Search Documents

Blasting effectiveness must be gauged by total production costs. ANFO charges made up in polythene "sausages" are not as profitable as is indicated by the price of ANFO. All-slurry charges are warranted only where blastholes cannot be dewatered effectively, or where drilling costs are very high. An increase in blasthole diameter leads to coarser fragmentation. This effect is most pronounced in tough and massive or blocky strata, or in ground which consists of unfissured boulders in a softer matrix. When ANFO and some slurry-type charges of small diameter are used in plastic-acting ground, charges may fail to detonate through precompression by charges fired on an earlier delay. The optimum blasthole length is rarely less than four times the burden distance. For best results, blastholes should be inclined to the vertical and parallel to the face. Nominal burdens and spacings are often altered radically by the initiation sequence. For best fragmentation, all blastholes must have good effective faces, and should be effectively stagg- ered with an actual spacing:burden ratio in the approximate range 2.0-5.0.

Jan 1, 1975

Most mineral products exported from Australia to Japan, with the notable exception of coal, are purchased with weight and quality determined on discharge. Sampling of imported minerals for purpose of payment is done at facilities owned and operated by the purchaser. The selling shipper is represented at the weighing, sampling and testing by an independent inspection group who supervises the whole procedure. Sampling and testing are done within the provisions of the contract between the two parties, and normally in accordance with the relevant Japanese Industrial Standards (JIS). These JIS specify such things as the number and mass of increments to be taken; the practice of taking these increments; the method of determination of moisture, size distribution and quality. The JIS concerned with sampling however, are meant to be basic guides rather than rigid rules. Hence sampling and testing practice varies from plant to plant. In general Japanese sampling facilities and methods are elaborate and efficient. Opportunity is given for the discussion of varying technical viewpoints between consumer and shipper. However the resolution of differences and the implementation of changes normally takes a long time. Such discussions seem best reduced by prior contract agreement on reasonable specifications and detailed testing methods. The independent inspectors

Jan 1, 1976

The subject of government involvement in industry is, to say the least, a touchy one. For many it conjures up thoughts of socialisation or nationalisation. For others it is a desirable objective and is seen as a means of social reform by giving government a greater say in the control and distribution of human, financial and natural resources for the betterment of the community. Whatever your point of view, it is difficult to deny that government involvement exists to lesser or greater degrees in all industries. The mining industry is no exception and the degree of government involvement is probably greater than it is in other industries. I think it is important to remember when talking about government involvement in industry to recognise that there are different types of involvement and that all governments have a right, if they so desire, to become involved in whatever way they choose. The decision of a government to increase its direct or indirect involvement must, of course, be taken in the national interest. Governments, if we are still old fashioned enough to believe in ministerial and electoral responsibility, must make up their own minds about whether their actions are in the national interest and they must be prepared to accept the consequences of that action, good or bad. For instance, they must decide

Jan 1, 1975

Access to land for exploration, development and mining purposes is extremely critical to the viability of the mining industry and subsequently the well being of society.The mining industry has been subject to environmental controls and considerations for the past 20 years. Today there is greater land use competition and more debate as to its use. To retain reasonable access the mining industry must comply with the rules and regulations by which it is governed.A new set of rules and regulations have been approved for use in Queensland, known as the Mineral Resources Act 1989. This Act clearly outlines the titles available and the requirements to obtain access.There are three main titles of interest to mining companies. These are an Exploration Permit, Mineral Development Licence and a Mining Lease.The Exploration Permit (EP) is for exploration purposes. Applications for EP's are assessed on their content and past performances. An EP is granted subject to a security deposit and conditions. Prior to entry the EP holder is required to inform the land owner of the proposed activities and times of entry.

