Search Documents

By K. Fagerlund, L. Rosenback, T. Mäkinen, Y. Anjala

This paper deals with the nickel smelter and refinery concepts Outokumpu has applied at Harjavalta and several other plants. Also other process routes and modifications developed and tested by Outokumpu during the recent years are highlighted. Outokumpu started nickel production in Harjavalta in 1959. Until 1995 the Flash Smelting - Peirce-Smith (PS) converting route was applied. High grade nickel matte from the converting step was further refined by means of leaching and electrowinning to produce cathode nickel. In 1995 the nickel production capacity was increased from 17 000 t/a to 52 000 t/a based on the Direct Outokumpu Nickel Smelting Process (DON). In the DON process PS converting is eliminated and high grade nickel matte with low Fe-content is directly produced in the flash smelting furnace (FSF). Metal values from the smelting slag are recovered in the electric furnace (EF) as iron containing Ni-matte. The DON process can be operated with either two matte concept, where high grade FSF matte and EF matte are produced, or a single matte concept, where EF matte is recycled to the smelting furnace and thus only one type of high grade matte is obtained. The additional refinery capacity at Harjavalta is based on hydrogen reduction producing.

Jan 1, 2005

By Ram Song, Yohei Harada, Shinji Kumai, Kazuho Otsuka

"Recently, vertical-type high-speed twin-roll casting (HSTRC) has been developed. The HSTRC shows extremely high cooling rates over 1,000 K/s even at the mid-thickness area. The fabricated strip has many metallurgical characteristics; super-saturation of alloying elements, fine solidified structure, and homogeneous distribution of fine constituent particles. In Al-Mn based alloys, the Mn alloying element can be supersaturated in the a-Al matrix and also form Mn-containing constituent particles during solidification. The Mn supersaturation and the distribution of primary/secondary particles in cast products affect the metallurgical behavior in the down-stream processing and can improve mechanical properties of the final products. In this study, Al-Mn based alloy strips were fabricated by HSTRC with various Mn contents. The solidified microstructure, constituent particles and its distribution, and Mn solubility were investigated in the as-cast condition. Due to the high cooling rate of HSTRC, fine constituent particles were homogeneously distributed, and coarse intermetallics were not observed. Mn solid solubility was estimated by electrical conductivity. The estimated Mn solubility was equivalent between strip surface and mid-thickness area.INTRODUCTION Al-Mn based alloys, as non-heat treatable wrought aluminum alloys, are widely used in packaging and heat exchanger for automobile industry. Besides Mn, Al-Mn based alloys often contain Fe and/or Si as alloying elements or natural impurities. During solidification, Mn can be super-saturated in the Al matrix, and also form Mn-containing constituent particles. Additionally, in the subsequent thermal-mechanical processes such as homogenization, rolling, and intermediate annealing, Mn in solid solution precipitates out of the Al matrix as secondary particles. The size, distribution, type, and the amount of dispersoids including constituent particles affect to texture evolution, recrystallization behavior, and final mechanical properties of wrought Al-Mn based alloys (Huang et al., 2016; Huang & Marthinsen, 2015; Engler et al., 1995; Muggerud et al., 2013). Therefore, controlling the initial level of Mn super-saturation and the distribution of constituent particles are important in the cast Al-Mn based alloys."

Jan 1, 2018

By E. G. Baltuch

Natural Ventilation in mining and metallurgical processing applications is key to proper operation function. There are number of ventilator designs available to a project team or design engineers, the selection of which will affect both the type of building structure required, project costs and design performance which is difficult to rectify or re-engineer once implemented. Research and applied results, such as that performed by Air-Therm Inc., demonstrates that computational fluid dynamic simulation allows for 5 dimensional observation, analysis and optimization at significantly lowered cost than previously possible. These results have been fully implemented on a number of mining and metallurgical applications and the company continues to study, optimize and innovate as new tools become available to provide the best possible engineered solutions for particular applications.

