Search Documents

By K. Bruce Hodgins

The North American mining industry faces challenging emissions regulations in coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable. Westport Innovations Inc., of Vancouver B.C. has developed high pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications, reduced emissions of NOx, PM, and CO2, with no loss in performance. This is accomplished through late-cycle high-pressure injection of natural gas directly into a diesel engine combustion chamber. The natural gas is injected at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the main natural gas fuel injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, low speed torque, high-power output, no engine knock and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored in a similar manner and volume to diesel fuel by virtue of its increased energy density over compressed natural gas. Cummins, Inc. of Columbus, Indiana and Westport have formed a joint venture, Cummins Westport Inc. (CWI), under which agreement the HPDI technology is being applied to a Cummins QSK engine series for high horsepower applications such as mine haul trucking. CWI, along with Komatsu Mining Systems, ENRG Fuels, Placer Dome, and Cortez Joint Venture are performing a feasibility study for the development and demonstration of an LNGfueled HPDI QSK engine in a large mine haul truck. The goal would be to demonstrate low emissions consistent with EPA ?Blue Sky? standards, high efficiency based on HPDI technology and good economics resulting from the high fuel consumption of 2,000+ hp trucks.

May 1, 2002

By F. G. Pickard

"The Strathcona Concentrator is one of three concentrators presently operated in the Sudbury District by the Nickel Division of Falconbridge Nickel Mines Limited. Production commenced in 1968 at a milling rate of 6,300 tons per operating day. Milling capacity was increased in 1970 to 7,200 tons per operating day. 7he ore contains iron, nickel and copper primarily in the form of pyrrhotite, pentlandite and chalcopyrite, while the common gangue minerals are feldspar, quartz, mica, talc and chlorite. The primary function of the concentrators is not only to liberate sulphides from silicate gangue minerals but also to separate pyrrhotite from the more valuable minerals pentlandite and chalcopyrite.SummaryExcessive wear on steel liners and blinding of grates in a regrind pebble mill of the Hardy Concentrator was corrected by the use of rubber liners and grates. The success of these resulted in their installation as original linings In all grinding units except the rod mills at the Strathcona Concentrator. The operation of rubber liners and grates when sized mine ore was used as the grinding medium was satisfactory confirming the Hardy Concentrator experience. Problems developed when the grinding medium was changed from sized mine ore to steel balls in that blinding of the grates occurred. This resulted in conversion of the units to overflow type mills through removal of the grates. The lifter bar life was significantly increased by using higher lifter bars.Grinding PracticeOperation of a regrind pebble mill commenced in 1961 in the Hardy Concentrator. This operation demonstrated the economic feasibility of using sized mine ore as grinding medium. Problems caused by excessive wear of metal liners and grates combined with blinding of the grates were corrected in 1964 through installation of rubber liners and grates."

Jan 1, 1974

By J. Wong, M. G. Lipsett, L. K. Daneshmend

"Current trends of increased size, complexity, and automation of surface mining equipment necessitate more comprehensive and objective techniques for equipment comparison and selection. The field of reliability analysis provides tools to generate quantitative bases for maintenance and reliability aspects of such comparisons. Results from statistical analyses of failure and repair time data are used to perform the comparison. A case study is presented which analyzes five machines of two different technologies and three different designs.IntroductionThe surface mining industry is currently faced with a rapid evolution in production equipment. The more obvious trend in this evolution is the steady introduction of even larger machines. Parallel, and complementary, to this increase in size is the introduction or adaptation of new technologies. Together, these two trends result in new surface mining equipment designs; these designs are often more complex and may feature technologies that have yet to be proven for the application or at the scale they are now fielded.The prospect of significant automation of open pit equipment is also bound to add complexity to future equipment designs. Semi-automated features, such as drilling controllers (Aquila, 2000), have already been commercialized. Fully autonomous haul trucks have been demonstrated in open pit mines (Jackson and Zoschke, 2000). Design concepts for comprehensive teleoperation of open pit operations have been formulated (Lipsett, 1998).With this rapid availability and deployment of new technology and equipment, managers and maintainers are faced with a multitude of decisions regarding what equipment to acquire and what maintenance strategies to implement. In light of this evolution in mining equipment, it is necessary to develop better methods for making equipment management decisions (Dessureault et al., 1999; Paraszczak, 1999). The incentive for development of such techniques is that a large portion of an open pit mine’s operating cost is maintenance related, as shown in Table 1."

