Search Documents

By J. M. Wetherill

"This paper presents the results of an investigation into the level of radon, as against the natural background, at the Vicary Creek coal mine in Alberta. The concentrations of radon and daughter products detected in the mine were considered to be insignificantly higher than the concentrations of naturally occurring radon and thus do not constitute a health hazard to the miners.INTRODUCTIONTHE HIGH INCIDENCE OF LUNG CANCER among miners exposed to radon was established some thirty years ago. The presence of this gas in mines is primarily associated with pitchblende extraction operations, al-though coal contains detectab`e quantities of U30s. A previous study bas shown that coal from southwestern Alberta (Exshaw and Banff) contains lower than average concentrations of this element (1).As part of a general investigation into the occupational health environment of coal miners in Alberta, field measurements were made to establish the level of radon and to investigate the natural background radiation in the Vicary Creek coal mine, located some 16 miles north of Coleman, Alberta, on the easternmost slopes of the Rocky Mountains."

Jan 1, 1968

By A. V. Lyamin, J. P. Wang, A. J. Li, Z. Qian

"For general stability analysis of rock slopes, rock mass strength and rock mass disturbance are definitely should be considered. In addition, the impact of earthquakes must be taken into account. In fact, the rock mass strength is very difficult to be assessed which causes the difficulty of analysing rock slope stability. Therefore, an empirical failure criterion, the Hoek-Brown failure criterion, has been proposed. It is one of the most widely accepted approaches to estimate rock mass strength. The rock mass disturbance is important and was found having significant influence on evaluating rock slope stability, especially for rock slope with poor quality rock mass. In the Hoek-Brown failure criterion, the disturbance factor can represent the level of the rock mass disturbance which would provide a reasonable basis for estimating rock mass strength.This research will not only discuss the slope factor of safety, but also consider the influence of the seismic force on rock slope stability assessment using pseudo-static method. In practice, only horizontal seismic coefficient is used. Various magnitudes of the disturbance factor and recommended blasting damage zone thickness are also taken into account. The blasting damage zone thickness considered ranges from 0.5 to 2.5 times of slope height. The research results have potential to be extended and then sets of comprehensive stability charts can be provided for the rock slope stability evaluations. They will be convenient tools for practising engineers. In this study, finite element upper bound and lower bound limit analysis methods are employed. Their applicability has been investigated in some previous studies. The differences between upper bound and lower bound solutions are less than ±10% which would provide reasonable and acceptable range for rock slope stability safety factor estimation."

Jan 1, 2015

By S. Feinstein, I. Reznik, Y. H. Hatzor, O. Shitrit, Y. O. Rosenberg, H. J. Vinegar, S. Nguyen

"We report the effects of porosity and total organic carbon (TOC) content on the mechanical behavior of organic-rich chalks, based on laboratory measurements. The organic-rich chalks are from the Senonian Ghareb and Mishash formations. This deposit is an immature oil-prone source rock, about 300 meters thick, situated at shallow depths (several hundreds of meters) in the Shefela basin in central Israel. The study is based on core data collected from the Zoharim borehole.Three main phases comprise the bulk volume of this rock: 1) carbonate mineralogical phase (predominantly calcite); 2) pores (mostly saturated with brine); and 3) solid organic phase (type IIS kerogen). The mechanical effects of porosity (23-45%) and TOC (4-19%) are evaluated based on bulk incompressibilities vs. volumetric fractions analysis. Volumetric fractions of mineralogical and organic phases were obtained by porosity, density and TOC measurements. Saturated rock bulk moduli were measured through ultrasonic velocity measurements. Saturated rock bulk moduli correlate best with the sum of kerogen and pore volume fractions, rather than each of them separately. The volumetric fractions were also used to define the range of bulk modulus of the organic-rich chalk, using the Hashin-Shtrikman upper and lower bounds. Based on Marion's Bounding Average Method (BAM), the normalized stiffness factor of the chalk averaged at w=0.197, indicating a soft pore geometry. Using the average normalized stiffness factor, the BAM predictions showed excellent match with the saturated rock bulk modulus and the sum of kerogen and pore volume fractions. Based on our findings, it is inferred that kerogen grains do not support the solid skeleton but are distributed between the minerals grains. We also propose here a straightforward approach for calculating the Hashin-Shtrikman bounds, based on TOC and porosity measurements. The mechanical effects of porosity and TOC indicated here are very important for the understanding of the influence of immature kerogen presence in highly porous chalks, as the Ghareb and Mishash formations."