Aug 1, 2013

By B. D. Pandey, M. S. Kim, B. S. Kim

The recovery of Sn from used Pb-free solder (Sn, 3~4 % Ag, < 0.9 % Cu, < 1.2 % Pb) has been investigated by electrorefining in sulfuric acid solutions containing small amount of hydrochloric acid. This involved preparation of the anode material by melting and casting the used solder followed by refining. During electrorefining, dendritic tin was deposited on stainless steel cathode. Increasing the amount of hydrochloric acid up to 0.3 mol /L in the electrolyte enhanced the current efficiency to 92.2 % and the enrichment ratio of silver to 94.3 % in the anode slime which was otherwise 84.7% and 81.6 % in absence of HCl, respectively. The electrolyte containing hydrochloric acid has also prevented the precipitation of tin oxide in the bath. In the scale-up experiment using 1.6 kg anodes, 84.3 % current efficiency and close to 100 % Ag enrichment ratio were obtained, while the purity of electro-refined tin was over 99.9 %. The energy consumption of the winning process was found to be 0.151 kWh /kg-Sn which is competitive as compared to commercial tin electrorefining processes.

Jan 1, 2014

By R. Roufail

Mineral exploration is in a race to employ drilling technology that can perform the exploration and drilling investigation in a fast and inexpensive manner. After an extensive study of the available drilling technologies in the market, coiled tubing was chosen as a tool to be employed for mineral exploration due to its flexible mobility and ease of operation with a minimum number of personnel. Since coiled tubing technology is primarily used in the oil and gas industry, it was important to re-design the coiled tube rig to drill hard rocks in a fast and feasible manner. The main requirements were to drill the smallest feasible hole diameter and go as deep in the ground as possible, in the shortest reasonable time. The drilled rock particles, cuttings, are to be collected and analysed at the surface for their metal mineral contents. The process also needs to be repeated multiple times at different locations for mapping, without the need to change the tube on the rig due to failure or potential failure. The focus of the new designed coiled tube, for drilling and mineral exploration, is three fold. First is to increase the rate of penetration in drilling by designing a small high speed turbo motor. Second is to determine the controlling parameters of cuttings transport to effectively lift the cuttings to the surface for analysis and third is to minimize the overall weight of the rig for manoeuvring and prolong the life span of the coiled tube string. In this paper, a small downhole turbo motor, 5cm outer diameter, is designed to achieve a rotation speed of up to 10,000 rpm to fit on a small bit, coiled tube drilling assembly. The motor design utilised multiple finite volume and finite element analysis softwares for fluid flow study and fluid structural interaction analysis. The paper is also introducing the concept of a flow slurry loop that is designed to lift the cutting particles to the surface for mineralisation analysis. The controlling parameters of the cuttings transportation are the particle?s physical properties such as size, density, concentration and shape, as well as the rheological properties of the carrying fluid, drilled hole angle, as well as the fluid flow rate and flow dynamics within the annulus gap between the coiled tube and drilled hole. Such parameters are addressed via experimental work as well as numerical analysis. The paper is also presenting the selection and testing procedure of the material type for the coiled tube string. The tube needs to be light in weight for overall rig weight and its transportability. The tube is also required to drill several dozens of investigation holes before failing due to fatigue. A fatigue bending machine is designed to test the endurance limit of candidate materials for coiled tube strings and a performance index methodology is followed for material selection of the optimum material. The coiled tube rig is designed to be light in weight for transportation and relocation. It is also required to speed the drilling operation with the minimum footprint and reclaim the drilled rock particles for mineral composition analysis at the surface.

Aug 1, 2013

By S. Isaac

The networks of interdependencies between elements in building projects, referred to as the project topology, are often complex and difficult for project teams to comprehend. It is hypothesized that a graphbased model of the project topology can be based on existing data in Building Information Models (BIM), facilitating the application of graph-theoretic algorithms to analyze this topology. The objective of this study is to propose an outline for the synthesis of BIM and graph theory. This synthesis is expected to contribute to the development of new tools for representing, managing and analyzing the design of building projects.