Jan 1, 2000

Material scheduling, sequencing planning and execution are the core tactical mine plan for achieving production targets that maximize the objective function of any mine production entity. This objective function is constrained by several exogenous and endogenous constraints including geological, operating, technological, marketing, financial, political, social and local field constraints. Linear and dynamic programming techniques have been used to formulate algorithms to solve the problems associated with scheduling and sequencing operations. These algorithms possess the mathematical rigor for dealing with the fundamental problems but they fail to provide adequate answers to random and dynamic process problems. Materials scheduling and sequencing are carried out within the bounds of random and dynamic fields. The functional relations between the output and dependent variables are random, and thus, current algorithms are limited in their abilities to address the problems arising from these random field processes. In this study a production simulator is developed to capture the random field process associated with materials scheduling and sequencing in an open pit environment. The algorithm incorporates a geometric pit evolution model, using solid geometry of an ellipsoidal frustum to capture material displacement dynamics. Taylor series expansion about the dimensions of the initial frustum is used to provide numerical solutions to the resulting partial differential equations governing the pushback dynamics. A production simulator, derived from the stochastic and dynamic models, is developed, validated and used to simulate the changes in the pit volume resulting from periodic incremental pushbacks and the random field process. The hybrid stochastic-optimization algorithm provides a powerful tool for addressing the random field and dynamic process problems. Combined with a hybrid stochastic-optimization dispatch system, tactical production planning and execution will be efficient and economic for achieving desired.

May 1, 2004

By Rick Moignard

Relationships between Information Technology providers and their clients are often segmented according to job specific tasks. As a consequence, technology providers tend to focus on automating repetition and complexity, resulting in software that improves individual productivity while failing to address the interdependency of mining functions. For this reason, technology vendors like Gemcom are following partnership approaches with their clients, engaging corporate and operational stakeholders to better understand mining business objectives. This presentation examines some of the approaches that help foster the development of solutions that leverage the information produced during mine operations to improve downstream process control and tactical decision support.

May 1, 2006

By Linda Duncan, Trevor Yeomans, Chris Potorieko, Michael Fullam

"NVI Mining’s Myra Falls Operation is a 4,000 mtpd copper/zinc flotation circuit with by product gold of ~28,000 ounces per year. Gold recovery has historically averaged 40-55%, however, a portion of this was recovered in the zinc concentrate and received poor payment. Two Knelson CD-30 Concentrators have been operating in the grinding circuit since 1992, with gravity recovery averaging about 2-5% over that time period.The Myra Falls gravity circuit was one of the very first hard rock mining installations operating in the world with automated Knelsons. The mine has employed a unique and unusual upgrading method for the Knelson concentrate that had never been evaluated as to its efficiency. Recent Gravity Recoverable Gold Testing by McGill University, and mathematical modelling of the Gravity Circuit by Knelson Gravity Solutions indicated the gravity circuit was not living up to its potential. Myra Falls Personnel changed the upgrade system-operating regime, and a complete gravity audit of the grinding circuit was carried out, with the results confirming the initial suspicions. Gravity recovery increased from 5% to 15%, with overall gold recovery improving by 5%.INTRODUCTIONNVI Mining operates a 4000 tpd mine and mill complex on Vancouver Island. The milling circuit consists of open circuit rod milling, closed circuit ball milling, gravity recovery, copper flotation, zinc flotation, and tails disposal. There are two milling circuits, “A” circuit, and “B” circuit."

Jan 1, 2006

By C. Carlson, W. Muir

"The oxygen demand of the complex lead-zinc-iron feed at the Cyuro Anvil concentrator was determined denendent on the cyanide ion con-contration of the pulp. By redistribution of the cyanide [ ] the grinding circuit in direct proportion to the amount of surface area created, a more activated flotation feed in obtained.Monitoring the oxygen demand of the flotation feed and grinding mill discharge has proved useful in diagnosing metallurgical problems day to day operation."