Jan 1, 2015

By H. A. ?ye

The ISO TC 226 (Materials for the production of primary aluminium) has presently issued more than one hundred standards on the materials: alumina, pitch, petroleum coke, carbon anodes, carbon cathodes, ramming paste, fluorides and refractory). The object of the standardization work is to find methods that both material producers and smelters will accept. Methods that are specific for the operational conditions have been developed in addition to more traditional room temperature methods. Examples of important properties under operational conditions are: Air and C02 reactivity of anodes, Equivalent temperature for baked anodes, Sodium expansion of cathode blocks, Shrinkage and Rammability of paste, Penetration of electrolyte into refractories.

Jan 1, 2006

By R. J. Labine, D. I. Brisbin, R. Roussain, P. R. Coad

"Abstract - The Owl Creek Mine is located near the west end of the Neo-archean Abitibi greenstone belt, 17 km northeast of Timmins, Ontario, and 4 km north of the Destor Porcupine fault. Gold occurs in epigenetic quartz veins and their pyritic wallrocks in two zones within a package of east striking, steeply north dipping, volcanic and sedimentary rocks. At the West Zone, 1 729 603 t of ore with a grade of 4.83 g/t Au (268 587 troy oz.) were produced from an open pit centered on a wedgeshaped unit of Tisdale Group basalt that occurs between two overturned, south facing units of Porcupine Group graywacke and argillite. Basalt/graywacke contacts are locally marked by graphiticcarbonaceous argillite, strike-parallel faults and massive quartz veins.Deformed quartz+/-ankerite veins occur along the graphitic sedimentary/volcanic contacts and in gently to moderately dipping fractures in basalts, and, to a lesser extent, in graywackes. Veins also occur sub-parallel to steeply dipping 070° foliation. Altered host basalts are composed of iron carbonate, sericite, quartz, carbon, chlorite and disseminated pyrite. Gold occurs as inclusions in pyrite, and less commonly as free gold in fractures and along graphite-quartz grain boundaries in quartz veins. Fractures preferentially developed in more competent basalts during pre- to syn-ore deformation are interpreted to have provided the permeability required for emplacement of mineralized quartz veins. Carbonaceous basalt/graywacke contacts further enhanced gold deposition by acting as chemical traps. The interaction of hydrothermal fluids with these carbonaceous sedimentary rocks led to the characteristic local darkening of host basalts due to carbon impregnation and chlorite development."

Jan 1, 1998

By K. Bunney, R. Pleysier

The deportment of a suite of elements through representative gold ore processing unit operations in cyanidation has been investigated. Chromium and lead are not soluble in alkaline cyanide solutions. Arsenic, antimony, cobalt, molybdenum, selenium, tellurium and vanadium are soluble, but typically do not adsorb onto activated carbon to any appreciable extent. Silver, copper, cadmium, mercury, nickel and zinc to varying extents report along with the gold to the carbon eluate. Cadmium, mercury and zinc can report to the carbon regeneration kiln off-gases. Strontium is soluble and adsorbs on carbon where it remgins.

Jan 1, 2011

By E. M. Hillary, D. F. Sangster

"Abstract - As a contribution to the World Minerals Geoscience Database Project, an index-level database comprising information on 142 SEDEX Pb-Zn deposits and occurrences was constructed in Microsoft Access 95 format. Although consisting of only basic information, the compilation, with full referencing of all data, is possibly the largest non-corporate SEDEX Pb-Zn database in the world. It thus provides an opportunity to make geoscience queries of SEDEX Pb-Zn deposits on a scale not previously available. This report provides a summary of the results of a few such queries both as a contribution to a better understanding of SEDEX lead-zinc deposits and as a demonstration of what even such a simple database can offer.During the compilation process, it became apparent that SEDEX Pb-Zn deposits could be assigned to one of the following three sub-types: Type 1 (53.5% of total) in which sulfide minerals are the only exhalative components; Type 2 (33.1%) in which the exhalative components are sulfides plus chert, siderite/ankerite, and/or barite; Type 3 (13.4%) which contains any components of Types 1 and 2 plus abundant iron-oxide minerals (commonly magnetite) and/or is associated with iron oxide-rich sedimentary rocks.Highlights of systematic queries of the database reveal that:1. a majority (84%) of the world’s SEDEX Pb-Zn deposits are not underlain by a discordant footwall feeder zone or vent complex;2. 63.6% of deposits occur in Proterozoic strata followed by a second peak in the Devonian (16.8%). Of those in the Proterozoic, 83% of Type 3 deposits occur in the Gondwanaland supercontinent, whereas only 42% of Type 2 and 39% of Type 1 are located in this large paleo-landmass;3. median (Pb+Zn) grades in Types 1 and 2 fall between 9% and 10% with a majority clustering within this range. Type 3 grades, however, range from ~1% to ~20% (Pb+Zn) with a median of 5%; 4. median size of Type 3 deposits is ~33 Mt, whereas Type 1 and 2 median sizes are ~7 Mt and ~8 Mt, respectively.The report concludes with a brief discussion of how an index-level database such as this can be used in conjunction with other, similar databases to reveal interesting and instructive relationships for guiding both research and exploration."

