Search Documents

By P A. Gibson, J R. Brinkmann

The South African gold mining industry fires approximately 800 000 sloping blastholes daily. A programme aimed at characterizing the stope blasting process is underway in order to identify areas for improvement and to provide blasting related information for the design of mechanized sloping systems.

Jan 1, 1985

By Richard G. Burdick

The use of explosive charges for generating seismic energy has been around for a long time. For oil-field work or crustal studies, when the target of interest is many thousands of feet deep, the surface waves and similar phenomena are of little consequence. In mining applications, however, when the target is a few tens or hundreds of feet deep, the return signals are often masked by these waves and an accurate interpretation is difficult or impossible.

Jan 1, 1981

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. the contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accommodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problems with a 20-year old steel water main and clay drainage pipe 15 feet from the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By Edward J. Walter

Vibration control is affected by many factors which are difficult to isolate and evaluate. Occasionally a circumstance occurs in which one factor appears to predominate and its effects can be evaluated. Changing rock characteristic or lithologic variation is one of these factors or parameters. In a recent seismic monitoring project, lithologic variation in the form of hard lenses occurring suddenly and randomly in the rock to be excavated caused sudden and large increases in vibration level. Data are presented to illustrate these effects, and procedures used to control these effects are described.

Jan 1, 1981

By Michael A. Barbaglia, Mark William Withey

The lift shot is an essential blast design in the execution of mine creation and expansion plans. Whether it be opening a new quarry, creating a new level in an existing operation, or for control of water, lift shots are utilized to create the desired results. Lift shots by their nature differ from conventional production blasts because they have no free faces for relief of the blast. Due to this fully confined state, the primary direction of the rock movement is vertical, and the potential for excessive vibration and fly rock generation is great.

Jan 1, 1994

By G Dean Barrett

Just one year ago at the 1986 Annual Meeting of the Society of Explosives Engineers, Dr. Calvin J. Konya presented a paper entitled "Presplitting Granite Using Pyrodex, A Propellant.'' Since that time more evidence has been developed to support the concept that "...gas energy can be the principal splitting force and that the stress wave or shock wave is not necessary to cause the presplitting action to occur." Work done in Vermont and Georgia is presented, and the ability to split granite without causing radial cracking of the bore holes is demonstrated.

Jan 1, 1987

By R. K. Wharton

A European Directive requires that an explosive which is sold or transported within Europe must meet certain essential safety requirements from 1 January 2003. The assessment and certification of such an explosive is undertaken by an Explosives Notified Body and if the explosive meets the requirements a certificate is issued that allows the affixation of a CE mark. The presence of a CE mark ensures the product free access to European markets. The paper examines the requirements of the Directive, identifies those explosives that come within its scope, considers the role of an Explosives Notified Body, and explains the process of applying for certification.

Jan 1, 2002

By T. N. Singh, Vasudev Singh

Most of the surface mines in India have drilling and blasting practice as excavation method. All the mines have to keep the blast vibration level below a certain limit. But when mining operation is near some important civil structure, prediction and control of ground vibration becomes critical. Prediction of safe charge and finding the appropriate methodology is important for blasting near important civil structures.

Jan 1, 2006

By Dale S. Preece, Lee M. Taylor

Computer simulation of the physics involved in conventional rock blasting can be split into two phases; transient stress wave propagation and rock motion. Because the two phases involve totally different mechanisms and time scales, they must be numerically modeled with two different computer programs. The first phase is usually modeled with a finite element or finite difference code which treats the rock ss a continuum and simulates the transient stress wave and subsequent fragmentation of the rock. The second phase is usually modeled with a distinct element technique where the rock mass after fragmentation is no longer treated as a continuum but as a finite number of distinct particles that interact with each other through collision mechanics.

Jan 1, 1989

By Sharon K. Reamer, Klaus G. Hinzen, Brian W. Stump

"This study investigates seismic wave propagation from two production shots in a limestone quarry. Our motivation is to investigate the efficiency of two superpositioning techniques. The production shots consisted of an 18 and 20 hole explosive array detonated in a single row with constant delay times of 32 and 20 ms, respectively. A single shot was fired on a neighboring part of the quarry bench. The experiments were instrumented with 20 three component seismometers (35-120 m range). The computer-controlled electronic firing system resulted in firing time deviations of less than 1.4% of desired fired times. Linear superpositioning with the observed single shot data produces seismograms which adequately reproduce temporal effects of the multiple explosions; however, spatial effects due to the extended source length (68-76 m) are not modeled with this method. Linear superpositioning with individual half-space Green's functions for each explosion in thearray convolved with a calculated Mueller-Murphy source produces seismograms which match the time duration of the observed production shot seismograms and differ in absolute peak amplitude by less than a factor of three. Parameter estimation for the source is taken from chemical explosion study results. The single source model differs in amplitude from the observed single source seismograms by a factor of 2.3."

