Search Documents

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978

"Here, we statistically proved that giant earthquakes occur at lunar phases specific to each subduction zone. Enough attention during the lunar period, especially when seismicity is occurring, will significantly reduce damage from giant earthquakes. Two case studies in which giant earthquakes occurred after seismicity in dangerous lunar phases were discussed, and the mechanisms underlying why giant earthquakes occur around neap tide at some subduction zones were explained by prohibition of giant earthquake occurrences due to high strain rates at spring tides at N–S subduction zones. The prohibition was statistically proven for uniaxial creep tests on Inada granite with slight stress disturbances. INTRODUCTIONIn previous studies, we showed that from 1900 to present, giant earthquakes (MW ??8) have occurred at lunar phases specific to each subduction zone (Fujii & Ozaki, 2012; Ozaki & Fujii, 2012). Although we later proposed a possible reason for these occurrences, the study lacked statistical analyses (Fujii et al., 2013). Therefore, this paper shows the results of such statistical testing and presents case studies for the Tohoku 2011 and Chile 2014 events, thereby providing updated data on giant earthquakes through July 2014."

Jan 1, 2015

By Hongpu Kang

The fully mechanized top coal caving mining method has been the main mining approach for thick coal seams with high output and efficiency in Chinese coal mines. The gateroads for the top coal caving mining faces should be driven along the floor of the thick coal seam with a part of the seam as roof. The support of the gateroads is commonly difficult because of the low strength and broken structures of the coal seams, and the increasingly large section of gateroads meeting the need of greater and greater face coal output. Based on the analyses on the geomechanics properties and production conditions of the top coal caving mining, the influences of the top coal caving mining parameters on the stability of gateroads, including mining thickness and face length, are studied. The deformation and damage features of the rock mass surrounding the gateroads with the top coal seam as roof are investigated, the interaction of the support with the surrounding rock mass, the support theory are studied. The bolting design method and criteria, bolting forms and parameters for the gateroads with the top coal as roof are put forward. The rock bolting components, including bolt bars, face plates, cable tendons, meshes, and steel straps, are introduced. Finally, the gateroad bolting effects are evaluated through a typical case study on the basis of field monitoring data, such as the displacement of surrounding rock mass and the forces along bolts and cables.

Aug 1, 2013

By The Mill Staff

"IntroductionCOMMENCEMENT of operations at the new No. 7 shaft and 10,000-ton mill at Creighton mine was a major step in the programme of conversion to all-underground mining by the International Nickel Company of Canada, Limited. Planned ten years ago, the orderly transition has been greatly speeded-up to offset the heavy drain on production imposed by World War II and also to meet the increased demand for nickel caused by the current international situation. Development of new mining methods, and process changes in the reduction plants, have made possible the economic recovery and utilization of ore of lower grade than formerly used and of varying metallurgical characteristics. By 1953, when the Company's open-pit mining operations are scheduled for completion, the hoisting capacity of its five underground mines in the Sudbury district will have been increased to 13,000,000 tons per year, compared with 5,700,000 tons of underground ore hoisted in 1950.Two types of ore occur at Creighton. One is a breccia and stringer type that contains a high percent-age of massive sulphides and is located in sheets along shears and in large and small pockets on the underside of the main norite mass; the other type, forming the main part of the ore zone, is mineralized norite that occurs as a •sheet up to 400 feet thick overlying tl1e breccia ore. In both types of ore the minerals of economic interest are pentlandite, which is intimately associated with pyrrhotite, and chalcopyrite. Early mining was confined to the breccia ore; this ore was mined by open stoping methods. The hanging-wall was later allowed to cave, with the result that the old stopes are now filled with caved low-grade ore."

