Search Documents

By M. B. Shongwe, R. K. K. Mbaya, C. K. Thubakgale, P. Mendonidis

"A low-grade nickel-bearing ore was pre-concentrated on a SB40 laboratory model Falcon Concentrator. Three size fractions, -212+125, -125+75 and -75 µm were tested with the intent to upgrade the nickel content by reducing their content of fine silica, which becomes amorphous during leaching. Separation of silica from nickel-bearing magnesium silicate minerals; hornblende, clinochlore and talc, was more efficient in the finer particle sizes, -125+75 and -75 µm, and at high G-forces. For these two size fractions, nickel was upgraded from 0.06 to 0.07%, with a reduction in silica content from 52.12 to 50.71%. Leaching of feed samples prior to pre-concentration resulted in the formation of amorphous silica, indicative of the presence of fine silica in the samples. Leaching of nickel from the -125+75 µm fraction increased with increasing G-force and feed pulp percent solids, while that of -75 µm was not influenced. The optimum nickel recovery was 15.68% to the Falcon underflow, using the feed size fraction of -75 µm, 30 G and a feed pulp solids content of 10% solids, after 120 minutes of treatment.INTRODUCTION A low-grade South African nickel-bearing ore with about 0.06% Ni was previously studied for atmospheric pressure acid leaching using sulphuric acid. The study was motivated by the continuing search for methods to treat of low-grade ores, which appear to be an increasingly important source of valuable metals as a result of a declining production from rich sulphide ores. Nickel is a base metal that is used as an alloy in steelmaking and chemical industries because of its resistance to corrosion (Haudet et al., 2015). Nickel laterite ores with grades lower than 1.50% Ni are considered to be complex ores, accounting for 70% of the global nickel reserves (MacCarthy et al., 2016). Their complex nature may be attributed to the indefinite mineralogy of these ores, in which nickel may occur in more than one mineral host. In some cases, nickel may be finely disseminated in the ore. The grade of such an ore and complex mineralogy do not justify the application of pyrometallurgical methods for extraction of nickel (Zhu et al., 2012). This suggests that there is a need for less expensive alternative methods of extraction. This study investigates the application of centrifugal gravity concentration, using the Falcon concentrator, followed by leaching to determine the effect of pre-concentration of the ore prior to extraction by atmospheric pressure leaching with sulphuric acid."

Jan 1, 2017

By P. E. Cavanagh

Introduction A comprehensive study of the economics of processes for smelting iron ores has been made by the Ontario Research Foundation on behalf of the Ontario Research Commission. This survey has included investigations of all processes in commercial use, and proposed processes which are still in the experimental stage. The two main objects of this work were to discover (l) whether any known processes would be particularly suited to present and future Canadian conditions, and (2) whether any new process would be of assistance in solving the present scrap shortage in Canada. The future prospects of the Canadian iron smelting industry have changed radically in the past ten years. For nearly twenty years before 1939 no iron ore was mined in Canada. The ore used was imported, mainly from the United States and Newfoundland. The economics of iron blast-furnace smelting always force the location of blast furnaces near the source of coal for making high-grade metallurgical coke, and near the market for iron and steel, rather than near the iron ore. Blast-furnace installations in Canada are confined to the north shores of the Great Lakes with ready access to United States coal and ore and the major Canadian markets, and to Nova Scotia near the coalfields of that Province. This distribution of primary smelting capacity naturally results in relatively high prices for iron and steel in the West, the North, and in Quebec.

Jan 1, 1948

By Greg Baiden

Telerobotics focused on mining is currently being introduced into production systems around the world. Mining companies in Canada, Sweden, South Africa and Australia have tended to lead the international charge to this form of technology for mining. While this introduction is taking place a few basic questions have yet to be answered. How many machines can a single operator run? How many types of machines can a single operator run? A new Canadian Research Chair in Robotics and Mine Automation has been established at Laurentian University. This chair will investigate these questions and many more through a series of experiments in a newly established telerobotics laboratory that connects Laurentian teleoperation workstations to model mining machines at Cambrian college?s eDome. The laboratory will support many experiments allowing researchers to physically run multiple robot scenarios differing the numbers and types of machines at one/quarter scale. Further experiments are being designed to investigate the potential for managing time delays in telerobotics. This paper describes the laboratory, experiments and some preliminary results.

