Search Documents

By M. A. Power

The diamondiferous Drybones Bay kimberlite pipe is the largest pipe (900 m by 400 m) discovered to date in the Northwest Territories. The pipe intrudes granodiorite of the Archean age Defeat Pluton and contains crater, reworked crater (epiclastic) and diatreme facies kimberlite. In-situ measurements of seismic p-wave velocity were recorded with in-line refraction arrays over representative areas. Refractions from fresh kimberlite were recorded over epiclastic facies kimberlite in the eastern portion of the pipe and returned an average velocity of 4300 m/s. Refractions from weathered kimberlite were recorded on all lines and returned velocities ranging from 1900 m/s to 2200 m/s. Granite surrounding the pipe returned an average velocity of 5400 m/s. The results indicate that there is a definite contrast in seismic velocities between kimberlite and country rocks at Drybones Bay and suggest that seismic refraction surveys may be an effective means of screening kimberlite targets in glaciated areas underlain by igneous or metamorphic rocks.

Jan 1, 1998

By R. O. Suzuki, S. Natsui, R. Nashimoto, T. Kumagai, T. Kikuchi, H. Takai

A newly developed computational fluid dynamics model based on a multi-phase particle simulation is presented for predicting the entrainment behavior of liquid metal into slag due to rising single bubble. By comparing results calculated using this model against experimental data, it was found that the transient behavior of bubbles and the two immiscible liquids can be accurately estimated by this method. The rupturing of the thin water film surrounding the bubble was less reliably predicted, but this 3-dimensional unsteady numerical model still nevertheless provides valuable new information for directly predicting the change in the liquid-liquid interface over time. This model predicted the Young-Laplace pressure, and the interface shape was simulated with volume conservation using this model as opposed to the conventional particle method. This simulation model can calculate both of dispersed phase and continuous phase seamlessly.

Jan 1, 2015

By L. Chunpongtong

ABSTRACT Oil sands production occurs on a massive scale, making orebody estimation a challenge. In rainy conditions, operators can have difficulty accessing ore at the mapped location. Without enough inventory as a buffer, the high-cost stockpile is depleted quickly, necessitating the removal of significant amounts of overburden and interburden to meet plant feed requirements. The inventory curve—a plot of ore inventory on a period-by-period basis—plays an important role in selecting an appropriate scheduling scenario. This paper presents a programmable method for creating an inventory definition by using a pit optimization tool.

Jan 1, 2014

By Zhou Yanwen, Fudong Wang, Shing Liu

Mixed CrB2 and MoS2 powder (Cr:Mo=1:1 atomic %), without any further process, were used as the targets to be sputtered and deposited onto stainless steel and silicon substrates by pulsed DC power supply. The structures and properties of the CrBMoS films were then analyzed by using SEM, XRD, micro-hardness tester. The SEM morphology of the films showed dense, defect free structure, and the preferred orientations of the films were CrB2 (111) and MoS2 (200) according to XRD spectra. The thicknesses of the films were measured and the relationship between the deposition rates and pulsed factors was determined. The films, with the micro-hardness as high as 19GPa and friction coefficient as low as 0.02, could be considered to be the hard solid lubricant films.

Jan 1, 2015

By Richard D. Moffett

The MineSight® Implicit Modeler arms geologists, engineers and surveyors with a better approach to 3D modeling. Use the tool to quickly retrieve a 3D wireframe from drillhole data and onscreen interpretation. Generate faster and more informed decisions to guide future work and improve reproducibility of results. Implicit Modeling is a mathematical surface fitting method that interpolates points to give a smooth and realistic fit. Control results by mixing planar, sectional and non-orthogonal polygons or polylines, as well as drillhole information to create solids or surfaces. The outcomes are particularly valuable to identify ore body trends, generate 3D contours of drillhole intercepts, or produce cut-off 3D maps. MineSight Implicit Modeler (MSIM) is fully integrated in MineSight?s robust and versatile suite of products, allowing you to interpret, interpolate and calculate while moving between applications. It connects seamlessly with the MineSight Torque SQL database, offering access to extensive filtering options. MSIM makes modeling much faster, allowing geologists more time to analyze data and test theories. The presentation will reveal how MSIM complements MineSight?s geomodeling workflow.

