Search Documents

By James W. Weaver

The 2,120-foot long cable stayed Penobscot Narrows Bridge that carries US Route 1 over the Penobscot River between Verona Island and Prospect, Maine is supported on four foundation units, one below each pylon and one at each abutment. Due to varying subsurface conditions along the bridge alignment, the structure was designed to be supported on foundations consisting of high-capacity steel H-section piles (Verona Pylon), a mat bearing on a prepared bedrock surface (Prospect Pylon) and spread footings bearing on compacted rockfill (abutments). The 70-foot by 80-foot (plan area) Verona Pylon foundation was designed to be supported by 288, 430-kip design capacity steel H-section piles (HP14x117, 50 ksi steel) driven through up to 100 feet of dense glacial till deposits containing cobbles and boulders up to 3 feet in diameter. The piles were installed using a single-acting diesel hammer (Delmag D62-22) with a maximum rated energy of 165 kip-ft. Thirteen representative piles were selected for dynamic testing (ASTM D-4945) to verify pile capacity, hammer efficiency and pile stresses. Dynamic testing determined that four different pile driving criteria were needed across the site due to variation in the bedrock and soil resistance below the footing plan area. Approximately 4 percent of the production piles were damaged/rejected due to misalignment and/or damage as a result of encountering the cobbles and boulders embedded in the glacial till. The rejected piles were located randomly throughout the plan limits of the foundation mat. Subsequent structural analyses indicated that the foundation was capable of safely supporting the design loads without the need for installing replacement piles. Evaluation of dynamic testing results with signal matching and pile driving records provided valuable information on pile side and tip resistance. Evaluations were made regarding predicted versus actual pile lengths, pile bearing material, distribution of skin friction and end bearing capacities.

Jan 1, 2011

By Vincent Tirolo

Two separate secant pile cofferdams were constructed as part of an extensive rehabilitation and modernization of the New York City Transit's Lexington Avenue/Third Avenue IND Station at 53rd Street in Manhattan. Major high rise structures and outpatient hospital facilities bordered the site. The roadway is an important east-west corridor in mid-Manhattan. In order to perform the construction of new escalator and elevator shafts over 250 linear feet of secant wall was installed to the top of rock or to the existing subway roof. Much of the secant wall was constructed from below a temporary roadway decking system using a low headroom rig. The roadway decking system was supported on shallow spread footings. The secant piles were drilled using crawler mounted hydraulic rotary drill rigs. The secant wall provided a watertight, rigid cofferdam that minimized settlement and other disruptions to existing structures and utilities. During later stages of the project the secant wall also supported the roadway decking system.

Jan 1, 2003

By David Siu

Many problems were encountered with the mechanical wedge-type splices used for the 15-inch square precast prestressed concrete piles installed at an industrial plant site. Many of the wedges were breaking during installation of the splices and after pile driving resumed following splicing. Dynamic monitoring of the piles and uplift loading tests confirmed that the problems were associated with cracked or damaged wedges. More ductile, annealed wedges were subsequently used, and, while not completely satisfactory, they were found to perform better than the original more brittle wedges. Introduction Long precast prestressed concrete piles were installed to support heavy, settlement-sensitive structures at an industrial plant in Port Alberni, British Columbia, Canada. The piles were driven through soft compressible silts and clays to toe bearing in a dense sand and gravel deposit or on bedrock. Each pile consisted of two or three segments joined with mechanical wedge-type splices trademarked DYN-A-SPLICE. Shortly after construction began, problems arose during pile installation, and these problems were, later, identified to be related to the wedges, or clamps, used to connect the splice plates.

Jan 1, 1991

By Stefan K. Schwank

The paper describes the two foundation techniques - mini piles and postgrouted bored piles. The mini pile system is presented with its design and installation parameters, especially the drilling technique. Two case histories demonstrate the application under extremely limited space and traffic conditions and the required modifications of the equipment. After the description of the postgrouted bored piles and its grouting technique, the paper gives a comparison of postgrouted piles and standard piles on a large basic test in Germany. The Brooklyn Queen's Expressway, N.Y., case history shows the application of this technique after redesign of the original proposal. 1. General Increasing requirements to improve existing foundations to carry additional loads and to increase the bearing capacity of bored piles leads to two new piling techniques: the mini-pile and the post grouted bored pile.

