Search Documents

By Just J, Nguyen G, Dunn J. G, Graham J

A sample of pyritic gold concentrate was investigated by wet chemical and electron optical techniques. Sub-samples were roasted in a laboratory scale fluidized bed roaster in the temperature range 400-700¦C. The calcine was characterised, and cyanide-leached using a standard bottle rolling test. Gold extraction efficiencies varied with roasting temperature. At temperatures of 400 and 450¦C gold ex- tractions of less than 40% were achieved, but between 500-700¦C the extraction had increased to 93--98Z. The surface area of the calcine varied with roasting temperature, reaching a maximum at 500¦C. There was no correlation between the surface area of the calcine and the efficiency of gold extraction.

Jan 1, 1987

By J M. F Clout

The low-grade clay-rich -1.0 mm fraction of fine iron ores have often proved difficult to upgrade and capital intensive to process when using traditional wet beneficiation technology including single or two stage hydrocyclone desliming, wet high intensity magnetic separation (WHIMS), spirals and final dewatering using fine screens. Very fine (<0.010 mm) clay-rich slimes simply follow the water split to the hydrocyclone underflow where it often impedes the subsequent processing performance of any downstream spirals and can result in troublesome direct dewatering of hydrocyclone underflow. The -1.0 mm fraction in goethitic iron ores is typically considered as waste. A new two-stage wet gravity separation flow sheet, referred to as the ædesandÆ process, has been designed to overcome these issues for the upgrading of low-grade clay-rich goethitic or hematite-quartz fine iron ores. The desand process is designed to treat the -1.0 mm range from -8.0 mm natural fines, to recover a -1.0 +0.038 mm higher-grade fraction by rejecting to tailings any low-grade clay-rich ultrafines and low density sand-size fine chert/quartz gangue and shale.The desand process consists of wet screens with a nominal 0.7-1.0 mm cut point which direct the undersize to hydrocyclones. The hydrocyclone underflow is then fed to upcurrent classifiers where the classifier middlings is sent to spirals and classifier and spirals concentrates are then dewatered using vacuum belt filters or fine screens. The three product upcurrent classifier is employed to further deslime the hydrocyclone underflow, producing firstly a coarse final concentrate, and then a deslimed middlings for feeding to spirals as well as a 0.100 mm clay and fine quartz or banded iron formation (BIF) sand in final overflow for feeding to the residue thickener. The upcurrent classifier middlings provides the spirals with a significantly cleaner feed material than traditional methods, with the end result that the spirals do not silt up with slimes and therefore can continue to run at their optimum. The upcurrent classifier and spirals form a complimentary pair, with the upcurrent classifier better able to send coarser, acceptable grade particles to concentrate and fine slimes to tailings whilst allowing the spiral to better reject coarser, subgrade low specific gravity particles. Test results for the Mayoko-Moussondji iron project, Republic of Congo, using upcurrent classifier-Wilfley Table (simulating spirals) gave acceptable mass recovery from run-of-mine (ROM) and Fe recovery from hydrocyclone underflow for HEMCOL (6.2 per cent mass recovery from ROM/43.1 per cent Fe recovery) and HEMBIF2 (5.1 per cent mass recovery from ROM/22.3 per cent Fe recovery) mineralisation types. The desand process also enables improved dewatering of -1.0 +0.038 mm product from a clay-rich plant feed.A number of new wet plants in the Pilbara use the desand flow sheet including FMGÆs Cloudbreak and their two Christmas Creek plants. Many potential new applications are being explored, with new iron ore plants in India as well as those being proposed for West Africa. Operational experience has highlighted the importance of providing clean process water to the upcurrent classifiers as well as ongoing design improvements including increased wear life, reduced maintenance and enabling a more steady feed rate to spirals.CITATION:Clout, J M F, 2013. Beneficiation of fine iron ores using the desand process, in Proceedings Iron Ore 2013 , pp 337-348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Mines in the future deliver a paradigm shift in the way mining, material handling and processing are performed, unlocking significant value through production efficiency, flexibility and lower costs and enabling substantial safety and environmental benefits (V Schweikart). Mines in the future are highly productive, with low production costs and are significantly safer. They operate with a skeleton crew and use intelligent systems that fuse information from field instrumentation and other sources to generate the most efficient operating environment. Automated systems are seamlessly integrated across the mine and across the corporate enterprise. Geological models, long-term and short-term plans create optimised production schedules, suitably generated by the mine simulator. Production schedules are shared with the operations management system for deployment mainly by remotely operated and autonomous equipment. As the schedule is implemented, information is collected and shared with various plans, schedules, models and optimisation programs. This production environment is managed in real time from a æCentral Operations CentreÆ and it is visible across the business providing fast and accurate information about productivity, machine condition and environmental conditions. Central Operations Centres also house teams of subject matter experts that monitor and manage the mines and are able to communicate directly with the skeleton crew in the field. Constraints across the production line are displayed and managed appropriately from this location to maximise throughput. Maintenance is interactive and predictive. Reliability specialists in Central Operations Centres monitor the status of machinery and equipment and adjust maintenance plans and strategies to suit. Mining businesses rely heavily on knowledge workers û people with considerable knowledge and learning û and by manual workers. This new knowledge workforce is a team of associates rather than of bosses and subordinates. Field experts become leaders with tremendous autonomy regarding their work. The former line hierarchy becomes a support structure, intervening only in extreme emergencies; instead of giving orders, they are now removing barriers, expediting resources, conducting studies and acting as consultants.

