Search Documents

By Balakrishnan Nanthakumar, Marek Pawlik, Dennis Grimm

"The anionic flotation of a high-iron phosphate ore from Agrium - Kapuskasing Phosphate Operations was investigated through batch flotation tests in the presence of soda ash. The flotation data were supplemented by titration of the flotation pulp with soda ash, analysis of process water chemistry, and determination of the mineralogical composition of the ore. The results of lab tests were applied to the flotation circuit design allowing the flotation plant to efficiently process problematic ores. Process control measures (pH, conductivity) were also developed.Calcium cations and sulfate anions were identified as the dominant ions present in the process water when the difficult-to-process ores are beneficiated in the flotation plant. The concentrations of calcium and sulfate ions were consistent with the presence of a small amount of a calcium sulfate mineral in the ore although an oxidation/weathering process of iron sulfide minerals present in the ore could also be responsible for the observed water chemistry and subsequent flotation problems with the ores. The latter possibility suggests that the long-term stockpiling of such ores may have a highly negative impact on the flotation process.The role of soda ash in the flotation circuit is to precipitate metal cations from the pulp thus allowing the tall oil-based collector to selectively interact with the phosphate components.INTRODUCTIONPhosphorus minerals are the main source of this element for the production of fertilizers, and the froth flotation process is the most important technology for beneficiating phosphate ores. The flotation concentrate from Agrium-Kapuskasing Phosphate Operations (KPO) is transported to Redwater Fertilizer Operations in Alberta (also operated by Agrium) where the phosphate concentrate is converted into a phosphate fertilizer and other important chemical products. The KPO phosphate ores differ widely in mineralogy and phosphate grades, and are broadly divided on-site into three classes. The easy-to-float A-type ores do not pose any major flotation problems, but the B-type and “marginal” ores, which are quite common in the KPO igneous phosphate deposit, are not always readily-floatable using the current reagent suites and process parameters (pulp density, feed particle size, pH). In fact, marginal ores are presently considered impossible to process by flotation. A-type ores contain normally more than 15% P2O5 and less than 8% ferric oxide equivalent (Fe2O3). B-type ores are approximately of the same P2O5 grades as A-type ores but their iron content may reach 30% Fe2O3. Any material containing less than 15% P2O5 is rejected as waste rock."

Jan 1, 2008

By C. D. Shackelford, J. F. Muñoz, M. Vauclin, P. Rengifo, A. Suazo

The results of a field-scale study involving in situ leaching of copper ore tailings using sulphuric acid as the leaching agent, injection wells to introduce the leaching solution and extraction wells to recover the copper-enriched pregnant leaching solution are presented. The study was performed at an abandoned tailings disposal site using a battery of injection and extraction wells. The medium was characterized through the determinations of physical, chemical, mineralogical, and hydro-dispersive properties based on laboratory and field tests, including a tritium tracer test, a pumping test, particle size analyses, and hydraulic conductivity tests. Numerous horizontal strata with different hydraulic conductivities were identified. A previously developed model was used to simulate the leaching of copper ore tailings. Although the study confirms the feasibility of using in situ leaching for recovery of residual copper from tailings deposits, the efficiency of the technology depends significantly on the medium stratigraphy and hydraulic conductivity.

Jan 1, 2001

By P. Botane, A. Cailleau

"Compagnie Miniere Esperance operates a gold primary ore body. The ore is processed through crushing, grinding and gravity concentration generating tailings with remaining fine gold. Analyses of the tailings proved a residual gold grade sufficient for a chemical treatment.As lab tests proved the technical feasibility of a pre-concentration using flotation, an on-site pilot operation has been carried out to assess the continuous circuit performances, define the best configuration and obtain enough data for the industrial circuit sizing.Data collected during the pilot campaign have been used for calibrating a process simulator built with the USIM™ PAC software. The simulator validated the feasibility of upgrading the existing plant, including the reprocessing of tailings to obtain a good fine gold recovery in a small amount of concentrate. A preliminary capital cost has been achieved to assess the flotation workshop profitability.INTRODUCTIONCompagnie Miniere Esperance (CME), a mining company based in French Guyana, operates a gold primary ore body in open pit. The ore is processed through crushing, grinding and gravity separation in two stages: a top plant and a bottom plant. A “coarse” pond contains tailings of the top plant; this product feeds the bottom plant. Tailings of the bottom plant are stored in the “fine” pond.Analyses of the fine ponds proved a residual gold grade sufficient for a chemical treatment. However, direct cyanidation would require a too large installation, regarding the local conditions (accessibility, supplying and meteorological conditions).It has been then decided to test the feasibility of a pre-concentration using flotation. Lab tests have been carried out by SGS Lakefield (Canada) in March 2007, which proves the technical feasibility."

