Search Documents

By Dugan K. J

Mine operators are currently in a situation where market forces are acting to reduce profit margins and at the same time, regulatory bodies are insisting on improved mine safety and stability. This means that ground support must be made more cost efficient while maximising operator and equipment safety.A key aspect of ground support efficiency is the 'in the ground' performance. This paper discusses the factors that influence the way rock bolts and cable bolts perform. It highlights the need to know how support efficiency varies in different ground conditions.

Jan 1, 1992

By Freeman NV

The concept of an in stream analysis probe was developed at The Zinc Corporation (now Z.C. Mines) in the late 1960's and commercialised quite rapidly, by Phillips and then AMDEL, as an alternative to the established centralised systems (Courier, etc.). The developments which have taken place since that time are reviewed and current procedures and performance are described. An audit of the system, recently undertaken by AMDEL, has highlighted areas where improvements can be made. In 1988 the ISA system will become an integral part of a substantially upgraded process control system.

Jan 1, 1988

The occurence of high silver values in the oxidised zone of the main lode at Broken Hill is well known as a large factor in achieving the early fame of Broken Hill, and the minerals of this zone form a long list, which has been tabulated by G Smith*, and includes...

Jan 1, 1926

By Weller KR, Restarick CJ, Stewart PSB

Following a detailed assessment of concen trator performance at Broken Hill South Limited which was reported in a previous paper, the fine grinding section was changed from a parallel arrangement of the two grinding circuits to a series arrangement, and the concentrator per- formance re-assessed. The change to series grinding had virtually no effect on the actual or potential capacity of the circuit to make a final product with 80% passing 100 mesh. However, the fresh flotation feed contained significantly less +150 mesh lead and +65 mesh zinc (material which was shown to float poorly), without an increase in the quantity of poor-floating ultra-fine lead and zinc. From the size-by-size flotation recovery data, it was shown that overall recoveries of both lead and zinc were approximately 1% higher than they would have been without this change in size distribution and it was concluded that this was a direct result of the change in grind- ing procedure.

Jan 1, 1972

By Dixon D. R, Sparrow G. J

Pressure leach liquors from the pressure oxidation of a bulk flotation concentrate prepared from a complex Cu-Pb-Zn sulphide ore were treated to remove iron, either by pressure oxidation (the Hematite process) or with particles of magnetite (the Magnetite process), followed by cementation of various metals with zinc dust to obtain a purified solution from which zinc was electrowon. Satisfactory iron removal was achieved by both processes after neutralisation to pH 4.5 or 5.5. Pressure oxidation of the liquor at 200¦C and 690 kPa oxygen overpressure, conditions similar to those of the Hematite process used in the zinc industry, resulted in the precipitation of the iron as hematite. With the Magnetite process, an iron hydroxide was precipitated onto magnetite at atmospheric pressure and ambient temperature and removed by a magnetic separation step. The performances of both these processes for the removal of iron are compared. It is concluded that the Magnetite process offers considerable cost savings. Other impurities, in particular arsenic, were also removed with the iron in both processes. Cementation at pH 5.2 and 85-90 ¦C with 3.5 g/L zinc dust reduced the levels of copper, cadmium, and nickel to a satisfactory level and subsequent electrolysis in a laboratory cell gave an acceptable deposit of zinc.

Jan 1, 1989

The Rosebery Mine on the west coast of Tasmania is a world class polymetallic base metal deposit, containing six major minerals: galena, sphalerite, chalcopyrite, gold, silver and pyrite. This resource has been exploited for nearly a century, yet a reliable estimate of the reserve continues to present a challenge.Over the past twenty years, the operation has changed from relatively low productivity cut and fill timber-support scraper mining, to higher productivity bulk mechanised open stoping. At the same time, economic constraints have changed and grades have fallen, which have increased the pressure to refine the resource/reserve estimating processes. This paper compares the restrictions of the polygonal section method of the past with the advantages of a kriged block model. The limitations of Mine Call Factors, the problems involved in converting decades of diamond drilling data on paper into a computer data base, and the effect of this new methodology at Rosebery, are described.