Jan 1, 2009

By R C. Owen, M A. Ward

The paper describes the application of New Zealand's environmental impact assessment procedures to a proposed gold and silver mine in the North Island of New Zealand. The project is described and a summary is provided of the statutory permits or consents that are required prior to operation of the project. Emphasis is given to the requirement for environmental impact assessment and the preparation of a formal environmental impact report. The company's approach to impact assessment is described, with examples of how this assessment and the identification of management alternatives influenced the engineering design of the project. This paper was prepared as a contribution to a working session of the International Association of Impact Assessment VII Annual Conference, July 1988.

Jan 1, 1988

Seven papers have been reviewed and in this session. Broadly they can be grouped into three categories as follows: A Chemical Characterisation of Mine Waters Miller & Murray - Prediction of Time Dependent Factors in Acid Mine Drainage Jeffrey et. al. - Sulphide Oxidation in Pyritic Overburden; A Controlled Leach Column Study Sheridan et. al. - The Effect of Ore Type, Depth, and Leach Time on Cyanide Species in Column Tests using NaCN Leach Solutions B Mine Water Treatment Management Gilchrist & Hunt - The Recovery of Water from a Colloidally Stable Kimberlite Suspension Chapman, et. al. - Treatment and Utilisation of Hilton Mine Water

Jan 1, 1988

Incremental sampling is defined as a solution to fight segregation, the theory is demonstrated and theoretical and practical aspects are discussed. The number of increments necessary for successful sampling is discussed. As an application, riffle splitter division is reviewed.

Mar 1, 2010

By Reilly SY, Green TH, O&apos

Alkali feldspar meggacrysts are commonly found (with aluminous clinopyroxene, kaersutitic amphibole, titanomagnetite, ilmenite and apatite, and more rarely with zircon and corundum) in alkalic basalts and their derivatives as discrete crystals and fragments. They are commonly euhedral or subhedral and may be up to 15 cm in size. Their occurrence has been reported from many localities around the world, e.g., Africa, Antarctica, eastern Australia, eastern China, East Fife (Scotland), Eifel (Germany), Massif Central (France), Mongolia, New Zealand, New Mexico (USA) and Siberia (USSR). These megacrysts are relatively homogeneous and belong to the Na-rich anorthoclase group, although Kutolin and Frolova (1970) called them sanidine due to their monoclinic nature. The majority of megacrysts have a molar orthoclase content (Or%) between 20 and 30 (Fig.1). These anorthoclase megacrysts possess a high degree of disorder, with the structural state belonging to the high albite-high sanidine series (Hoffer and Hoffer, 1973; Chapman, 1976).Published interpretations of the origin of anorthoclase megacrysts fall into the following two categories: either (1) Anorthoclase together with the associated pyroxene and amphibole crystallized from basaltic magmas as phenocrysts (cumulate phases) at high pressure and the present host basaltic rocks are the parent magmas for the anorthoclase megacrysts (Binns,l969; Binns et al. 1970; Kutolin and Frolova, 1970; Hoffer and Hoffer, 1973; Laughlin et al. 1974); or (2) Anorthoclase probably crystallized from a more evolved liquid at relatively lower pressure and was then picked up and carried to the surface by a later