Jan 1, 2009

By Alfred W. G. Wilson

In this paper is presented a review of the changes that have taken place in certain Canadian non-metallic mineral industries since 1909. The fifteen-year period 1909 to 1923, inclusive, has been selected for two reasons. In the first place, statistical treatment of the subject under review has been nearly uniform throughout the period. In the second place, this decade and a half is itself further subdivisible into three well marked quinquennial periods, the middle one covering the period of the great war when industrial conditions were greatly disturbed. It then becomes possible to institute certain comparisons between equal periods before and after the war disturbances. The items selected for inclusion in this review are certain of the more important members of that class of minerals usually grouped together under the heading of non-metallics. They are all minerals of which Canada is known to possess important resources, and which are indispensable to many of our greatest manufacturing industries.

Jan 1, 1925

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, Hara, A. S. Kabir, R. Petrov

Manufacturing of thin sheet is difficult in industries. Some approaches, such as small-draft multi-pass rolling, intermediate annealing, isothermal rolling and high-speed rolling were proposed to overcome the deformability. In this study, different rolling speeds from 15 to 1000 m/min were employed to twin rolled cast AZ31B magnesium alloy to different reductions. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2014

By O. Peters, D. Lascelles, R. Caldwell

Ageing tests on a crushed Cu-porphyry ore were conducted to assess the impact of sample oxidation on flotation performance. The objective of the testwork was to simulate ageing of ore that would be blasted through block caving but not milled for possibly several months. Ageing was performed in specially designed columns, using site and deionised water to keep the samples moist over the entire ageing period. Samples from each ageing interval (0, 0.5, 1, 2, 4, and 8 months) were examined for physical and metallurgical changes resulting from the ageing process through chemical analyses, size analyses, and batch flotation tests.

Jan 1, 2009

By Walter Smith

Environmental Quality Committee ?EQC was created in 1995 to facilitate dialogue between industry and northern communities and help build the understanding of the industry in those communities. ?EQC is made up of representatives from 32 northern communities. ?Meet regularly with Cameco to discuss on going and new projects. ?Tour mine sites on a yearly basis.

Nov 1, 2011

By Joe Zhou

"Mineralogical characterization and metallurgical extraction of silver is challenging due to its complex mineralogy and chemistry. Over 200 Ag-bearing minerals have been identified and a silver-rich ore body would typically contain 5 to 10 different silver minerals. Silver can occur not only as discrete microscopic (visible) silver minerals but also as submicroscopic (invisible) silver in other minerals. During processing, silver may form passivation compounds such as silver hydroxide, silver sulphide, jarosite-like silver sulphate, silver halide or silver cyanide precipitate, all of which may negatively impact on silver extraction. Knowing the deportment of silver in the ore and its metallurgical products is important in flowsheet design and plant optimization. This paper begins with the classification of silver ores and minerals and a review of processing techniques, and focuses on the major mineralogical factors to explain why and how these factors affect silver extraction. Case studies are provided to demonstrate the application of silver process mineralogy in flowsheet design and plant optimization.INTRODUCTIONSilver was known to and utilized by mankind since ancient time. Actually, it was one of the earliest metals discovered and utilized by mankind after gold and copper.Silver is the whitest metallic element. It is rare, strong, corrosion resistant, and unaffected by moisture, vegetable acids, or alkalis. Silver is also resonant, moldable, malleable, and possesses the highest thermal and electric conductivity of any substance. The chemical symbol for silver is Ag, from the Latin argentum, which means white and shining. Although silver does not react with many chemicals, it does react with sulfur, which is always present in air at trace amounts. The reaction causes silver to tarnish, and consequently it must be polished periodically to retain its luster.Silver possesses many special physical characteristics and qualities that make it useful to a variety of industries. The photography industry is the biggest user of silver compounds. Silver forms the most light-sensitive halide salts, which are essential to developing highquality photographic prints. Silver also has the highest electrical conductivity per unit volume of any metal, including copper, so it is used extensively in electronics."

Jan 1, 2010

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By Webber. G. R.

