Search Documents

By D. C. Valdemeri, Oppermann J. P. Z., R. G. Schaarschmidt, C. S. Mendonca

This case study was conducted in an aggregate company, located at Estância Velha town, RS, Brazil. The study was based on the results of vibration monitoring mainly in terms of PPV (peak particle velocity) and frequency. Changes in the blasting design were performed to adjust the limits determined by the Brazilian standard NBR 9653:2005. Understanding the seismic wave attenuation for the site, changes in the blasting design were tested to fit the limits, such as reduction of maximum charge per delay, initiation orientation and sequencing and finally the replacement of accessories like "shock tube" by electronic initiation system. The results are shown below.

Jan 1, 2015

By Tapan Goswami

A column of stemming material keeps explosion gases at high pressure for longer times in a blasthole. In general, use of appropriate stemming enables the achievement of the desired level of fragmentation and looseness of muckpiles, as well as the reduction of airblast and fly rock. The ejection resistance of a stemming column varies with the type of stemming material employed. In an effort to optimise stemming at Mt Owen Mine in the Hunter Valley, Australia, a trial was conducted to assess the efficiency of two types of stemming materials. Mt Owen mine relies on through seam blasting and stemming quality is important in this challenging blasting environment. Each type of stemming was trialed in different section of a blast. The blast was designed using Orica’s SurveyPlus@, LoadPlus@ and ShotPlus@ software. Measurement was done using high speed filming of the blast and then post blast information was obtained from analysis of the film. Data analysis included determination of the ejection velocities and percentage swell. Digging rates were measured from excavator production rates. Despite the presence of rounded surfaces and finer particle sizes, River Pebble stemming material showed superior ejection resistance. It also appeared to perform as well as more angular and expensive Crushed Stone, a finished quarry product, based on excavator productivity and heave. It was recommended that future blasts at the mine be stemmed with the River Pebble stemming material.

Jan 1, 2000

By E. Contestabile, B. von Rosen

On August 5th, 1998, a tractor-trailer carrying approximately 18,000 kg of blasting explosives, struck a rock face on the side of the road near the town of Walden, Ontario. Eye-witness accounts of the incident state that there was an intense fire for approximately 30 minutes before the detonation. The detonation caused severe damage to the tractor-trailer, shifted the pavement and caused blast damage to the rock face. A rock fragment was recovered almost 2.5 km from ground zero and a 70 kg piece of an axle assembly was recovered over 1 km from the site. Windows were cracked at distances of almost 3 km.

Jan 1, 2001

By John T. Watson, Jim Bailey

Increasing public awareness is probably the single most important challenge faced by any blasting contractor today. This increased awareness usually results in an outcry for tighter regulations and restrictions on those in the blasting industry. Those affected do not often understand the dynamics of blasting and are simply fearful of the unknown. This reaction very often results in more regulations and restrictions which frequently fail to address the real problems.

Jan 1, 1990

By Robert Cefalo

Drill and Blast Engineer Abstract In 2019, the Bingham Canyon Mine, owned by Rio Tinto Kennecott Utah Copper Company, mined through the active underground that dewaters the pit. The active underground required the limitation of vibrations to avoid catastrophic damage or damage that would require work to the shotcrete and additional roof support. The surface design of the current sector next to and through portions of the active underground. The drill and blast group was required to test site law vibration parameters to ensure that vibration limitations were lower than limits set by the underground management team. Seismographs were used to validate the vibration prediction model and check performance of blast in areas of the underground. The bench conditions and limited pounds-per-delay created large obstacles for the blasting team, making it difficult for them to accurately load the pattern with the number of decks in the blast. Methods were used to improve the loading instructions and ensure that each hole achieved pound requirements based off of the distance to the underground that it was designed to protect. The project evolved from start to finish, and the process to estimate distances and loading improved to make the blast a more repeatable process for the size of the project.

By R Frank' Mammele Chiappetta, Conny Postupack

A major problem that has continued to plague the surface coal industry is blast induced damage to the coal seam. Atlas Powder Company has addressed this situation through seven years of field research in full-scale production environments. Many operations across the United States have been evaluated.