Jan 1, 1990

Sixty years after its inception, after an alternation of periods of admiration and rejection by the industry, Sampling Theory can now be seen as going through its golden age. A brief history of its successive transformations and progresses achieved by its author, Pierre Gy, and his followers, reveals the theoretical as well as practical difficulties that had to be vanquished to reach this point. Its current level of acceptance and corresponding trends are discussed and illustrated, with an insight on its increasing real role in the industry and future prospects for its further development.

Jan 1, 2008

International tenders for contract mining opportunities require the Contractor to make an assessment of risk for an operation with a life span of up to twenty-five years usually based on data made available by the Client. This paper seeks to address how the Contractor assesses the data and quantifies the risks associated with the project. The areas of risk are common to most projects, but in the--Lontractor's case, risk assessment is carried out on the Client's data base and within a compressed time frame of usually less than six months. Incorporation of that risk assessment into the contract documentation is also discussed. Practical examples are given in a number of areas.

Jan 1, 1986

By Jones TRP

The Agnew Nickel Mine has a short his-tory of mining activities. However it has experienced a large variety of ground support problems. These problems relate to geological, hydrological, geomechanical, structural and mining techniques. The majority of the prob-lems occur in other underground mines. How-ever the large serpentinite hosted ore body which contains over 80% of the ore has prob-lems rarely encountered in other mines. Sol-utions to the problems are only being gained by understanding the factors creating them.

Jan 1, 1985

The fluorspar deposits at Okorusu, Namibia are closely related to an alkaline igneous ring complex of late Cretaceous age (125¦7 Ma). The fluorite ores consist of relatively fine-grained purple replacement fluorite and subsequent coarser-grained purple and green vug-filling fluorite crystals. Homogenisation temperature measurements for 38 primary fluid inclusions shows that main stage purple to green fluorite crystals were deposited over a temperature range from 166¦C to 144¦C, and minor late yellow fluorite was deposited at lower temperatures from 132¦C to 128¦C. Homogenisation and freezing temperatures measured for 18 primary fluid inclusions shows that the fluorite-depositing fluids were less saline than Mississippi Valley-Type (MVT) ore fluids and overlap the lower temperature range of fluids that deposited epithermal ore deposits. Mining in three open pits (A, B and C) at Okorusu has gradually provided exposures which reveal that the fluorite orebodies have been emplaced primarily by the preferential replacement of carbonatites. Evidence for the replacement of carbonatite includes: replacement remnants of carbonatite within the fluorite ores; goethite pseudomorphs after the carbonatite minerals, pyroxene, pyrrhotite and magnetite, which are disseminated in the fluorite ores; andpartial replacement by fluorite of a large sill-like carbonatite body in the A pit. Electron microprobe analyses of minerals in unreplaced portions of the carbonatites show that their mineralogy consists of titaniferous magnetite, diopside pyroxene, apatite, biotite and calcite. Magnetite contains 6.97 per cent to 10.46 per cent TiO2, averages 8.44 per cent TiO2, and has an average V2O3 content of 0.35 per cent. At high magnifications under the scanning electron microscope (SEM), the magnetite shows abundant fine ulv÷spinel exsolution lamellae arranged in a cloth texture. Apatite contains moderately high fluorine contents that range from 3.21 to 5.0 per cent and average 4.2 per cent, and apatite crystals range in total rare earth oxides from 1.7 per cent to 2.61 per cent. Pyroxenes in the carbonatites are iron-rich diopside, and they contrast to pyroxenes in the fenites that are aegirine-augite. All of the microprobe analyses for mica crystals in the carbonatites give biotite compositions. Microscopic examination of fluorite concentrates from Okorusu provides mineralogical information important to the resolution of beneficiation problems. Fluorite ores that are related to carbonatites are typically accompanied by phosphorus benefication problems. The cause for the presence of phosphate in some of the Okorusu fluorite concentrates is a function of the presence of binary locked fluorite-apatite particles. The fluorite ores have also replaced marble locally in the A pit, especially along the A band in the B pit, and dominantly in the orebody proposed for the new C pit. Those ores are characterised by fine grain sizes, faint remnant bedding, lack of carbonatite mineral pseudomorphs and local presence of remnants of unreplaced marble. Concentrates derived from those fluorite ores are devoid of phosphorus, but commonly have elevated silica contents due the presence of free quartz. Carbonatite and marble were preferentially replaced by fluorite because the calcite was readily soluble in the presence of the fluorite-depositing fluids and the dissolution of calcite provided calcium for the formation of fluorite. 

