Search Documents

By Michael L. Free, Zongliang Zhang, Joshua M. Werner

In the copper electrowinning process, short-circuiting between the anodes and the cathodes is a critical problem that changes the current allocation among local electrodes and reduces the current efficiency significantly. Possible reasons for the short-circuiting include the improper alignment of the electrode, bent electrode, and nodules on the cathode surface. In typical tankhouses, there is often a time between shorting and harvesting as well as between shorting and clearing. Therefore, it is inevitable to have short-circuiting affect the operation performance in practical electrowinning operations. However, one key piece of missing data is the actual measurements of the current efficiency as short-circuiting is approached and allowed to continue. Consequently, short-circuiting tests that allow tracking of electrowinning parameters before and after short-circuiting were performed in a laboratory scale Cu electrowinning cell. In the tests, the electrode spacing change, the mass of electrodeposited Cu, the deposition morphology, and the current allocation as well as the current efficiency before and after short-circuiting were studied. Results show that the short- circuiting affects the current allocation and the current efficiency significantly. Moreover, it changes the Cu deposition on the short-circuited cathode and therefore causes problems for Cu electrowinning. INTRODUCTION Electrowinning (EW) is commonly used for copper production around the world, with a rated production from 120,000 to 200,000 tons per year per operation (Wiechmann, Aqueveque, Henríquez, Muñoz, & Morales, 2014). In Cu electrowinning, Cu ions in the electrolyte are reduced on the cathode surface as metallic copper with a DC current, while on the anode, a counter anodic reaction occurs with oxygen gas generation (Werner, Zeng, Free, Zhang, & Cho, 2018; Zhang, Werner, & Free, 2018; Zhang, Werner, & Free, 2018). In copper electrowinning, an average current density of 200 to 400 A/m2 is applied to the electrowinning cell (Wiechmann et al., 2014). As the Cu deposits on the cathode, the distance between anode and cathode reduces and most of the time, short-circuiting forms between some anodes and cathodes in a large tankhouse containing thousands of electrodes, reducing the current efficiency and increasing the energy consumption significantly. The current efficiency in well-run copper EW operations is typically above 90 %. Most of the unused current is wasted through short circuits, stray currents, and by-byproduct formation (Davenport, King, Schlesinger, & Biswas, 2002; Wiechmann, Vidal, Pagliero, & Gonzalez, 2002; Wiechmann, Morales, & Aqueveque, 2010). Usually, in the tankhouse, the short-circuiting increases the current in the involved cathode by up to 1500 A (Wiechmann et al., 2010). Multiple reasons can cause the short-circuiting in the cell, and the most common reasons include the uneven current distribution among cathodes, tilted electrodes, bent electrodes, and nodules formed due to the large deposition roughness. Recognition of this challenge in the Cu electrowinning process has led researchers to perform many investigations on approaches to avoid and reduce the short-circuiting in the cell. A series of research investigations have been conducted to develop and improve a new type of intercell bar for Cu electrowinning (Wiechmann et al., 2002; Wiechmann, Morales, Aqueveque, & Burgos, 2007; Wiechmann, Morales, & Aqueveque, 2009; Wiechmann et al., 2010; Wiechmann et al., 2014). The associated test results show that this new design limits the occurrence and magnitude of short circuits and allows operation at higher current densities. Sandoval, Clayton, Dominguez, Unger, and Robinson (2010) stated several keys to control short circuits, such as maintaining the straightness of the cathode, removing “edge hair” from the cathode starter, and maintaining electrode alignment in the cell. Prengaman and Siegmund (1999) from RSR technologies developed a new Pb-Ca-Sn anode to prevent the anode deformation, thereby reducing the short-circuiting in the Cu electrowinning cell. Although the negative effects of short-circuiting on the Cu electrowinning have been recognized, and various investigations have been conducted to address this issue, the actual measurements of the electrowinning behavior and performance as short-circuiting is approached and allowed to continue are seldom reported. However, in typical tankhouses, there is a time between when shorting occurs and harvesting/clearing are performed. One key factor in determining the harvest time is the frequency of shorting. Consequently, we have performed short-circuiting tests that allow us to track electrowinning parameters before and after short-circuiting.

