Search Documents

Cerro Matoso (CMSA) in Colombia produces ferro-nickel from lateritic ore containing approximately three per cent nickel, using a Rotary Kiln - Electric Furnace (RKEF) process, in which the calcining of the mineral within the kiln is second in importance only to the smelting of the mineral in the Electrical Furnace. This article discusses the installation and operation of an expert system to control the kiln of CMSA. In the CMSA process, the run-of-mine ore is crushed, homogenised, dried and mixed with a small percentage of coal, before being heated up to 900¦C in a rotary kiln in the presence of natural gas mixed with air in a controlled proportion (air/gas constant ratio). The final objectives of the process are the following: ò To reduce to a minimum the iron and nickel oxides in order to convert these into metallic ions; this is a reduction process to facilitate largely the smelting in the electric furnace. Since the reduction is made with natural gas, it is much more economical than the subsequent complete reduction in the electric furnace, since electrical energy is much more expensive by unit of processed mineral. ò To heat the mineral as much as possible to facilitate the subsequent smelting. ò To eliminate totally the moisture content of the ore. An expert system with fuzzy logic was commissioned in 1994 for the control of the kiln and it has operated with good results ever since.

Jan 1, 1996

By Hagarty KA

At the northern margin of New Guinea there is a fundamental problem related to the relative timing of arc- continent collision(s) represented in the Papuan Fold-Belt (PFB) and backarc spreading in the Caroline basins. New fission track dates from basement and sediments within major anticlines of the PFB indicate that uplift occurred at 4.0 ¦ 0.5 Ma. The timing is consistent with the fold and thrust shortening (more than 100 km) of the PFB which occurred in the Late Miocene/Early Pliocene as evidenced by the deformed Miocene carbonates and Pliocene molasse deposits. However, in northern Papua New Guinea, earlier work has suggested that ophiolite emplacement and associated metamorphism occurred in the late Oligocene/early Miocene.The evidence suggests that the late Miocene/early Pliocene deformation was of considerably greater magnitude than the earlier obduction event. The Caroline Plate lying north of New Guinea has been interpreted as a backarc basin which commenced spreading in the Eocene and ceased spreading in the Late Oligocene (about 28 Ma). The remnant arc presently docked to New Guinea was active in the Eocene and Oligocene and is believed to be the arc related to the formation of the Caroline Plate. The cessation of spreading of the Caroline Plate has previously been interpreted to be due to arc continent collision during the Late Oligocene/Early Miocene, but such a collision is now known not to have occurred. In the Cretaceous and Palaeocene subduction was to the south beneath New Guinea, but "flipped" in the Eocene to give a north-dipping subduction zone far to the north of New Guinea, driving Caroline Plate backarc extension. This backarc basin reached a limiting size at about 28 Ma resulting in the end of subduction. With the continued northward movement of Australia, Mesozoic oceanic crust was obducted southward onto the New Guinea margin in the Late Oligocene/Early Miocene. In the Miocene south-dipping subduction beneath New Guinea commenced until the now extinct Caroline Plate arc collided with New Guinea in the Early Pliocene, causing extensive regional compression and sinistral strike-slip faulting. This new tectonic framework suggests that backarc basins reach a limiting ridge-trench distance of 1000-1500 knm, beyond which "subduction-pull" cannot drive further spreading so subduction and spreading are terminated.

Jan 1, 1987

The Southwest Pacific is a region of active volcanism and geothermal systems. Only in New Zealand have the geothermal systems been exploited for electricity generation and industrial processing. At present, approximately 280 MWe of geothermal electricity is generated in New Zealand. A considerable amount of further exploration work is required before the total geothermal potential of the region can be assessed and before the significance of these resources can be judged against other local energy sources.