Jan 1, 1998

By Per Hedvall, Jan-Eric Ståhl

"The main objective of this study is to introduce the new Sandvik’s production cost-model within Crushing & Screening (C&S) technology. So far, there have been different ways of determining different production costs in the industry, however, the previously published and presented methods have not been very efficient in calculating the costs per product and metric ton. Accordingly, the current study has been planned and started in collaboration with Lund University to provide an accurate and easy to implement cost estimation program to determine the costs for crushing and screening plants worldwide.The proposed model has been adapted to fit the C&S processes of different rocks/ores fractions. The result is presented as cost per ton of the end product(s).Within this paper the cost estimation results for 3 different crushing and screening plants are presented based on the information obtained from the following sources: a) documents at Sandvik SRP, b) Sandvik’s crushing & screening internal/external machines/plants data and information, c) literature studies, including the use of Sandvik’s internal/external simulation and software programs, d), visiting the crushing and screening plants ,e) interviews, information systems’ data, and, f) testing and observations by ourselves.In order to improve the level of accuracy and the validity of the attained results, simplistic Monte-Carlo simulations have been used, where needed. The achieved results, so far, have proven the reliability of the model. The calculated cost estimations have shown an accuracy over 80% when they compared with real cost data obtained from plant practices.The current cost calculation model, will offer the possibility of:•,Calculating the production costs in proposed and/or existing C&S plant.•,Making detailed cost analyses for the end product(s) in proposed and/or existing C&S plants.•,Determining the profitability of each finished product when it’s required.•,Cost optimization by potentially cutting the cost for part of C&S plant with an existing plant practice"

Jan 1, 2016

By K. Soga

DOWA has long been specialized in the treatment of complex massive sulfide ores from exploration through smelting. Its competitive advantage derived from ore dressing technology to dress and concentrate complex ore to various kinds of metals concentrates. With this technology, the company recovers as many as seventeen different nonferrous metals. Therefore, it is crucial for the environment management and recycling business both to recover valuable elements like gold, silver, copper etc. and to handle hazardous elements in safety. From this view point, the nonferrous metal industry has a potential to play an important role; that is "The Anchor of Recycling" or "The Joint of Recycling Loop". By utilizing these mining, smelting and refining technologies, know-how and facilities, DOWA became a leading waste treatment, soil remediation and metal recycling company in Japan. This knowledge is now being applied in China .

Jan 1, 2007

By Tibor Horvath

Dust abatement is possible on bulk materials, whether conveyed or stockpiled. Minimum (ppm) quantities of chemical additives can efficiently and rapidly control dust of conveyed substrates with no effect on floatation chemistry. Top coating of large surface areas can control surface dust and wind erosion. Environmental and toxicity impact must be considered in any treatment, especially on areas with percolation runoff, leachates, or limited containment. The most effective dust control is preventing release of substrate fines rather than trapping and removing air borne dust. Techniques to prevent release of fines from conveyed substrates will be discussed. Dust control dynamics are a very complex combination of solid phase physical and chemical interactions between the substrate and the fines. ?Smart Technology? products permit dust abatement of stockpiled substrates and tailing fields with no environmental impact. Using ?Smart Technology?, the dust abatement products remain active and can re-seal damaged areas. Efficient, low environmental and toxicity impact, dust control will be demonstrated through case studies where these principals have been applied.