Jan 1, 2019

By Grant J. Goddard

"The Iron Ore Company of Canada (IOC) has been in operation for over 30 years. Today, and in the future, technology and its application will play an ever more critical role in the company’s business success.The Carol Mining and Concentrating (CMC) division of IOC is energetically applying technology today to enhance performance and results, and is aggressively exploring opportunities to apply technology to support improved business results in the future.A critical area of focus is the application of technology to maintenance management performance. CMC has taken a “back to basics” approach to the fundamentals of maintenance management in 1995 and 1996. In parallel, the mine is aggressively implementing its Vision 2000 maintenance integration plan. This plan is targeted at levering the energies applied to sound maintenance management fundamentals as the company moves to a fully condition based maintenance approach.This paper discusses some of the strategies, key technologies and objectives of theVision 2000 maintenance integration plan at the mining operations of IOC."

Jan 1, 1996

By G. Dörsam, M. Spreij, S. J. Van der Wal, A. P. Schmidt

The transfer of hot metal desulphurising from the torpedo cars to the hot metal ladles at the IJmuiden BOS plant no.2 caused a decrease in ladle lining life from 680 to 470 heats. Changing the desulphurising agent CaC2 for CaO during a trial period, for environmental reasons, led to a further decrease in refractory life. Availability of the ladles became critical and the major reasons for the low life were identified. Solving one of them, temperature, quickly resulted in restoration of the original lives. However, re- introduction of the new desulphurising agent on 50% of the heats again resulted in a decrease, this time from 700 to 550 heats. In order to be prepared for the full introduction of the new agent, thorough investigation of worn linings was conducted, revealing the major (chemical) wear mechanisms. With these findings, a new design for the hot metal ladle is proposed.

Jan 1, 2004

By Roy O. Ifill, W. Charle Cooper, Alan H. Clark

"Queen’s UniversityIn representative, run-of-mine samples from the Panel and New Quirke mines of the Elliot Lake uranium district, Ontario, brannerite, ametamict uranous titanate, occurs in microscopic grain-aggregates which display wide variations, both in textural habit and in the relative proportions of brannerite, titania polymorphs and/or “uraniferous titania”. As is widely documented, much of the brannerite occurs as trellis-like arrays of laths and needles pseudomorphing rutile oranatase. In some cases, the laths and needles are cemented by coffinite. Brannerite, with an average composition of (U0.629Th0.039Ca0.20)(Ti2.199Fe0.13)O69contains =3 wt% Th and is distinctly Ti-rich relative to the ideal composition, UTi2O6. Much of the Si reporting consistently in electron microprobe analyses (between 1 wt%and 5 wt%) is tentatively attributed to contamination by the quartz-sericite matrix, and a minor proportion is attributed to the presence of coffinite intergrowths. “Uraniferous titania” (average par-tial composition by weight: 10.8% U, 0.3% Th,32.9% Ti) is considered to represent an intermediate stage in the conversion of titania to brannerite.The leaching behaviour of brannerite in its different modes of occurrence was studied qualitatively by the rotating-disc (polished section) method in H2SO4and HCl solutions at 25° to70°C. Redox potential was not measured. The progress of the dissolution of the individual brannerite crystallites and grain-aggregates was monitored by optical and scanning electron microscopes. Regardless of its morphology and texture (laths or needles, reticulate or blocky),brannerite is not readily leachable. Regardless of the process conditions, the rate-controlling step appears to be the initial leach-pit formation. These pits expand radially through the aggregate as leaching proceeds. This dissolution mode is independent of the relative amounts of brannerite and titania, i.e. the type of grain-aggregate. Secondary coffinite intergrowths are readily leachable and enhance the overall leaching kinetics of brannerite by accelerating leach-pit formation. These data provide, for the first time, information on the controls on the leaching of the uraniferous phases which dominate the lower-grade ores in the Elliot Lake district."