Jan 1, 1990

By G Chitombo, M Ruest

In surface mining, studies of the kinematics of blasted rocks using high speed film/video image analysis have allowed the estimation of the starting time, direction and magnitude of visible movement of fixed sections of the free face. Horizontal displacement versus time plots from discrete targets at the face generally report changes in slope over very small time intervals. These changes indicate step increases in velocity due to the action of explosive gases. In practice, the onset of rock mass movement, different to localised spalling, has been associated with a response time which exceeds the combined times of detonation, propagation and reflection of stress waves. This time is referred to as minimum response or burden movement time. As an engineering index, burden movement time has been used to provide guidelines for the selection of inter-hole and inter-row delay sequences in production blasting. With respect to improving breakage and fragmentation, it has been demonstrated that the delay interval between adjacent explosive charges should be less than the expected burden movement time. Similarly to reduce confinement between rows, delay intervals should exceed the expected burden movement time. The Hybrid Stress Blasting Model (HSBM) is a modelling framework that dynamically links an ideal and non-ideal explosives detonation code to a geomechanical rock model. This blast simulation tool is aimed at analysing the role played by different explosive formulations in fragmenting and/or damaging various rock types under different degrees of confinement. In the current framework, the rock behaviour under extremely high pressures and loading rates is calibrated from shock tests and the role of the explosive in fracture growth is accounted for and assumes a compressible fluid flowing through the explicit fracture network. The model is being developed as part of an international collaborative research project funded by a consortium of companies comprised of explosive and equipment suppliers and major mining houses. As part of the development and validation of the HSBM project, data from literature addressing the kinematics of the rock mass (ie burden displacement, face velocities and response times) has been collated and used to evaluate the current version of the code. A series of numerical experiments have been conducted with the view to: evaluate the response of the rock mass to changes in burden distance given by the impact of both stress waves and radial gas flow pressure;compare the modelling outcomes in terms of displacement, response time and face velocities to documented field observations; andcompare stress induced and stress/gas induced modes in terms of burden displacement outcomes. Results from these experiments have shown that in its current form the model is able to capture the trends observed and measured in practice. This is with respect to the simulation of burden displacement, response time and average face velocities for different geometries and charging conditions. The experiments have served as consistency checks which form part of an ongoing and comprehensive evaluation and validation of the HSBM code also aimed at addressing some of its current limitations.

Jan 1, 2007

By Whiten WJ

A method that allows data to be mass balanced and screen models to be fitted in a single step is described. The inclusion of several variables to describe the feed data in the fitting procedure allows a mass balance to be conducted at the same time as the fitting of the screen model. Analysis of Groote Eylandt Mining Company screening data has demonstrated that this method is ideally suited to applications where complete stream data are not available. Also, certain random fluctuations in screen model parameters arising from the fitting of consecutive mass balances and screening models are significantly reduced. A cubic spline function with fixed knot positions corresponding to particle sizes and variable (fitted) cumulative percent passing values is used to describe the feed size distribution. When the spline function is interpolated at the experimental feed particle sizes a fitted feed size distribution is obtained. This feed size distribution is then used as input to the screen model calculations from which product size distributions are generated. Since both feed and product size distribution data are used to minimise the residual errors between the observed and fitted stream size distributions, a mass balance is Conducted simultaneously with the screen model parameter fitting.

Jan 1, 1984

By Payne AR

The high cost of gateroad repairs and maintenance in U.K. longwall coalmining is a clear indication of the failure of permanent support systems to fulfill their prime function, i.e. control of strata movement. The main component of gateroad support is the pack, the design and materials of which have experienced an important development process during the last 10-15 years. More recently, research investigators have attempted to give a design basis to pack quality and dimension, and reference is made to two theoretical approaches. In the course of a current research programme based upon in situ monitoring, interim design recommendations have been proposed as a means of effecting improvement in support efficiency. Identification of characteristic deformation behaviour forms the basis of the recommendations made and the subsequent improvement in gateroad performance reported.

Jan 1, 1986

By Scott A

The object of most blasting operations is to destroy the insitu structure of the rock mass so that mechanical equipment can efficiently excavate the rock fragments. In achieving this objective the blasting engineer is also concerned with minimising damage to the adjacent rock which forms the mine structure relied upon to provide support. Damage to this "structural" rock is undesirable but usually occurs as a result of two distinct processes: ò readjustment of stresses around the excavation as a result of the mining process itself ò impact of vibration and high pressure gases from blasting operations. Gross damage to mine structures from either cause is observed as visible alteration to the appearance of the rock structure in the form of cracking, slabbing, back or over break and visible displacement. Recent work at the Julius Kruttschnitt Mineral Research Centre (JKMRC) has shown that significant reduction in the strength of a rock mass can take place well before the onset of these obvious signs of damage. It has been demonstrated that the effect of blast damage on the behaviour of the rock mass can be many times more prominent than the effect of stress redistribution. This offers the blast design engineer the opportunity to significantly reduce blast induced damage to rock structure by modifying blasting practices. This paper introduces the current JKMRC postgraduate research projects investigating the evaluation and control of blast damage.