Jan 1, 1991

By Francis J. Arland

The installation of augered cast-in-place (ACIP) piles requires careful quality control to assure a successful pile installation. Unlike steel, pre-stressed concrete or other types of driven piles, which are shop fabricated, delivered to the site and typically driven to a minimum tip resistance, augered cast-in-place piles are installed to a pre-determined tip elevation or to a refusal criteria. The structural section of the ACIP pile is constructed during pile installation and cannot be inspected prior to installation. Therefore, a carefully administered quality control program is essential to a pile foundation that will meet or exceed design requirements. This requires an experienced team consisting of the Geotechnical Engineer, Contractor and Inspector. The focus of this paper is to discuss the responsibilities and duties of the ACIP piling Inspector. Qualifications of the Inspector The qualifications of the inspector are related to the complexity and difficulty of the proposed project. Ideally, the Inspector should be an individual with a degree in civil engineering with special emphasis in geotechnical engineering. A properly trained technician with geotechnical engineering experience working under the direct supervision of a geotechnical engineer may be able to provide competent inspection on some projects. It is important that the Inspector have a good understanding of subsurface and ground water conditions and how they will affect pile installation. The Inspector must understand ACIP pile installation procedures and be able to communicate with the Contractor, Structural and Geotechnical Engineers; and maintain a detailed pile record for each installed pile.

Jan 1, 1997

By Lok M. Sharma, Deep K. Khatri, Bradfield. Brett

"A shored enclosure was required to access a control structure upstream below the dam of a deep lake. The shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures. However, traditional analysis does not take into account soil-structure interaction. Numerical modelling offers better means to analyze soil-structure interaction. This paper presents a 2D finite element (2D-FE) analysis of a deep excavation support structure that was required to remove and replace a control structure at the upstream toe of a dam. The sheet-piling shoring was designed to withstand the lateral pressures from 14 m deep free water and 5.5 m deep excavation below the free water to reach the required excavation level to replace the gate structure. Elastic-plastic analyses were performed to predict the stresses and deformations of the complicated shoring structure and excavation bottom. The soil parameters, procedures used to develop the 2D-FE model, and the results are discussed in this paper. The shoring system is currently under construction.INTRODUCTIONA deep shoring system enclosure is required to keep out water and soil and to provide a support for unbalanced loadings due to dewatering and/or, excavation in order to permit construction of the permanent structures in the dry. A braced shoring system consists of a single wall sheet piling which is driven into the ground to form a “box” around the excavation site and is braced on the inside. After bracing the sheet piling, seal concrete is placed into the bottom to prevent water from seeping into the open excavation from underneath the sheet piling, and the water is pumped out to provide the dry work area. The braced shoring involves the interaction of the structure, soil, and water and the loads imposed include the hydrostatic forces of the water, soil pressures as well as dynamic forces due to currents and waves. Deep excavation support systems have traditionally been designed using classical methods that involve direct computations of earth pressures, (active, passive, or apparent pressures). There have been some uncertainties regarding the actual distribution of earth pressures due to influence of the support wall flexibility, as these traditional methods do not take into account soil-structure interaction. Numerical modelling offers better means to analyze soilstructure interaction."

Jan 1, 2017

By John C. Niedzielski

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site?s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The full-scale field test played a significant role in the design of the project?s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

By Mary C. Nodine, Michael P. Walker, Paul Eggers, Donald E. Aubrecht

The CANALSIDE commercial development in Buffalo, New York serves to revitalize the former site of the Buffalo Memorial Auditorium, adjacent to Lake Erie. The Auditorium was constructed in 1940 and founded on steel H-piles driven to limestone bedrock. After decades of professional sport and entertainment events, the “Aud,” as it was locally known, was closed in 1996. It sat vacant until it was demolished in 2009, at which time plans were made to revitalize the area with shops, restaurants, and a historic replica canal. The only portion of the Aud that was left intact was a subbasement boiler room. The subbasement was renovated in 2014 and has since been used to house water and ice making equipment for the historic replica canals, which boast recreational ice skating in the winter. The subbasement floor was about 10 feet below groundwater and the Lake Erie water level. The floor consisted of an approximately 4-foot-thick layered inverted waffle slab system, with reinforced concrete grade beams and concrete infill between the grade beams. A waterproofing membrane was located near the base of the slab. There were no major seepage issues in the subbasement, so the existing waterproofing membrane was assumed to be intact and performing adequately. A four-story building housing a children’s museum was proposed to be constructed directly above the subbasement. The loads imparted by the new building would exceed the capacity of the existing piles, so it was determined that drilling micropiles through the subbasement floor would be the most practical means of supporting the new building. Drilling through the existing slab and waterproofing system was a concern due to the challenges of controlling water during construction and the importance of maintaining the integrity of the permanent waterproofing system.