Jan 1, 1990

By Yin J, Sun H

A new technology has been introduced - the use of the High-Water Solidifying Material for providing pumped roadside supports to maintain a roadway for re-use in longwall retreating. As a gob edge support, its initial use at Hebi No. 1 Colliery was successful, providing acceptable performances in support and control of convergences and lateral closures of the gob-edge roadways. This acceptability applied to both first use and re-use when the roadway became a gateroad for the adjoining longwall, remaining stable throughout the associated loadings and convergences. The technology promises economic and social benefits.

Jan 1, 1992

By Dight P. M

The challenge of narrow vein mining is to produce ore with as little dilution as possible, at the least cost -commensurate with the increasing degrees of safety being demanded for mine workers by the modem 'duty of care' legislation. Geotechnical factors play an important, if not overriding, role in these areas. The geotechnical factors cover the complex interaction over a period of time, between the in situ and induced rock stresses, rock structures, rock mass strength and the cable, rock bolt and other ground support members. In the Archaean schist belt areas where many of our narrow vein mines occur the pre-mining in situ rock stresses are commonly significantly higher than the overburden stresses. These are concentrated in areas beneath previous open pits and may be highly concentrated in the pillars and abutments of stopes on narrow veins. The presence of high in situ stresses may be suspected from the appearance of drill cores and underground development long before they become sufficiently concentrated by mining to cause damage or bursts. These initial indications are discussed and modem low cost methods of stress measurement are described. Practical and quick methods of analysing the stress redistribution around scopes and other underground excavations are now available and guidelines for interpreting them in terms of rockmass characteristics, stope stability and support requirements are developed with the object of increasing safety, whilst reducing overall costs and dilution.

Jan 1, 1993

Saxonvale mine is a multi bench open pit coal mine developed to its Stage I capacity of 1.75 Mt/y of run of mine coal. Detailed engineering studies for the mine commenced in April 1980, approval to proceed with the development was received in July 1980 and first coal shipments were made in April 1982. The engineering and project management of the mine development was carried out by BHP Engineering. This paper outlines the design and site administration for the development and describes both the organisation structure and the control and administration procedures used by BHP Engineering to ensure that the project was Successful.

Jan 1, 1983

Tourmaline-bearing rocks are a rare rock type of Suites 3, 4 and 5 at Broken Hill. Minor laminated plagioclase-quartz-tourmaline rocks occur in association with the quartz- magnetite rocks of Suite 3 with the greatest abundance of tourmaline-bearing rocks present in Suite 4 intimately associated with lode horizon, scheelite mineralisation and zinc mineralistion - all approximate strike equivalents of the Broken Hill Pb-Zn-Ag deposit. Bedded quartz-tourmaline rocks, tourmalinites, tourmaline-rich pelite and tourmaline-bearing lode horizon have been recorded from suite 4. The bedded tourmaline rocks rarely display cross bedding, graded bedding, slump structures and small scale intraformational breccias. Minor tourmaline-gahnite-bearing pelites are present in Suite 5. The sedimentary structures, metamorphic textures, the stratigraphic position of the tourmaline-rocks and the presence of quartz-tourmaline-gahnite-spessartine (-fluorapatite) lode rocks indicates that the mineralisation at Broken Hill and the tourmaline-rich rocks are all products of submarine exhalative hot spring systems which were most active during deposition of Suite 4 rocks. Tourmaline is chemically different from that associated with granitic activity and from other submarine exhalative tourmaline-rich rocks because the premetamorphic alteration at Broken Hill involved addition of Fe, Ti and F and subtraction of Mg - a feature reflected in the chemistry of tourmaline from Broken Hill.