Jan 1, 1990

By Lynce AJ

A method has been developed for the prediction 'of 'the- . performance of a multi-stage grinding=cyclone classification circuit of any degree of complexity on any ore for a wide range `of operating conditions, The-.method involves ;the. s` inu ation b'f the circuit on a digital computer by means of. matheinatical' models ":bf the"' individual units:, the. development of which is- also discussed'., At present, in order to establish 'the!'" charac'teristtics of they ¦ore- and the machines. in mathematical terms;. it is necessary to know'the performance of a , simpl,.e. ; system on tri.e ore - for! one known ,,feed rate and.fe.ed s,l-zing, analysis. ' ,Fiiither work on :the- separate identification 'of the terms defining the characteristics of the ore and the machines may permit the method to be, applied directly to the cj.4ta,derived from small scale tests on ores,

Jan 1, 1964

By L M. Lobato, J C. S Seoane, F J. Baars

The Carajßs Province presents several volcano-sedimentary sequences that comprise the Itacai·nas Supergroup. The rocks represent bimodal volcanism, and clastic and chemical sedimentation in relatively unstable basins subject to recurrent structural events with subsidence and volcanism. The Grpo Parß Group represents one of these sequences with mafic volcanic rocks that enclose discontinuous jaspilite lenses, with development of large high-grade orebodies (Fe >65 per cent). This unit is named the Carajßs Formation and presents peculiar characteristics compared to other iron districts in the world, thereby departing from the classic Lake Superior or Algoma iron formation types. Owing to the dense vegetation, lack of outcrops and harsh landscape, the structural analysis of the district can only be accomplished by combination of regional field work, detailed structural work on the open pits, and remotely sensed image interpretation, in this case Landsat ETM7, JERS-1 images and the SRTM digital terrane model. The regional trend of the several sequences of the area is approximately N-S and the structure is dominated by a flattened flexural fold system with axes moderately dipping WNW, intersected by several strike-slip faults subparallel to their axial plane. The Serra dos Carajßs represents an s-shaped synform-antiform pair, herein named the Carajßs Fold. This regional structure is partially disrupted by the Carajßs Shear Zone that divides it in the northern (Serra Norte) and the southern (Serra Sul) Ranges and also probably prepared the terrane with the development of pathways for mineralising hydrothermal fluids forming large high-grade massive iron bodies. Syntectonic granitic bodies played an important role in the structural evolution of the area as well. They caused localised ductile flattening deformation and thermal contact metamorphism in surrounding terranes. The Estrela pluton, for instance, was responsible for the discontinuity of the regional trend between the Serras do Rabo and Leste. The Carajßs Province is regionally the upper crustal product of a very shallowly eroded dome-and-keel geometry of Neo-Archaean volcano- sedimentary units intruded by syntectonic calc-alkaline intrusives and overlying pre-existing infracrustal rocks. The lithostructural data suggest continental-margin back-arc basin development and closure in an oblique collision belt, with N-S shallow crustal shortening, parallel to the inferred pre-existing strike of the stratigraphy.

Jan 1, 2005

SITUATED in the county of Manchcster, in Northern Eyre's Peninsula, the Iron Knob ore-deposits form the basis of the industry. These deposits are connected by the Iron Knob tramway to the port of Whyalla, aal miles distant, on the western shore of Speneer Gulf,and to-day another tramway is under construction to link up with the same port, a second group of iron ore leases known as Iron Baron, which is situated 18 miles south of Iron Knob. Fig. 1 indicates the geographical relationship of these three places, Iron Knob, Iron Baron, and Whyalla, which together comprise this field of the company's activities.