Jan 1, 1988

By A. Spathis, I. Yacob, A. Labriola, G. Smith

Wall control is a significant issue for many mines. Improvements to the design process for blasts adjacent to temporary or final walls will require better measurement tools and predictive models. Orica Explosives has developed capability in both these areas and uses them to guide better wall control blasting practices. Vibration and gas pressure were monitored behind a series of production blasts and single hole blasts at the Freeport Grasberg Operations Opencut Mine. The blasts used ANFO in both 3 11 mm and 35 1 mm blastholes in a blast design which reduced the charge weight by between 30 to 50% in the final row of the production blasts. Single hole blast data were obtained by delaying the last hole in the production blast. Vibration levels were within the range often associated with vibration induced damage: 178 to 1080 mm/s at distances between 14-75 metres from the blast.

Jan 1, 2001

By S B. Richardson, N T. Moxon, A C. Torrance

In many mining situations the energy released by an explosive is far too high and results in over fragmentation and excessive damage to the surrounding strata. Laboratory experiments have demonstrated that the shock energy of an explosive can be significantly reduced by surrounding it with an attenuating material such as a foam. The effect of this reduction in shock energy on fragmentation has been determined using model materials. A four fold reduction in the amount of minus 8mm material relative to an air decoupled charge of the same weight was obtained for a foam attenuator.

Jan 1, 1989

By Koichi Kurokawa, Takeo Ueda, Masahi Nakano, Yoji Tasaki

A lightning strike generates several 10kA and several billion volts, and earth currents generated by lightning is dangerous to some underground and all surface blasting operations. In order to evaluate the safety against lightning in conventional electric firing method and electromagnetic induction blasting system, a test is conducted by connecting a wire with an impulse generator. Frequency of impulse current used in the test is 17kHz and the waveform is a vibration type and the duration time is 250 ~usec. The results of the test show that induced current increases with the increasing of impulse current. In the case of MBS connection, when maximum primary current is 1700A, Maximum secondary current is 11.8A and the electric detonator is fired at this condition.

Jan 1, 1988

By David E. Siskind

Increased mineral consumption and environmental concern have caused much interest in potential damage and annoyance from ground vibration and airblast produced by production blasting in surface mines and quarries. Ground vibrations are traditionally blamed for "shaking the house to its foundations," but often the airblast is responsible, particularly when the distances from mine to structure are large. Simultaneous measurements of ground vibrations, structure vibrations, and indoor and outdoor noise from blasting are being used by the Bureau of Mines to determine the relative importance of the ground and airborne blast energy in shaking the structure and making windows, dishes, etc., rattle.

Jan 1, 1977

By Lindsay Wade, Peter Dare-Bryan

Benches in surface mines often contain known areas of ore and known areas of waste, which must be mined selectively. When rock is blasted it not only fragments but is also physically, and non-uniformly, moved. Risks therefore exist of ore being lost if treated as waste and of mill feed being diluted by waste. Both possibilities carry serious fmancial implications.

Jan 1, 2001

By Y Wada, Y Ogata, T Nishida

"Shaped charge is used for blast demolition of steel construction in general. It is important tocontrol movement of cutting part with shaped charge for the blast demolition of steel construction.Movement of cutting part was studied in the small scale experiment with steel bar. A numericalsimulation using the Discontinuous Deformation Analysis (DDA) was carried out. The DDAmethod was applied to the full scale blast demolition of steel construction. Results of thesenumerical simulation was compared with the blasting demolition work of steel tower."