Oct 1, 2010

By Shugang Li

Coal and coal-bed methane are valuable energy resources. If they can be extracted simultaneously and safely, the triple purposes of mine safety production, new energy resource supply and environmental protection can be fulfilled. After mining, the mining induced fissure distribution feature and methane delivery behavior in overlying strata were closely related to the relieved methane degasification. Using physical simulation and numerical simulation, it was explained that the distribution feature of mining induced fissure was the Elliptic Paraboloid Zone (EPZ) in three-dimensional space. Based on the key stratum theory, the types, parameters, characteristics and dynamic evolution behavior of the mining induced fissure EPZ were analyzed. Applying environmental fluid mechanics and the mass transfer theory, the relieved methane floating-diffusion equation of the EPZ was established, and the corresponding transport process was analyzed. Using the field practice of relieved methane degasification in Tianchi Coal Mine, it explained that the mining induced fissure EPZ was the storage and delivery area of relieved methane. The degasification effect will thus be useful if the drainage system is laid in the EPZ. Such studies can provide the theoretical basis and technical support for the safe simultaneous extraction of coal and methane.

Aug 1, 2013

Mining companies around the globe have long struggled with the need to ensure that earth moving equipment is designed to be operated and maintained under all site conditions without causing harm to people. Incident and accident data from a range of sources clearly identify mining equipment related issues as major causal factors. One Australian source, the NSW Department of Primary Industries? International Mining Fatality Database Project Report (2008) noted that ?Approximately 77% of mining accidents resulting in a fatality have? involved equipment?. The largest number of fatalities were associated with trucks; the next with LHDs. Many of the technical advances in equipment design over the past few decades have not been matched by advances in the human factors design of mining equipment, resulting in a ?design vacuum? that must be filled prior to commissioning new equipment. This ?design vacuum? is generally filled by local dealers. They retrofit equipment according to customer requirements to mitigate risks that have not been designed out by the Original Equipment Manufacturer (OEM). Mining companies have been frustrated by lost time and additional costs associated with this need to retrofit ex-factory designs. Some companies have attempted to address the problem by negotiating company or site-wide ?solutions? to equipment designs, but this has not simplified or clarified the issue from the point of view of the equipment manufacturers. A number of mining companies operating in Australia first discussed the concept of a joint customer approach to improve the Human Factors design of earth moving equipment at the factory level in 2004. They agreed that a new approach to engaging with OEMs was needed; one that would define the ?Problem?, in other words, the basis of the risks, rather than dictate the ?Solution?. The Earth Moving Equipment Safety Round Table (EMESRT) was formally established in 2006 by six global mining companies to establish a process of engagement between Original Equipment Manufacturers (OEMs) and mining customers.

May 1, 2009

By Kyle Paulsen

The Cameco Key Lake mill began processing U-bearing waste rock from the McArthur River mine in 2000. This ore often contains elevated levels of calcium (>4% by mass), resulting in less than favourable conditions in parts of the Key Lake mill, yet still contains U3O8 at a concentration of about 0.3%. To recover the U3O8 and reject as much calcium as possible, modifications were made to the grinding circuit in late 2007 to include a gravity concentrator. The concentrator allows this mineralized waste to be processed separate from the regular blend material, rejecting calcium and concentrating U3O8, thus improving the operating conditions in areas such as SX. This will be presented in greater detail along with results and further work.

Aug 1, 2010

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By S. Xu

Magnesium alloy AM50 is of interest to automotive cradle application because of it excellent castability and good ductility. In this work, microstructure and mechanical properties of both low pressure die cast (LPDC) and high pressure die cast (HPDC) AM50 test bars are characterized. Microstructure was examined using optical microscope, scanning electron microscope (SEM) and transmission electron microscope (TEM). Phase identifications were performed using energy dispersive x-ray spectrometer (EDS) and TEM diffraction. It has been found that LPDC produces much coarser microstructure than HPDC. At the same time, the HPDC samples are more heterogeneous in microstructure and composition close to grain boundaries. Particles with various dimensions and morphologies of two different intermetallic phases, Mg17A112 and A18Mn5, were found in all the samples. Mechanical tests were performed under conditions similar to those related to an engine cradle application. LPDC samples show lower strength but better creep resistance than HPDC mainly due to the difference in grain sizes and grain boundary microstructure between LPDC and HPDC. Creep curves are well described by the empirical Andrade equation. Tensile-compressive yield and creep asymmetries were found in AM50, i.e. better deformation resistance in tension than in compression. The average yield asymmetry ratio for all the samples is 0.87. Microstructural examinations on the samples tested in tension, compression and creep showed that the deformation mechanisms in AM50 were slip plus twining at temperatures up to 125°C. The examinations indicate the important role of twining in the asymmetry phenomenon. The creep results indicate that dynamic precipitation of the Mg17A112 phase during testing is not the mechanism directly responsible for the creep asymmetry in AM50.