Jan 1, 1930

By Lennox A

In an attempt to increase underground productivity Coal and Allied has introduced a continuous haulage unit into it's Moonee colliery. A second unit is planned for Nallarah colliery in the near future. Both systems will be roof mounted or monorail type and manufactured by Joy Manufacturing Pty Ltd. The introduction of these machines is seen as a logical step in improving the efficiency of mining with continuous miners. This could be in conjunction with longwall mining in the rapid development of gate roads or, as in the case with these machines, as conventional development and extraction units. The advantages of the continuous haulage system are; Relatively low cost. 2 Ability to obtain high productivity in irregular or disturbed coal reserves not suitable for longwall mining. 3 Increased worker safety with the elimination of shuttle cars and the majority of trailing cables. 4 Increased productivity independent of soft or difficult floor conditions. At the time of writing the Moonee installation is 6 months old. The Nallarah machine is due for delivery March 1988.

Jan 1, 1988

The Wild Dog gold-silver-copper deposit represents a new ore-deposit type in Papua New Guinea. The telluride vein mineralisation is associated with a Tertiary caldera and has similarities with that from the Baguio district, Philippines, Vatakoula, Fiji, and the San Juan Mountains, southwestern Colorado. The deposit, discovered in July 1983, has negligible stream silt and concentrate anomaly, and a float-train limited to within 300m of the prospect. The comparatively recent exposure of the vein system may explain the limited stream expression of the deposit. At least three major veins occur in the deposit; the vein system strikes north- northeasterly, dips 78¦W, and has a maximum strike length of 1350m. Veins are enveloped by a wallrock dominated by an assemblage of quartz-illite-pyrite. Four types of silicification related to multiple vein filling events have been defined on the basis of field relationships, drill-core intersections, petrology and fluid inclusion study. To December 1986 a total of 22 diamond drill holes (2304m) and 40 reverse circulation drill holes (1833m) have been completed on the deposit, defining a 750m zone of interest. The upper 30m of the deposit is oxidised. Much of the high-grade mineralisation in both the sulphide and oxide portions of the deposit is restricted to ore- shoots which strike parallel to the overall vein structure and are vertical to steeply westward dipping. They are defined geochemically by the lg/t Au cutoff and geologically by the relative increase in the vein density of auriferous grey-black sulphidic silica, the final vein filling event. Metallurgical studies and the results of close-spaced drilling have demonstrated the very good repeatibility on duplicate assays, and the extremes of grade variability of mineralisation over very short distances. The good assay agreement on duplicate samples .s indicative of fine, dispersed gold.

Jan 1, 1987

By Lawrence L. J

The Australian Broken Hill Consols Mine, situated some 600 yd east of the main Broken Hill line of lode, is noted for its rich ores of silver. In contrast to the vast conformable orebodies of the Broken Hill field, the Consols lode occupies a narrow fissure dipping to the south west at angles increasing from 240 through to vertical and transgressing the strike of the metamorphosed country rock at an oblique angle. This feature, together with the abundance of calcite and siderite and the virtual absence of silicate minerals in the gangue, has led to its classification as an orebody of the Thackeringa type (King, 1953). Recorded production during the period 1890 to 1903 is given as 845,000 oz of silver and 20 tons of lead.The unusually rich silver values of the Consols lode were concentrated at the intersection of the fissure with beds of amphibolite, whereas in the adjacent schists and gneisses the lode became markedly impoverished. From the surface to a depth of some 120 ft extensive surface oxidation had occurred, resulting in the breakdown of siderite and its replacement by limonite and associated manganese oxides.Silver halides, dyscrasite, acanthite and partly oxidised tetrahedrite were the main silver minerals in this zone. With increasing depth the lode material gradually reverted to minerals representative of the hypogene zone.The only previous work specifically on the mineralogy of the Consols lode is that by Smith (1922), one time manager of the mine. His zeal as a mineral collector resulted in much valuable information being available on the distribution of the minerals. More recently, Garretty (1943) noted the...