Jan 1, 1952

By B. Panton, J. Carvalho, E. T. Brown

High-capacity, post-tensioned anchors have found wide-spread use in initial dam design and construction, and in the strengthening and rehabilitation of concrete dams to meet modern design and safety standards. Despite the advances that have been made in rock mechanics and rock engineering during the almost 80 years in which post-tensioned anchors have been used in dam engineering, some aspects of the rock engineering design of high-capacity rock anchors for dams have changed relatively little over the last 30 or 40 years. This applies, in particular, to the calculations usually carried out to establish the grouted embedment lengths required for deep, post-tensioned anchors. These calculations which involve a number of aleatory and epistemic uncertainties, usually make simplified assumptions about the distribution and values of rock-grout interface shear strengths, the shape of the volume of rock likely to be involved in uplift failure under the influence of a system of post-tensioned anchors, and the mechanism of that failure. The resulting designs are generally conservative. These aspects of the rock engineering design of large, post-tensioned rock anchors for dams could be improved by making greater use of modern, comprehensive, numerical analyses in conjunction with 3D models of the rock mass structure, realistic rock and rock mass properties, and the results of prototype anchor tests in the rock mass concerned.

Jan 1, 2015

Iron control and iron residue management and disposal are significant issues in all zinc production processes. This paper briefly reviews the most important primary zinc production routes and discusses the challenges posed by iron control in each of them. The technologies and strategies that have proven successful in controlling and managing iron are discussed. SNC-Lavalin's experience in designing and commissioning zinc plants provides a unique perspective from which to review this aspect of zinc production.

Jan 1, 2006

By G. H. Agnew

When water floods are initiated after gas-oil ratios have increased, the transition period from the start of injection until" the gas-oil ratios are returned to the solution gas-oil ratio may be important for either economic or technical reasons. The transition period is longest, and consequently most critical in water floods where injection is equal to withdrawals. This paper describes a theoretical basis for predicting the behavior of such a system and outlines a procedure for making the necessary calculations. The calculation procedure is illustrated for two actual cases: a line drive water flood and a five spot water flood. In each case there is a reasonable similarity between the actual and calculated performance.

Jan 1, 1960

By Brad Bjornson, Geoff Stevens, Mike Ashar, Cliff Britch

"LocationThe facilities are located 30 km north of Fort McMurray, Alberta (or 470 km northeast of Edmonton, Alberta).Brief Description of OperationThe operation includes the mining of oil sands, extraction of bitumen from the oil sands, and upgrading of the hydrocarbon fraction prior to shipment via pipelines to refineries.HistorySuncor was initially called Great Canadian Oil Sands. It was started by Sun Oil of Philadelphia. Construction began in 1965, with the first production coming on September 1967.Details of Present Milling Practice (Plant 3)Plant 3 recovers bitumen from the oil sand using the Clark hot water process. The basic steps in the process are conditioning, primary recovery, secondary recovery and tailings oil recovery.Oil Sand Feed SystemThe oil sand feed from the mine is transferred to the feed bin in extraction by two conveyor systems. Oil sand analyzers on each conveyor system measure the amount of bitumen and fines in the ore. Cones at the bottom of the feed bin distribute the oil sand to five process lines. Feed flow from each cone is regulated by an apron feeder which transfers the oil sand to conveyors that discharge into the conditioning drums. Weightometers on each of these five conveyors measure the rate at which the oil sand is delivered into the drums. The oil sand feed rate to each drum can be adjusted by varying the speed of the apron feeders."