May 1, 2013

By D. Van Tonder

ABSTRACT The comparative economics of ion exchange and direct precipitation have been analyzed by developing indicative CAPEX/OPEX models for typical alkaline leach uranium circuits. An agitated tank ore leach application is considered, comparing resin-in-pulp and direct precipitation as recovery options. Capital and operating cost estimates are derived from rates and factors used in recent studies and projects. The analysis showed the main economic drivers to be the ore grade and resin loading. The resin loading is impacted by the prevalence of competing ions, especially chloride. At resin-in-pulp solution chloride concentrations below 3 g/L and uranium grade below 640 g/t U3O8, resin-in-pulp is more economical, whereas at chloride concentrations above 3 g/L, direct precipitation is more economical.

Jan 1, 2012

By Haruka Takeura, Tomoaki Murata, Kazunari Yoshida, Masato Adachi

"Pure magnesium is a material with high functionality, however, the cold drawing of this material is very difficult, that is why, until this day there are no optimal cold drawing conditions. Furthermore, cold drawing of pure magnesium wire shows a problem with internal defects that occurs under certain conditions. In this research, the aim is the suppression of internal defects, and final target is to create the optimal cold drawing conditions for pure magnesium wires. The first step is the investigation of the drawing limit by using 250°Cannealed wire. As a result, reduction of 10% per pass was chosen for stable wire drawing. However, in this case, it was found that internal defects occurred at total reduction of over 45% during drawing. Investigation of intermediate annealing conditions that can suppress internal defects, and influence on internal defect that the die half angle and reduction per pass. As a result, it was found that the drawing condition capable of suppressing internal defects most efficiently was 13% reduction drawing by using under 6°half angle die. Consequently, it’s possible to manufacture a cold fine drawn pure magnesium wire of 100µm, without defects in the center of the wire and hindering its mechanical properties.INTRODUCTIONMagnesium is a light and high functionality material that has high vibration absorbency, heat dissipation, electromagnetic wave-shielding and recycling efficiency (Conruy, 1989). However, proper cold wire drawing conditions haven’t been established, that is why warm or hot processing is commonly used (Oishi, Mori, &Kawabe, 2005). As a result, strength improvement of the wires is not possible, that is why the production of medical tools is disregarded. If it was possible to cold draw magnesium wires, the applications for material products would expand. Further, in wire drawing such difficult processing material, if appropriate processing conditions are not selected, defects will be generated inside the drawn wire."

Jan 1, 2017

Abstract - A method to extract certain types of error variance information from paired data is presented, which constitutes an important tool for the calibration of Gy’s formula for variance predictions in the sampling of broken ores. The research summarized here complements publications by others on geochemical precision. The model and method proposed for treating duplicate data provide a practical means of deriving separate estimates of the purely analytical and aliquot sampling variances, from a unique set of duplicate assays, and, hence, proposes a new avenue for estimating effective mineral grain size.

Jan 1, 1998

By A. J. Hargraves

"It is difficult to quantify comparatively the gassiness of a property. The most common index to gassiness, cubic feet of gas per ton of coal mined, is very arbitrary and does not take into account the geological setting nor the mining operation. The gassiness of a virgin coal in situ can be assessed, but no method is precise and the most accurate methods involve prolonged field and laboratory experiments. In general, gassiness increases with depth. Whereas 'gas' normally implies methane, other gases such as nitrogen, carbon dioxide, etc. may be present in seam gas also. The inflammability of methane is a problem, particularly the explosibility of a methane-air mixture; also oxygen dilution is involved in high gas concentrations and some gases are poisonous even in low concentrations. Cross measuring into a virgin seam is usually not as troublesome as development in the seam, where narrow openings may require strong ventilation to dilute gases exuding from the face and sides. Total extraction presents problems of gas from the working seam, or from adjacent seams, particularly at the return side, or of gas-laden air from the goaf streaming out or sometimes surging out intermittently, again on the return side. In pillar extraction or longwall retreating special roadways may be required to allow the side-to-side and end-to-end flushing of the goaf which is somewhat inherent in longwall advancing. Layering may occur, particularly where ventilation conditions are not brisk. Outbursts of gas from adjoining seams may be induced by sudden rupture of roof or floor in caving workings. Outbursts of coal and gas from the working seam may occur, mostly in development work, under special environmental circumstances. Gas problems may be reduced or eliminated by predrainage of gas ....:. rarely successful from the working seam - usually undertaken from adjoining seams prior to escape of gas released by caving. The ideal solution - general predrainage of gas to the surface from measures prior to mining - has yet to be accomplished. • In the planning of gassy mines it is possible to make an assessment of gas contained in the seams and to estimate what proportion will be released into the mine air, but emission of gas into mine workings is never steady and at present there is no better planning criterion than experience at the mine next door!"