Jan 1, 2018

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

By Tianfei Liao

Extensive site investigations revealed that abandoned shallow mine workings exist under a site planned for construction of a major new facility. Since the mine voids were susceptible to collapse, they were stabilized by grouting. After completion of the mine remediation, three types of deep foundations (micro-piles, auger-cast piles, and drilled piers) were considered for this site. Micro-piles spread the load via the bond between the pile and the bedrock. Without significant length socketed in rock, the axial load of auger-cast piles and drilled piers has to be concentrated on end bearing. Although spreading the load is preferable in this environment, economic consideration dictated the choice of drilled piers for construction.

Jan 1, 2009

By Brian P. Waagner

Construction law in general and the law of deep foundations in particular continues to develop rapidly, particularly in the areas of risk allocation. Public and private owners are increasingly using contractual disclaimers to shift the risk of differing site conditions to contractors, and courts are increasingly willing to enforce these contractual devices. Perhaps also in an effort to control costs, public and private owners are turning to design-build contracting techniques. While design-build offers many advantages over traditional project delivery systems, it does not answer all of the risk-allocation questions that frequently arise. Even in design-build, problems with unanticipated subsurface conditions and defective design are not easily addressed. Finally, developments in electronic commerce present the potential to transform the construction industry.

Jan 1, 2002

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001

By Alan B. Wagner

The River Tower is a proposed 27-story condominium building in the heart of downtown Milwaukee, Wisconsin (USA). The tower will be over 100 m tall, and will have a ground area measuring 15 m by 40 m. The structure will be constructed of cast-in-place reinforced concrete. Certain transfer girders and stabilizing diagonals will be constructed of post-tensioned concrete. Vertical loads will be transmitted through an arrangement of columns, bearing walls, and elevator and stair cores. A mat foundation will be used to connect and integrate these load-carrying elements. The site's geologic profile includes 8.4 m of compressible estuarine (organic) deposits. To control settlement, the mat will be pile-supported. These deposits are underlain by moderate-strength inorganic deposits that extend to bedrock at 32 m.

Jan 1, 2002

By L. F. Albert

The paper describes solutions given to foundation problems during the reconstruction of a power plant set on fire, located adjacent to several still Working Units. After a detailed site and laboratory investigation, it was decided that it could be possible to include within the new foundations the preexisting cast in situ driven piles with enlarged base 50 cm in diameter and let them work with new 41 cm driven, cast in situ piles without enlarged base. Demolition of existing caps was carried out with expansive mortar in order to avoid any possible damage to piles, whose actual conditions were checked by several load tests. New piles were designed to support service load by shaft resistance, in order to limit total and differential settlement. When piles had to be driven adjacent to nearby structures, measurements of peak soil particles velocity were carried out while driving piles at decreasing distance from critical locations. By preboring most of the upper clay layer it was possible to reduce within safe limits for structures the induced vibrations.