Jan 1, 1991

By P D. Katsabanis, L Liu

Numerical modelling of fragmentation and throw is used to provide information on practical blast design parameters. The function of airdecking and its practical implications, the importance of the initiation point and aspect ratio of cratering charges and the timing between adjacent blastholes are investigated. Accuracy requirements for detonators are discussed with emphasis placed on the volume and fragmentation of the blasted rock, and compared to experimental results. Practical guidelines which have been based on intuition are examined using the model. Some of the predictions have been tested and correlate well with experimental results, obtained in the laboratory. Findings show that a minimum airdeck length is needed to realize any benefit from the application of airdecking in production blasting while the process can enhance the shock energy provided by non-ideal explosives significantly, bottom initiation of charges is beneficial to fragmentation and the aspect ratio for cratering charges can exceed the traditionally accepted ratio of 6. Regarding timing, in the ease of cratering charges, true simultaneous initiation shows beneficial results for the volume of blasted rock; however the accuracy required for practical detonators is very high. Fragmentation improves after a certain delay time while the optimum can be achieved at a range of delays. Timing affects muckpile shape; however it appears that subtle differences in delay times do not have a significant effect.

Jan 1, 1997

It has been common practice for many years to predict and control underwater blasting effects on the basis of certain simplified theories related to the pressures generated by underwater detonations. Unfortunately, two of the most commonly applied concepts in many instances do not provide an accurate modeling of typical field conditions nor the potential for damage. One of these concepts is that the damage potential is related directly to the peak pressure generated by an underwater detonation, without regard to the time history of the pressure pulse. This belief has led to the widespread use of air bubble curtains to reduce peak pressures, without considering the effect that air curtains have on the time history of the pressure pulse. At times, this procedure can be unwise. The other concept is based on the premise that pressure pulses in solids (such as rock) will always be transmitted to nearby water bodies in agreement with the theories of the transmission of plane waves across normal (perpendicular) boundaries. In reality, such conditions are quite rare.

Jan 1, 1985

By Bengt Ljung

Manual charging of long upward drilled holes in mines is a heavy and risky job today. Mechanization of this work has been requested for some time by miners, their supervisors, industrial safety organizations and the trade unions, all of whom are interested in improving the working environment. This paper presents newly-developed charging systems intended primarily for charging in connection with sublevel caving and sloping. These systems have been field-tested during 1977 in the LKAB mines in northern Sweden. The results of these field tests and the results of laboratory work conducted to help eliminate the risks involved in charging explosives are also discussed. The equipment being tested (see fig. 1 and 2) consists of a charging vehicle with articulated steering, the PT-60, which has been equipped with a hose feed system mounted on the hydraulic extension boom. From a sheltered position, the operator brings the detonator and primer to the hole opening, after which the hose is pushed in mechanically to the end of the hole. Measuring equipment indicates when and if the end of the blasthole is reached. The operator then withdraws the hose mechanically as charging takes place.

Jan 1, 1978

By Anders Lagerkvist, Agne Rustan, Tommy Edeskar

Landfills containing house hold waste produces methane gas during its decomposition. This gas can be recovered and used for heating purposes or as fuel for vehicles. Gas drainage pipes are installed in the landfill and connected to a central suction point. Methane gas is produced over several years until the slots in the drainage pipes are clogged by black mud. And the bottom of the vertical drainage pipe are filled with mud and water. The hypothesis tested in this paper is if blasting in the drainage pipes could activate the production and flow of methane. In the first part of the paper we have studied what maximum linear charge concentration could be used in different size of PE-pipes place vertical on surface and surrounded by air. The results show that the maximum linear charge concentration for single blasts varied between 5-10 g/m, depending on the diameter of the pipe (90, 100 and 160 mm). Maximum charge concentration for the repeated blast varied between 2-5 g/m. In the second part of the paper we study what maximum linear charge concentration could be used in situ for full scale blasting tests in a special prepared test area which later on was dug out after the blastings. Up to 40 g/m could be used without damaging the top of the 160 mm diameter pipes. The increase in methane flow was so low so it could not be measured c4.5 m3/h. The conclusion therefore is that the stimulation of methane flow by explosives is not enough.

Jan 1, 2000

By Lewis L. Oriard

Ground vibrations associated with blasting are generally in a higher frequency range and of shorter duration than those generated by earthquakes, and the intensity scales for earthquakes cannot be applied directly to blasting vibrations without modification. Further, the profession does not need an intensity scale merely to estimate vibration intensity. If the blasting in question was not monitored instrumentally, it is a simple matter to estimate the range of intensities based on published prediction formulae or data from various sources such as Oriard (1), Nicholls et al (2), Hendron and Oriard (3), Siskind et al (4), and others. However, the profession has a serious need, for purposes of evaluating damage claims, to understand the relationships between vibration intensities and the levels of observed effects. The criteria for threshold damage do not apply to typical cases which usually involve structural damage. If the damage in question would have required ground vibration with a particle velocity of, say, 20-120 ips, damage is not verified by showing that the vibration merely approached a suggested limit to avoid threshold damage. That is not the question. This paper provides some guidelines for comparing severity of damage to intensity of vibration which would be required to cause such damage, much as is done when determining earthquake intensities. In addition, this paper includes a discussion of strain amplitudes induced by environmental forces, the predominant causes of damage to structures. Also, certain popular myths regarding blasting damage are discussed in the paper. Due to space limitations, the paper will not include a discussion of airblast effects.