Jan 1, 2008

In the 25 years since Broken Hill's 75th Anniversary which was marked by an Australasian Institute and Mining and Metallurgy Conference in Broken hill, there have been some significant changes in the role of mines inspectors. This paper updates the information given by the then Chief Inspector of Mines, J.H. Burford, to that 1968 Conference, with an emphasis being placed on mines inspection, although it also reflects changes to mining legislation and regulatory bodies.

Jan 1, 1983

Forty two new apatite and zircon fission track analyses on the Kubor-Marum-Bena Bena area of northern Papua New Guinea severely constrain the timing of tectonic events and hence the tectonic models for New Guinea, particularly arc-continent collision. In addition, the data can be analysed regionally in terms of known and assumed lithospheric fault zones inferred to control mineralisation (eg. Corbett 1994; Kendrick et al 1995; Hill et al 1996) to determine reactivation of these zones. When combined with the new kinematic plate models for the evolution of New Guinea (Hall 1997) there is the potential to predict likely zones of mineralisation. The low-medium grade? Palaeozoic rocks of the Bena Bena terrane yielded a zircon fission track age of 17 Ma, indicating the time of cooling below 200¦C. The age is consistent with `the shift, at about 16-18 Ma, from volcanolithic sediments to mixed provenance sediments rich in quartz and metasedimentary lithic fragments in the southern Finisterre Ranges (Abbott et al. 1994). This shift was recorded in the Sukurum Formation, which ranges in age from Middle Miocene to Pliocene with quartzose and metasedimentary grains in all samples. Although recording rocks at temperatures of 200¦C and hence depths of ---5km, the 17 Ma age suggests the Bena Dena terrane was rapidly cooling at that time due to uplift and erosion, supplying metasediments to the southern flank of the Finisterre Range, currently 100 km to the east. Significantly, the Middle Miocene Akuna Intrusive Complex, dated 14-17 Ma by Page (1976), lies almost entirely within or adjacent to the Bena Bena terrane. Potentially the uplift, erosion and cooling of the terrane at 17 Ma may have been caused by the rising plutons. If so the 800 sq km exposure Akuna Intrusive Complex at the SE end of the Bena Bena terrane may have been the focus of uplift and supplied the metasedimentary detritus to the Finisterre Range. This suggests that the Finisterre Range was not far removed from the Bena Bena terrane, perhaps less than the 200 - 400 km indicated by Abbott et al (1984). The Akuna Intrusive Complex probably resulted from subduction of the Solomon Sea Plate beneath the PNG margin. In order for the subducted slab to reach depths of -100km below the area to facilitate partial melting and plutonism (Hamilton 1994), subduction probably commenced 3-5 Ma Ma before plutonism, ie at or prior to 20 Ma suggesting a significant change in the tectonic regime at -20 Ma, perhaps related to collision of the Solomons - Ontong Java Plateau collision (eg. Hall 1997). The main result to emerge from the 28 apatite fission track analyses is that the whole of the study area underwent rapid cooling due to uplift and denudation in the Late Miocene, mainly between 7-10 Ma. Results from several samples indicate that they were not totally overprinted prior to uplift indicating maximum burial of -3 km in the Middle Miocene, assuming normal temperature gradients. The burial is less if higher gradients are assumed, allowing for Middle Miocene plutonism. The Late