Jan 1, 1996

By Jakob Janzen

This paper demonstrates that the introduction of a Battery Energy Storage System (BESS) into an isolated diesel generator based grid has the potential to reduce the electricity cost and deliver a good return on investment. Energy storage also allows for increased renewable energy penetration, into the isolated grid, that further reduces the electricity cost. The isolated power system studied includes several diesel generators of different sizes. The typical operating pattern is for the generators to be run at 80% to 85% of their power rating to deal with load fluctuations. Operating the diesel generators near their full power rating, however, improves their efficiency, in this case, while the frequency and load control can be carried out by the BESS. Operating the diesel generators near their full power rating reduces the number of generators which need to be operating to support a given load. As a result, the improved efficiency of the diesel generators and reduced maintenance cost, for operating fewer machines, are the reason for the savings.

Aug 1, 2013

By S. C. Bouffard

Barrick's Zaldivar operation in Chile produces copper by heap leaching, solvent extraction, and electrowinning. The heap consists of a dynamic pad, and its stacking and operating conditions have changed over its 11 years of operation. These changes have included pad re-mining midway through the cycle, tightening of the irrigation drip lines, an increase of the coarseness of the particles, and an increase of the heap height. This paper reviews the heap operating data to understand the effects of these changes on the kinetics and recovery of copper minerals. Field tests demonstrated that neither re-mining nor tightening the irrigation grid added value for both low and high grade oxide and sulfide ores. The P80 of the feed ore was increased by 0.8 mm, which did not reduce the copper recovery of oxide and sulfide ores. The increase of the heap height above 8 m lowered moderately the copper recovery from sulfide minerals, and very slightly the recovery from oxide minerals. Despite the lower recovery, the higher tonnage stacked in the taller heap increased the copper output. Optimizing the chemistry of the agglomeration and feed solution holds more promise for increasing the copper recovery than the above physical changes.

Jan 1, 2007

By C Kumar

Scaffolds are temporary structures built to facilitate construction activities on site. A considerable amount of resources are allocated to scaffolding on industrial projects. Variability in geometrical features and space accessibility of structures on industrial projects, in addition to involvement of different trades that share the use of scaffolds, requires an extensive understanding of scaffolding requirements. Hence, it?s important to plan and estimate scaffolding man-hour requirements for the different construction areas on an industrial site. Contributing factors involved in such estimates include the list of trades that work in a construction area, trade working hours, volume of work, geometry of equipment erected, etc. A simulation template for predicting scaffold erection man-hour values for individual construction areas in an industrial project was developed in Simphony 4.0. The template is based on mapping the geometry of equipment and other factors to man-hours of scaffold work. The template facilitates the use of distributions as inputs and produces a range estimate of scaffold man-hours. The mapping is based on a linear regression model derived from existing project data from PCL Industrial Management Inc. The template is being further developed to incorporate the ability to predict scaffold erection schedule and material requirements based on construction work areas or equipment lists of an industrial construction project.

Aug 1, 2013

By Junior Santos

Kinross Paracatu started the operation of the new gold processing plant in the end of 2008, being composed by one SAG mill and two ball mills. During the first year of operation the plant had several problems related to stability and throughput capacity, mainly due to low grinding efficiency of the ball mills. In this period many actions were taken to maximize the throughput rate. Among the actions are reducing the size of balls in the mills, increasing the ball charge in the SAG mill, changing cyclone configuration and return of circulating load to SAG mill. With better stability of the circuit, the second stage of improvements has begun with the objective of increasing throughput rate and also reducing operation costs. Among the actions are the optimization of ball charge in the mills and a better operational control of cyclone parts. After two years of operation was obtained a significant increase in plant capacity, but still requires the addition of a third ball mill in order to maximize the use of SAG mill, which has spare capacity.

Jan 1, 2012

By E. A. Roux

As the first mine-to-metal zinc operation utilising atmospheric leaching, solvent extraction and electrowinning, Skorpion Zinc faces unique challenges and opportunities. One of these challenges is found in the solvent extraction circuit, in which di-ethylhexyl phosphoric acid (D2EHPA) is used as the organic extractant. Although D2EHPA is an excellent extractant for zinc, it suffers from the co-extraction of ferric iron, which is produced during leaching and by the corrosion of the grinding media. This situation is partially mitigated by iron precipitation in the neutralisation step prior to solvent extraction. Unfortunately, some ferric iron still reports to the solvent extraction process. This leads to a slow build up of iron in the organic phase. Chemical stripping is used to maintain the Fe concentration at an acceptable level. In this paper, the efficiency of the iron removal process is discussed.