Jan 1, 1973

By N. Manopulo, J. Maier, L. Tong, C. Becker, P. Hora

The contribution presents a new finite element approach in which the common updated Lagrangian formulation is replaced by a spatial flow formulation applying a special arbitrary Lagrangian-Eulerian for-mulation (ALE). The description separates spatially the process in a die inside zone and in a profile zone. For the description of the inside zone, where the filling process occurs, a special Euler time independent mesh is applied. By this formulation the mesh has to be generated only once, which simplifies the generation of spatially optimized meshes. For mapping of the material flow during the filling process the method uses a flow surface traction method as applied in casting simulations. A further strength of the new method is the computational efficiency which allows the modelling of extrusion process with the highest complexity with a response time of 12 hours, which is important for the industrial optimization process.

Jan 1, 2015

By Sandeep Singh Sandhu, Karanvir Singh Ghuman, Manjit Singh

"Cobalt based super alloy stellite 6 was weld cladded on AISI 304 L stainless steel using SMAW process in order to improve the wear resistance for tyre crusher blades. Microstructure characterization and micro hardness testing was performed on stellite 6 cladding. The suitable parameters viz. 80 Amp current with arc weaving technique was selected by performing bead on plate experiment were further used for depositing multipass multilayer cladding to achieve full filler chemistry at the top surface. Further GTAW process was used for re-melting the top surface of the cladding. Comparative evaluation of the claddings showed that TIG re-melting resulted in increased microhardness and wear resistance in comparison to as cladded specimens even with lesser deposition of material. It was observed that TIG re-melting improved the hardness from 603 HV0.5 kg to 712 HV0.5 kg. Micro structures of stellite 6 contained cobalt solid solution matrix along with inter dendrite chromium carbides which resulted in the increased micro hardness values. Pin on disc abrasion tests were carried out at room temperature and the worn out surfaces were characterized using SEM and EDS.INTRODUCTIONThe crusher blades are used in many industries for crushing various types of material and its wider applications in tyre rubber crushing mills, metal-powder crushers industries etc. Most of the crusher blades are damaged by the wear and impact loading conditions. It is because of metal to metal abrasion and the temperature also plays a vital role in blunting the cutting edges of these blades. The wear is the major cause which leads to loss of material and thus the productivity that can never be recovered (Kotechi et al., 1992). The wear can be reduced by coating of various super alloys which could reduce the behavior of metal degradation even in aggressive environments. Cladding of cheaper low alloyed material with expensive superalloys to enhance the performance of components at low cost has been investigated by many scholars (Deng et al., 2010, Kennametal, 2007, Lolla et al., 2014, Singhet al., 2014, J.N et al., 2003, Ramkumar et al., 2012). Many researchers have reported that cladding is an application of build-up deposits of specialized alloys to resist abrasion, high temperature corrosion and impact loadings. Cladding is used for providing required mechanical strength properties as well as inhibition of oxidation and other corrosive degradation. Coatings are used to protect the heat affected areas like tubes of fluidized bed combustor etc. (Kirchbner et al., 2008, Wang et al., 1994, Hocking et al., 1993, Ananthapadmanabhan et al., 1991, Staia et al., 2001). Coating techniques are widely used for the protection of turbine engine and boiler tubes against high temperature corrosion attack, power generation equipment, chemical process equipment, aircraft engines, pulp and paper processing equipment, bridges, rollers and concrete reinforcements, orthopedics and dental, land-based and marine turbines, ships. Coatings of stellite 6 are widely used in steam turbine blades and boiler tubes for power generation because of an excellent combination of impact, wear and other properties. It can maintain its properties even at high temperature and in harsh environments (Kobayashiet al., 1999, Alam et al., 2009, Munehru et al., 2009). The loading and unloading conditions experienced by the material may induce the surface cracks which lead to its breakage and leaving large pits in the surface (Meng et al., 1995). Many researchers have reported that the properties of cladded layers can be increased by various techniques such as controlling the current variations, dilution, heat input, laser and other re-melting processes, addition of special alloying elements, speed of weldingetc(C.M Anaet al., 2002, Kumaret al., 1999, Luo et al., 2012, et al., Madadi et al., 2011, Shin et al., 2003, Kuzucu et al., 1997, Sudha et al., 2008, Sawant et al., 2017, Houdkova et al., 2016, Ciubo"