Aug 1, 2013

By I. Yutronic

Compañía Minera Doña Inés de Collahuasi&apos;s (CMDIC) Concentrator Plant is located at 4300 meters above sea level, approximately 2000 kms north from Santiago, Chile. The concentrator has three grinding lines. Each one, Lines 1 and 2, have one SAG mill at the primary grinding stage followed by a secondary grinding and classification stage consisting of one ball mill, two hydrocyclone batteries and a sump with two pumps. Line 3 has one SAG mill (Gearless Mill Drive), followed by a secondary grinding and classification consisting two ball mills, four hydrocyclone batteries and a sump with four pumps. Average throughput for these three lines is 150 Ktons per day. Peak values of 180 ktons per day have been achieved. Since late 2008 and throughout 2009 and 2010, Operations and Automation areas developed an optimization program for the grinding process, considering the implementation of Model Predictive Controllers (MPC) for the three SAG mills, and later, extending MPC to the secondary grinding and classification stages. The implementation of a MPC solution was based on stability considerations (high variability of the SAG process, high interaction between sump level control and classification efficiency, etc), requirements for an automated and consistent operation, the need to maximize throughput under timevarying scenarios and, in the long term, optimization of grinding process considering Specific Energy Consumption, among other parameters. MPC solutions had proven control robustness and strong optimizing capabilities in terms of helping in discovering new operational points and so achieving all of the aforementioned goals. On the first stage of the program, MPC implementation considered identification of dynamical process control models based mainly on historical data, in order to know the impact of a group of Manipulated Variables over Controlled Variables. Also, the impact of measured Disturbance Variables was modeled in order to take into account the high impact and interaction of these variables over the processes. At the end of this stage, 4 controllers were successfully operating for the 3 SAG mills and the secondary grinding and classification process. In response to challenges made by the working group, the second stage of the development of control applications in the grinding process required to achieve a design and implementation of a solution capable of governing the milling process, in addition to stabilization and optimization of both processes (SAG milling and secondary grinding), to integrate from a point of view of process control and automation. Therefore, in the second stage, MPC performance was continuously monitored and optimized through advanced tuning, inclusion of more process models (with proper step tests), redefinition of specific optimization criteria and adjustment to new process needs. Finally, successful MPC implementation at Collahuasi has proved that fast development and deployment of process control solutions is possible and allows immediate process stability, higher throughput, specific energy consumption reduction, and successful product size control, among many others.

Jan 1, 2012

By Alex Luyima, Michael Moats

"In the present work, the oxidation of manganous and chloride ions on a mixed metal oxide (MMO) anode from a 40 ºC electrolyte containing 160 g/L sulfuric acid (H2SO4) with various concentrations of Mn2+ and Cl- was studied using cyclic voltammetry. These results indicated that Mn2+ concentration does not affect Cl2 evolution on a non-MnO2 coated MMO anode. However once MnO2 deposits on the MMO anode, Cl2 evolution is inhibited. The effects of manganous concentration and chloride concentration on the amount of MnO2 deposited in one hour were also evaluated. Cl- concentration did not affect the amount of MnO2 generated. Increasing Mn2+ concentration resulted in an increase in the amount of MnO2 deposited.INTRODUCTIONThe electrolytic recovery of zinc (Zn) is a well-known process and is estimated to produce approximately nine million tons of Zn per year worldwide (Recendiz, Nava, Lartundo-Rojas, Almaguer, & Gonzaleza, 2009). The Zn produced by this process is of high purity and has a wide range of applications, such as galvanizing (car body parts, pipes, metal wires, etc.), sacrificial anodes in offshore industries, casting alloys, alloying of brass, primary and secondary battery industries, etc.The electrochemical production of Zn employs aluminum cathodes and lead-silver anodes (Pb- Ag) (Recendiz et al., 2009). The Zn containing mineral (ZnS) is usually associated with other elements such as Mn, Mg, Ca, Cd, Cu, Cl, Fe, F, Co, Ni, Al, As, Sb, Si, Sn, Ge, Hg etc. (Nijjer, 2000). After processing of ZnS concentrates, the electrolyte obtained still contains residual metallic and non-metal impurities. Some of these impurities can impact the corrosion rate of Pb-Ag anodes."