Jan 1, 1962

By Y Li, L Zhang, G Li, S C. Dominy

Qiagong skarn iron (copper) deposit is located in Xietongmen County of Tibet, China (N 29¦52Æ14.9ö, E 88¦24Æ10.3ö). It is situated at the middle-western Gangdese porphyry copper-belt. Mineralisation is related to a Himalayan porphyry intrusion, with the mineralised body occurring at the contact zone between the Tertiary Takena Formation carbonate rocks and Himalayan monzonitic granite porphyry. The melt, melt-fluid and fluid inclusions were observed in early quartz, with most abundant fluid inclusions in quartz, calcite and garnet from the skarn. The geology and inclusion assemblage show a close relationship between iron (copper) mineralisation and a Himalayan porphyry intrusion. Based on preliminary inclusion studies, this paper discussed the characteristics, evolution of ore-forming fluid and affiliation to the Himalayan porphyry intrusion. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By E P. Donohue

Changes to water industry practice are required as a consequence of the Council of Australian Governments water reform agenda which binds all states and territories to a range of measures intended to drive new efficiency, sustainability, higher value use and proper provision for environmental needs. Queensland is implementing its reforms program through its water resource planning process, a legislatively underpinned program that provides for a new level of social, economic and environmental security. A water resource plan for the Fitzroy Basin has been finalised and its implementation plan, which details infrastructure operational arrangements for the basin, is due to be released later this year. The mining industry is a major contributor to the economy of the Basin, and although a comparatively minor water consumer, is now aligning its water use practices with the stateÆs maturing integrated resource management paradigm. This new culture presents both challenges and opportunities. Water reform in the Fitzroy basin is well advanced. The processes and institutional arrangements that have been developed are of significant importance to the aspirations of current and future minerals development. This paper outlines the current status of those reforms and the likely institutional framework for the near future. The paper also discusses how the reforms impact on the availability, access and security of water available to mining interests.

Jan 1, 2003

In process industries, time-dependent random fluctuations of raw material characteristics and mass flow rates in bulk material or pulp flows cannot be always prevented for different reasons, eg because of the geological situation (no uniform formation of the deposit) or/and because of technological reasons (segregation in bunkers or on stockpiles). Since a long time, there has been practical experiences that such fluctuations can have negative consequences, eg: ò fluctuations of the final products characteristics, ò higher expenditure for process control, and ò worsening of technological characteristics (recovery, sharpness of separation etc). In the literature, there can be found a lot of details as to, eg the improvement of the sharpness of separation in a jig in dependence on the raw material blending (Kubitza, 1981; Gathen, 1983) or the decreasing flotation recovery with increasing raw material characteristics fluctuations in iron and potash ore processing plants (Bubnova, 1978). Up to now, however, these consequences of random fluctuations, eg on the separation efficiency were not predictable theoretically. It could be shown by means of the general model for mechanical macroprocesses (Graichen, 1989), that the reduction of input fluctuations passing a blending facility can be calculated in this way. In this example, the steady state of the process is the wanted one, but, in general, the model is able to describe also non-steady states of the process regarded. On the other hand, the general model of mechanical macroprocesses has been used successfully for modelling separation processes, eg cross-flow and air classification (Molerus, 1969; Neesse, 1991; Senden, 1979; Tichonov, 1973). That is why it was tried to model the influence of input fluctuations on the separation efficiency, that means, the impact of non-steady states - as a consequence of random fluctuations - on a separation process. The models discussed in the literature are related nearly exclusive to the steady state of the process. The reasons for that lie in the (relative) simplicity of the models and the fact that the steady state is aimed at by means of blending processes under practical conditions - because of the advantages mentioned above. These models cited have proved to be superior to other models, since the basic general model for mechanical macropocesses makes possible the consideration of turbulence acting in the process unit and influencing the separation process essentially. This is valid also for modelling the turbulent cross flow classification, applied to mechanical classifiers and hydrocyclones, where the correspondence between the separation characteristics (cut size, separation sharpness) calculated and determined experimentally is much better than for other models.