Miocene cooling in the Mobile Belt agrees well with the Pliocene to Recent cooling in the Fold Belt to the SW, interpreted to be due to uplift and erosion associated with fold and thrust deformation of the Miocene Limestones (Hill & Gleadow 1989). This timing relationship suggests, that compressional deformation in the Mobile Belt occurred in the Late Miocene, at 105 Ma, and that the deformation migrated towards the undeformed foreland in the southwest in the Pliocene, at 5-2 Ma. The regional Late Miocene uplift and denudation in the Mobile Belt is also consistent with that postulated by Crowhurst et al (1996; 1997) for northwest PNG, although they considered the event to have occurred mainly from 8-5 Ma. If so, then the uplift and denudation may have been migrating from east to west as well as to the south into the Fold Belt. These timing relationships place significant constraints on tectonic models for the area, indicating that the major compressional pulse in PNG commenced in the northeast at -10 Ma and migrated to the southwest and west in the latest Miocene to Pliocene. This suggests that the initial arc-continent collision and associated shortening occurred in the Late Miocene around -10-12 Ma. This immediately followed intrusion and cooling of the Akuna Intrusive Complex at -17-14 Ma and the Bismarck Intrusive Complex at -12.5 Ma (Page 1976), indicating a linkage between the end of plutonism and the start of compressional deformation. The timing is consistent with the observation of Hamilton (1994) that in areas of subduction `the common regime in overriding plates is extensional and leading edges are crumpled only in collisions. This suggests that the Middle Miocene magmatism in northern New Guinea occurred during extension above a subducting slab and was terminated by Late Miocene arc collision and resultant compression commencing at -10-12 Ma. In general, these data indicate that the acme of denudation and cooling in the Mobile Belt was in the Late Miocene, with relatively little denudation there since. In contrast, Hill & Gleadow (1989) found that the peak of denudation in basement outcrops in the Fold Belt was in the Pliocene at -4 Ma. However, in this study some samples from the Mobile Belt yielded Pliocene ages or high

Jan 1, 1997

Commercial explosives range from pure emulsions to pure ANFO, with blends of these providing interesting alternatives: energy is often adjusted through addition of aluminium, or the control of density. The energy rating of explosives is derived chiefly from detonation codes, which are used to derive expressions for the internal energy change of the detonation products as they do work under expansion. While all codes used for this purpose work on the basis of Ideal detonation, it is common knowledge that commercial explosives operate in the Non-Ideal domain, which affects the mode of energy delivery to the environment. However, since Ideality represents the foundation from which actual performance evolves, it is valuable to examine the intrinsic energy release of a formulation before attempting to understand the influence of Non-Ideality. In examining the Ideal pressure profile of fundamental formulations, remarkable correlation has been found with field performance, and this increases understanding of the influence of various formulation modifications, especially in regard to the stage at which energy is released, and the effect on rockbreaking. This work has emphasised the value of attempting to understand and define better the non-ideal detonation process.