May 1, 2003

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By G. Herget

"A brief visit to European longwall mining operations in potash showed that retreating longwall mining provides a very attractive alternative to room-and pillar mining, especially in areas with bad roof, narrow seams and areas with high ground pressures. Mines de Potasse d'Alsace, France converted all potash operations to longwall mining in 1980. Recovery rates per panel vary between 75o/~ to 85% which compares very favourably with Saskatchewan values. Ground pressure in Saskatchewan are comparable to those of some of the deposits in Europe, but the presence of water in the hanging wall of Saskatchewan orebodies has to be given serious consideration. However, given the mining experience in Saskatchewan and the improved technology f or laboratory and field investigations, a review of present mining practice in Saskatchewan is desirable. IntroductionLongwall mining is practiced widely in coal mining and allows complete mechanization. It is applicable at great mining depth, in thin seams, weak roof and has been applied recently even to coal bed s dipping more than 65 degrees. Ideally this system allows complete extraction of an orebody. However, with high mechanization and emphasis on obtaining high outputs per man shift, extraction ratios rarely reach more than 80010 per panel.France, Spain and the U.S.S.R. have had longwall operations in potash for some time and a brief description is given below. Two of the operations were visited and the Russian operation is described based on German literature"

Jan 1, 1986

By M. A. Perras, H. A. Kasani, G. Walton

The development of an underground repository for the storage of spent nuclear fuel relies on a multi-barrier system to isolate the used fuel from the environment – ultimately, the biosphere. These barriers include engineered copper and steal canisters, dense bentonite, and the natural rock as well. In order to reduce the potential flow pathway along the excavation induced damage zone, various slots perpendicular to the excavation axis have been proposed. These slots are called cut-off seals and generally are filled with bentonite as it has high swelling potential and very low permeability. Many different geometries have been proposed, but clear guidelines on the selection of the optimum geometry have yet to be developed. In order to assess the optimum geometry, three shapes have been selected for this numerical study, including a trapezoid, a triangle, and a thin rectangular slot. The cut-offs were modelled for a conceptual shaft constructed in the Queenston Formation from Ontario over a stress to strength ratio that has been found at many underground research laboratories. It was found that the excavation of a triangular and thin slot cut-off had the smallest increase in the damage as quantified based on the extensile volumetric strain within the plastic yield zone. Both shapes showed an increase in the damaged zone by 13 cm at a stress to strength ratio of 2.75. The trapezoidal cut-off damage zone increased by 20 cm at the same stress to strength ratio. Further study is required to better define the optimum cut-off shape for wider variety of conditions and other geological formations.

Jan 1, 2020

By S. A. R. Keneti

Predicting the geomechanical response of the shale gas material during hydraulic fracturing operation in the field needs better understanding of their geomechanical behaviour under laboratory testing. Anisotropy is considered as a critical factor during investigation and analysis of deviated boreholes, borehole stability, stress-strain and strength behaviour, generation and propagation of fracture and fluid flow. In this study, compressive elastic modulus (Ec) of the Montney shale has been investigated in two perpendicular directions: unconfined compressive strengths test was conducted on the Montney sample to measure its Ec in the vertical direction. This value then was compared to the Ec value in the horizontal plane (i.e. foliation plane) which was previously measured throughout a Brazilian test by Keneti and Wong (2011). From the results, the representative values of Ec in the vertical and in the horizontal directions were found as 25 GPa and 40 GPa, respectively. Computer tomography technique was also employed for the experimental data interpretation.

