conducted to investigate the damage potential to underground multi-seam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with higher amplitude of vibration compared to pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or high. The vibration magnitude recorded was higher in upper seams openings than in below seam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.erground Coal Mine

Jan 1, 2012

By Gregory Poole

With access to the World Wide Web, many resources are readily available for improving claim reports. With a little time spent on line, a more thorough report can be created. Claimants will accept the conclusions of a report more readily when they can view support information on their own computer, particularly when the support information is not just from blasting related web sites. Some suggested resources are discussed including aerial pictures, local tax maps, topographical maps and home repair web sites. This paper provides suggestions for tracking down support information on the web and information on how to properly reference this information. Case studies of several claim investigations are presented. These are some examples of how a little time spent online provided clear and convincing evidence to support the conclusions of the investigation.

Jan 1, 2006

By Kimberlee Falkenstein, Volha Kibitkina, Jessica Steeves

A series of experiments were conducted to obtain site specific constants for the vibration produced by a single charge and by more charges detonating in sequence, using short delay intervals. All charges were placed in relatively long boreholes in granite without a free face other than the ground surface. The boreholes were filled with water to provide good coupling with the rock and to provide identical confinement for all the blasts. Vibrations were recorded close to each blast in the vertical direction by uniaxial high frequency geophones and far field using a triaxial geophone.

Jan 1, 2013

A series of stemming confinement tests were conducted at a test site near Vernal, Utah. The purpose of the study was to determine the relative performance of various stemming enhancement “plugs”, stem types and loading configurations. The stemming performance was quantified in terms of: . Stem confinement time . Stem ejection velocity . Ground swell velocity . Ground vibration . Air blast . Crater formation Of primary interest was the performance of a new spherical stemming enhancement plug. The initial findings indicate that the hard plastic spheres improved blast performance when used appropriately. Their ability to improve blast performance is reduced when used in over confined or severely underconfined conditions. The study also evaluated the effects of air decking on stemming confinement and explosive performance.

Jan 1, 2000

By Unknown

Blast Site Security Involves: * Clearing the area * Controlling Access * Warning Signals

Jan 1, 2003