Jan 1, 1990

By J Szymanski, Y Hu

Excavation engineering involves complex processes for primary and secondary extraction of materials. The shovel excavators bear varying mechanical energy input and stress loading across the working bench during excavation. These varying mechanical energy input and stress loading effects cause significant wear and tear and fatigue failure in equipment components. These effects further result in unplanned downtimes, reduced efficiency and high production costs. In addition, the mechanical and electrical control systems must be operated in efficient profiles to generate maximum outputs and efficiency from these excavators. Efficient technologies are therefore required to solve these problems in order to reduce production costs and increase efficiency. In this paper, the authors develop a rigorous simulator for a hydraulic shovel in a surface mining environment. The finite element model is used to capture the stress profile within the shovel components during excavation, such as, the bucket, stick and boom assemblies. The profiles are classified into normal, critical and extreme ranges, with appropriate corrective measures to avoid extreme loading conditions. The loading capability of shovel excavators can be examined by assessing its structural strength against all possible maximum loads working on the equipment. The dynamic model is used to define efficient profiles of the critical structural components of hydraulic shovels during digging operation. This assessment is used to locate the maximum possible loads and the critical sections of the structures. The method presented in this paper forms the basis for developing comprehensive simulator models for efficient shovel operations in constrained mining environments.

Jan 1, 2003

Portable crushing at Duval Corporation's Sierrita open pit mine has proven both the economics and operability of large, hardrock, portable systems. In-house expertise was utilized to create a system incorporating both operational and maintenance features requested by operating personnel. The monitor/control system involves over 400 channels of information and is based on a DEC 1SI 11/2 microprocessor communicating with seven microprocessor-based data acquisition systems over a 4-wire, multidrop link. The year and one-half successful operation affirms the design philosophy and the hardware/software implementation.

Jan 1, 1985

By P J. Harper

Maximising shareholder value is a widely stated strategic goal of many mining companies. Mining projects can be capital intensive and achieving good returns is essential to encourage future investment in the industry. Despite the widely accepted importance of shareholder value, the minerals industry is often accused of providing relatively poor returns when compared to other industries. There are many recent and well publicised examples of minerals companies that have failed to deliver value to their shareholders. There are numerous business improvement initiatives employed within the mining industry to assist mine operators improve performance. Some are more effective at creating value than others. Benchmarking is one technique that is commonly used to identify performance gaps and target and prioritise opportunities for improvement. However to be effective, Benchmarking must be used appropriately and result in actions that lead to measurable operational improvement. When conducting a Benchmarking project it is important to remember that the aim should be to improve value. For this to be achieved, the strategic goals must be incorporated into the process. This paper details a structured and comprehensive approach to conducting a successful Benchmarking project. Focusing on Benchmarking as a technique for measuring and improving operational performance in underground mines, the underlying drivers of best practice in underground mining are identified.

Jan 1, 2005

The link between exploration success and new ideas from research and development (R&D), although often assumed, is rarely well explained or well illustrated. One issue is understanding the role of innovative ideas in the exploration process, and another is determining the relative contributing factors to an exploration success. A useful measure of gold exploration success over an extended time period and geographic area is discovery rate (θ): Discovery rate θ = gold discovered/exploration expenditure (usefully expressed as tonnes of gold per $1 million). The total gold discovered is strongly leveraged to discovery rate, as any increase in θ typically has a positive effect on exploration expenditure. Hence, improving the discovery rate is a key driver for a sustainable mineral industry, especially for gold. There are very few ways to influence θ beyond innovative R&D ideas and breakthroughs, and well-motivated and trained staff. The Australian gold industry has experienced exceptional exploration success with 9956 tonnes of gold discovered from 1979 to 2003, inclusive. This equates to: Discovery rate θ = 0.9 t/A$1 M Two-thirds of this gold has been found in the Yilgarn craton of Western Australia (6265 tonnes Au). Without this exploration success, there would have been no platform on which to build the current gold industry and to take advantage of elevated gold prices and advances in mining and processing. Several causes of the Western Australian gold success have been proposed, and more than one may be correct. Gold price, and mining and processing advances have all had influence; but exploration success and discovery of gold were essential to add to the miniscule resource base of 1979. A comparison of the exploration methods used to search for gold in the Yilgarn craton in 1979, and 1990, highlights a small number of breakthrough ideas introduced to the industry during the 1980s, and in most cases emanating directly from local R&D. By the 1990s, these ideas were being used in most gold exploration programs in the Yilgarn craton, and are still used today. These six breakthroughs are: epigenetic timing of gold deposit formation (ie after formation of rock sequence), chemical and mechanical role of host rocks, relevance of carbonate alteration haloes, gold dispersion in the regolith, optimal sampling media, and appreciation of landforms in exploration program design. Interestingly, gold exploration science in Western Australia entered the 1980s period without rigid paradigms in place regarding gold deposit formation; there was a balance between descriptive and genetic models, there was scope to research gold deposits from microscopic to global scales and there were highly effective industry research uptake processes in place: it is suggested here that these favourable conditions contributed to the exploration success and industry growth.