Jan 1, 1989

By Roger A. Archabal, Omar A. Conte, Gustavo Langoni

This international case study focuses on the rigorous geotechnical interaction and results of a soil improvement program utilized to mitigate consolidation settlements of over 1.5 m [5.0 ft]. The extreme settlement results from very deep, nearly normally consolidated clay and the required high floor loading of a new Logistics Park near Bogota, Colombia. The general subsurface conditions consist of very soft clay extending to depths beyond the 50 m [164.0 ft] explored. A required 1.2 m [3.9 ft] thick fill combined with high floor loads resulted in an applied areal load of approximately 7 ton/m2 [1300 psf] (equivalent to about 4.5m [15.0 ft] of fill). Langan recommended performing a test section to validate the initial consolidation settlement calculations and evaluate possible optimization of the prefabricated vertical drain (PVD) spacing and length. The test section sizing was designed to accurately represent the stresses at depth of the future structures. Extreme settlements of over 1.5 m [5.0 ft] in the center and large differential settlements of over 0.6 m [2.0 ft] were measured between the center and corners of the test section over a relatively short test time. Discussion on the methodology, instrumentation, measured results and future optimization are presented. The recommended soil improvement varied from the standard approaches typically utilized in the area. PROJECT LOCATION AND DESCRIPTION The project site is immediately north-northwest of the city of Bogota in the Bogota Valley. The site is bordered with, and has historically been, farming land bordered to the south by the El Rosal-Bogotá highway. The overall site encompasses about 570,000 m2 [141.0 acres] of gross area and about 484,000 m2 [119.6 acres] of net buildable area. The warehouse complex will consist of 10 very large warehouses with footprints ranging from about 15,000 m2 [3.7 acres] to 30,000 m2 [7.4 acres]. The total building area is about 210,000 m2 [51.9 acres] with most of the remaining areas being paved principal drives, truck parking or administrative parking. The topography of the site is relatively flat and close to final grade in roadway areas. However, the warehouse floors will be raised about 1.2 m [3.9 ft] (equivalent to about 2 t/m2 [370 psf] considering engineered fill) to allow for truck docking. In addition, the design floor loads are heavy and estimated to be up to 5 t/m2 [930 psf] and equivalent to about 2.5m [8.2 ft] of fill. Geotechnical conditions at the site are very weak at depths of 50 meters [165 ft] or more, with soft compressible clays comprising the majority of the soil profile. The Bogota Valley is composed in some areas of very deep alluvial deposits. These deposits have been classified as an important challenge and limitation to the development of high/heavy structures such as the project in question for many years (Orozco, 2006). Soft clay deposits have been encountered even beyond depths of 100 meters [328 ft] in some regions of the Bogota Valley (Sanz, 1994). Extreme settlements can be expected if extensive and high permanent loads (above preconsolidation stress levels) are supported in these thick alluvial deposits.

Jan 1, 2018

By Rudolph P. Frizzi

"Abstract Pile design for building structures in the United States is typically performed by: 1) investigating and assigning engineering parameters to the respective ground bearing materials, 2) calculating ultimate pile to ground (geotechnical) capacity which is then reduced by a Safety Factor deemed appropriate by a registered Design Professional thereby arriving at an allowable pile geotechnical pile capacity, and 3) determining the required pile structural section using allowable pile section material properties. It is advantageous to use a Working Stress Design Method (WSDM) approach as one system of loads (service loads) are used in both the geotechnical and structural evaluation. There are a variety of methods used to determine the ultimate and allowable geotechnical capacity, and Building Codes often require a registered Design Professional to determine the appropriate method(s) and capacities. The International Building Code is the Code typically referenced in building design and construction in the United States. Structural design usually follows Building Code requirements and Allowable Stress Design (ASD) procedures. As design of the overlying structure typically follows a Strength Design Method (SDM) approach using factored loads, in some cases piling is first designed for pile-to-soil interaction using service loads, followed by evaluating the pile geometry for factored loads. Construction is the finalization and implementation of the designed piling. As such, project-specific technical specifications are typically developed by a registered Design Professional such that a project Owner can bid, buy, and instruct a Contractor as to the desired piling work and acceptance criteria. There are several Industry groups, including DFI, PDCA, ADSC, and ACI that provide guidance documents which the registered Design Professional can refer to in developing the piling technical specifications. It is the author’s opinion that the registered Design Professional is best suited to observe and verify the piling installation; many Building Departments require verification and documentation by a registered Professional as a condition of final acceptance.INTRODUCTIONPile design for building structures consists of: investigation, design, specification, and verification. In major metropolitan areas within the United States, Building Codes typically identify minimum requirements for each of the above steps. The International Building Code (ICC, 2012) is the Code typically referenced in building design and construction in the United States. Recognizing the ground conditions as well as piling construction means and methods can vary on a site-by-site basis, latitude is given to the registered Design Professional and Contractor to optimize the piling system for the respective project conditions. Field testing and quality control / assurance measures are typically implemented to verify the design intent is attained for the production pile elements."

