Search Documents

By Churchill M

One of the significant changes which has occurred in the flotation sector of the minerals industry, over the last two decades, has been the successful development of the very large flotation machine. The last twenty years has seen the volume of the individual cell, available to the industry, increase by a factor of ten. Today, new mills, and existing mill modernization plans, can consider individual cell volumes as large as 85 m3 with the certainty that the metallurgical performance capability of the large machine is inherently as efficient as the smaller machine. The large flotation cell offers benefits to the user such as reduced floor space, lower total power, process control simplification, and reduced maintenance. However, the flotation machine size selection process, based on overall installation economics, must include such factors as process tonnage, flotation kinetics characteristics, and metallurgical performance objectives. This paper discusses the flotation machine size and circuit arrangement selection based on both metallurgical performance and economic considerations. A computer based flotation kinetic analysis technique, which has proven valuable in quantifying the metallurgical response of flotation circuits having different cell sizes and number, is utilized to illustrate the selection of cell size and arrangement best suited to a client's Requirement.

Jan 1, 1991

By Waters A. G, Nightingale R. J

The quartzite added at the blast furnace for the purpose of adjusting the chemistry of the burden inputs is shown to have a disproportionate impact on both the level and the variability of the hot metal silicon (HMSi). This conclusion is supported not only by direct correlation involving data from five blast furnaces, but also by mass balances. In one case the R2 correlation coefficient was 0.96 and the mass balance was accurate to within five per cent for a wide range of quartzite additions. The results indicate that as much as 43 per cent of the silicon in the added quartzite reports directly to the hot metal. Indeed, silicon from quartzite was found to be much more likely to report to the hot metal compared to silicon from regular sources (eg coke and sinter), reflecting differences in the activity of the silicon source.

Jan 1, 1994

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important alvantage. of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate: (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elim-ination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the thresthold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step copper smelting is still a process of the future.The paper describes the potential advan-tages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985

By Fee BS

This paper describes four new families of collector products which are currently being introduced at the industrial level. A brief summary of the chemical basis behind each product family will be given. This is then followed by a selection of flotation examples which illustrate the more important use characteristics that have been observed to date. It is becoming more apparent with further testing that these four new product families can offer both technical and economic advantages to the industrial flotation process operator.

Jan 1, 1993

By J Kok

"In some underground mines it has been observed that the primary focus during feasibility studies is to determine the best way to mine the defined orebody. Some studies have been conducted without sufficient consideration of the ventilation and cooling requirements or the risk from exposure to associated airborne pollutants caused by the mining operations.Following the hierarchy of control to manage risk, numerous problems of the ventilation systems in some underground mines could have been avoided if sufficient consideration was given to the ventilation requirements to manage heat, airborne pollutants and leakage during the feasibility study phase. If the constraints and hazards were well defined and understood at the time of the study, efforts could have been made to eliminate or substitute the hazards to decrease the risk. Some of these problems include but are not limited to: primary fan locations heat loads diesel exhaust ventilation design based on the production requirement fire/emergency response strategies.This paper highlights areas in the ventilation discipline that are sometimes overlooked during feasibility studies. It will also highlight the importance of the Ventilation Specialist during these studies. Experience and knowledge of best ventilation practices must be applied in feasibility studies.As a result of adequate consideration to all ventilation aspects in the feasibility study phase, risks will become lower in terms of health, safety, production loss and equipment downtime caused by heat.CITATION:Kok, J, 2014. Feasibility studies – what should be considered in terms of ventilation, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 197–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By M Danišík