Jan 1, 2004

By Guoxiang Chi

This paper consists of two parts: the first part describes the principles and functionality of the BsnMod program, and the second part presents preliminary application of this program to paleo-fluid flow modeling in the Anticosti Basin. The BsnMod program simulates fluid flow and heat transfer during the evolution of sedimentary basins through numerical solution (finite difference method) of three partial differential equations, which describe sediment compaction, fluid continuity, and heat conservation. It can be used to estimate the evolution of fluid overpressure, flow rate, and temperature during the basin history. The program was written in C++, works under Windows environments, and has a user interface allowing inputs in dialogues and outputs in both tabular and graphic forms. The program was applied to the Lower Paleozoic Anticosti Basin in eastern Canada. The basin history consists of a passive margin stage and a foreland basin stage. Preliminary simulation results indicate that no significant fluid overpressures were developed in the passive margin stage and during the early period of the foreland basin stage, but strong overpressures were developed within the foreland basin succession during the middle and late periods of the foreland basin stage. Fluid flow rates were generally slow, and thermal profiles were not significantly disturbed by fluid movement throughout the basin history. Potential source rocks of hydrocarbons were found in the foreland basin succession. The strong overpressures in the foreland basin succession could have been a major driving force for hydrocarbon migration from the source rocks to the underlying potential reservoir rocks.

May 1, 2001

By J. C. Li, Y. Zou, L. He

"The effect of rock joints is significant in characterizing dynamic behaviors of discontinuous rock masses. To reveal the relation between the transmission coefficient and the contact situation of the joint surface, an experimental study on stress wave propagation across an artificial rock joint was carried out using a modified Split Hopkinson Pressure Bar (SHPB) apparatus. All the bars and specimens were norite cored from the same site, and one surface of the specimen which contacted to the transmitted bar was sawn with a number of notches to simulate the artificial rough joint. According to a wave separation method, two strain gauges were mounted on each pressure bar at a specific spacing, then the incident, reflected and transmitted waves across the joints were obtained from the test data. It was found that the contact situation of the rock joint surface makes a different on the wave propagation. Finally comparisons of the transmission coefficients with different contact area ratios and different joint thicknesses were made respectively. The results show the effects of contact area ratio and thickness of joints on wave transmission.INTRODUCTIONJoints affect the dynamic mechanical behaviors of the rock masses significantly. When propagates across the rock masses, wave usually attenuates in amplitude and frequency due to the presence of the joint as a discontinuous interface in the rock masses. Rock joints are the main factor that affects the behaviors and properties of rock masses. Many researchers have focused on the mechanical properties of rock joints under quasi-static conditions. Nowadays, the effect of joint dynamic properties on wave propagation across rock masses is gradually taken into account in theoretical and numerical studies.The effective contact area, joint roughness, and properties of the asperities and filling materials have been found to influence the normal stiffness of joints (Bandis et al. 1983). As suggested by the International Society for Rock Mechanics (ISRM), the roughness of the discontinuities can be generally characterized by large-scale “waviness” and small-scale “unevenness” (Brown 1981). Many researchers focused on the roughness of rock joints that affects the mechanical properties of rock masses and wave propagation. For example, Brown and Scholz (1985, 1986) presented theoretically and verified experimentally a closure model of contact between two random nominally flat elastic surfaces, which showed that the joint closure property depended both on the surface topography and material properties. Pyrak-Nolte et al. (1997) presented the quantitative aperture data for three-dimensional interconnected fracture networks, which were imbedded in intact opaque rock samples several centimeters in length, using x-ray computerized tomographic (CT) imaging. Fardin et al. (2001) systematically investigated the effect of scale on the surface roughness of rock joints and concluded that samples should be equal to or larger than the stationary limit for surface roughness to be accurately characterized on a laboratory scale or in the field. Zhao et al. (2006) conducted excellent ultrasonic tests across intact cement mortar specimens, singlefracture specimens, and two-fracture specimens."