Jan 1, 1989

By Miguel Araos

The aim of this study was to understand clearly how VOD of emulsion-based gassed explosives is influenced by parameters such as nitrate salt composition in the oxidizing phase, product density, blend composition, gassing rate, type of sensitization, etc. Also some VOD testing was performed on watergel-based gassed explosives in order to compare the results with those obtained for emulsions. VOD measurements were conducted in the surface blasting facility at the Research and Development laboratory of ENAEX SA (Calama, Chile). Despite the fact that the influences of some parameters on VOD of emulsion-based gassed explosives are easily predicted, there was found to be an unexpected correlation. Although it is commonly believed that the VOD of gassed explosives depends on the density, this study found that the VOD depends on the both size and the amount of gas bubbles incorporated into the product as well as type of sensitisation, regardless of whether the explosive was straight emulsion or a blend. Density is just a consequence of the incorporation of voids into the explosive. Future work in this area may examine variation of other parameters, in order to obtain a greater knowledge of detonation properties and therefore to design more efficient explosives.

Jan 1, 2002

By B Mohanty

Several parameters such as, Energy, Strength, Brisance, Impulse, and Bubble Energy, are in common use in the explosives industry today to rate commercial explosives in terms of blasting performance. However, this multiplicity of terms, their frequent interchange and their purported one-to-one correlation with expected performance have given rise to a considerable amount of confusion, and have often resulted in unrealistic rating of explosives. In this paper, various theoretical and experimental methods of estimating energy and performance of explosives are discussed and their relative merits examined. These methods include, Computer Code Calculations, Cylinder Test, Trauzl Test, Ballistic Mortar Test, Underwater Test and Model-scale blasting. It is shown, in the light of actual blasting process, that such measures cannot be considered accurate indicators of expected blasting performance as the properties of rock to be blasted are either totally ignored or only partially accounted for in these methods. It is also shown that no single technique alone among those currently employed by the explosives industry can lead to realistic rating of explosives in terms of expected blast results. The need for the adoption of a two-tier rating system, one based on chemical potential "energy", and the other based on blasting "performance" is proposed, and specific approaches to achieve this objective are outlined.

Jan 1, 1981

By D VanDoorselaere

"Image analysis techniques are widely used for blast fragmentation measurement, and various commercial packages are available for this purpose. These packages are very versatile and serve as a useful tool for optimization of blasting practice. But many times, the results provided by image analysis techniques do not match with sieved and predicted data. This leads to the suggestion that understanding the limitations of this technology is as important as understanding its usefulness and versatility.A study was conducted in two stages:(a) Comparison between the results of image analysis and screened data using laboratory scale muck piles.(b) Comparison between predicted (Kuz-Ram) and measured (Image analysis) blast fragmentation results for several bench blasts.During laboratory work, muck piles with known size distributions were analyzed with the help of image analysis technique. A disparity was observed between the sieved and measured results because the image analysis techniques cannot accurately determine the % of fi nes in the muck. During fi eld work about fourteen blasts were monitored. It was observed that predicted (Kuz-Ram) results rarely matched with measured (Image analysis) results. The Kuz-Ram curves were modifi ed by changing the rock factor so that the Kuz-Ram and Image analysis curves match in the vicinity of the 50% passing size. The pairs of curves (modifi ed Kuz-Ram and Image analysis) were divided into three categories depending upon their differences in the coarse and fi nes ranges. The blast design parameters affecting the difference between the pair of curves have been outlined. The suggestions have been made to better utilize the image analysis system."

Jan 1, 2007

By AN Gupta, N V. Srinivasa Rao

Initiating devices like detonators use sensitive primary explosives. Successful detonation of secondary explosive is achieved by suitable source of energy from primaries. The most widely used primaries contain toxic lead azide and lead styphnate, dinitrodiphenol or tetracine. All these primaries are very sensitive to friction, impact and heat. The handling of these chemicals is very hazardous and many accidents reported in detonator manufacturing were from these primaries only. In addition to this high sensitivity, lead azide and lead styphnate contain lead which is toxic.

Jan 1, 2014

By Alan R. Cameron, William Forsyth, Tom H. Kleinel

Because good and bad blasting must be defined in terms of overall mining costs, blast optimization requires combined blasting and costing models. Furthermore, the models must be both accurate and comprehensive. A combined fragmentation and preliminary costing model was developed to investigate alternative blasting strategies.

Jan 1, 1995