Jan 1, 1983

By Ellson I. G

Shay Gap was created for the sincrular purpose of housing, in comfort, the workforce that would be required to mine iron ore, from leases held by Goldsworthy Mining Limited, in hill country, approximately 170 kilometres east of Port Hedland in the Pilbara region of Western Australia. To combat the and environment, the Company ultimately decided to adopt a novel planning concept for the town, which had not been attempted before in Western Australia. The special problems encountered during planning, and the reservations that were expressed during construction and early settle ment, are now part of the dim past. During the three years of occupation now achieved, there has been accumulated a story of success in the provision of an acceptable alternative to modern suburbia. Not only may this be claimed, but it can also be argued that the Shay Gap concept has been a more successful solution to a real environmental problem in our arid Pilbara region than has been seen in other similar settlements.

Jan 1, 1976

Physical model testing at Bergbauforschung is done in two rigs, a roadway rig and a longwall rig. The loading of such models, in scale relation to the con- ditions in the collieries provides valuable guidance to the probability and nature of failures, and thus to support requirements, in structural, roofbolts and self- auvancing supports. The success of such modelling when related to subsequent underground designs put to use suggests that such methods of investigation could be extended to pillar extraction problems also.

Jan 1, 1974

By Sharpin PC

The countercurrent gas-solid-heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temp-erature distributions through the drier have been calculated. Although the calculations rest on several simplifying assump-tions, to be corrected as the experimental work develops, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating con-ditions on the rate of drying of the briquettes which-controls the 2 strength of the char produced. The analysis shows why a limitation was reached in the improvement of char-strength in the pilot plant in 1961 and a prediction is made of ' a way ' in ' which the limitation could be overcome.

Jan 1, 1963

By Reeves T. J, Hansen J. Y

Dense medium cyclone theory, supported by extensive experimental and plant-scale evidence, demonstrates that medium rheology (stability and viscosity) substantially affects cyclone performance in mineral applications.Two instruments have therefore been developed to allow medium stability and viscosity to be-monitored in the plant environment. The instruments are described, and examples are given of their application in full-scale plants.

Jan 1, 1989

By Warner RE

SINCE 1952, when Elliott et a/ first applied the Sherwood correlation for flooding in chemical absorption towers to blast furnaces numerous investigators throughout the world have followed their example and much research effort has been spent to tighten the correlation and recently to extend investigation of flooding to side gas entry conditions. The widespread use of the Sherwood concept of flooding has been such that even the word itself has become an integral part of blast furnace nomenclature. The evidence for the applicability of Sherwood's relationship has been that the flooding limits calculated from blast furnace parameters lie approximately on the Sherwood line. However, the values of many of the variables for the blast furnace calculation are only estimates and at first sight one may wonder at such 'close' coincidence when some of the estimated parameters entering the Sherwood correlation are raised to the power of three or more, as for the bed porosity and the liquid surface tension. It is felt that the explanation of this result lies in the logarithmic: nature of the plot and/or the fortuitous can- cellation of the errors of the estimates in the calculations coupled with the fact that blast furnace fluid ratios lie within a very narrow range of values. The foregoing considerations should in their own right place doubt on the correctness of the Sherwood type flooding correlation applied to the blast furnace. Additional doubt regarding the existence of the Sherwood type flooding in the furnace has been cast by the results obtained in the Tokyo University experimental blast furnace. From the reasoning of both Standish and Colquhoun (p. 20) and Warner (p. 23) it is deduced that flooding in the traditional sense will only normally occur in the upper bosh (somewhere near the mantle), following softening as discussed by Palella et a/ on p. 75, and flooding in that zone is likely to result in furnace irregularity. On the other hand, the concept developed by Warner of slag hold-up above the raceways as a stable phenomenon not affecting furnace regularity is a process unique to the blast furnace and is not described by the Sherwood flooding theory. Recognising the considerable practical implications of slag hold-up above the raceways, this note further explores the physical process of slag hold-up. We envisage that bed of coke above the raceways in almost all blast furnaces would contain some slag held up by the gas pressure gradient. In general the slag would be contained in a ring and gas would bubble through in its ascent through the furnace. The force supporting this slag is the pressure gradient and obviously -much of the blast pressure is dissipated in supporting this structure.