Jan 1, 2006

By M. E. Holter

"Five main lignite seams occur in the Tertiary Ravenscrag Formation in the Eastevan area, at depths of 100 feet or less. They are named, in ascending order: the Boundary, Estevan, Souris, Roche Percee and Short Creek seams. A total sequence of approximately 250 feet is represented by the coal beds and interstratified clays, silts and sands. Strata dip to the southeast at 25 feet per mile or less and trike northeast. Large areas underlain by coal seams at shallow depths are delineated. Reserve calculations are dependent on detailed information on seam thicknesses and feasible stripmining depths. The stratigraphically higher seams are thinner on the average than lower seams and this, together with the increase in elastic size fractions in higher strata, suggests a retreat of a Tertiary marine margin to the south during the closing depositional history of coal seams and associated strata."

Jan 1, 1972

By W. B. Agocs

"AbstractThe airborne magnetometer data of the Marmora iron ore deposit at Marmora, Ontario, have been used as an example to show the mapped results obtained by the use of line spacings of from 1 mile to 14 mile. The maps are illustrative of the results which could be obtained from such line spacings for any type of geophysical survey, and they show the probability of 'missing' a feature of economic value if the line spacing is too coarse.The probability equations are given for the crossing of randomly oriented features whose maximum dimension is less than the spacing of the control lines for circular, elongate, and rectangular outlines. The equations are P = D/S; P = 2L/S; P = 2(L+W)/,.S; P = A/,.S; P = (2L(S+T)-L2),.ST; and P (D(S+T-,.D)) ST, respectively; where P is the probability; D is the diameter; L is the length; W is the width; and S and T are line spacings.IntroductionTHE EFFECT of station spacing, and the effect of the distance between the plane of observation and the plane of the source of the potential field anomalies, have been studied by geophysicists in the past.The purpose of this paper, however, is to illustrate the effect of line spacing •on the resultant mapped magnetic anomaly for a known magnetite mass, and to present the elementary probability equations for determining the optimum control spacing for detecting a particular type of feature. The effect of line spacing which is illustrated by the magnetic maps presented herewith would be comparable to results which would be obtained by any geophysical survey, since the contours between lines are of necessity interpolated."

Jan 1, 1955

THIS article describes the origin and details of a hydraulically operated switch to control the operation of an automatic underground pumping system. This system was installed in December, 1939, on the 2,350-foot level at No. 5 shaft of the Buffalo Ankerite mine. The pumping unit consists of an 8-stage centrifugal pump direct-connected to a 150 h .p., 2,200 volt motor. Pumping capacity is 200 gallons per minute under a 1,315-foot head and with a flooded suction. The control consists of a 200 amp., 2,200 volt oil-immersed starter with thermal overload protection, thermal protection on the pump, and a flow switch that is bypassed for 30 seconds after the pump starts. The 30-second time lag is operated by a relay mounted on the panel. There is a swing check valve in the discharge line of the pump which originally operated the flow switch by means of a connected outside lever which closed the switch as the check valve opened.

Jan 1, 1945

By A. Zarei-Hanzaki, S. M. Fatemi-Varzaneh, M. Haghshenas

The microstructure in modified semi-solid ALTHIX (A356) alloy consists of aAl phase with Al/Si eutectic structure. Silicon phase in eutectic structure is coral like with fine fibers. The lack of good ductility in this alloy is related to the presence of silicon fibers. Accordingly many investigations have been recently conducted to modify the Si morphology through Thermomechanical processing on this alloy. In the present work an ALTHIX (A356) alloy was deformed at 450°C, 500°C and 540°C through different strain rates. Consequently the silicon fibers were broken into small particles. The results indicated that the Si particles may coarsen according to Ostwald ripening mechanism at 540°C deformed by rate of0.0005 sec-1 & 0.0001 sec-1-