Jan 1, 2000

By M. Turner-Jones, N. Steenekamp

"The Lonmin Base Metal Refinery treats converter matte from the Lonmin Smelter to produce nickel sulphate crystals, copper cathode as well as a concentrate containing the platinum group (PGM) metals. The original process employed a Sherritt design and utilizes atmospheric and pressure leaches for the dissolution of base metals. This paper describes the original flow sheet and the improvements made to enhance PGM recoveries, product quality and to increase capacity. Changes include the introduction of flash recycle cooling on the autoclave, batch leaches to improve the quality of the PGM concentrate and the implementation of solid-liquid separation with centrifuges. INTRODUCTIONThe Lonmin Base Metal Refinery (BMR) is about 100 km north-west of Johannesburg and treats converter matte from the Lonmin Smelter to produce nickel sulphate crystals, copper cathode and a concentrate containing the PGMs. The plant was commissioned in 1985 based on a Sherritt design to treat 12 tonnes converter matte per day. The original flow sheet consists of a milling circuit, an atmospheric leach and a pressure leach to produce a PGM concentrate which is despatched by helicopter to the Lonmin Platinum refinery in Brakpan, about 40 km east of Johannesburg. The liquor from the atmospheric leach is treated by crystallization to produce a nickel sulphate hexa-hydrate crystal. The leach liquor from the pressure leach is treated by a selenium removal step followed by electro-winning to produce copper cathode. The spent solution from the copper electro-winning is recycled to both the atmospheric and pressure leach steps to provide sulphuric acid for the leaching reactions.Modifications were made to the original circuit to increase the plant capacity, to improve the PGM recoveries and to improve the quality of the PGM concentrate. Capacity increases included all the unit operations, new mill, new first stage, additional autoclaves, additional nickel sulphate crystallizers, new copper electro-winning and new batch leach reactors for upgrading the PGM concentrate. The current circuit is described in this paper and not the detailed history of each plant change."

Jan 1, 2012

By A. Ehsani

"Seas and oceans constitute about 70% of the earth’s surface. They contain an enormous stock of various mineral resources such as sedimentary (marine placers), massive sulfide ore deposits, manganese nodules and cobalt-rich ferromanganese crusts. Sea and ocean floor ore deposits could well contribute to the meeting of ever-rising demand for raw materials in the metal industry. In this regard, more research and development in science and technology appear to be required to ensure maximum benefit from the mineral resources of seas and oceans. Since the 1960s, a variety of mineral and metallurgical processes have been studied and developed to deal with marine ores and to extract metals such as gold, nickel, copper, cobalt, manganese, tin, platinum group metals (PGM), zirconium, thorium, etc.In marine environments, there are many parameters which can affect the selection of the mineral and metallurgical processes. These include the extent and grade of the deposit, mineralogical and chemical properties of the deposit, and physical properties of minerals present with particular reference to particle size distribution and mineral liberation size.In this paper, we briefly review the latest trends in processing and extraction of marine mineral resources. Mineral processing technology is mostly applied for recovery of precious metals i.e. gold and PGM, in particular, from marine placers. In general, pre-treatment (sizing, classification, dewatering), gravity concentration techniques (shaking tables, spirals, jigs, etc.,), flotation, magnetic, and electrostatic separation are the options for enrichment of marine placer ore deposits. In the case of massive sulfides, manganese nodules/cobalt-rich crusts, hydrometallurgical and pyrometallurgical methods (as proven technological methods) can be exploited for extraction of metals from concentrates after physical separation or directly from marine ores. The hydrometallurgical treatments involve acid (e.g., sulfurichydrochloric) and alkaline (e.g., ammonia) leaching with different reducing agents and pre-treatments such as roasting. Alternatively, pyrometallurgical treatments involve mostly smelting, chlorination and segregation processes."

Jan 1, 2016

By Mohamad Kharseh

There is general acceptance that climate change, which is the most important challenge facing humanity, is anthropogenic and attributed to fossil fuel consumption. Therefore, improving the performance of our existing energy systems and deploy more renewable energy resources is an urgent issue to be addressed. Geothermal refers to existing of heat energy in deep rock and sedimentary basins. This energy can be used to drive a power turbine to generate electricity. Traditionally, geothermal has been exploited in places with the plentiful hot water at relatively shallow depth. In the light of fact that ground temperature increases with the depth everywhere on the Earth, engineered geothermal systems (EGS) can be installed in any place to exploit the geothermal in generating energy. Unfortunately, the high exploration and drilling costs of boreholes is the main barrier to commerciality of EGS worldwide. In addition, there are technical problems associated with drilling big depth. In oil producing countries such problems can be addressed by utilizing whether active or abandoned oil or gas wells and, consequently, EGS can produce power at profit. The current study presents an analysis of a binary geothermal power generation system for commercial electricity generation in Qatar. For this purpose, two binary cycles are assumed the main difference between them is that the first one is air cooled while the other will be water cooled. The performance of the two cycles and the possibility of improvement has been shown. Economic analysis the power plant shows that the levelized costs of electricity is 3.6US¢/kWh and the pay-back time is less than 8 years.