Jan 1, 1976

By Lloyd Buckingham

Barrick Gold Corporation (Barrick) has undertaken innovative methods of evaluating and improving the performance of grinding mills in several of its operations around the world. The results have been positive with some of the mines showing more than 20% net energy improvement leading to more than 43,000 tonnes per year reduction in CO2 emissions in four of the operations reviewed.

Jan 1, 2012

By Richard Jundis

At the Vale Inco Ontario Operations, the working environment is rapidly evolving with organizational changes, new business systems and software tools. These changes are required in order to meet today?s challenging business environment. Mining professionals are focusing on the development of safe and achievable mine plans to maximize mining value while reducing the potential of project delays and production shortfalls. This paper explores how new design tools, techniques and system designs in mine planning are being developed to optimize the value of every ton of ore mined and processed. To differentiate from other papers on long-term planning, this paper focuses on the concept of business planning at the mines. Business planning is the understanding and optimization of the relationship between mine plans and the value it adds in the overall process. The management and key stakeholders of Vale Inco have recognized that the development of a robust mine planning system and programs are essential for the long-term sustainability of the operations.

May 1, 2009

By W. G. Johnson

"As we move into 1983, Canada is not only in a deep recession, there are major changes taking place.International competition is growing fiercer.Major core industries such as automobile, steel, mining, oil, agriculture, forestry, fishing, major manufacturing and others are just not expanding.If and when recovery comes starting in mid-1983, as many predict, don't expect industries to suddenly resume former growth patterns. It's just not possible.Companies, by necessity, are becoming lean and mean, and they are still in the process of reducing staff to meet changing times and conditions. Many of the staff now being released may never return to fulltime work with a single employer, particularly if they cannot measure up to more exacting performance standards and management expectations.There are clear cut instances of people who lose a job for reasons beyond their control. A merger, the loss of function, or a major reorganization sometimes creates casualties of people who were excellent performers. Such people can survive well, based on the tongue of good report and with some help from associates or others. However, even good performers often have difficulty in adjusting to the rigors of finding a new job and to become their own personal salesman."

Jan 1, 1983

By John G. Kelly

"In 1982 an extensive study was carried out to determine the best means of size reduction for the ore to be hoisted through the borehole hoisting system at Sherritt Gordon's Fox Mine.The study examined three alternatives:1. a jaw crusher,2. pneumatic rockbreaker(s) at a grizzly, and3. hydraulic rockbreaker(s) at a grizzly.The final decision was a compromise between alternatives 2 and 3. Two rockbreakers, one pneumatic and one hydraulic, were installed over a single grizzly. Some modifications have been made to the system, but over-all it has operated at acceptable levels since its installation in July 1983.As all the ore passes through a jaw crusher before being hoisted to surface, an evaluation of the relative performance and cost-effectiveness of the jaw crusher and the two types of rockbreakers is possible. This paper outlines the initial study, and compares the three breaking systems in operation at Fox Mine.IntroductionThe Fox Mine of Sherritt Gordon Mines Ltd. is located 800 kilometres north of Winnipeg near Lynn Lake in Northern Manitoba. Production at the copper-zinc orebody began in 1970 at a rate of 3,000 tons per day. Over 12.5 million tons will have been hoisted from the underground mine when the ore reserves are depleted in October 1985.The mining method at Fox Mine is sub-level open stoping with delayed backfilling are from the upper level stopes, above the 2000 level, is mucked on the main levels established at 400-ft elevation intervals, and is fed through a central orepass to the crusher located on 2100 level. Production in the lower levels commenced in 1975, and ore from the 2200 and 2400 level stopes was hauled up a 15010 ramp by 26-ton trucks to the 2000 level orepass dump. Projected production rates from the 2600 and 2800 levels using the trucking system were too low, and therefore, in 1983 a borehole hoisting system was commissioned to hoist that ore'!'. One thousand tons per day of ore are skipped through an 8-ft diameter borehole from the 2650 level loading pocket and dumped on the 2000 level. The ore is transferred by LHD to the main orepass for crushing before being conveyed to the main shaft for hoisting to surface (Fig. 1)."