Jan 1, 2017

By Phil Molloy

"In March, 1968, Skega Ruh her Liners were used to reline the shell of an 8' x 12' Allis Chalmers ball mill.This mill is used to regrind the cyanided pulp from 58i -200 mesh to 92% -200 mesh prior to this pulp passing to the flotation circuit, at approximately 450 tons per day.Before the use of rubber liners, the regrind ball Mill shell had been lined with single wave ni-hard liner!'. These liners had an average life of five years. Ni-hard end liners were used both prior to and during the use of rubber liners, as the life of the ni-hard end liners was about seven years, and it was thus felt that little economic benefit would be realized by lining the ball mill ends with rubber.The rubber lining used has a thickness of 57.15 millimeters and the square shaped lifter bars which are spaced at 14~ inch centres, have a 4"" x 4"" cross-sectional dimension.With the use of ni-hard liners, the consumption of 1 1/4 forged steel balls averaged 1.062 pounds per ton, Using rubber liners the consumption of l~"" forged steel balls increased to 1.368 pounds per ton. Also the level of the ball load which previously had been kept at approximately 18 inches below the mill discharge, had to be increased to approximately 8 inches below the mill discharge in order to effect the same grind.The initial gri4ding performance of the newly relined mill was also poor, until the leading edge of the rubber lifter bars, which were square shaped in cross-section had been worn to a rounded profile. These lifter bars were replaced after 4 years and 3 months of operation.The advantages of rubber liners in our opinion is as follows:"

Jan 1, 1974

By Wei Yun-Jie

Columnar jointed basalt is a fractured rock, with a lot of small spacing structural planes and poor integrity of the rock mass. On the basis of the comprehensive study of the columnar shape of Columnar joints, rugosity of the fracture surface and the chemical composition of basalt, columnar joints of Bai hetan dam area were formed as a result of the cooling and shrinkage effect of magma. Columnar joints basalt are mainly chlorite, kaolinite, epidote, tremolite chemical reactions and the content of columnar joints are mainly chlorite by slice identification and chemical analysis. Columnar joints basalt showed high uniaxial tension test, low coefficient of friction and high cohesion by indoor physical and mechanical test. Columnar joints rock mass showed high strength and large deformation by field shear test and deformation test. Columnar joints basalt can be used directly as a foundation of dam as long as we follow the rules and reduce disturbance strictly.

May 1, 2009

By I. Caraconcea, M. Cousineau, S. Gariepy

"Several base metal plants operate in low grade/high tonnage conditions which impose strict cost control on all fronts for their operations to remain profitable. This leads to decisions regarding plant design, procurement, operations and maintenance that often favor cost minimization over value optimization. This may hinder the representativeness of the metal accounting systems while this should be a priority in a low margin environment. Such poor representativeness not only creates confusion in plant scheduling but can also hide suboptimal metallurgical performance. Furthermore, this situation can run undetected for a while since one dominant feature of a poor metal accounting system is its poor self-awareness. During their practice, authors have particularly identified measurement bias and reproducibility, as well as their impact on metal recoveries as areas of concern. These issues have not been extensively reviewed in the specific context of precious metals in base metal plants. Pragmatic solutions are proposed either at the design stage for a new project or to retrofit an actual operation. These solutions should be based on a business analysis that set a value of information matching the contribution of precious metals as well as the potential to use such information to act toward increasing plant profitability. Conclusions are that trade-offs are an inherent part of the design/audit/retrofit of any metal accounting system in any plant processing either base or precious metals. However, compromises must be evaluated on economic/technical ground.INTRODUCTION Every mineral processing plant must produce metal accounting reports (Morrison, 2008) where estimated saleable metal flows and inventories are published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimization, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that state of the art metal accounting is instrumental for mining companies to reach and sustain high-quality corporate governance (Gaylard, Randolph, & Wortley, 2014). However, producing a metal accounting report involves much more than just printing it (Lachance, Leroux, & Gariépy, 2015a). The underlying metal accounting system (Figure 1) is responsible not only for the reliable production of the metal accounting reports but also for the quality of the outcome. As such, the crucial tasks of its design/audit/retrofit should neither be seen as ancillary nor be left as an afterthought."