Jan 1, 1993

By J Moncrieff, P Bellairs

The Black Star Open Cut is located immediately adjacent to the township of Mt Isa and is situated in the middle of extensive pre-existing infrastructure including two concentrators, two smelters, a wet fill plant and two shafts. At any one time there are in excess of 500 people working on the surface within an industry-accepted 600 m exclusion zone from Black Star blasts. Apart from the surface operations there are also the underground operations including the lead mine (closed in December 2005) and the Enterprise and X-41 mines that must clear for all Black Star blasts. The application of industry standard blasting exclusion zones (600 m) was risk assessed as imposing operationally prohibitive constraints which could cause significant business interruption due to the logistical challenges required to ensure that all personnel from surface plants were evacuated for each blast and potential for lost production whilst these personnel were not operating the plant. In was therefore an imperative for the blast exclusion zone to be reduced. This was achieved by the: use of a QA/QC team to ensure that relevant drill and blast implementation is within an acceptable tolerance (KPIs) from design; use of high-quality stemming material called HMR, which is a by- product of the concentrating process and is generally sized at -14 mm with very little fines; implementation of appropriate training and support to Black StarÆs own blast crews, reinforcing the need to achieve the designed amount of stemming in every hole; and provision of appropriate support from Black StarÆs management for additional resources to ensure that every blast achieves design within the KPIs but especially in high-risk areas. The blast exclusion zone was successfully reduced after monitoring the flyrock results from more than 176 blasts. Black Star Open Cut now maintains a minimum blast exclusion of 200 m in critical areas; however, general blasting currently uses a 250 m exclusion as this provides additional risk management whilst still minimising the logistics associated with clearing and securing the slightly increased area.

Jan 1, 2007

By Biao Q, Mizuta Y

Thermal constants such as thermal con- ductivity and thermal diffusivity of rock and coefficient of heat transfer of airway wall are the most important characteristic values which decide accuracy of prediction calcula- tion. However, quality of rock is not homoge- neous and water content in rock varies with location and so, a method for in-situ measure- ment of thermal constants must be taken in. The method developed by us is to measure in- situ rock temperatures at two different depths from airway wall. It is simple and we found its accuracy is good enough in the engineering Sense.

Jan 1, 1988

By W Mez

The German mining industry uses different residues for backfilling and stowing. A hydraulic pipe conveying technology for these materials has shown advantages for the transportation into the mine. Pipeline conveying systems are able to bridge long distances, they save room within the underground workings and they save staff and costs. Absolutely necessary for successful use of the hydraulic conveying technology is the knowledge about the unusual non-Newtonian flow properties of solid/liquid mixtures like pastes and slurries. The flow resistance of these materials cannot be described easily by one viscosity. Owing to a yield point and a pseudo-plastic behaviour the viscosity changes with the shear rate and with the streaming velocity inside the pipe. Also these flow behaviours depend very sensitively on the liquid/solid-ratio, often so dramatically that gravimetric or volumetric dosing equipment is not in a position to control the production of backfill pastes. Quality changes of the solid raw materials (particle size distribution, density, mineralogical composition) lead to additional difficulties. The first experiences with hydraulic backfilling plants were troubled by plugged pipes, a bad backfill quality caused by unnecessarily high water content and high costs for chemical binders to solidify the backfill. The installation of viscosity controlled paste production leads to success with the hydraulic backfill technology. A development of the DMT, a bypass pipe-viscometer, has been the key technology. The system is able to analyse on-line, difficult, sticky and abrasive substances and determine their non-Newtonian flow properties. Because the system measures real physical values it is in a position to pre-calculate process relevant parameters like the pressure drop of the backfilling paste in the conveying pipeline. Newer types of the viscometer system also measure the slurry density and calculate its composition. These systems have proven a success controlling backfill paste production plants. They offer a secure prevention of pipeline plugging and a production of high quality backfill pastes with a water content as low as possible.

Jan 1, 1998

Two main aspects need to be considered when analysing a potential petroleum development project. Firstly, an estimate of the recoverable reserves must be made, and in many instances, these reserves must serve as collateral to finance development if outside capital is required. Secondly, the likely production profile and cash flow has to be established, and this cash flow then must meet debt service require- ments and in addition generate the required profits. In making these crucial deter- minations, the impact on the project of a wide variety of risks has to be analysed. A computer model, which represents the project in its entirety, is a great aid in determining project viability. Such a model requires imput from geologists, engineers and economists, and interpretation of the model must also be a joint effort. Communications, and inter react ion amongst individuals and disciplines is essential if the best answers are to be obtained

Jan 1, 1983