Jan 1, 2016

By X. W. Yi, Z. J. Li, G. W. Ma

In this paper, the compressive strength and failure patterns of reinforced cemented paste backfill (CPB) were studied aiming to promote the stability of backfilled stopes. The concept of ductile backfill was proposed and a series of unconfined compression tests were carried out on both non-reinforced and reinforced cemented paste specimens. Portland cement (3% to 5% by weight of tailings) and five different types of ductile materials (0 to 0.5% by weight of solids) were employed in this experiment for the specimen preparation. The test results showed that inclusion of ductile materials enhanced the unconfined compressive strength (UCS), reduced the post peak stress loss and transformed the failure behaviour of specimens from classical brittleness to ductility. The strength of CPB reinforced with different proportions of polypropylene fibres was compared. The stress-strain curves illustrated that both cement and fibres contributed to the increase of UCS, but higher strain values at the peak stress were achieved by fibre reinforcement. CT sliced images acquired from X-ray computed tomography (CT-scan) demonstrated that the reinforced specimen developed irregular crevices at the edge of cross sections and gained the capacity of bearing large displacements owing to the mobilised tensile strength of fibres. It leads to the potential of avoiding unexpected falling blocks of CPB when adjacent mining occurs. This finding highlights a strategy to improve the self-supporting capacity of the fill mass with less cement usage and reduce the ore dilution rates when excavating to adjacent stopes.

Jan 1, 2015

By Joseph Sawicz

By now, the concept of remotely controlling heavy equipment in underground mines has become commonplace. Personnel safety is the biggest justifier for remote control, followed by an inherent cost saving (in certain cases) when wireless video is added to the mix. There are a handful of vendors targeting this need, and for years the mines have remained loyal to their brand. But as the number of remote-control related accidents and maintenance costs increase it forces our industry to take another look at this commonplace concept. And as the blinders are taken off, the mines are getting the revelation that not all remote control systems were created equally. This paper highlights the differences between various remote control systems, and then moves into an in-depth look at HARD-LINE?s package which drastically cuts maintenance costs, and also provides a solid investment toward full Tele-operation.

Apr 1, 2005

By B. Burger, T. Bester, S. Deonarain, L. S. Schultz

"This paper details the process followed to raise drill and equip a 6.1 metre diameter vertical service shaft at Glencore’s Mindola Deeps project in Kitwe, Copperbelt Province, Zambia. The project scope comprises a shaft collar, bulk air intake, a pre-sink to -90 metres and raise drilling the shaft from surface to a final depth of 1,892 metres underground, in four separate lifts of approximately 475 metres each. Equipping of the shaft steelwork, headframe erection and commissioning the shaft for hoisting. In addition, the scope included the development of a decline down from 5430’ level underground to the new shaft position on 6205’ level. This paper will provide some insight into the successes and challenges encountered during execution of the shaft works to date and provide some learnings for future projects of a similar nature. INTRODUCTION The Mindola Mine is situated to the west of the city of Kitwe in the Copperbelt Province of the Republic of Zambia (Figure 1). The mine is owned and operated by Mopani Copper Mines Plc (MCM), whose shareholders are Glencore AG (73.1%), First Quantum (17.9%) and ZCCM Holdings Plc (10%).Productivity at the Mindola mine has been adversely affected because of significant ventilation and ore re-handling challenges, which are caused by the dilapidated infrastructure, and design of the existing vertical and sub vertical shaft system. In the circumstances, it was apparent that it was necessary to sink a new vertical shaft that would increase the volume of fresh air down the mine, improving the underground working environment and the current hoisting restrictions, resulting in an increase in productivity and efficiency. Because there were two existing levels ideally situated and perpendicular to one another and because a third level was in close proximity to that perpendicular and because the mine required a ramp down to shaft bottom in any event, consideration was given to raise drilling the shaft as opposed to using conventional blind sinking methodologies."