Jan 1, 2007

By E A. Agorhom, P N. Aabulleh

The bulk of the worldÆs production of iron ore is processed into steel. The needs of the steel industry therefore demand a high exploration and exploitation of iron ore. One trend within the industry has been a great increase in the demand of iron ore and this is reflected in an increase in world steel production from 1955 to date. In addition to the high demand for steel, is ChinaÆs high appetite to feed its steel industry. It is therefore important that the iron ore potential of Ghana is showcased for eventual exploitation by potential investors to meet this enormous demand for the commodity in the industry globally. Ghana has three main iron deposits of potential industrial and commercial importance. They are: Shieni sedimentary iron ore (reserves: 1.270 X 106 metric tonnes), Pudo titaniferous-magnetiferous iron ore and the Opon-Mansi lateritic iron ore deposits. The Opon-Mansi iron ore deposit occurs in the Western region of Ghana. The ore deposits are located on top of the range of 15 hills, which extend over a distance of 24 km from Opon-valley, south of the Western region to Dunkwa. The area has an estimated 147 Mt of iron deposit, with Fe content of 52.5 per cent. This paper looks at the iron ore potential of Ghana and how it is capable of attracting potential investors to exploit this valuable mineral for global consumption.

Jan 1, 2007

Microorganisms have been used throughout history for the benefit of mankind with some of the earliest applications being in the production of fermented foods and beverages. Reactions involving inorganic substances such as metals, sulphur and sulphide compounds were hardly ever used until the early 1900s when it was discovered that Thiobacillus ferrooxidans was capable of promoting the oxidation of metal sulphides in ores. Today, it is widely recognised that biotechnology has great potential in the minerals industries, particularly in such areas as the leaching of low-grade ores of metals such as copper, gold and uranium; removal of heavy metal ions from process streams and from liquid process wastes; and in the desulphurisation of high-sulphur fuels. Although widespread commercialisation of mineral biotechnology has not yet been achieved, it is estimated that by the Year 2000 mineral biotechnology will have a significant impact on the minerals and metal industry and will probably account for tens of billions of dollars worth of annual production world-wide. This paper examines the actual and possible future applications of biotechnology in the minerals, metal refining and fossil-fuel processing industries. Firstly, the important chemical (and biochemical) principles involved in bio-dissolution of metals from ores and solid wastes, and in bio-accumulation of metals from process and waste solutions are reviewed, including leaching practices - past, present and future. Microbial desulphurisation of coal, and microbially-enhanced oil recovery are also discussed. The practical aspects of genetics and genetic engineering, the types and characteristics of those microorganisms important to mineral biotechnology, and the current research trends are reviewed as well. KEYWORDS: Biotechnology, microbial leaching, bioaccumulation, biosorption, bioleaching, biohydrometallurgy.