Jan 1, 2006

The extractive industry has the potential to impact the health and well-being of workers, families and surrounding communities. In the current environment of social performance, project planning considers that activities should be conducted in the best environmentally, socially and economically acceptable way across the development cycle (i.e. from exploration ? post-closure). In this context, health impacts of mining can be mapped and extend over the Life of the Community and can encompass worker injury and disease, exposure to communicable and non-communicable diseases, and health outcomes specific to family and community health and well-being outside the fence. To contribute to an emerging field focused on Health and the Extractive Industry, this paper reviews and compares health activities extracted from social and environmental reports published by selected major mining, oil and gas companies with operations in Australia and Canada. The objective of this review is to map corporate approaches to public health management across our previously developed Life-of-Mine within Life-of-Community (LOMLOC) framework in order to identify and compare trends and behaviour in corporate health investments across the project cycle, as well as identify the level of prevention targeted by this investment activity (i.e. primary, secondary and tertiary prevention of detrimental health impact). With the extractive industry facing ongoing rapid growth worldwide, this paper provides preliminary comparative information about corporate health spending by some companies in Australia and Canada. This information serves as a resource for minerals industry managers, civil society and regulators regarding current health management approaches in this sector.

Aug 1, 2013

By E. J. Marcotte

"IntroductionDevelopments in the preparation, hydraulic transportation and placement of classified mill tailing as an effective backfill and support for mining excavations, have made feasible several advancements in mining methods that are safer and more economical. Hydraulic backfill systems have played an integral part in the development of more efficient cut-and-fill and blasthole stoping.The hydraulic transportation of tailing fill has made possible the elimination of expensive and laborious transportation, placement and spreading of gravel type fills. Also, in cut-andfill stopes, the use of hydraulically placed consolidated fill has largely eliminated the need to use extensive timbering for floors and supports, previously necessary when only gravel type, waste rock or unconsolidated tailing fill was used .Another important advantage of using mill tailing as backfill is that it decreases the need to contain a large portion of the mill solids waste in a surface disposal area and thus reduces environmental and ecological problems.Tailing Fill PropertiesConsolidated tailing fill consists of deslimed mill tailing and Portland cement. These two materials are mixed together in various proportions to form a high density slurry which is transferred underground by gravity through boreholes and pipelines. After placement underground, the water is drained off and the mixture is allowed to set. The strength of the consolidated fill is dependent on the cement content, particle size distribution and curing time. A typical tailing/ cement ratio used for bulk filling in stopes requiring vertical wall support is 30:1. Ratios ranging from 8:1 to 5: 1 are used for stope floors. High pulp densities minimize segregation and loss of cement during placement as well as reduce the amount of drainage water to be handled."

Jan 1, 1989

By Robert B. Parsons

"There is a widespread concern that certain of Finance Minister Michael Wilson's Tax Reform proposals will likely lead to a significant decline in flow through funding after 1988. This does not bode well for the junior exploration sector, which relies heavily on flow-through to finance exploration programs. The exploration industry is actively pursuing various solutions to the problems posed by Tax Reform, in order to ensure that flow-through has a future.IntroductionWhile the proposals contained in Finance Minister Michael Wilson's Tax Reform White Paper may not be as far-reaching as some people had expected, nevertheless the combination of the existing tax rules and proposed new rules offers sufficient complexity to keep pencils sharpened for many months. After having had an opportunity to study Tax Reform since June 18, 1987, the sharpened pencils are suggesting that the White Paper is not without its shortcomings and pitfalls. Insofar as the mineral exploration industry is affected, there is widespread concern that adoption of certain Tax Reform proposals could spell near disaster for mineral exploration in Canada. More specifically, there seems to be a consensus among the industry, as well as some federal and provincial government officials, that the announced phase-out of the ""mining exploration depletion allowance"" (MEDA) would reduce the appeal of flow-through shares to the point where only a fraction of exploration funding would be financed in the future by flow-through."

Jan 1, 1987

By A. Bowles

The process of accumulative roll bonding (ARB) has been applied to wrought magnesium alloy AZ31. Accumulative roll bonding results in severe plastic deformation of sheet material. In AZ31, this process leads to the refinement of the microstructure by dynamic recrystallization. The refinement of the microstructure results in an improvement in mechanical properties with potential for producing materials for superplastic forming. In this work AZ31 was bonded with up to 64 layers and the potential of roll cladding with aluminium was also investigated. The development of microstructure and the mechanical properties are reported here.