Jan 1, 1999

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By Claude R. Ayoub, Charles A. Kliche, David G. McDowall

Homestake Mining Company's Open Cut Mine is located in Lead, South Dakota, in the northern Black Hills. The mine is within 300 feet of occupied residences on the south end, and within 1200 feet on the north end. Mining began at the north end of the open pit in October, 1983, and blasting related complaints began almost immediately. Noise and ground movement comprised the majority of the structural damage claims. As a result of these complaints, Homestake purchased a recording seismograph and began monitoring nearly every blast. In addition, the company hired a consultant to review Homestake's blasting and monitoring practices. He was also asked to do a single, one-time study of the cracks in six homes. This initial work led to Homestake monitoring all blasts with three seismographs and having South Dakota School of Mines and Technology do a year-long study of crack development and propagation in five homes in Lead.

Jan 1, 1989

By LaRay Collyer

San Juan Mine began pre-splitting the highwall prior to cast blasting in August 1986. The first pre-split shot used six inch PVC (polyvinylcloride) pipe inside a 10 5/8 inch hole, drilled at a 74 degree angle. The powder factor was about .90 pounds per cubic yard.

Jan 1, 1990

By Rob Farnfield

The control of vibration from surface mine blasting by the application of detonator (cap) delay techniques has been universally accepted for many years. For almost as long it has been known that, for delay techniques to be effective, a minimum of 8 milliseconds delay must exist between blast holes.

Jan 1, 1999

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

Jan 1, 2005

By Calvin J. Konya

Backbreak behind the last row of boreholes can be a significant problem for blasting operations. Backbreak will interfere with the proper drilling and execution of the subsequent shot and can produce well defined boulders, which will not be broken by the subsequent shot. In order to determine the effect of timing on backbreak, a full scale blast with 6 1/2 inch boreholes was used to test the effects of timing. The test site was a quarry which had suffered from severe backbreak regardless of the blasting pattern or explosive used. One half of the production blast was loaded and initiated using the current technology at the quarry, the other half of the blast was deliberately timed in such a manner as to minimize backbreak. The timing was such to allow for ground movement in one row before the subsequent row fired. The test results proved that the amount of backbreak and flyrock could definitely be controlled with the selection of the proper borehole timing.

Jan 1, 1987

By Robert B. Hopler

Explosives have been important to the oil and gas industries since the very earliest days. The first wells of Pennsylvania and New York in the 1860’s were able to be brought back to productivity by the use of nitroglycerin after their porosity was lowered by the high para& content of their oil. Success in the use of seismic waves to locate enemy artillery in the First World War led to the use of explosives in the 1920’s for generating ground vibrations to locate geological structures favorable for the entrapment of oil. Explosives also find widespread use in the more conventional applications of well site preparation and pipeline construction. Explosives applications unique to the oil and gas industries include the jet perforating of casings and formations, fighting well fires, and cutting casing during well shut-in.

Jan 1, 1998

By Steve Linehan, John Toedter, Kelly Williams, Mark Herman, Laura Connor, Catherine E. Johnson

Minimum safe distance (MSD) calculations are used widely in military applications to determine safe standoff distances for breaching personnel. Accurate safe distances and an understanding of blast wave propagation are critical to preventing traumatic brain injury. These calculations are often based on spherical charges in open air. However, applications including explosive breaching use planar charges rather than spherical. Previous studies analyzed the shock propagation of a square planar charge of sheet explosive and concluded the anisotropic pattern conflicted with the Kingery Bulmash (KB) and MSD spherical models. It has been determined that these predictions do not adequately predict the realistic pressures in all directions and the trend has shown to be consistent across multiple charge geometries. In this series of experiments, pressures were collected from reference spheres and rectangular geometries of detonating cord and sheet explosive commonly used in breaching and improvised demolition for this comparison. This common configuration showed pressure differences at varying angles to the charge with the highest pressures measured at the 90° position perpendicular to the “door” to be breached. Lower pressures were found at the 0° and 15° positions where the breachers would normally be standing. The reflected shock from a surface such as a door was incorporated in a semi-confined situation and added to the shock observed by the breachers. Urban environments include many surrounding structures for these reflections to occur and further testing is necessary in such an environment to determine the full-scale impact. These findings may be useful to develop improved MSD calculations for breaching applications based on charge geometry, orientation to the blast, and nearby structures.

Feb 6, 2023