Aug 1, 2013

By D. C. Fraser

Copper occurs invisibly in a geo-logical environment characterized by swampy conditions and an accumulation of forest peat. This swamp, located in southeastern New Brunswick, contains up to ten per cent cop-per (dry weight), in the organic sediments. This occurrence appears unique in that the metal is apparently organically combined in a chelate compound. Unlike the acidic nature of most peat bogs, the pH of the cup-riferous peat is nearly neutral. Analyses of the peat and associated soils have indicated that the bulk of the copper is contained in the organic sediments. It appears that the cop-per distribution is affected by capillarity, evaporation and the growth of frost crystals, and that the copper fixation is effected by organic sequestration resulting in the metal being bound to the nitrogen or oxygen components of the forest peat. While such a fixation mechanism is not definitely established as responsible for the immobilization of the metal, the facts at hand are compatible with

Jan 1, 1961

By W. Zieman

"The low consumption of reagents can probably be attributed to a good clean type of ore. The cyanide level is kept at 0. 8 lb/ ton of solution and the lime at 1. 8 to 1.9 lb per ton of solution (pH 12. 2 to 12 .3). Experience in cutting down the lime level in half produced troubles in the presses, in the refinery and resulted in higher cyanide consumption. Finally the residue increased under these conditions, High lime always seems to prevent the trouble from occurring.A survey at one mine of the taxable work, performed in the mine shops for use in the mine, showed that under the new regulations, this had increased some 30 times what it was before the new rules came into effect on June 14, 1963.A water softener idea is incorporated at Lamaque with the crude addition of 100 lb of lime per shift to a spare agitator to precipitate the bicarbonates as carbonates from the water before it enters the mill. The lime titration of the softened water is about 0,2 to 0.3 lb per ton of solution (pH 11). This water is used mainly on the filters as washes."

Jan 1, 1964

By C. H. Ash

"The Red Chris Cu-Au deposit (522.7 Mt at 0.35% Cu and 0.27 g/t Au), northwestern British Columbia, is one of several pre-accretionary porphyry systems in the Cordillera of westernCanada. It is hosted by an Early Jurassic hornblende monzonite to quartz monzodiorite porphyry which forms part of a suite of dikes and stocks that intrude Late Triassic volcanic strata. Major and trace element chemical data suggest that these Early Jurassic intrusions have compositions which fall on the boundary between alkalic and calc-alkalic compositions. Alteration and mineralization in the Red Chris deposit are more typical of calc-alkaline porphyry systems with abundant potassic, sericitic and argillic assemblages and quartz-rich stockworks. It lacks Na- and Ca-bearing silicate assemblages which characterize the alkalic porphyry deposits of British Columbia. One of the more unusual features of the deposit is the abundance of carbonate alteration and veins which occur throughout the hydrothermal history of the deposit. This type of alteration and veining is more typical of alkalic porphyry deposits.The composition of the carbonates vary both temporally and spatially with different alteration zones. Potassic zones, which are characterized by orthoclase±albite±quartz±chalcopyrite±bor-nite±magnetite±hematite and Au/Cu ratios of 1:1 (g/t Au:% Cu), contain minor siderite veins and alteration. Quartz-sericite-carbonate (QSC) zones overprint earlier potassic alteration and comprisequartz+ankerite+sericite+pyrite+chalcopyrite with Au/Cu ratios of 0.5:1 (g/t Au:% Cu). Ankerite isthe main carbonate in this stage but has a variable composition with a more Fe-rich variety associated with mineralized veins. Localized chlorite-carbonate alteration zones, characterized by chlorite+carbonate+quartz±kaolinite±pyrite±gypsum and high Au/Cu ratios [2 to 3.5:1; (g/t Au:% Cu)],contain predominantly calcite. Late stage carbonate-gypsum veins have an ankerite to dolomite com-position which is very similar to the regional carbonate alteration and veins."