Jun 1, 2012

By M. B. Kime, E. K. Kanowa

"Heap leaching of low-grade copper-cobalt oxidized ore and solvent extraction of copper, cobalt, manganese, and zinc were investigated. Heap-leaching parameters were optimized using agitated and tray batch leaching tests, capped by tests on a pilot semicontinuous heap-leach plant. The optimum pregnant leach solution yielded 2,350 mg/L Cu, 3,800 mg/L Co, 3,600 mg/L Fe, 130 mg/L Mn, 25 mg/L Zn, and 0.58 g/L solids in suspension, with pH and acidity of 1.27 and 3.66 g/L, respectively. Copper, cobalt, and impurities (Mn and Zn) were extracted using (v/v) 30% CP-150, 20% IONQUEST® 290, and 20% D2EHPA, respectively; overall recoveries of copper, cobalt, and impurities were 98, 99, and 70%, respectively.RÉSUMÉ La lixiviation en tas des minerais oxydés de cuivre et de cobalt et l’extraction par solvant du cuivre, du cobalt, du manganèse et du zinc ont été étudiés. Les paramètres de lixiviation en tas ont été optimisés à l’aide d’essais de lixiviation en discontinu sur un plateau, complétés par des essais relatifs à une usine pilote de lixiviation en tas en semi-continu. La liqueur-mère optimale a produit 2 350 mg/L de Cu, 3 800 mg/L de Co, 3 600 mg/L de Fe, 130 mg/L de Mn, 25 mg/L de Zn et 0,58 g/L de solides en suspension, avec un pH et une acidité respectifs de 1,27 et 3,66 g/L. Le cuivre, le cobalt et les impuretés (Mn et Zn) ont été extraits avec un pourcentage volumique (v/v) de 30 % de CP-150, de 20 % d’IONQUEST ® 290 et de 20 % de D2EHPA, respectivement. Les récupérations totales de cuivre, de cobalt et d’impuretés étaient de 98 %, 99 % et 70 % respectivement.INTRODUCTIONBoss Mining S.P.R.L. is a privately owned hydrometallurgical plant located in southeastern Democratic Republic of Congo. It treats oxidized ores of copper and cobalt that are recovered by sulphuric acid heap leaching (Trujillo, Cisternas, Gálvez, & Mellado, 2014; Kime, Kanowa, Mulaba- Bafubiandi, & Diyambi, 2016) and solvent extraction processes (Crane, Urbani, Dudley, Horner, & Virnig, 2009; Fisher, 2011; Kime et al., 2016). The ore to the plant is primarily sourced from the Luita and Mukondo mines. Geological prospecting work by Gecamines and Boss Mining showed that the Mukondo mine contains a very large cobalt reserve not yet exploited, but with grades as low as 0.2%.Currently, Boss Mining is focusing on the production of copper, but is investigating methods to efficiently produce both copper and cobalt. A challenge in the production of cobalt from this ore is its presence in the third oxidation state. This requires the addition of reducing agents, which increases the overall operating cost (Kime & Makgoale, 2016). Cobalt solvent extraction is also very sensitive to impurities such as nickel, zinc, manganese, and aluminum, which are often co-extracted (Swartz, Donegan, & Amos, 2009). This sensitivity to impurities requires the optimization of operational parameters to lower impurity levels as much as possible in the electrolyte."

Jan 1, 2017

By Bern Klein, Tichang Sun, Daozhen Gong, University of Science and Technology Beijing, Chunbao Sun, Stefan Nadolski

"This paper is focused on the effect of modifying the SAG mill/ball mill transfer size on the energy efficiency of SABC circuits. The transfer size is considered to be a parameter which provides operators with the opportunity to improve comminution circuit performance. In this study, the Moly-Cop tools package was employed to predict the energy consumption of SAG mill and ball mill circuits under different operating conditions. An Energy Benchmarking model was adopted to calculate grinding energy efficiency. The SABC circuit at the Huckleberry mine was selected for this case study. It was observed that after increasing circuit transfer size (T80) from the existing 3.3 mm to 4.8 mm, the Benchmark Energy Factor (BEF) of the SABC circuit decreased from 4.30 to 4.05. In terms of energy consumption of the SABC circuit, 1.17 kWh/t of specific energy saving was achieved through the transfer size optimization.It was also observed that when a transfer size was selected such that both SAG mill and ball mill circuits operated at their highest energy efficient states, the entire SABC circuit was the most energy efficient. The maximum energy efficiencies of these three circuits were all approximately 25% when compared to the minimum practical energy required to carry out an equivalent comminution duty. Single-particle compression breakage testing was used to determine the minimum practical energy associated with the Huckleberry mill feed. In combination with geo-metallurgical data, this study also provides an opportunity to perform dynamic optimization of SABC circuits."