Jan 1, 2019

By N. Birbilis, S. Kairy, C. R. Hutchinson, D. Jiang, D. R. Feenstra, O. Gharbi

"Recent developments in metal-based additive manufacturing (AM) technology have generated considerable interest in multiple industries, owing to flexibility in design and the ability to produce final components in their net shape. The AM of high-strength aluminium alloys has not been widely explored, due to findings of undesirable microstructures leading to short fatigue life and poor fracture toughness; restricting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date. Herein, aluminium alloy AA2024 (Al-3.6Cu-1.2Mg) was additively manufactured via selective laser melting (SLM), with the resultant microstructures and corrosion properties characterised and compared to wrought AA2024-T3. Microstructural characterisation was carried out using transmission electron microscopy (TEM), revealing SLM produced AA2024 included a population of ?-phase (Al2Cu) in preference to S-phase (Al2CuMg) typical of wrought AA2024. Additionally, the corrosion properties were investigated by potentiodynamic polarisation in a range of NaCl concentrations, whilst elemental corrosion rates were also determined (including for open circuit exposure conditions) and quantified in situ with an inductively coupled plasma mass spectrometer coupled with an electrochemical flow cell. Results revealed a significant improvement in the corrosion resistance, and elemental dissolution of AM prepared 2024 relative to wrought AA2024-T3.INTRODUCTION Aluminium alloys remain the preferred candidate materials in applications requiring a balance of low density and strength. The ability to produce net shape components from aluminium alloys has accelerated due to recent developments in metal-based additive manufacturing (AM) technology, including selective laser melting (SLM) and powder bed 3D printing. The AM of Al-alloys, including Al-Si-Mg (namely AlSi10Mg), has become widespread commercially in recent years. Alloys including AlSi10Mg offer reliable and reproducible production by AM, however such alloys (and variants thereof) are not high strength alloys. The pursuit of higher strength AM Al-alloys presents significant merit to multiple industries; however, such higher strength AM Al-alloys have not been widely studied to date. The solidification of high strength Al-alloys during conventional (casting) operations needs to be executed in a manner that avoids so-called =hot-tearing‘, which can arise as a result of the solute type and loading. A report on the solidification of a high strength Al-alloy prepared by AM, along with factors related to solidification, was recently covered by Pollock and co-workers (Martin et al., 2017). It was reported that AM of high-strength aluminium alloys (which have to date been principally based on the compositions of wrought high strength Al-alloys) may lead to undesirable microstructures that reduce fatigue life and result in poor fracture toughness; presently limiting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date."

Jan 1, 2018

By C. O. Swanson

THE purpose of this paper is to discuss the use of the dip needle in the field of mining geology. The subject matter is new only to the extent that it reflects the writer&apos; s added experience in recent years. The treatment is brief, and those interested in a more extended analysis are referred to the articles listed at the end of the paper. In the discovery and tracing of mineral deposits, the clip needle, like most other geophysical instruments, can be used in two ways. One method may be termed direct; the other, indirect. The direct method is that of finding or following certain ore-bodies by virtue of their magnetic properties. Explicitly, or by inference, it is the method which many mining men and practising geophysicists have in mind when they consider whether or not a certain property should be studied by geophysical means. In the ideal case, this method demands little or no knowledge of geological conditions. The indirect method uses the clip needle as an aid to purely geological studies in working out the structure of a mineralized area. Although not as simple as the direct method, it enjoys a much wider field of usefulness. The writer&apos;s experience in the past fifteen years, which is believed to be typical, is that the indirect method finds application four or five times as often as the direct method. The indirect method is of particular value because it furnishes information concerning the relationship between geological structure and ore occurrence. Most mining engineers will agree that structural control is an important factor in the localization of ore deposits, and therefore that the subject under consideration is of some interest in mining geology. Specifically, then, the present purpose is to outline the principles and practice of using the clip needle in working? out geological structure.