Two drill core samples of haematite/goethite from the Robe River (Western Australia) channel iron ore deposits (CID) were dated using (U-Th)/He methods in order to constrain the timing of iron oxide formation and thereby provide a temporal context for CID genesis. (U-Th)/He ages (He ages) from these samples range from the late Oligocene to Late Miocene and despite a high degree of scatter, they corroborate relationships expected from the internal ooidal stratigraphy: For individual ooids, the ages from haematitic core are older than or indistinguishable from the ages of the surrounding goethitic cortex. The goethitic cortices are, in turn, older than the ferruginised wood fragments recovered from the cementing goethitic matrix.The data suggest the following succession of ore formation phases:• Haematitic cores in ooids of both samples formed in the Early to Middle Miocene.• Goethitic cortices of both samples formed in the late Middle to early Late Miocene. This appears to be the age of goethite cortex formation regardless of depth in the core, which does not support the top-down infill model, genetic model proposed by Heim et al (2006).• Wood fragments form a prominent component of the matrix and were ferruginised during the Late Miocene. Thus the data suggest that the unique environmental conditions for the CID formation existed during the Miocene.A methodological implication of this study is that the temperature utilised for He-extraction from iron oxides has a critical impact on the mobility of parent nuclides. The typical ~1100°C laser heating used for crystalline minerals like apatite or zircon induces loss of U and Th and results in erroneously old ages.

Jul 11, 2011

The Mineragraphic Section of the Council for Scientific and Industrial Research has had occasion from time to time to examine rocks, ores and concentrates from the Yatukoula goldfield, Fiji. The results of the examinations have been supplied as Mineragraphic Reports and have been supplementary to various investigations carried out by the mining companies on ore treatment, or by visiting geologists on the nature of the rocks and lodes. The presence of tellurides was determined in 1935, though incorrectly as nagyagite. The general absence of lead, except in traces, was soon afterwards discovered, and it came to be recognised as the mines were opened up that the chief telluride minerals on the field were sylvanite and native tellurium. Specimens of the tellurides have been provided from time to time by E. G. Theodore, Managing Director of the Emperor Mines Ltd., and of the Loloma (Fiji) Gold Mines N.L., and further material was recently obtained, as the result of a visit to the field at the invitation of Mr. Theodore.The aim of this paper is to describe the occurrence of the tellurides in these specimens. The work has been carried out as part of the programme of research of the Mineragraphic Section.THE VATUKOULA GOLDFIELDThe Emperor, Loloma and Dolphin mines are situated at Vatukoula, six miles, south of Tavua, on the north coast...

Jan 1, 1949

By R L. Brathwaite, R Carver

The REGCHEM (Regional Exploration Geochemistry) database of open file mining company data, managed by GNS Science, has recently been upgraded with the compilation of additional data, especially for the Otago region (see http://maps.gns.cri.nz/website/minmap). In June 2007, data compiled for the Otago region included more than 2000 stream sediment samples from 19 surveys, more than 800 BLEG (bulk leach extractible gold) samples from 12 surveys and a few pan concentrate samples. The stream sediment samples were typically analysed for Au and As, and in many cases for other elements including Cu, Pb, Zn, Sb, W and Mo. The BLEG samples were analysed for Au and in some cases also for As. The main exploration target was mesothermal gold deposits in the Otago Schist, although one survey of the Otago Peninsula targeted potential gold deposits associated with the Dunedin volcanic complex. Geochemically, the mesothermal gold deposits are characterised by anomalous As and Au, with some also characterised by anomalous W and Sb, and these four elements are the best pathfinders in stream sediment geochemical surveys. The introduction of lower detection limits in Au analyses in the more recent stream sediment surveys and in the BLEG surveys enables the use of this element as the primary pathfinder for mesothermal gold deposits.

Jan 1, 2007

A practical approach has been developed for the design of both grates and pulp lifters. It is based on: an appreciation of the process interaction between grates and pulp lifters, an interpretation of mill charge structure as it relates to discharge through grates, and an analysis of pulp and solids flow in pulp lifter channels. This approach can be used to improve the overall discharge effectiveness of AG and SAG mills.