Jan 1, 2015

By A. W. Jacob

THE shatter cut, or burn cut as it is often called, is one in which the centre of the round is almost reamed out by drilling holes so close together that the blasting of a few holes shatters the rock embraced by all of them. The idea of shattering the centre of a face by shooting holes drilled parallel to one another is not new. Some miners have used this method for years past, when drilling quartz or a face near timber. But, they followed the age-old practice of first blasting the cut, then the square-up. It was not thought possible to shoot both together. In the case of machine men, the two largest contributors to silicosis are dust from drilling and dust from blasting. It follows, then, that material reduction of exposure to either constitutes an important step in lessening the incidence o silicosis. It was? the hope of being able to do away with the necessity of the men having to return early to a face, through dust concentrations of 60,000 to 80,000 particles per cubic centimeter, that aroused interest "in the shatter cut at McIntyre. Efforts to this end were successful. Now, with this kind of cut, all holes of a round are shot simultaneously.

Jan 1, 1942

By E. P. Wiechrnann, C. M. Castro, G. A. Vidal

In copper Eta plants the optimal current density setpoint depends on the electrolyte composition and temperature. However, conventional plants operate with large standard deviations. A value of 14% with current densities offsets up to ±50% is typical. For worst, during opencircuit or shortcircuit events this variation can be from -100% to +200%. Naturally, energy consumption and copper quality are compromised. Several devices have been successfully employed to reduce set point deviations. Last developments include; Optibar Segmented Intercell Bars, Outotec Electrodes Arranging Method and NTC Selective Electrodeposition Enhancers. This paper researches and compares these technologies. It is shown that short circuits can be effectively reduced in occurrence and magnitude. Moreover, 95% of the electrodes can be forced to operate within ±10% of the set point. The specific energy consumption is reduced from 2,000 KW per Ton to values close to 1,900 KW per Ton.

Jan 1, 2011

By A. E. Aho

"The Pacific Nickel property lies 7 miles northwest of Hope and 100 miles east of Vancouver, in the Coast Mountains of southwestern British Columbia. Nickel-copper sulphides were discovered in ultrabasic rocks on this property in 1923 and the deposits were explored by Pacific Nickel Mines until 1937, then again between 1951 and 1954 by Pacific Nickel Mines and by Newmont Mining Corporation through its subsidiary,Canadian Ore DepositsWestern Nickel. The property was studied by C. E. Cairnes (1) in 1924, by W. E. Cockfield and J. F. Walker (2) in 1933, by H. C. Horwood (3), (4) in 1936 and 1937, and by the writer in 1951 and 1952. Except for a few thousand tons for trial shipments, the property has never been mined. Indicated ore reserves now total somewhat over one million tons averaging about 1.4 per cent nickel and 0.5 per cent copper, with lesser values in precious metals and cobalt.GEOLOGIC SETTINGThe nickeliferous ultrabasic rocks form part of the core of a 15-milewide block of Late Palæozoic metamorphic rocks and Mesozoic intrusives which extend north-south between the coast batholith of British Columbia and the Chelan batholith of Washington. Margins of this block are faulted in part against less metamorphosed volcanic and sedimentary rocks largely of Jurassic and Lower Cretaceous age (Geo/. Surv., Canada, Map 737 A, 1942). Serpentinites, suggestive of deep transgressive structure, occur within the block, and also at its east margin along faults which are southern extensions of the regional Yalakom-Fraser River fault zone. Some of the other mineral deposits in the Hope area appear to be spatially related to these major faults.The mineralization at Pacific Nickel occurs almost exclusively within a stock-like mass of ultra basic rocks which mingle with, and partly cut, a larger batholithic mass of genetically related diorites and norites of late Mesozoic age (Figure 1 ). The ultra basic mass consists essentially of fresh, medium-grained hornblendic pyroxenite with peridotitic cores and with a remarkable margin of pegmatitic hornblendite. The most hornblendic rocks appear to be chiefly products of reaction and replacement of the pyroxene and olivine rocks. The mineralization consists of disseminated and massive pyrrhotite, with subordinate pentlandite and chalcopyrite, amongst fresh olivine, bronzite, and, Jess commonly, augite and hornblende. Both the ultrabasics and mineralization are cut by small hornblenditic and dioritic dykes, and by veins and alteration zones."

Jan 1, 1949