Jan 1, 1997

By T. Sun, J. Kou, C. Sun, China Railway Resources Group Limited

"The polymetallic sulfide ore in Jiama county of Tibet contains 0.78% Cu, 0.046% Mo, 0.31 g/t Au and 17.9 g/t Ag in average. However, heavy loss of valuable metals was observed using high-pH process and Butyl xanthate as the collector. In this paper, the flotation was optimized through the adoption of a novel collector C-7, which is a mixture of xanthate ester and thionocarbamate. This collector showed better flotation performance under weak base conditions. The recoveries of Cu, Mo, Au and Ag increased to 93.24%, 84.60%, 78.13% and 75.41%, respectively, under 15 g/t of C-7 at pH of 8.0. The adsorption mechanism of C-7 was investigated by micro-flotation tests, zeta potential measurements, FTIR analysis and adsorption quantity measurements. Chemisorption of C-7 on chalcopyrite surface is demonstrated with adsorption density 3.8 times higher than on pyrite.INTRODUCTIONXanthates are the most commonly used collectors of strong collecting ability for separating copper sulfide minerals from gangue in froth flotation. However, the selectivity of xanthates themselves is poor to realize separation of chalcopyrite and pyrite whose floatability are quite similar (Heyes & Trahar, 1977; Chandraprabha, Natarajan, & Modak, 2004). High pH process with xanthates as collectors is proved effective in copper-sulfur separation and is widely used in treatment of copper sulfide ore flotation (Smith, 1996; Valdivieso, Cervantes, Song, Cabrera, & Laskowski, 2004). This method could get ideal separation results, but large amount of lime must be added, and could bring about increased cost, device corrosion and environmental pollution. In addition, there could also be high depression and heavy loss of associated noble metal such as Mo, Au and Ag. Consequently, a large amount of research has been conducted on substitutions of xanthates for selective flotation of copper sulfide ores under low pH conditions (Gholivand, Khodadadian, & Ahmadi, 2010; Li, 2010)."

Jan 1, 2016

By J. L. Miller, R. W. Burns

This paper sets out the various phases of bringing a merchant bar mill into operation from feasibility consideration through financing, design and scheduling to completion.

Jan 1, 1967

By M. Gyenge, O. F. Coates, K. Barron

"It is suggested that artificial supports might be used to increase, with safety, the angle of hardrock open-pit slopes. Guidelines for designing such a support system, based on a simplified analysis, are given. The installation, construction and instrumentation of a trial support system is described and a breakdown of the construction costs is given. On the basis of this cost analysis, the economic benefits derived from reduced waste-rock excavation are compared with the support costs for a typical mine. In an example, it is shown that the slope angle in an open-pit mine 500 ft deep, with benches 50 ft high by 30 ft wide, could be safely increased from 37Yz degrees without support to an optimum of 53 degrees with support. In this case, the support costs would be approximately $900 per linear foot of pit wall and the savings due to decreased excavation of waste rock (at $0.34/ton) would be approximately $1,900 per linear foot, yielding an increased margin of profit of approximately $1,000 per linear foot of pit wall. This figure could be increased to $6,000 per linear foot if the steeper slope were used to extract more ore.More than 50 per cent of the support costs are accounted for by diamond-drilling the holes for the deep cable anchors. The use of percussion drills for this purpose would seem to offer a means of significantly reducing the support . costs and thus further increasing the profit margin available."