Variation in content of some of the major and minor elements in the Lake Dufault granodiorite near Noranda, Quebec has been studied. The element variation and specific gravity data show a pattern consistent with the concept of a concentrically zoned intrusive on the western side of Lake Dufault with a potassium-rich core and a calcium-rich inner zone. The part of the intrusive on the eastern side of Lake Dufault is of more problematical origin, but the suggestion is made that it has resulted from assimilation of volcanic rock by the intrusive. THE purpose of this investigation was to test the application of x-ray fluorescence analysis to the study of variation in chemical com-position of the Lake Dufault granodiorite. The Lake Dufault granodiorite is an intrusive body approximately six miles long by three miles wide located four miles north of Noranda, Quebec. This intrusive is of particular interest because of its -

Jan 1, 1962

By T. J. Fee

Introduction The International Nickel Company have been pioneers in mine rescue work in Ontario. Following the fire in the Hollinger mine in the spring of 1928, the Company purchased ten self-contained oxygen breathing outfits, ten all-service gas masks, an oxygen high-pressure pump, life line, inhalator, ten cap-lamps with batteries, and a complete stock of spare and accessory parts. An instructor from the U.S. Bureau of Mines, Pittsburgh, came to the Creighton mine for one week and trained twenty men in the use and limitations of all equipment. Monthly training courses were commenced in the fall, and have continued to the present time. Of the original twenty men trained, ten are still on the Creighton mine rescue teams. In the meantime, and as an aftermath of the Hollinger fire, the Work-men&apos;s Compensation Board of Ontario and the Ontario Department of Mines established a central mine rescue station at Timmins. This was completed in the spring of 1930. It was then decided, in view of the great expansion in mine development in the Sudbury district, to build and equip a similar station to serve all the mines there, namely, Creighton, Frood, Garson, Falconbridge, Sudbury Basin, and Errington. An extensive survey was made and a central location selected opposite the Frood mine. The International Nickel Company donated a site, and the station was completed in the fall of 1930. The station is a two-storey brick building, 27 ft. by 47 ft., with a large garage adjoining it. The ground floor is used for equipment and for training the crews. On the second floor are living quarters for the superintendent and his family. The garage houses a closed truck, in which all necessary equipment can be taken to any desired point for training purposes or for actual mine rescue work, if and when necessary. The garage is also used as a gas room, where the men are trained in an irrespirable atmosphere. A gas-tight observation window between it and the training room enables the superintendent to see and direct the men undergoing training, weight exercisers and other devices being used.

Jan 1, 1935

By Lloyd Rowson

??Several factors have led to a review and reoptimization of the Midwest uranium deposit by AREVA Resources Canada Inc., the project operator, on behalf of the owners ??The current proposal is to mine the deposit using open pit methods and then transport the ore by truck on a dedicated road linking the Midwest site with AREVA?s McClean Lake Operation (JEB mill) for processing ??A decision has been made to begin mining the deposit by 2010 (pending regulatory approvals)

May 1, 2008

By K. Loutet, A. Guenkel, K. Nikolaisen

"The INCO SO2/air process was patented by INCO in 1985. Well over 80 mining operations worldwide are using this process to oxidize cyanides to cyanates in the tailings from gold, silver and copper mining operations. The sulphur dioxide (SO2) for this process can be supplied either as liquid SO2, SO2 gas or as a sulphite-based salt. The majority of SO2/air operations have used sulphite-based salts as the ‘SO2’ equivalent probably due to low capital cost. Liquid SO2 has also been used frequently, but due to concerns with safety and availability, this option is often not preferred. The solid salt sodium meta-bisulphite (SMBS) is commonly employed, but its cost is an order of magnitude higher than that of sulphur. Due to the high cost of SMBS, the increased capital cost for a sulphur-burning SO2 gas plant (green field or retrofit) usually has a pay-back of less than three years. In addition, a SO2 gas plant offers potential for significant heat recovery from the sulphur burning process. In terms of safety, the SO2 gas plant only requires the storage of relatively benign sulphur and the site inventory of SO2 will be limited to the plant gas volume. Therefore, a SO2 gas plant will not trigger the Canadian Environmental Protection Act (CEPA) E2 Regulations or the US Clean Air Act Section 112(r) accident prevention regulations, as may be the case for liquid SO2.Most existing mining operations using ‘SO2’ are gold operations, but in recent years there has been an increased interest in larger sulphur dioxide gas plants for hydrometallurgical facilities that employ leaching of cobalt/manganese minerals or precipitation of manganese/iron (e.g. Tenke Fungurume and El Boleo).This paper focuses on the production of sulphur dioxide gas generated on site and on demand for the use in hydrometallurgical processes. The capital and operational costs of a SO2 gas plant is compared to conventional process alternatives using sulphite-based salts or liquid SO2."