Jan 1, 2017

"The successful commissioning and ramp up of the Albion Process™ at the GPM Gold Project relied on the successful scaling up of the process from batch and continuous pilot plant campaigns (Voigt et al., 2015). Critical information about reaction kinetics and residence time, grind size and pulp density were determined at the laboratory scale and successfully applied to the commercial scale. A limitation of small scale testwork, is that some parameters cannot be measured reliably and scaling up is a function of the physical size of the equipment which isn’t possible to test with laboratory scale equipment. Oxygen mass transfer rate is one such parameter since this is a complex interaction of many factors including slurry temperature, solution and slurry chemistry, slurry viscosity, agitator type, dimensions and power, oxygen bubble residence time, oxygen purity, tank geometry and oxygen injection technique. Oxygen generation represents an important operating cost for the Albion Process™. Pivotal to the Albion Process™ operating economically at atmospheric pressure is the capability to efficiently transfer oxygen while utilising as much oxygen injected to the process as possible. To respond to this Glencore Technology developed the HyperSpargeTM supersonic gas injector. This paper compares the HyperSparge™ against other sparging techniques to quantify the benefits of oxygen injection via a supersonic gas jet on scale up of the oxygen mass transfer system. The paper then examines plant survey data from the GPM Gold Project to demonstrate the very high oxygen utilisation that can be achieved with a correctly designed oxygen mass transfer system.INTRODUCTION One of the main challenges in chemical reactor design is the scale-up of processes from the laboratory to industrial scale. Processes which cannot be faithfully simulated with an experiment at the laboratory scale face challenges due to the physical dimensions and complexity of full scale operation. One example of this is the design of oxygen mass transfer systems in atmospheric oxidative leaching circuits such as the Albion Process™. A number of constraints associated with the use of laboratory scale equipment to design full scale circuits are involved in gas mass transfer processes in agitated slurries such as the Albion Process. Chiefly, typical laboratory and pilot size equipment lacks the required volume to provide useful design data without relying on empirical correlations: the specific agitator power input is artificially high, the bubble residence time in the vessel is artificially low, the oxygen partial pressure at the base of the vessel is artificially low and the oxygen delivery method may differ significantly to the industrial process. Further, the dynamic nature of the process introduces additional impacts on gas mass transfer, including the presence of solids, recycle streams and minor elements, plus the variances within the reality of a process plant such as disruptions or variance of feed quality."

Jan 1, 2017

By S. Koppalkar

ABSTRACT: The development and evolution of the gravity recoverable gold (GrG) test procedure at McGill university is reviewed in this paper. Since the late 1980s, the research group led by the late Professor André Robert Laplante at McGill university has undertaken fundamental studies and applied research of the Knelson concentrator to develop a sustainable method of estimating GrG. Historically, a concept of “free gold” was used, and it was de?ned as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, the practical use of amalgamation has declined. around 1994, a methodology using a 3-in Knelson concentrator to measure gravity recoverable gold was established at McGill university. as a result of more than 10 years of improvement and optimization, this technique has become a standard method of evaluating GrG for gold ores, gold plant streams and platinum group metals. By 2006, about 200 GrG tests were carried out at McGill universityon ores from all over the world. recently, a modi?ed version of the GrG test (a simpli?ed test) was developed to provide a quick and rough estimate of the GrG in a sample; this simpli?ed test has theadvantage of reduced mass, processing time and cost. to recognize and honour the contributions madeby the late Professor Laplante towards the establishment of a standard test procedure for assessing gravity recovery potential, the authors propose that the GrG test be named after Laplante.