Jan 1, 1993

By L M. van Niekerk

The mining of iron ore is a high volume low margin business because the value of this commodity is significantly lower than that of base metals. The main metallurgical challenges in most of the iron ore projects proposed for treatment nowadays have been in finding the optimum flowsheet for the treatment of magnetite ores, mixed magnetite-hematite ores and even ores that have banded ironstone formations (BIF). The associated plant designs incorporate very high capacity milling systems to grind the ore down prior to magnetic separation and in being highly capital intensive requires substantial investment in mega processing plants with associated infrastructure to mill down the run-of-mine ore to the desired treatment size for upgrading.To minimise the cost of infrastructure, better beneficiation techniques and technologies are being sought to assist in reducing upfront ROM feed to allow for reduction in overall treatment plant footprint necessary in extracting the desired downstream product. This paper discusses such beneficiation techniques and advancement in technologies for the upgrading of coarse and fine iron ore utilising dense media separation (DMS), jigging, wet magnetic separation, dry magnetic separation, flotation and x-ray processing.Another group of iron ore projects involve the mining of hematite ore below the water table. Often the mined ore is wet and sticky. This combination requires high capacity processing of feed material utilising large scrubbers or attritioning units to effectively remove the slimes component present in the feedstock. The fines removed, usually below 1 mm, are then discarded in large tailings storage facilities. Approaches to recovering the saleable material contained within these fines will also be investigated in this paper. This not only implies possible reduction in slimes discard footprint, but also holds potential benefit in augmenting overall yield and recovery of hematite product.CITATION:van Niekerk, L M, 2013. Fine and coarse iron ore beneficiation - An evaluation into global technologies and techniques, in Proceedings MetPlant 2013 , pp 584-598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

The investment worth of a mineral deposit can only be realistically evaluated in relation to specific engineering design criteria, which fully details the proposed method of exploitation. These criteria have not in general been taken into serious consideration when leaseholders have reported reserves in the past. In fact, many "reserve" figures quoted are probably more correctly classified as geological resources. The industry now recognises that it is necessary to take into consideration not only grade and mill recovery factors, but also likely mining and processing costs as well as the current market price for the commodity. Once having estimated those costs which are applicable to the resource under study, they can be deducted from the gross inherent worth of the orebody to result in an estimate of the potential net revenue. Through a process of interactive trial mine designs and evaluation, reserves can be quantified to provide an estimate of the available recoverable economic reserves given a set of assumed cost and operational parameters. It follows then, that the available economic reserve recoverable from a given resource will vary from time-to-time as cost and price factors vary in response to changing technology and economic factors. A methodology is described which may be used to derive economic recoverable reserves based on a computerised model of the geological resource data and appropriate economic and operational cost algorithms. Examples are provided from both coal and gold studies to illustrate the impact of economic criteria on the magnitude of the reserve figure reported for each project.

Jan 1, 1987

The truly scientific method in the study of such questions at the present day is the reverse of that which was followed in the early days of geology, when after the observation of a few isolated facts, some great geological mind was led to a general theory, and humbler followers were only too apt to do mild violence to nature in order to make her facts conform to it tt accumulates year after year a multitude of facts of patient observation, supported by studies with the microscope, and in the laboratory, avoiding general theories, and only making such deductions in regard to locftl conditions as are supported by the overwhelming evidence of facts. S. F. Emmons, on the geological distribution of minerals in the United States, at the "world's congress" of mining engineers, Chicago. Fig. l.-This exhibits the general stratigraphical characters of the southern lodes. The" Indicator" veins, the great barren lode masses, a later fissure than all of these (" B "), and the auriferous lodes of last series cleaving the wrinkled terraces and the older lodes also are" Indicator" veins. B is a later formed vein that leaves no " depositions" behind. ooe are fragments of the" most ancient'' lode wreckage. Db are the auriferous lodes and correspond with those lodes, also whose auriferous characters are not result of secondary impregnations.