Jan 1, 2016

By Neo Molelekeng, Jocelyn Bouchard, Rebecca Monnapula, Martin Émond

"Xstrata Alloys – Eland Platinum concentrator (South Africa) has recently been commissioned and is now initiating a challenging optimisation program encompassing the entire operation. Process control improvements are key elements of the program and initial results have demonstrated how leveraging from current assets can bring significant improvements through overall reduction of variability. This paper gives a brief overview of the operations and details how Eland is striving to become a top tier leader with advanced regulatory control strategies recently implemented. Results reveal that what can be achieved in a standard control system (PLC or DCS) should not be underestimated as the first interventions led to a steadier operation of the primary ball mill circuit. Following the improvements, significant and sustained reductions of standard variation were observed for key process variables around their set-point: primary ball mill feed rate (72 %), rougher feed density (58 %), and rougher feed flow rate (47 %). A path forward has been identified to tackle further opportunities around the primary grinding circuit: water balance management, throughput optimisation as well as charge and power draw control.INTRODUCTIONThere are numerous approaches to mineral processing plant optimisation. As the benefits of determining the right reagent types, mix, dosage and addition points, or the proper charge of grinding media in a mill are fully appreciated, there is still nowadays some misunderstanding and misconceptions about process control in general and how it can contribute to the whole optimisation process. The confusion between the various disciplines involved, i.e. instrumentation, control system programming, automation and process control, certainly does not serve the best interest of the industry with this regard."

Jan 1, 2010

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Abstract-Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-chalcopyrite core - interlayered pyrite-sphalerite-galena (Pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyrite­ quartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone 1) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (Il and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone 1, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F1 fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By J. H. Archibald

"IntroductionShot-saws are used for sawing rock throughout the dimension stone industry especially in granite quarry mills. Shot-saws, as currently designed, have an inherent wear problem which leads to slow cutting rates and repetitive blade changes which consumes much time. Because the saw blades are made from steel the abrasive shot used with them is limited to a certain hardness which effects the over-all efficiency of the sawing operation. Suggestions are made toward optimization of blade design and the sawing process. Blade DesignA common steel blade design is shown in Figure I. Note the perforations in the blade. These perforations or holes in the blade serve two or three purposes. The most obvious reason is to allow the abrasive shot a pocket in which to collect at the bottom of the blade, so that it can be distributed from these pockets into the cutting zone underneath the blade. The abrasive is fed to the saw in a slurry and usually comes in from the top. The blade must then cut a kerf wider than itself in order that the abrasive grains have a path leading from the top of the blade, down along its sides, and finally reaching the pockets and cutting zones. This circuitous path followed by the abrasive leads to side wear on the blades and high friction which can lead to blade buckling in severe cases. However, the fluidized path of the abrasives down the sides of the blade serves another purpose which is a positive gain if conditions are properly controlled. The abrasive slurry interacts with the perforations of the blade, the blade itself and the rock. This gap and the perforations in the blade, which are fluid filled, are sites of constant shearing motion. Eddy currents form in these gaps and pockets which tend to stabilize the blade by setting up balanced hydrodynamic forces which otherwise might not form in a non-perforated blade. A stable blade produces a more uniform cut in the rock. The third and final reason for the perforations are to allow the blade to wear in such a fashion that new pockets are always being formed and, consequently, new cutting surfaces between these pockets are also formed."

Jan 1, 1993

By John Russell

"The South American mining community leads the world in recognition and adoption of the latest grinding mill relining technologies. Clearly this region has recognised the benefits of improved relining performance.Six of the seven RUSSELL TWIN 8 Mill Relining Systems, ordered to date, are either operating or being manufactured for South American mine sites.This paradigm shift, towards very short relining times, aims at displacing mill relining activities from the critical path of concentrator maintenance shutdown schedules.The first uses of the RUSSELL TWIN 8 Mill Relining System have seen some of the highest SAG mill new liner placement rates ever observed by RME, as would be expected with two, independent Machines working simultaneously in the one mill.The liner-replacement-rate, averaged over the whole reline, is good (27% improvement over single Machine System in the same mill) but short of full potential. This modest result can be attributed to reline crews unfamiliarity with RUSSELL TWIN 8 System operation.This paper compares a sample of conventional (single machine) RME Mill Relining System performance data with one ‘double head’ mill liner handler by others. Early performance of Escondida’s new RUSSELL TWIN 8 System performance is then compared with recent single Machine data from Escondida, immediately prior to RUSSELL TWIN 8 commissioning. RME and Escondida look to constantly improving RUSSELL TWIN 8 System performance as full operational familiarity is achieved.Also, the preparation of this paper revealed a need to develop a global industry standard for mill relining data collection. A web based platform, to develop and then distribute standardised data collection templates, is discussed in Annexure 1."