Jan 1, 1975

By Nidagal V

This paper discusses the dewatering strategy adopted and the considerations and procedures required to incorporate a dewaterinq scheme into the Mt Whaleback mining operation. It concludes that in pit pre-dewaterinq has successfully allowed mining to progress below the standing water level with the minimum of disruption or radical change to the mining method. It is recognised however, that dewatering is not a static activity and there is a requirement for ongoing investigations and development. Pre-dewatering commenced in October, 1984. Purpose designed pumping trailers have been employed to minimise the loss of pump availability resulting from the frequent. need to remove and reinstall pumps when close vicinity blasts occur. To July, 1986, some 0.5 Mm' of groundwater had been pumped from the unconfined orebody aquifer. Mining has progressed to some 20 m below the standing water level without. any undue water associated problems. Ultimately, it is ,cheduled to extend some 300 in below the original water level in the West Pit. With the development of an increasing area of the mine below the standing water level, the influence of seasonal high intensity rainfall events, which had previously caused little concern, now need to be addressed. Pumping equipment has been designed to evacuate storm water at a rate consistent with mine production Considerations.

Jan 1, 1986

Mining of narrow vein mineralisation, invariably depending on the mining method selected, involves the extraction of both ore and waste rock. The level to which mining of waste rock can be minimised depends on numerous factors, but particularly the thickness and dip of the deposit. Resue mining is a method of mining that allows split face firing within stopes to allow waste and ore to be mined separately, allowing dilution to be minimised. This paper examines the technique of resue firing and its applicability to the mining of narrow vein deposits. Particular emphasis is placed on the conditions in which resue mining presents a suitable option for mining of narrow veins.

Jan 1, 2008

It was once considered sufficient to revegetate old mine sites using grass or trees. At the commencement of the Stawell JV (SJV) operation in 1981, management determined that pre-existing vegetation would be replaced. This policy was somewhat 'ahead of its time'. The cost of rehabilitation at SJV averages $8000 per hectare. Rehabilitation of this calibre requires a practical understanding of local ecosystems.

Jan 1, 1992

By Ruston R

When coal mining first commenced in Australia, the principle objective was low cost production with development directed toward recovery of 'easy' coal. Future expans- ion of these early mines into major under- ground operations was neither envisaged nor planned. As the demand for coal grew, these mines were expanded to increase output. however, the absence of initial ventilation planning brought about ad hoc systems wh;ch required continual repair and upgrading. These systems proved satisfactory in the short term because the majority of undergrouni coal mining operations were carried out at relatively shallow depths where gas emission rates were low. By comparison, coal is now being won at depths exceeding 500 metres with a corresponding increase in gas flow from the working seams and adjacent strata. The following paper addresses, firstly, the planning and institution of a ventilation system in a mine where previous inefficiencies were many, and secondly, the value of pre- planning a mine ventilation system in the early stages of mine development, and the need to continually review and upgrade the plan to account for unforeseen ^hanges.

Jan 1, 1983

By Restarick C, Jowett A

A cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone plus in some tests a variable cyclone spigot, has been used to achieve classifier separations at unusually coarse sizes relative to the diameter of the units used. The method has proved to be useful for low tonnage flows at low pulp density and variable feed rate. The system relies on use of a cylinder unit to reject excess water and fine particles, the amount rejected being adjusted by the flow control valve. The valve also adjusts flow rate and pulp density of feed to the cyclone unit, and can be adjusted to give a separation at a coarse particle size. The system has been used in connection with experiments on the pilot plant at Mount Isa, where a 76 mm system was used to classify feed to the lead secondary rougher circuit at sizes as coarse as 52 micrametres galena equivalent for split conditioning tests. Further tests have been carried out with quartz to assess the range of size separations Possible.

Jan 1, 1978