Jan 1, 2001

By M R. Davidson, M P. Schwarz

A model for column bioleaching is investigated to identify and understand aspects of bacteria in bioleaching applications, which have implications in heap bioleaching operations. The model is used to simulate scenarios that would otherwise be time consuming to perform experimentally. This study uses a model of bacterial transport and attachment/detachment to ore particles, with a bioleaching model for the depletion of a copper-sulfide, also accounting for liquid and gas flow and gas/liquid oxygen mass transfer. The model includes aspects such as oxygen and ferrous ion consumption, coupled with leaching of a copper-sulfide via the shrinking core model. The model is used to investigate how the rate of leaching is affected by the bacterial concentration in the columns, by the bacterial regeneration of the leaching oxidant ferric ions. The model is also used to assess the impact of oxygen limitation and inoculation method on the copper leaching. Some comparison of the model with experimental data will be shown.

Jan 1, 2004

By W R. Adamson

"Optimisation of drill and blast design and engineering can deliver a significant positive impact on the profitability of any mining operation; however, true engineering of the blasting process is less common than might be thought. The paper that follows explores this gap and suggests a process control-based approach to the challenge.The concept of applying modifications to drill and blast designs in order to achieve efficiency improvements in downstream mining processes is far from new. However, the author suggests that the practical application has become less than rigorous in a number of different sectors of the mining industry in a wide range of countries.There is a common tendency for the design process to become simplified to the point where the objective is merely the communication of instructions to field implementers (drillers, explosive suppliers, blasters, etc). In effect ‘design’ often degrades to ‘cut and paste’ with consequences that vary from mild to critical, with respect to the profitability of the business.Engineering of the drill and blast process involves the design function, not on a one-off basis but rather as a component of a more complete cyclical process that includes a statement of objectives, a design based on a suggested hypothesis, field measurement of results, comparison with the target ‘set point’ and the application of control measures followed by new measurement, including interpretation of the results in financial terms.When applied in this fashion, engineering provides practitioners with the means to optimise the drill and blast impact on the full spectrum business result of the mining activity.These concepts are discussed with reference to a surface gold mining operation applying run-of-mine heap leach extraction. Engineering optimisation by adapting process control and measurement techniques is demonstrated to be a key component of the solution set applied to generate enhanced operations productivity and stakeholder value. It is shown that a combination of rigorous measurement, model calibration and hands-on quality assurance/quality control facilitates the creation of a road map to profitability, stressing the need to consider economic trade-offs between operational expense (investment) and measurement of enhanced value (return on investment).The process, however, does not cease at this point. Implementation of true design practices, incorporating innovation and discipline in implementation or execution can drive the process to deliver demonstrable, technically validated outcomes. Furthermore, these technical results can be related to financially quantifiable impacts. However, this accomplishment does not guarantee that these gains or savings will reach the bottom line of those mining, quarrying and construction companies that begin the process with such high hopes.CITATION:Adamson, W R, 2015. Application of engineering discipline and a full-process optimisation focus – productivity to profitability without profuse pruning, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 3–12 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 24, 2015