Jan 1, 1986

By Manqiu Xu, Peter Wells, Gord Bacon

"A methodology is proposed for milling flowsheet design using flotation rate, selectivity and residence time distribution data. The flotation rate data and the difference in flotation rates between the main minerals to be separated are determined from laboratory batch tests. The residence time distribution (RTD) data is calculated using the tanks-in-series model assuming each flotation cell is a perfect reactor. The rate, selectivity and RTD data can be used to calculate the optimum flotation cell number in a bank for rougher/scavenger in a commercial plant.This methodology is demonstrated in a case study of a nickel sulfide ore. It is shown that miniplant rougher/scavenger data can be closely predicted from a batch test using the proposed methodology.INTRODUCTIONIt has been the trend in the past several decades that large flotation cells are increasingly used. This is largely driven by the economics as ore grades are getting lower and the rate of ore processing must be increased in order to keep mining operations economically viable. The development and evaluation of 250 to 500 m3 WEMCO SmartCell and Outokumpu TankCell flotation machines are well in progress. There are many advantages in using large cells: fewer cells, less floor space, lower power cost (although this is now being questioned for fine particle flotation), simpler circuit, simpler control, and lower auxiliary equipment cost (Arbiter, 1999). As flotation cells are getting larger, the importance of cell hydrodynamics, namely, air/slurry dispersion, power intensity, froth transfer, residence time distribution (RTD) and short-circuiting are being fully recognized (Jonaitis, 1999; Weber, et al., 1999; Gomez and Finch, 2002). It is not the intention of this paper to discuss flotation cell scale-up. The intention is to answer what is the optimum number and size of cells in a flotation bank for a given throughput. Figure 1 illustrates this problem facing design engineers. The same mean residence time required for a given throughput can be achieved in a single large cell, or many smaller cells in a row. A few cells of large size may be more cost-effective but they may not be as effective as more cells of smaller size in achieving the optimum metallurgy."

Jan 1, 2005

By Francis Chartrand

The Kwyjibo deposit is an iron oxide Cu-REE-F-Mo-Au mineralization of Mesoproterozoic age located in the Grenville Province approximately 120 km NE of Sept-Îles, Quebec (Figure 1). Occurring along the SE margin of the Canatiche granitic complex, the deposit is composed of several polymetallic showings that are related to different textural facies of magnetite. The mineralization process at Kwyjibo is complex, and is divided into Early Granitophile, Magnetite, Main Polymetallic and Specular Hematite stages (Cayer et al., submitted for publication). The Main Polymetallic stage, comprising chalcopyrite, pyrite, fluorite, molybdenite and REE-bearing minerals, is superimposed on pre-existing magnetiterich rocks. Discovered by SOQUEM Inc. in 1993, the Kwyjibo deposit shares many characteristics with other hydrothermal polymetallic iron oxide deposits around the world. Foose and McLelland (1995) suggested that this class of mineralization could occur in the Grenville Province. However, only a few polymetallic occurrences are known to be associated with low-Ti iron oxide deposits in the Grenville. Kwyjibo is one of the most significant examples of a polymetallic iron oxide deposit to have been found in the Grenville Province to-date.