Jan 1, 2010

By Rodrigo Toro, Ivan Yutronic N

"The Copper Concentrator Plant of Compañía Minera Doña Inés de Collahuasi (CMDIC) is composed of three grinding lines, the third one being the largest. Due to the capacity feature of the third line, specially its SAG mill, it is a priority that the advanced process control team of the Company deploys a supervisory control strategy that allows this unit to operate in an optimal way, in order to achieve the maximum productivity at minimum cost. It is in this kind of tasks where advanced control applications play a key role in obtaining the best economic profit of the process.The advanced process control team, formed by people from Informatics, Automation and Operations of CMDIC have assumed the challenge of generating the transition from a manual SAG Mill 1011 operation (40 x 22 feet, the largest copper SAG mill of the world), to a fully automatic SAG Mill using a multivariable control strategy instead of a rule based on expert control system (widely used in industrial mining process control applications).Therefore, CMDIC decided to work together with Honeywell APC Team implementing an advanced automatic control strategy for the SAG Mill 1011, using for this purpose a technology called Model Based Predictive Control (MPC), based on a variety of control methods that uses dynamical models of the process, obtained from input/output data, in order to print the process knowledge into a group of mathematical relationships that links the constraints (controlled variables) with available commands (manipulated variables) and measured disturbances.The main objective of the advanced control strategy is to ensure process government, tending to throughput stability and optimization, by the execution of coordinated control actions, proactively avoiding measured disturbances effects and the SAG mill overloading.The most important benefits of using a multivariable control strategy are: the automated operation of SAG mill 1011 (that was manually operated before the implementation of this application), a safer, more coordinated and more stable process operation, achieving through this an increase of throughput and a decrease of specific energy consumption, controlling the amount of oversize material production, power consumption, mill loading, noise and torque. In addition to the operational results, this challenge has consolidated a control team, with the participation of engineers and operators, diminishing the typical implementation time and achieving a greater use of the application in a short time."

Jan 1, 2010

By D. DeGagne, E. De Souza, J. F. Archibald

This paper describes the potential use of anew agent material for backfill consolidation, ground waste glass, to be used as partial replacement of Portland cement fractions within backfill. Significant fractions of commercial and residential silica glass production is currently utilized as waste landfill and must be disposed of at high cost and with no foreseeable environ-mental benefit. This paper also demonstrates that waste glass materials could be effectively recycled as backfill additives, and that a significant, large and stable source of additive supply, currently land filled, can be developed. This new application will generate added value for such materials, serve to promote positive environ-mental stewardship and satisfy engineering sup-port requirements in mines.

Jan 1, 1997

By J. E. Sepulveda, R. Morrow

"In full scale mineral grinding operations, the steel balls normally utilized as auxiliary grinding media get to be consumed at different specific rates, as determined by 3 basic mechanisms: abrasion/corrosion (wear), impact ball breakage and impact surface spalling, the latter relating to the removal of rather small pieces of steel coming off the exposed surface of the balls due to repetitive impact with other balls in the charge or the surrounding mill liners. In conventional ball milling applications, the clearly predominant mechanism is gradual wear by abrasion/corrosion. In the case of SAG mills, where the make-up balls may be as large as 6”f diameter, breakage and spalling mechanisms are significant contributors to total ball consumption, although not to the extent of overriding wear mechanisms.Ball wear has been well characterized by the Linear Wear Theory, as presented at the last CMP 2014. Impact breakage has been customarily monitored, at the ball manufacturing site, via Drop Ball Tests (DBT) consisting of repeatedly dropping balls from a standard height and accounting for the number of broken balls and the weight loss (spalling) of the remaining unbroken balls. When properly conducted, DBT’s should provide meaningful indications of the breakage and spalling resistance of large diameter balls. The current publication is focused on the interpretation and projection of DBT results to full industrial scale, taking into account all 3 mechanisms of grinding media consumption in SAG mills.INTRODUCTIONA thorough, quantitative understanding of the independent contribution of all active grinding media consumption mechanisms is of the highest practical relevance, particularly in semiautogenous (SAG) milling operations where ball breakage and spalling can not be ignored or neglected, as it has been normally acceptable for conventional ball milling processes. The high severity impact conditions currently imposed in typical SAG mill environments create serious challenges to the manufacturers and suppliers of large diameter (5”–6”) SAG balls, whose products must be capable of surviving such harsh operational conditions with minimum breakage or spalling."

Jan 1, 2015