Current models for the origin of banded iron-formation (BIF) derived in situ iron ore deposits assume that the typical chert and iron oxide banded BIF is the primary rock from which enriched iron ore deposits arise by the selective leaching of quartz and the residual accumulation of the iron oxides. Weathering extends to the base of all the hematite deposits of the Hamersley Province, which lie within the saprolitic weathering zone, as shown by the preservation of the primary textures, and are overlain by a hydrated goethite zone representing the solum. Since groundwater typically contains dissolved silica, derived from the hydrolysis of silicate minerals, greatly in excess of the saturation solubility of quartz, it is incapable of removing quartz from below the watertable, and quartz is preserved in all saprolites derived from quartz bearing rocks. Quartz may be dissolved in the solum due to the influx of meteoric water having little or no dissolved silica, but soil-forming processes that dissolve quartz likewise alter the oxides by hydration and transposition with consequent destruction of primary textures, and there is no suggestion of soil-forming processes having produced the deposits, which typically extend to considerable depths below the water-table. A characteristic feature of the typical hematite orebodies is the unaltered nature of the iron oxides in the ore compared to those in the adjacent cherty BIF. Although the solubility of ferric iron at >10 ppb is much less than quartz, any process capable of dissolving the huge volume of quartz must also affect the iron oxides, but evidence of this is completely lacking in most ore deposits. Hydrothermal alteration at Koolyanobbing in the Southern Cross Province affects both cherty BIF and ore, and clearly shows equal mobilisation and recrystallisation of hematite within quartz/hematite veins and in the surrounding cherty BIF, which shows no evidence for the selective leaching of quartz. Similarly, any metamorphic process capable of removing all quartz from BIF would leave characteristic evidence in the remaining oxides. However, a hydrothermal process may account for at least portions of certain ore deposits, in which the chert bands have been replaced by carbonates at comparatively low temperatures, to produce a quartz-free magnetite/ carbonate rock that is readily upgraded to high-grade ore by supergene dissolution of the carbonates. This process is interpreted to have formed high grade ore at Mt Gibson, Koolyanobbing æAÆ Deposit and Mt Tom Price North Deposit. In addition to carbonate replaced cherty BIF at Mt Gibson in the Murchison Province, there are extensive sequences of magnetite BIF without chert bands, and this chert-free facies of BIF is interpreted as the precursor to the majority of in situ hematite ore deposits, through oxidation and weathering of magnetite and iron silicate and carbonate minerals. The world-class martite/microplaty-hematite deposits of the Hamersley Province are a special case of BIF-derived iron ore deposits that were initiated during the Proterozoic era. Evidence from overlying Wyloo Group conglomeratic horizons containing clasts of Hamersley Group BIF indicates that microplaty-hematite formed within the clasts before deposition, and that Proterozoic subaerial oxidation and weathering of uplifted Hamersley Group formations produced the microplaty-hematite in both chert-free and cherty BIF.

Jan 1, 2002

By Shklyar FR, Bokovikov BA, Gordon YM, Scherbatskii VB, Yaroshenko YG, Shvydkii VS

The paper presents, for the first time, a complete mathematical model of the flow of gases in packed beds which describes the processes of gas-mechanics in iron blast furnaces and other shaft type smelting units. Good correlation between calculated and experimental results was obtained confirming the adequacy of the model. It is shown that the uniformity of gas distribution is related to the tuyere size and the extent of its protrusion into the furnace and that these variables may be used to regulate gas distribution across the furnace diameter. It is also concluded that furnace height has no significant influence on gas distribution. The necessity for a mathematical description of raceway phenomena has been experimentally proved. Conclusions from theory are shown to have profound implication to furnace design and operation.

Jan 1, 1975

By I Y. Maslov, S A. Gorinov

It was demonstrated that the stable propagation of the explosive process is possible in low-density emulsion explosives (EEs) obtained through mixing of emulsion with a significant amount of expanded polystyrene (or other similar) granules. Such a process takes place in the form of a detonation-like wave of emulsion drops in explosive gas streams flowing out of the high-pressure area of the reaction zone.Chemical reaction in such EEs takes place in the form of surface combustion of emulsion particles interacting with the gas stream.A method was developed for determining parameters of decomposition of low-density EEs, and it was demonstrated that a gradual pressure increase takes place in products during the explosion of such EEs.The performed analytical research allowed low-density EEs (obtained through mixing of emulsion with a significant amount of expanded polystyrene) to be recommended for smooth blasting.Industrial-experimental blasts at quarries of Ural and Siberia, with extreme positioning of sides and using low-density EEs, have confirmed the viability of the recommendations given.The obtained results are useful in the advancement of smooth blasting technology using low-density EEs.CITATION:Gorinov, S A and Maslov, I Y, 2015. Physical and technical evaluation of possibility using low-density explosives in smooth blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 555–564 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Johnson N. W, Manlapig E. V, Alexander D. J, Franzidis J. P

The importance of the froth region on flotation performance is often emphasised in the literature. It is well-known that decreasing froth depth or increasing air flowrate results in increasing cell recovery at the cost of lower concentrate gra

Jan 1, 1997