Jan 1, 2000

By J Vann, S Jackson, O Bertoli

Ordinary kriging and non-linear geostatistical estimators are now well accepted methods in mining grade control and mine resource estimation. Kriging is also a necessary step in the most commonly used methods of conditional simulation used in the mining industry. In both kriging and conditional simulation, the search volume or ækriging neighbourhoodÆ is defined by the user. The definition of this search can have a very significant impact on the outcome of the kriging estimate or the quality of the conditioning of a simulation. In particular, a neighbourhood that is too restrictive can result in serious conditional biases. The methodology for quantitatively assessing the suitability of a kriging neighbourhood involves some simple tests (which we call æQuantified Kriging Neighbourhood AnalysisÆ or QKNA) that are well established in the geostatistical literature. The authors argue that QKNA is a mandatory step in setting up any kriging estimate, including one used for conditioning a simulation. Kriging is commonly described as a æminimum variance estimatorÆ but this is only true when the neighbourhood is properly defined. Arbitrary decisions about searches are highly risky, because the kriging weights are directly related to the variogram model, data geometry and block/sample support involved in the kriging. The criteria to look at when evaluating a particular kriging neighbourhood are the following: the slope of the regression of the ætrueÆ block grade on the æestimatedÆ block grade; the weight of the mean for a simple kriging; the distribution of kriging weights themselves (including the proportion of negative weights); and the kriging variance. Outside of the technical geostatistical literature, there is little in the published domain to describe the nature of QKNA and no practical presentation of case examples. In this paper we attempt to redress this by setting out the calculations required for QKNA and defining some approaches to interpreting the results. Several practical worked mining case examples are also given. Finally some comments are made on using the results of QKNA to assist with block size selection, choice of discretisation and mineral resource classification decisions.

Jan 1, 2003

By Waters JC

Pseudoclastic hydrothermal alteration textures occur within quenched coherent dykes forming part of a subaqueous dome complex (-4 Ma) on Ponza Island, Italy. These textures are similar to those observed in considerably older (-500 Ma) subaqueous volcanic rocks at a number of localities throughout the Mount Read Volcanics in Tasmania and elsewhere in ancient volcanic sequences of this type in Australia. This is significant because the processes of formation, hydrothermal alteration and secondary mineralisation of ancient volcanic sequences may be better understood if we can make comparisons with modern analogues. Observations at Ponza imply that these pseudoclastic alteration features form synvolcanically or immediately after dyke emplacement and lava extrusion. This is compatible with scenarios presented for their formation in ancient sequences in the Mount Read Volcanics, Tasmania.

Jan 1, 1995

The port of Townsville is situated on the main north/south rail system of the Queens- land Government Railways and is the eastern terminus of the east/west rail link from Towns- ville to Mount Isa. With a stable beef and wool producing area along the east/west rail route, the expanding mineral industry development at its western end and the continuing growth of the Townsville region the administrators of the port are continually'keeping abreast and ahead of port development to ensure an effective and economic growth of port facilities to meet the needs of the area served by Townsville.

Jan 1, 1974

By P Benjamin, H Bohannan, C Farr

Geoffrey Blainey's historical account of the mining activity on the west coast of Tasmania, æThe Peaks of LyellÆ documents the changes over 130 years of activity in the region. Commissioned by the Mount Lyell Mining and Railway Company, emphasis is placed upon the development of the Mount Lyell Mine in Queenstown. Chapter 19 æWidening HorizonsÆ details the review the Mount Lyell Company undertook in 1904/05 to ensure the future of the operation, following the pessimistic outlook regarding diminishing reserves and poor grade ore. The analogies documented between the Mount Lyell Company at that time, and Gold Mines of Australia 90 years on are remarkable, with both companies demonstrating a commitment to the Mount Lyell area through active exploration, the proactive search for alternative technology and the recognition of the valuable human resource. As Blainey writes (Blainey, 1993), æwith its expanding chemical works, its huge Tasmanian mines, its railways and smelter, its coke works and its mine crusade, Mount Lyell was probably one of the nation's five great industrial companies in 1906 or 1907. This brief phase of industrial and mining expansion had its seed in the threat of extinction . . .Æ After a number of reprieves, the Mount Lyell mine did stop production in 1994, but that only provided an impetus for a review and rebirth.