Jan 1, 2016

By M. J. Davie, D. S. Ross

"The successful design of a new mine water pumping system is in part dependent upon the accuracy with which the operating conditions can be forecast. This paper outlines the data which should be obtained on water quantity and quality. Methods of modifying the quality are also discussed. Some pumping systems for disposal of sludge are described, citing operating examples. The various types of mine dewatering pumps are described in terms of design characteristics as they affect operating efficiency and installation and maintenance costs. Piping system parameters are outlined. Finally, a hypothetical case study of pumping from a depth of 3,000 ft is assessed, with particular reference to capital costs.IntroductionMany mine operators would agree that the pumping system usually receives a low engineering priority during the design stage, and as a consequence causes some of the most frustrating problems during production. For a ""dry"" mine (up to 200 gpm), design of the pumping system may indeed be simple, but outside of the potash industry such mines are not common. For ""wet"" mines, the pumping system is important because it significantly affects the initial capital and on-going energy costs of the mine and, in the area of sludge disposal, the working conditions and production costs. Indeed, a failure in the pumping system usually has serious, and sometimes disastrous, consequences.The intent of this paper is to outline the factors which should be considered in the design of a pumping system and to describe the types of pumps used in mine dewatering and relate them to practical operating systems."

Jan 1, 1980

By J. Walker, G. E. Kim

Since May of 2000, Mogas Industries, in partnership with F.W. Gartner Thermal Spraying Co. and using the services of Perpetual Technologies, has invested time, energy, and resources towards developing novel ball valves for high-pressure acid-leach (HPAL) service. In addition to developing new valve designs, an aggressive coatings development effort has been undertaken to improve the protective quality of the coatings so as to enhance the performance and extend the life of valves in severe HPAL conditions. In 2001, Mogas Industries qualified and applied a nanostructured titanium oxide (n-TiO2) coating for gold and nickel/cobalt HPAL services. The n-TiO2 coating provided dramatically superior protection against abrasive and erosive wear, fared very well against high-pressure autoclave corrosion testing, and has performed well in HPAL service.

Jan 1, 2004

By A. Luszczkiewicz

This paper presents the beneficial effects of non-oxidative leaching of final and intermediate copper sulfide concentrates with sulfuric acid prior to the final cleaning stage of flotation. This unique process, combining leaching and flotation, appears to be advantageous for difficult-to-treat carbonate-bearing Polish copper ores, such as those processed in copper concentrators at KGHM Polish Copper. It was shown that after the chemical decomposition of about 70 % of the total carbonates naturally present in the flotation feed, a considerable enhancement of subsequent flotation results (both grade and recovery). The resulting products of non-oxidative leaching are solid hydrated calcium sulfate (gypsum), soluble magnesium sulfate and gaseous carbon dioxide. The beneficial effect established by the laboratory leaching tests was subsequently confirmed during a pilot plant operation treating final copper concentrate and a problematic intermediate concentrate at the Lubin concentrator.

Jan 1, 2007

"IntroductionThe Chairman, in his speech to this body last year in Montreal, stated that the Dominion Coal Board looked to and depended upon the Bureau of Statistics for statistical material, and the Bureau does collect and publish monthly and annual data on coal. It may therefore be asked why an officer of the Dominion Coal Board should prepare and give a talk on statistics.I would explain that it has been our experience in the Board that, since the supply and consumption of coal in Canada is subject to a seasonal ebb and flow, it can be more profitably studied on the basis of a twelve-month period ending on March 31st than of a calendar year, since the end of March does represent a fairly stable end point in this ebb and flow. The figures are not prepared or published by the Bureau on that basis and it has therefore been thought that a presentation on this fiscal-year period would be of interest. The Bureau of Statistics has agreed that this may be valuable and all the data here presented are based on the reports secured from various sources by the Mining, Metallurgical and Chemical Division, Dominion Bureau of Statistics. The only contribution by either myself or the staff of the Dominion Coal Board has been the tabulation in a different twelve month period, and the comments upon the picture presented.It should be noted that the data for the month of March, 1950, are not available in all cases and consequently the figures for that year contain an estimate for this month."