May 1, 2003

By Christian Ottergren

"Modern crushers offer double the capacity and performance of classic models. In some cases crushers are replacing SAG circuits, the advantages being smaller investment and lower operating costs. Is Tertiary crushing replacing SAG milling as the most optimal grinding method? Does tertiary crushing achieve the same outcomes as SAG milling? This paper considers these questions and provides an assessment of the strengths of tertiary crushing in comparison to other methods. Two case studies: a Scandinavian Platinum Project, and CODELCO, are also presented.INTRODUCTIONResearch on basic parameters in crushing started at Chalmers University in 1993. The initial project has developed and now involves several related areas. Modelling in accordance with new theories has resulted in modified designs which have been implemented and shown improved performance at operating mines in Chile. Sandvik Rock Processing is a partner and a major supporter of this program. This paper will cover some of the achievements and give references to the research reports.The mining industry has for many years mainly used crushers of the traditional 7’crusher concept, with thread adjustment of the setting and with a spring or hydraulic overload system. This machine type has been the workhorse for crushing throughout the world. The explanation for the dominance of this machine is that it has a reliable mechanical design. It can be estimated that about 2000 crushers of this design are still at work.Technical development in all fields utilizes new technologies like high-strength materials, advanced control systems and more extensive use of hydraulics. This is the reason why today’s motorcars, for example, are more efficient, more reliable and more environmentally friendly than their predecessors in the 1950s. Crushers are no exception. This paper will cover experience from the latest-generation cone crushers developed by Sandvik Rock Processing.The parts in this paper related to the CODELCO ElTeniente copper mine in Chile are coauthored with responsible personnel from the operation at the mine."

Jan 1, 2004

By M. Tarvainen

"Lately, the development work in closed circuit grinding has mainly been focused on mills and on different types of instrumentation, mathematical models and automation in spite of the fact that the poor efficiency of the classifier is well known. It has also been proven by several investigations that by improving the sharpness of classifier separation, remarkable technical and economical advantages can be achieved. Some attempts to improve the performance of the most common classifier, hydrocyclone, have been made, among them injection of wash water above the spigot cyclone and retreatment of either or both of the products of the primary classifier. No method has been successful enough to achieve general adoption in the industry. The purpose of this paper is to introduce some industrial results achieved by two-stage classification where the coarse product of the turbulent-flow classifier, hydrocyclone, is cleaned in a laminar-flow cone classifier.The main target of the adoption of the two-stage classification circuit it naturally to improve the sharpness of size separation. This again leads to the following advantages in the grinding process:- lower circulating load and increased capacity- lower energy consumptionnarrower size distribution in the fine product- less overgrinding and less slimes- reduced specific surface areaThese improvements, no doubt, reflect on the subsequent concentrating process in the following aspects:the rate of flotation is improved, less reagents and energy is neededthe recovery and grade of valuable minerals in concentrates is improved- savings in dewatering can be expected- less fines in tailings improve the conditions for water recirculation."

Jan 1, 1980

By Roy T. Bowles

This paper focusses on technological developments which occurred in the village of Deloro, Ontario between 1868 and 1919. These developments illustrate the manner in which improved metallurgical processes linked Ontario mineral resources to industrial expansion. Overview of Deloro The village of Deloro is in Hastings county, about 5 miles from the village of Marmora, the site of the old Marmora iron works and the more recent Marmoraton iron mine. In this area, the Canadian Shield meets the Great Lakes lowlands. The first settlement in the vicinity occurred in the 1820s and was associated with the Marmora iron works. Settlement grew around agriculture. Gold was discovered in Hastings county in 1868. Deloro - the name derives from gold - developed as a concentrated settlement in proximity to several gold mines and the related processing activities. By 1901, substantial smelting works were successfully producing gold and arsenic from local ores. The village was developing as a company town within the framework of benevolent paternalism. For reasons associated with markets and with local ore supplies, the Deloro mills were idle for a period beginning in 1902. Developments in later periods connected Deloro to world events. In 1903, silver was discovered at Cobalt, Ontario. By 1907, M.J. O'Brien, who owned mines at Cobalt, had purchased the Deloro works and was using them to process Cobalt-area ores*.