Jan 1, 2010

By P. Carlone, A. Astarita, F. Rubino

Cold gas dynamic spray is an innovative technology allowing the deposition of thin metallic layers on a bulk or sheet substrate. Titanium on aluminum deposition is very attractive to the aeronautic industry, due to the enhanced corrosion resistance and wear properties of titanium coating as well as its improved compatibility with CFRP, preserving the reduced cost of aluminum substrate. One main drawback, however, is related to the micro-porosity of the deposed layer, negatively affecting the corrosion barrier performance. In this paper, the effect of selective laser post-treatment on pure grade 2 titanium coatings on AA2020-T3 sheets was experimentally and numerically investigated. Morphological features, microstructure and chemical composition of the treated zone were assessed by means of optical microscopy, scanning electron microscopy and energy dispersive X-ray spectrometry. Microhardness measurements were also carried out to evaluate the mechanical properties of the treated coating. A numerical model of the laser treatment, based on a finite volume scheme, was implemented and solved to simulate the process and discuss the experimental outcomes. Obtained results highlighted the key role played by heat input and dimensional features on the effectiveness of the treatment.

Jan 1, 2015

By Nobuyoshi Yabuki

Building Information Modeling is a prevailing methodology in the building industry and half (by length) of the world's shield tunnels are in Japan. Accordingly, for shield tunnels from 2005 to 2007, we developed a product model called IFC-ShieldTunnel, which is based on Industry Foundation Classes (IFC), in order to meet the future demand for such a product model. IFC-ShieldTunnel was developed by adding new elements that are specific to shield tunnels and that are not included in the original IFC. The added elements include shafts, segments (A, B, and K types), waterproofing elements, segment joint elements, and ring joint elements. Furthermore, soil layers and void elements were created. Recently, we updated the product model by re-organizing the entities and correcting errors. We deployed the updated IFCShieldTunnel model in the construction of an actual shield tunnel in Tokyo for about a year from August 2010 in order to check its feasibility. In the verification process, first, segments were modeled using Autodesk Revit Structure 2011 and property data were assigned to each segment element. Next, a mapping between the original attributes of the entities of IFC and properties of IFC-ShieldTunnel segments was developed. Using this mapping and IFC?s IfcBuildingElementProxy function, we were able to convert the IFC data from Revit Structure 2011 to IFC-ShieldTunnel automatically. Segment data were also converted from Revit Structure to Google SketchUp by IFC-ShieldTunnel. Furthermore, the construction scheduling and cost data were converted from Revit Structure to EXCEL for 4D and 5D analyses of construction. We interviewed engineers who used IFC-ShieldTunnel and received positive comments about the utilization of the product model. Overall, our test demonstrated the feasibility of IFC-ShieldTunnel. In future work, we plan to apply IFC-ShieldTunnel to more projects and test its practicality.

Aug 1, 2013

By Jeffrey S. Loen

"Abstract - The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 X thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995

By S. N. Dixon

"Maximizing the value of each tonne of processed ore is the goal for all operations. Cyanidation processing of gold-copper ores has been challenging since its first use in 1889. The current practice treats a bleed or the total flow of mill solution to recover copper as copper sulfide (by sulfidization, acidification, recycling, and thickening), or to recover the cyanide (by acidification-volatilizationneutralization). The process presented uses the adsorption of copper cyanide by carbon and the selective elution of copper from carbon to concentrate copper into a smaller stream. Copper contained in the smaller stream is precipitated as copper cyanide.RÉSUMÉ Toutes les exploitations ont pour objectif commun d’optimiser la valeur de chaque tonne de minerai traité. Depuis sa première utilisation en 1889, la méthode de traitement par cyanuration des minerais aurifère et cuprifère s’est révélée complexe. La pratique actuelle traite la saignée ou le débit total d’une solution de traitement du concentrateur pour récupérer le cuivre sous la forme de sulfure de cuivre (par sulfuration, acidification, recyclage et épaississement), ou pour récupérer le cyanure (par acidification, volatilisation et neutralisation). Le procédé présenté dans cet article utilise l’adsorption sur charbon actif de la solution de cyanure de cuivre et l’élution sélective du cuivre depuis le charbon pour concentrer le cuivre en un plus petit jet. Le cuivre contenu dans ce plus petit jet est précipité sous forme de cyanure de cuivre."

Jan 1, 2017