IN the ordinary course of treatment of pyritic ores or concentrates, whether for the recovery of copper, tin, gold, or any other contents, the removal of some or all of the sulphur contents is almost invariably the first step. The practice is to roast the ore in a current of air so that the sulphur is oxidized to sulphur dioxide and the metal constituents are changed from sulphides to oxides. If it is feasible to produce sulphuric acid in conjunction with the treatment process, the sulphur can be usefully employed; but if this is not possible, then the sulphur contents not only become a dead loss, but tend to be a nuisance as well in the surrounding neighbourhood.The problem of avoiding this disadvantage and making economic use of the sulphur has had attention from the early days of scientific metallurgy, and in the past few years very special efforts have been made both to drive part of the sulphur as such from pyrites and recover it, and to replace the sulphur in the S02 by carbon, with the production of carbon dioxide and precipitation of the sulphur. So far economic success does not appear to have crowned these efforts. In the case of pyrites, of the two atoms of sulphur which go to make the FeS2, the first is very lightly held. Dissociation is effected by heat alone at a temperature which is given by Peters as 5160 C.Now, sulphur and hydrogen will unite or burn together, with the production of sulphuretted hydrogen. It occurred to the writer that, if hydrogen was passed over pyrites heated to the above temperature, this first atom would be snatched away by the hydrogen, and could possibly be economically recovered.The first step consisted of some simple laboratory experiments. From these it was found that this first atom was readily removed, and that the extraction was practically complete. Further, the reaction took place at a low temperature, a dull red heat being sufficient.

Jan 1, 1923

By Szpindler G

The results of pot-furnace tests with 35 bituminous coals from 20 seams in New South Wales and Queensland were used to establish the relationship between coal properties, as determined by standard laboratory tests, and the combustion process. The rate of combustion is influenced chiefly by the expansion of the fuel bed, but this cannot be accurately predicted from the crucible swelling number of the coal.The effects of various other factors, such as calorific value and ash yield, were investigated and statistical analysis of the results shows that the coals could be classified satisfactorily according to two experimentally derived parameters, namely heat-release rate at an air flow rate of 260 lb/sq.ft/hr and air flow rate giving stoichiometric combustion. The grouping obtained is shown to be related to ash yield and swelling number.INTRODUCTIQNThe rate of heat release from the fuel bed of a travelling grate stoker and the efficiency with which the heat is used depend upon the design and method of operation of the furnace as well as upon the properties of the fuel. It is difficult to draw general conclusions concerning the influence of fuel properties from tests on a single stoker installation. In the pot-furnace test, on the other hand, a part of the same combustion process as occurs on a travelling grate is carried out in isolation, uninfluenced by furnace design variables, and consequently the effects of coal properties and of the method of pretreatment can readily be demonstrated.While the combustion pot provides a rapid method of assessing the combustion characteristics of a fuel during the ignition and burn-out stages under standard conditions, and of predicting changes in performance with changes in fuel or in air flow rate, it is unable to simulate certain features of furnace design and operation. Data from combustion pot...

Jan 1, 1962

The correct design and effective operating strategies of metallurgical plants require a constant analysis of data gathered for process control, or for due accountability. Conventional, oldfashion statistical tools often fall short of helping management, either because they are too complicated and ambiguous, or because they fail to address structural problems leading to causes of setbacks. This paper focuses on three statistical tools known for their practicality and the in-depth perspective they offer in attempts to retrieve important information from existing data. These tools also provide a better appreciation of the importance of carefully selected data quality objectives. Chronological data are meticulously gathered and stored at considerable expense: They have value, and it is the duty of management to take full advantage of them. These three selected tools are the variogram and its auxiliary functions, the moving average and its auxiliary functions, and the relative difference plot. This paper offers solutions, and a reference for managers to optimise metallurgical plants.

Jan 1, 2002

By T GRAHAM-TAYLOR

A trend towards mining more complex and economically marginal orebodies, often combined with increasingly tight product specifications, increases the number of variables which need to be considered in production scheduling. Linear programming incorporating integer constraints can be used to create production schedules which are practical as well as mathematically optimum. Factors which can be taken into account include variability in product stockpiles, targets for head or product grades, production of different material types, production from different areas, production targets for loaders, and dependencies between mining blocks. For each schedule an appropriate objective for optimisation must be chosen. Examples of objectives are: to minimise or maximise grade variation; to minimise waste movement; and to minimise movement by front end loaders. A staged approach to the implementation of computer systems based on linear programming optimisation is Proposed.