Jan 1, 1999

By Cecilia Arrue, Dominic Fragomeni, N. O. Lotter

"A statistically designed benchmark mill survey was carried out in July 2005 at the Kidd Creek Concentrator, D Division circuit, which processes Ni/Cu ore from the Montcalm deposit. A structured statistical survey approach was followed, together with defined quality controls, which would assign a 95 percent level of confidence in the result.A set of six surveys were completed over a limited time; the corresponding stream samples of the surveys found acceptable were combined to obtain high confidence composite samples. The head grade of each survey is compared to two distributions to test its acceptability; surveys that fail to conform to these trials are rejected. The accepted set of surveys, which is a robust representation of the process, is prepared into a composite for QEM-SEM analysis and mass balance purposes.Where the above practice is a standard procedure in Falconbridge for QEM*SEM purposes, in this case each individual two-hour survey unit was measured and analysed for a mass and value balance. It is shown that none of the individual mass and value balances close as well as the composite set of accepted two-hour survey units. This founding is in keeping with the averaging properties of the Central Limit Theorem.INTRODUCTIONMontcalm OperationsNi/Cu bearing ore from the Montcalm deposit is being processed at the Falconbridge, Kidd Creek Concentrator in a modified D Division circuit. The circuit was commissioned in the fall of 2004. Ore is crushed at the minesite to –19 mm and trucked to Kidd for delivey into the 4 parallel fine ore bins.Ore is milled in a rod mill followed by cyclones and 2 parallel ball mills. The grinding circuit treats Montcalm ore at an average feed rate of 100 wet tonnes/hour (750,000 tonnes/annum) and produces a flotation feed particle size of 83% -53 um. A simple flowsheet including bulk Cu/Ni roughing and 2 bulk cleaning stages followed by Cu/Ni separation in 2 stages is practiced. Soda ash is used as a pH modifier in bulk flotation. SIBX is the collector. Lime and Dextrin are added into Cu/Ni separation for the depression of pentlandite."

Jan 1, 2007

By Denis Thibodeau

his paper describes a study of an altered mining extraction and the resulting Rockmass response at VALE?s Creighton Mine. Typically, the deep mining zones have strict stope extraction guidelines to ensure safety and productivity; however, these guidelines offer low flexibility or few options for stope sequencing. The 402 O. B. being in a good rock mass, at moderate depth and stress regime at Creighton, offered an opportunity to drive a more flexible mining sequence with stopes and a pillar. A three-phased approach was used to mitigate risk of the mining plan: 1- Numerical modelling to fully anticipate rock mass response to the proposed mining sequences. 2- In situ seismic monitoring to collect stress and seismic activity data. 3- Analysis of the in situ data to correlate to the modelling results. The creation and the extraction of a pillar in the 402 O. B. was successfully completed. The recorded seismic activity agrees well with the numerical modelling since most of the seismic activity is localised in the hangingwall where the deviatoric stress corresponds to an early damage process. The moderate levels of deviatoric stress cause localised failure with low level of seismic activity.

May 1, 2013

By Emilio Giuseppe Sarno Severi

Mining and Petroleum Similar Industries ?Asset Intensive ?Exposed to market volatility ?Highly Risky Operations ?Scarcity of Experienced and Trained resources ?Operating in diverse countries with different cultures ?Increasing Environmental and Safety Regulations

Nov 1, 2011

By Jan E. Nesset, Phillip J. Mackey, Joo Y. Kim, Giovanni Di Prisco, André R. Laplante

Understanding the appropriate gold recovery to associate with copper recovery when assessing laboratory testing on porphyry deposits is often complicated by several factors including variable and/or complex mineralogy, and the variability contributed by the low Au content of the various flotation products. As a result, gold recovery is often underestimated and the value contributed by the gold to project economics is less than it should be, a problem that could influence overall project viability. Typically, for these types of deposits, the gold recovery is found to be lower than the copper recovery. In this unique project, having the objective of seeking a better understanding of gold recovery relative to copper recovery, mill feed samples from a selection of six operating world-class Cu-Au low-grade deposits were collected along with the mill metallurgical results for the corresponding sample periods. The samples were subjected to laboratory flotation tests, as well as the Laplante gravity recoverable gold (GRG) test, mineralogical assessment and cyanidation leaching. The aim was to better understand the copper and gold recovery relationship, the links between laboratory and plant flotation performance, the influence of mineralogical differences, and the potential for enhancing gold recovery by gravity recovery techniques. A new correlation of copper and gold recoveries based on the results is presented in the paper. The results showed that the link between copper and gold recoveries established in the best laboratory tests were maintained in the plant results, and further, that the potential for improving Au recovery by gravity or flash flotation methods is directly proportional to the amount of gold greater than 75 microns.

Jan 1, 2005