Jan 1, 2006

By C. R. Tang

The respirable dust real-time monitoring equipment export information is complex, and electromagnetic wave wireless transmission is affected largely under mine conditions. The respirable dust concentration information transmission method based on led light equipment is proposed. The respirable dust concentration data of the individual real-time monitoring equipment is encoded to fit the system transmission; the encoded signal is modulated onto the LED mine lamp; the light signal is transmitted by the spatial channel; the signal is received by the receiver to the photoelectric conversion to restore the respirable dust concentration data for subsequent processing. Simulation and verification experiments showed that the respirable dust concentration information transmission method based on led light equipment can achieve the LED miners? lamps visible light wireless data transmission.

Aug 1, 2013

By The Staff

"IntroductionThe difficulties to be overcome in shaft sinking and development at depth are centred at McIntyre in and around No. 12 shaft. Generally they have been due to increasing pressures and temperatures and to changes in geological structure. This paper describes the difficulties and the measures taken to meet them.No. 12 ShaftEarly in 1932 McIntyre decided to sink an internal shaft from the deepest level, the 3875, to explore and develop known veins extending below that horizon. The location selected was a point 1,500 feet south and 1,000 feet east of No. 11 shaft, the main operating shaft through which the men, ore, and most of the materials are handled Shaft and auxiliary equipment we1e laid out for 3,000 feet, that is to 7,000 feet below the surface. The shaft was to be capable of handling 1,500 tons of ore daily from the lowest level, and was to provide ventilation, compressed air, water, and electric power to service all levels.No. 12 is an internal, vertical shaft extending from the 3875 to the 6825 level and bottoming at 7,007 feet. It is a rectangular, four-compartment shaft, 21 ft. 9¾, in. by 6 ft. 3¾ in. outside the timber (Figure 1).There are two hoisting compartments and one airway compartment, each 4 ft. 10¾ in. by 5 ft. ¾ in. inside dimensions, and a combined manway, pipe, and cable compartment 4 ft. ¼ in. by 5 ft. ¾ in. Levels have been established at 150-foot intervals, pump stations and sumps at 1,000-foot intervals, and. there are two loading pockets, one at the 5525 and the other at the 6900 level.The shaft was sunk in two stages. The first stage, consisting of preparation above the 3875 level and sinking to 5585 feet, was completed by March 31st, 1935. The second stage of deepening the shaft from 5,585 to 7,007 feet was started August lst, 1946, and completed three years later."

Jan 1, 1950

By J. Stachulak

In recent years more emphasis has been placed on the control of nitrogen dioxide (NO2) emissions from mining diesel equipment. Worldwide, diesel engine regulations to control emission and protect the environment are also driving the development of the diesel engine technology to reduce oxides of nitrogen NOx (Nitric oxide, NO + NO2). NOx are toxic gases produced in mines during the operation of diesel equipment. Most of the diesel equipment used in underground operations are equipped with Diesel Oxidization Catalysts (DOCs) designed to reduce carbon monoxide (CO) and hydrocarbons (HC). The effects of DOCs on NO2 production from diesel powered equipment is not well understood. DOCs do not alter NOx concentration, but may promote the oxidization of engine exhaust NO to the more toxic NO2, thus increasing the undesirable NO2 exposure of workers in the mine environment. In 2012, the ACGIH reduced the NO2 TLV concentration value from 3 ppm to 0.2 ppm. Vale and CanmetMINING have been involved in several research projects to reduce diesel emissions exposure to workers. One aspect of the current program is to determine the effects of in-use DOCs on NO2 production. Several in-use DOCs taken from mining equipment were selected for testing in the laboratory using ISO 8178-C1 and mine LHD transient test cycles. The paper presents the laboratory test results and effects of DOCs on NO2 production. The results indicate significant reductions in CO concentration, by over 77%, while increases in NO2 varied from 46% to 315% based on the ISO 8178-C1 8-mode steady state test cycle. The mine LHD transient test cycle showed the same pattern, although the magnitude of CO reduction was less. Consequently, it is recommended the use of only those DOCs that have been properly evaluated and shown not to significantly increase NO2 emission in the environment be used on mine equipment.

Aug 1, 2013