Jan 1, 1992

By J Watson

Electronic detonator technology has been under development for the last two decades. Currently, there are a number of systems commercially available with several others still under development, each with its own unique features. This technology can offer a significant advantage to the drill and blast engineer through their ability to initiate an explosive charge at the æplannedÆ time. This new technology has created huge interest within the drill and blast community and also raised their expectations to produce better blasting outcomes. In many cases, specifications (or even expectations) of desired blast results are not properly defined. Interaction between the input variables (rock mass characteristics and blast design) and results (fragmentation, throw, damage, ground vibrations, etc) and their mechanisms, or relationship to one another, are not very well defined or understood. That is why rock blasting is still considered by many as an art rather than science. With one of the few remaining variables (cap scatter) now controllable, todayÆs blaster finally has the ability to apply science to his trade. Even though electronic detonators are available and becoming more commonly used, current field practices are not always conducive to extracting or deriving the maximum benefit from this new technology. In the authorÆs opinion, the following need to be understood to derive and sustain the maximum value: clear definition or specification(s) of desired outcomes from a given blast; impact of different features in an electronic detonator system (precision, accuracy, flexibility, reliability, etc) and their impact on the desired blasting outcomes; interaction of blast design variables (energy, energy distribution, timing, blast geometry) and their impact on desired outcomes; impact of rock mass variability and quality of blast implementation on the desired blasting outcomes; and critical need to utlilise appropriate tools and systems in order to measure and quantify benefits.In the authorÆs opinion a scientific implementation process is the key to derive the benefits. This paper analyses the industryÆs preparedness to derive the benefits from this technology and proposes a scientific methodology to understand, evaluate and sustain the value from this technology.

Jan 1, 2004

By A F. Idziak

The aim of the present study was an application of coal optical property measurements for analysis of paleostress field existing in fault zones of the Upper Silesian Coal Basin (USCB) during the coalification of organic matter. Measurements of vitrinite reflectance were carried out on coal samples taken near a hanging stope of the Klodnicki fault. Other samples had been taken in vicinity of the Krzyzowicki fault. The Klodnicki fault is one of the main tectonic discontinuities in the northern part of the USCB. It is postulated that its origin is related to the deep-rooted latitudinal discontinuity in crystalline basement of the basin. The Krzyzowicki fault is located in the western part of the USCB where fold tectonic style dominates. Vitrinite, one of the basic components of hard coal is generally considered as optically anisotropic material. Anisotropy of physical properties is induced mainly by stress, which arranges vitrinite structure. Vitrinite anisotropy can be described by an ellipsoidal model called reflectance indicating surface (RIS) which is a geometrical representation of the optical anisotropy tensor. The investigation of the RIS for vitrinite was carried out on coal samples. The apparent maximum and minimum reflectance values measured for a single vitrinite particle were plotted against corresponding bireflectance to construct the reflectance crossplot. Interpretation of this plot yielded the magnitudes of the RIS three principal axes. The data obtained point to differences in optical anisotropy of coal under the study. The coal samples taken from block tectonic zone near the Klodnicki fault had mean reflectance value of less than 0.80 per cent. Their anisotropy coefficients were about 0.1. Optical properties of coal changed from the biaxial positive in the western segment of the fault to the biaxial negative in its eastern part. It suggests that past tectonic stress was greater in the western part of the zone than in the eastern one. Coal originated from a fold tectonic zone at the vicinity of the Krzyzowicki fault has mean reflectance value much greater than from previous region (ÿ1.20 per cent). Its optical anisotropy coefficient is equal to about 0.07. It suggests that paleostress field was more isotropic. The presented study shows the usefulness of coal reflectance measurements in the analysis of paleostress field existing during coalification process.

Jan 1, 2003

By Bertrand D. L

Although investigations into treatment of Mt. Keast (a hill of tailing) began as early as 1940, it was not until the Imperial Smelting Furnace (I.S.F.) was installed at Cockle Creek by Sulphide Corporation that its treatment became eooncmically feasible. Early investigations and milling operations which began in mid-1976, with their developments are described. Metal recovery involves sulphide flotation, oxide flotation and gravity techniques.

Jan 1, 1983