Jan 1, 2014

By Andrew L. Peterson

CATOH Inc. of Weedsport, New York recently completed a very challenging Bored-In Pile project which features unique construction techniques in the installation and load testing of 45 and 100 ton capacity piles. The bored-in piles were installed on a twenty-nine million dollar New York State Department of Transportation project which began in the fall of 1995 and ended in March of 1997. The project included the construction of 5 new bridges to alleviate a very congested traffic network which had come to be known as the "Octopus" in the small city of Ithaca, New York. CATOH Inc. was awarded the piling contract by general contractor Santaro Industries in the fall of 1995. Piling installation work was completed in March of 1997. BACKGROUND The project is located at the southern tip of Cayuga Lake which lies in the heart of Upstate New York's Finger Lakes Region. This region is popular not only for wine making and vacationing, but also for its impressive geological history. The glacial activities that helped to form the deep valleys of this scenic area are also responsible for creating challenging underground conditions for deep foundations work. CATOH developed two pile designs to accommodate differing site conditions on the project. Internally reinforced piles were developed for use in the center of the valley and externally reinforced piles were developed for locations close to the valley wall.

Jan 1, 1997

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006

By Antonio Marinucci, Robin Mao

The new Hangzhou West Railway Station, which is currently in the early stages of construction, will be located in the city of Hangzhou, China. To accomplish the ambitious goals of the project, the construction work and station building was divided into three project areas. The original design utilizes 1,580 drilled shafts with diameters of either 800 mm or 1000 mm (32 or 40 inch) to support the new Station and its various ancillary structures. The drilled shafts will be tipped into the moderately weathered argillaceous siltstone a distance between 5 and 15 m (16.5 and 49 ft), resulting in an effective pile length ranging from 35 to 43 m (115 to 141 ft), respectively. For the first phase, approximately 550 production drilled shafts will be installed. Eight (8) sacrificial drilled shafts each with a diameter of 1000 mm (40 inch) were installed to a depth ranging from 50 to 57 m (164 to 187 ft), and were tested to confirm the design parameters used for the first phase, to evaluate the contractor’s installation means-and-methods, and to provide guidance whether redesign is warranted for the subsequent two phases. Bi-directional static load testing was performed using a donut-shaped Super Cell to apply unidirectional axial loads up to 13,200 kN (2,970 kip). This paper will describe the bi-directional testing and select results obtained therefrom. The axial compressive and uplift resistances determined from the testing verified that the available axial resistance of a single drilled shaft exceeded the minimum design requirements.

By Howard A. Perko, M. Mae Benvenga, Heather H. Trantham

Displacement of soil and groundwater during helical pile installation can produce excess pore water pressures (PWP) in fine-grained soils. Pore water pressure reduces effective stress in the soil immediately adjacent to the helical pile shaft and near the helical piles. Previous studies have shown generation of PWP may affect the capacity to torque ratios of the helical bearing elements. Large diameter helical piles that generate much of their torque and capacity from shaft adhesion are affected by PWP and therefore exhibit significant pile "freeze" after installation. Computer modeling is used herein to evaluate PWP immediately adjacent to helical pile shafts during installation in various soil types. The models show the degree and distance from the shaft that is influenced by PWP during installation and the amount of time required for the PWP to dissipate. Pile freeze has been measured on several project sites by re‐torque measurements. These re-torque data are compared with computer modeling and correlations between saturated hydraulic conductivity and dissipation time are presented and discussed. INTRODUCTION Helical piles are full-displacement piles, meaning installation does not produce drill spoil. Soil is displaced laterally as the pile progresses into the ground. This displacement of soil causes an increase in PWP, which reduces adhesion between the pile and the soil. For helical piles with small-diameter shafts, adhesion contributes little to the overall capacity and torque of the pile, so PWP changes are not typically considered in determining pile capacity. In modern construction, the use of larger diameter helical piles has become very common. For large-diameter helical piles, changes in PWP immediately adjacent the shaft can be quite large during installation. Increased pore water pressure and reduced adhesion can have a temporary effect on pile capacity and installation torque.

Jan 1, 2018