Jan 1, 1941

By Yves Prévost, Guy St-Amant, Guillaume Dion

In 2010, the foreseen increase of copper grade in feed concentrate at the Horne Smelter was a significant challenge to maintain a steady copper flow throughout the process. The Horne Smelter process includes a Noranda Reactor, a Noranda Converter, pyro refining vessels and anode furnaces. Of the many challenges involved, improving the single casting wheel performance was one of the key topics. Its reliability had to be improved to meet the new production objectives, as anode copper production was to increase from 170 000 to 225 000 tonnes/year. A multidisciplinary team was dedicated to improve the casting wheel availability. The improvement project allowed pinpointing failure modes and reviewing operational and maintenance practices. The common understanding developed by the team allowed improving small components with a high gain-to-effort ratio. The project allowed reaching operational targets without any significant investment. INTRODUCTION In operation since 1927, the Horne Smelter, located in Rouyn-Noranda, in Quebec, has undergone several technological changes since its original construction. Built to smelt the Horne mine concentrates, the smelter also accepted some local custom feeds from the first years of operation. When the Horne mines stopped production in 1976, the plant became a 100% custom smelter. With the development of the Noranda Reactor (1973) and Noranda Converter (1997), the Horne smelter increased its productivity and improved its environmental performance. Continuous improvement of the Horne process allowed maintaining a high level of flexibility in the operation of the smelter, while improving its overall capacity.

Jan 1, 2019

By B. J. McKay, K. Schneider, H. B. Nadendla

"A series of experiments were conducted to assess the impact of zinc additions on the morphology and soundness of the interface of Al-Mg compound castings. It was found that high amounts of zinc (>15wt%) are necessary to affect the morphology and microstructure of the interface. At these zinc concentration levels, the formation of the zinc-rich phases t1 and ? were observed along with the Al-Mg intermetallic phases ß and ?. The micro hardness of all phases across the interface was found to be similar, ~200 Hv. This even hardness gradient is thought to avoid mechanical failure in the interface under load. In samples containing large concentrations of zinc (>15wt%), the formation of bubble shaped voids as well as the complete transformation of the aluminium alloy was observed. While the exact mechanism causing the voids has not been identified it thought to be connected to the Kirkendall effect. INTRODUCTION Conventional single material components are increasingly failing to meet the demands, in terms of cost and performance, of the transport industry. Compound castings have been identified as a promising alternative as they possess a number of benefits (Bührig-Polaczek, Röth, Baumeister, Nowack, & Sussmann, 2006). Compound casting is described as a process in which a metallic melt is cast around a solid metal shape. Preliminary research has concluded that for the stability of such a resultant hybrid structure it is imperative that both metals form a sound connection via form closure, force closure, or material bonding. A continuous material bond between the two metals is also highly desirable as the formation of a crevice between the metals could lead to galvanic corrosion, particular in a humid environment (Lao, 2013; Rübner, Günzl, Körner, & Singer, 2011). Even though Al-Mg compound castings could offer the biggest potential in terms of weight savings to date only a limited amount of research concerning such structures exists."

Jan 1, 2018

By Graham Sim

Agenda ?The Water Challenge ?Examples from Three Case Studies ?Mine Drainage, 99% recovery ?Mine Drainage, 80% recovery ?Road Dust Control ?Technology Development ? Conclusion Global water challenges Assuring sustainable quantity Improving water quality Reducing energy consumption

May 1, 2011

By V. Gaudreault

Rio Tinto Alcan (RTA) has three smelters that use the Alcoa P155 technology: two in Canada (Grande-Baie and Laterrière, Saguenay, QC) and one in the United States (Sebree, Kentucky). The oldest RTA P155 smelter was built in the 1970s (Sebree) and had an initial current intensity of 155 kA. In the 1990s, RTA installed an amperage booster in Grande-Baie smelter to increase cell productivity. Since then, RTA has continuously pushed the limit of this technology and the target amperage that was 195 kA in 2005 has been increased to 210 kA in 2010.This article describes the successful plant-scale trials to increase current intensity from 195 kA to 210 kA, and the key performance indicator results. It demonstrates RTA&apos;s technology leadership to undertake such a development with its Brownfield smelters.