Jan 1, 1950

"Option pricing is used in finance for valuing options to buy (or sell) shares at some future date because it provides a convenient framework for quantifying values subject to uncertainty. As one of the main sources of uncertainty in mining is the price (sales) of the metal, this approach can also be used for valuing mining projects.The first part of this paper reviews options and option pricing; the second part presents the approach developed by Brennan and Schwartz (1985) for using option pricing to value natural resources. Several applications of this methodology have been published; these are described. From a mining point of view, the assumptions made by Brennan and Schwartz are too simplistic. The weaknesses are discussed with a view to improving an apparently promising new way of assessing the value of projects. IntroductionThe collapse of the British merchant banking group, Barings, has highlighted the risks that can be incurred by speculators and arbitragers in the futures and options markets. But this negative attention on futures and options should not make us forget their positive aspects. They can provide producers and consumers of metals with more predictable sales prices. The introduction of the new traded average price options, TAPOS, by the London Metal Exchange in January 1997 is a response to this need. Equally important, the theory that the finance industry has developed for valuing options provides an interesting framework for valuing mineral projects as well. While this paper was being revised, the South African gold mining house, JCI, announced that it was using a methodology based on option pricing for valuing the mineral rights to deeplevel gold resources (see Box 1)."

Jan 1, 1997

By W. D. Sinclair, R. J. Cathro, E. M. Jensen

"The Cash is one of the largest porphyry copper-molybdenum Deposits found in Yukon to date. It is 80 km northwest of Carmacks, within the unglaciated portion of the Dawson Range, and is associated with the Big Creek fault, an important tectonic feature. Part of the mineralized zone is blanketed by up to 70 m of alluvial drift . The remainder is covered by a relatively thin residual soil layer. The mineralized zone, however, was not detected by conventional stream-sediment sampling because pathfinder elements, such as Cu and Mo, have not been geochemically dispersed into the main drainage system. The deposit was discovered by a combination of soil analysis and inspection of rock fragments from small pits.Twenty widely spaced, shallow drill holes have outlined an areaover 2700 m long and 550 to over 1000m wide that grades more than 0.1% copper equivalent (% CuE = % Cu + (5 x % MoS2)). Two smaller zones grading over 0.4% copper equivalent occur within the larger area. The limits of the widest end of the deposit have not been delineated.The Cash deposit is fairly typical of high-level, calc-alkaline porphyry copper-molydenum occurrrences in the Canadian Cordillera {cf, CIM Special Volume 15) and is representative of most prospects in the Dawson Range. It is associated genetically with a subvolcanic complex of small, irregular stocks and dykes of feldspar porphyry and related breccias of Late Cretaceous age. Copper and molybdenum sulphides occur along fractures, in quartz veinlets and disseminated in feldspar porphyry and in older metasedimentary and intrusive rocks. Higher-grade zones of copper and molybdenum have associated potassic alteration. Phyllic alteration is, in part, superimposed on potassic alteration. Argillic alteration occurs locally.This paper describes the history of the discovery and the geochemical and geophysical characteristics, together .with the regional geology, and the nature and distribution of the host rocks, hypogene mineralization and hydrothermal alteration."

Jan 1, 1981

By D. J. McCulla

Mineral development and utilization affect the health of the economy and the pattern of long-term development throughout Canada. There are many diverse opinions on the contribution of minerals to the economy, but there is a dearth of adequate quantitative information. This paper discusses some recent research and provides some new information.