Jan 1, 1971

By C. J. Mwenifumbo

Preservation of groundwater quality is a major environmental concern. The disposal of hazardous material from urban waste dumps, milling wastes in tailings ponds, and industrial wastes in injection wells may contaminate potential sources of potable groundwater. The containment or migration of contaminants in the subsurface depends on bedrock characteristics and type of overlying sediments. Fractured bedrock and permeable sediments that may provide pathways for the transport of potentially harmful contaminants should be avoided when selecting a disposal site. The role of borehole geophysics in hazardous waste-site investigations is reviewed in three categories: (I) site selection; (2) determination of the extent of contamination at existing sites; and (3) long-term monitoring of migration of contaminants. In the first category, borehole geophysical techniques developed for lithology and fracture identification, and for porosity determination, provide some of the necessary information for understanding the subsurface hydrogeology. Lithological information can be obtained from gamma-ray, electrical resistivity, induction, magnetic susceptibility, and sometimes induced polarization logs; fracture detection and characterization can be accomplished with the use of caliper, density, resistivity, temperature, and acoustic televiewer logs. Estimates of porosity are derived primarily from neutron-neutron, resistivity, density, and soniclogs. Borehole geophysical techniques used in water quality determinations include self-potential, fluid resistivity, Eh (redox potentials) and pH measurements, and these can be used to map the extent of contamination at an existing waste site. Cross borehole and borehole-to-surface electrical methods can also be used in this application. Long-term monitoring of contaminant migration in boreholes can be accomplished with techniques that respond to changes in electrical conductivity, temperature and fluid chemistry caused by the presence of contaminants.

Jan 1, 1993

By M. R. Coffin

In recent years, improved operation of the Kidd smelter has resulted in an increase in blister production capacity. Due to manpower and equipment limitations anode production and treatment rates could not be increased without incurring significant additional operating expenses. The option chosen to expand casting and refinery capacity to meet the available blister supply was to increase the anode thickness while maintaining the same anode exchange cycle in the refinery. This has resulted in a cathode production increase of almost 10% for minimal expenditure. Equipment and process modifications required to cast and refine the thicker anodes are discussed in this paper, along with the Six Sigma methodologies used to identify them. Key areas covered are Hazelett continuous caster operation, refining process parameters, plating performance and cathode quality.

Jan 1, 2007

By V. G. Papangelakis, G. A. Moldoveanu

"Rare earths adsorbed on clay minerals are easily recovered via ion exchange during leaching with inorganic monovalent salt solutions. The leaching efficiency of various salts at 0.5M and 25°C was investigated as a function of cation type and salt system (sulphates vs. chlorides). (NH4)2SO4 was identified as the lixiviant of choice and a procedure was established to investigate the influence of lixiviant concentration, temperature, pH and agitation on desorption kinetics and REE extraction levels. It was determined that the kinetics were fast and the optimum leaching conditions (for >80% total REE extraction) required pH below 5 and moderate temperatures (<50°C). INTRODUCTIONRare earth elements (REE) are at the core of numerous advanced applications due to their various uses in high strength permanent magnets, lasers, automotive catalytic converters, fiber optics/superconductors, and electronic devices (as phosphors in TVs and display screens for computers and cell phones). Because of the ongoing development of new technologies, there is an increased demand for REE in the international market, with emphasis on identifying new resources to insure an adequate supply for present and future use. World production of rare earths is dominated by China, the United States and Australia; however, in terms of resources, China dominates the world potential with reserves estimated to be over 90% of the total (Chen, 2011).The main commercially significant REE sources, as reviewed by O’Driscoll (1991) are bastnasite (carbonate) and monazite (phosphate) minerals, containing up to 70% wt. rare earth oxides (REO). In spite of being high grade, these ores are associated with elevated recovery costs due to difficulty in mining, separation and beneficiation. Moreover, aggressive conditions are required to solubilize the REE from the mineral, such as leaching with hot, concentrated acids or baking in 70% NaOH (Gupta & Krishnamurti, 2005)."

Jan 1, 2012