Jan 1, 2011

By C. Langer

Although the existence of precious metals, particularly those of the platinum group, in the nickel ores in the Sudbury district has been known for a good many years- almost as long as the ore deposits themselves- the Mond Nickel Company were the first to effect their recovery on a commercial scale. The precious metals values of the different Sudbury ores vary considerably, and are generally higher in the copper-rich ores. These values are so very small that a direct determination in the ores gives quite unreliable results. This is not surprising if one considers that some of the ores contain on1y one unit of total precious metals in about two million units of ore, and that this one unit will consist of seven different metals, each with a different chemical behaviour. It is only after the ores have been smelted to a Bessemer matte containing about 80 per cent combined copper and nickel that the precious metals content can be determined with some degree of certainty. From the figures thus obtained, the precious metals content of the ores can be calculated, provided the tonnage of ore used to produce one ton of matte is known. The recovery of these minute quantities of precious metals out of ?such a large amount of gangue and sulphides of iron, copper, and nickel seems at first glance a commercial and technical impossibility. Nevertheless, science has found a way to conquer all the difficulties, and quite substantial quantities of the precious metals contained in the Sudbury nickel-copper ores have been regu1arly recovered for many years by the Mond Nickel Company.

Jan 1, 1927

By James H. C. Martens

Among the many interesting problems of the pre-Cambrian of the Canadian Shield is that of the origin of certain types of gneisses which are intimately associated with the granites on the one hand and with the metamorphic rocks of known sedimentary origin on the other. The observations recorded in this paper on the structure and composition of these ancient rocks found in a small part of northern Quebec may help to lead to a clearer understanding of the way in which they were formed and also constitute a contribution to the regional geology and petrography of a district for which little detailed information is available. The area considered is located near the Ashuapmuchuan, or Chamuchuan, river about 180 miles north-northwest of the city of Quebec, and therefore well within the Canadian Shield. Although most attention was devoted to the rocks along this river from the 57th to the 70th mile above its entrance into Lake St. John, a few observations on other localities to the north and northwest of that lake will be included. The field work was done in the summer of 1924 in cooperation with L. W. MacNaughton, E. S. Roberts, and B. M. Shaub, all of Cornell University. The party ascended the Ashuapmuchuan river by canoe and spent about a month near the mouth of Stacker, or Brochet, river, the outlet of the lake of the same name, returning by way of Mikoasas river. The writer wishes to express his obligation to his associates for their co-operation in the field and for their permission to publish the results. He is especially indebted to B. M. Shaub for the photographs of rock outcrops. Professor A. C. Gill g:ive many suggestions which were helpful in the laboratory study of specimens and in the preparation of this paper.

Jan 1, 1927

By Michel Noël

This paper presents a partial compilation of adopted measures of waste rock dump closures at mine sites located in Canada and Alaska, where the climate includes cold winters. The paper also presents the selection process that was followed for some of those mine sites. Mining operations usually generate waste rock that can sometimes result in very large quantities. Additionally, the nature of the ore body and the host rock will often introduce environmental impacts. These impacts need to be managed not only during the operations but also in the long term. Mine closure plans consequently have to address the long term issues that sometimes require perpetual treatment. Closure planning often involves the evaluation of risks associated with environmental and financial liabilities. It needs to consider the science, some common definition of objectives, and there will be a need to manage resources and schedules. Closure planning is essentially an exercise in constrained decision making. A performance and risk based ranking matrix is often developed during this selection process to identify the preferred option(s). The case studies presented in this paper provides a few examples. The level of knowledge on acid rock drainage from waste rock dumps has increased considerably over the past decades. It did not necessarily increase the level of complexity of the adopted closure methods, as the selected closure methods are often kept simple. A common approach consists of stabilising the slopes of the waste rock dumps material by resloping and then covering the waste rock with a growth media to support vegetation. Such covers prevent direct contact of animals with the waste rock material, minimise erosion and reduce infiltration to various degrees. The inclusion of water treatment is obviously dependent on the water quality being released.

Nov 1, 2008