Jan 1, 1998

By Caivin JS, Freeman CJ

The Fairbanks Mining District in central Alaska was discovered in 1902 and since then approximately 7.5 million troy oz of placer gold, 250,000 troy oz of lode gold, and several thousand short tons of antimony and tungsten hap been produced from an area of about 1000 km . Historic lode production was from high grade gold-quartz veins that averaged 1.3 OPT free milling gold. Five main types of mineral deposits' are recognized in the district. I. Conformable, stratabound volcanogenic zinc, antimony, lead, and copper sulfides in places containing gold, silver and tungsten in bimodal metavoleanics (Cleary Sequence). II. Complex precious metal-bearing lead sulfosalt-quartz veins in Cretaceous granitic intrusives. III. Tungsten skarns adjacent to granitic intrusives. IV. Gold-bearing polymetallic sulfide-quartz veins crosscutting metavolcanics and metasedimentary units of the Cleary Sequence. V. Antimony-bearing gash veins along axial plane shears in various lithologies of the Cleary Sequence. Type I and Type IV mineral occurrences are currently being evaluated as low. grade bulk tonnage (target model 16-20 'million tons of 0.05 to 0.15 OPT)'and high grade moderate tonnage (target model 0.5 to 2.5 million tons of 0.5 OPT) gold deposits. The host rocks for Type I mineralization occur over a 30 km strike length and are at least 300 meters thick. Stratigraphic, structural, fluid inclusion, and isotopic data suggest that the Type IV mineralization is related to remobilization of Type I

Jan 1, 1987

By M D. Rosengren, G Gregor, M F. Young

Over the last 15 years the silver/lead/zinc ore treated at Mount Isa became increasingly complex and lower grade. Metal recoveries dropped dramatically, causing a serious decline in profitability. The ætraditionalÆ response of increasing tonnage to reduce unit cost was unsuccessful, since the additional tonnage was even lower quality ore. A major technical and capital program in the 1990s restored metallurgical performance, but business return was still too low and ore quality continued to decline. In 1996 a new, holistic approach integrated the steps of geology, mining, concentrating, smelting, and refining. Previous assumptions about æfixedÆ and æmarginalÆ costs in mining and processing were shown to be wrong. Detailed analysis showed that some ore sources were reducing profit. This led to a fundamental redesign and downsizing of both Mount Isa and Hilton mines. The result was dramatic increases in head grades, metallurgical performance and plant stability without any capital expenditure. The business is now smaller, but more profitable.

Jan 1, 1998

By McQueen LB

The Water Board has been involved in the development and ipgrading of sewerage facilities in the Blue Mountains since 1980. In 1984 the Board prepared a report that dealt with the Blue Mountains Sewage Effluent Management study. Successive 3ovemments have been concerned about development in the 3lue Mountains and the effect this development is having on the luality of the streams flowing into the Blue Mountains National ?ark (presently up for World Heritage Listing).