Jan 1, 1977

By Jean Scott, G. A. Collins, G. W. Hodgson

WHILE it is well known that trace metals in crude •oils and distillates have been a matter of deep concern to refining engineers because of the damage done .by the metals to cracking catalysts and refractories (8, 5), the trace metals in crude oils may be of great benefit in correlation studies and in origin studies. During the geological processes in which the oil is formed from •animal and vegetable life, the hydrocarbons are subjected to a host of inter-related reactions, both physical and chemical. It has been well demonstrated that the lighter materials, certainly the short-chain paraffin hydrocarbons, are degradation products of the heavier molecules, and it might be concluded that for correlation studies it would be advisable to direct attention as much as possible not to the degradation products of the large molecules but to the large molecules themselves. Be this as it may, the methods at •hand to conduct the study are not particularly precise and, in the past, attention has centred on the simpler small molecules, as evidenced by the great mass of work involving distillation and chromatography with painstaking separation of the simpler 'front-end' hydrocarbons.

Jan 1, 1954

By C. I. Godwin

"The relative-value (R-value), discrimination-factor (D-factor), and vector-ratio (V-ratio) method (RDVM) provides a geological knowledge-based statistical and geological-genetic interpretation scheme for geochemical data that enhances discovery in geochemical exploration. The practical advantage of RDVM is that it synthesizes geochemical features geologically related to ore-deposit discovery in three steps: reclassifying element concentrations using log-probability plots into R-values; calculating geologically defined D-factors from R-values; and determining V-ratios. D-factors are the sum of R-values, divided by the number of R-values summed. Based on the analyses selected, D-factors mimic rock or mineral deposit signatures. V-ratios refine interpretations of rock type and vector to orebody locations.RÉSUMÉ La méthode de la valeur relative (valeur R), du facteur de discrimination (facteur D) et du rapport de vecteurs (rapport V) (RDVM), fournit un schéma d’interprétation des données géochimiques basé sur les statistiques et les connaissances géologiques et la génétique géologique; ce schéma contribue aux découvertes en exploration géochimique. L’avantage pratique de la RDVM est qu’elle fait la synthèse des caractéristiques géochimiques reliées géologiquement à des découvertes de gisements de minerais en trois étapes : une reclassification des concentrations des éléments au moyen de courbes de probabilité logarithmique en valeurs R; un calcul des facteurs D définis géologiquement à partir des valeurs R et la détermination des rapports V. Les facteurs D sont la somme des valeurs R divisés par le nombre de valeurs R additionnées. Selon les analyses choisies, les facteurs D imitent les signatures de la roche ou des gisements minéraux. Les rapports V peaufinent les interprétations des types de roches et dirigent vers des emplacements de gisements."

Jan 1, 2016

By J. I. Gazzarri

A model of solid oxide fuel cell AC impedance behaviour has been developed and is used to simulate the frequency response of a single cell with and without mechanical damage. The results indicate that the presence of mechanically induced damage within the components of a solid oxide fuel cell can be detected by comparing the frequency response of the undamaged cell with that of a cell in which in-plane cracking or delamination has occurred. The presence of such defects manifests itself as a new semicircle in the Nyquist impedance diagram of the full cell. A parametric study reveals the resolution capabilities of the method in terms of the geometrical characteristics of the defects.

Jan 1, 2005

By L. S. Beck

"The Athabasca region forms part of the Churchill province of the Canadian Shield and is underlain by an Archean or Aphebian assemblage of rocks that underwent severe metamorphism and granitization during the Hudsonian orogeny (1750-1950 m.y. ago). In places, the eroded orogen is overlain by unmetamorphosed cover rocks (in-cluding the Martin and Athabasca formations) of probable Paleohelikian age. Basic dykes cut all the rocks of the region.There are innumerable vein-type pitchblende deposits and many syngenetic occurrences of uraninite in crystalline basement rocks. Evidence is presented to show that pitch-blende was emplaced during the final stages of the Hud-sonian granitization and followed the crystallization of syngenetic uraninite transitionally. In terms of P-T condi-tions, the pitchblende deposits belong essentially to Lindgren's mesothermal group.Based on the postulated uranium metallogenesis, the possibilities of finding further deposits of pitchblende and other types of uranium deposits are discussed."

Jan 1, 1970