Jan 1, 1993

By J Vann, C Seymour

Geology is generally treated as a æfront endÆ step in mine development. After infill drilling, the majority of resource estimation, mine-planning, development, mineral processing strategies and operational procedures are planned and implemented with little geological input, particularly in open pit operations. However, significant benefits in overall costs, cash flow, and technical risk reduction can be realised when sound geology is utilised more rigorously throughout the mining process. This under-utilisation of geology in the mining process has arisen due to a combination of factors:A lack of interest in, or knowledge of the full mining process by geologists. Few geologists fully understand where their inputs make critical impacts on downstream users. As a result of this, geologists generally do not focus their inputs towards areas of greatest value added, ie addressing issues critical for other members of the mining team. Most importantly, few geologists effectively communicate their results to the downstream users of their geology models. The results are that the potential benefits of geology, and the appropriate status of geology in the mining industry, are not fully realised. It is fundamental to realise exactly what geologists do. Geologists constrain geological processes and geometry. All geoscientific tools at the geologistsÆ disposal are geared towards one of these goals. An emphasis on geological processes is present throughout the exploration process, whereas in the resource estimation and mine development process an emphasis on geometry is required. The mining process is a web of disciplines that are attempting to optimise development of a resource to provide value to shareholders. Yet few people within these disciplines have a full appreciation of this web, and where sound geology inputs can add value through various feedback loops. Geology inputs do not end at the resource estimation stage, nor are they relegated to grade control implementation. If geologists have an appreciation of the mining process and close liaison with the other disciplines such as geostatistics, geotechnical engineering, hydrogeology, and mining engineering, they can significantly benefit project costs, timelines, and constrain technical risk by addressing their issues at the earliest possible stage. Furthermore, the mining process is not a single pass timeline, but an iterative process where the exploration, resource definition, mine planning and mining loop is continually repeated over the life of a project. Therefore, the potential inputs of geology are critical throughout the mining process. Effective communication of the impacts of geology inputs on downstream users is often lacking on mining projects. The most effective way to communicate geological results is through where it impacts most û project risk. Focussing all geology inputs and communication in terms of potential material risk allows the geologist to be more effective in contributing value to the mining process, and allows the downstream users of geology inputs to better constrain the risks associated with their aspects of the mining project. Through a program of geologists:taking an interest in the entire mining process and identifying critical areas for geology inputs to downstream users (the geologistsÆ clients); focussing geology inputs to address the potentially material issues on mining projects; and communicating their inputs to the æclientsÆ in terms of technical risk, geology will be much better integrated into the mining process. As a result, the potential benefits of geology throughout the mining process will be realised, and the status of geologists within the mining process will be elevated to a more pivotal position.

Jan 1, 2000

By Wright J

Large scale cut and fill mining in narrow silver-lead-zinc orebodies began at Mount Isa in 1964. Initially each orebody was one stope and access was via raises from the level above. Upholing was the principal mining method, although flatbacking was employed where ground conditions were more difficult. Developments since have included access via footwall inclines and connection of all stopes with major crosscuts. Flatbacking is the principal method. The most recent cut and fill operation is now fully mechanised using drilling jumbos, rockbolting jumbos and load-haul-dump units. Improved ground support and drilling and blasting practices have enhanced safety, recovery and productivity in all cut and fill operations.

Jan 1, 1988

IN the course of his employment the Broken Hill Co. the writer has had occasion to use and instruct others in the use of the Shamrock rescue apparatus. This paper deals with the various types of apparatus tested. The common object of the various types of breathing apparatus is to enable the wearer to remain and work for varying periods of time in an atmosphere which is either deficient in oxygen or is poisonous that is, contains carbon monoxide or irritating and irrespirable vapours, such as the smoke from underground fires, sulphur dioxide or ammonia fumes. For any apparatus to be efficient as required in the above paragraph it must fulfil the following conditions;1. Air-tight as regards the passage of the air from the outside to the inside. In atmosphere containing carbon dioxide a slight leak would not render the apparatus useless; but where irritating vapours, such as the smoke from burning oregon and sulphides, are met with, even the slightest leak must be avoided.2. The oxygen supply must be ample, and so supplied that it is not checked by expiration.3. Expiration and inspiration must not be retarded.

Jan 1, 1911

It should be noted that with the passage of time all aspects of the mineral extraction process are becoming more sophisticated and complex. In order to deal with this, the education system should be geared to this continual technological advance.A new scheme is designed to attract high quality school leaven to take up courses serving the mineral industry. After graduation these students will play an important role in the areas of research and development which is essential for the growth of the Australian mining industry.

Jan 1, 1991