Search Documents

By Mimura K

The carbon reduction of tantalum pentoxide was investigated in a plasma-arc furnace. The sample was a mixture of tantalum pentoxide and graphite, vacuum pressed into a briquette and was reduced at about 3100¦C. Argon was used as the are gas. The optimum mixing ratio of carbon and tantalum pentoxide, C/Ta205 is 5.10--5.15. The sample, weighing 7 g is fused within 60^ 70 seconds by plasma-arc heating and the reduction of molten tantalum oxide with solid carbon pro- ceeds rapidly to approximately 99.5 % Ta during this period. The reduction that follows in the molten state is slow. Within about 10 minutes, the maximum tantalum content of the massive metal product reaches 99.9 % and the oxygen and carbon remaining in the product are 50 ppm and 400. 500 ppm respectively.

Jan 1, 1980

The paper describes the 209 in. single stage axial flow mine ventilating fan which commenced operation at The Zinc Corporation Limited, Broken'Hill, N.S.W., in January, 1954.This fan is used to ,ventilate the underground workings of The Zinc Corporation Limited and New Broken Hill Consolidated Limited and, at the time of installation it was the largest fan of its type in the world. It has amaximum capacity of 900,000 c.f.m. at 4·2 in. watergauge and is equipped with adjustable pitch blades and a novel form of variable speed drive.The considerations which lead to the adoption of this particular design are outlined, and a full description of the contruction and installation of the fan and auxiliaries is given.Comprehensive acceptance tests were carried out on the completed installation and, the testing procedure is described in detail. The results of sound level measurements are also included. A brief report on the performance during the 12 month period from 1st July, 1954, to 30th June, 1955, is then given.SELECTION AND DESIGN OF FANGeneral ConsiderationsBecause of the economic advantages of joint ventilation of the underground workings of The Zinc Corporation Limited and New Broken Hill Consolidated Limited, it was decided, after a full review of the future ventilating requirements of both mines, to sink a 20 ft. diameter circular upcast airway on the common boundary of the two properties, to handle a maximum quantity of 900,000 c.f.m.The anticipated air requirements were at this stage estimated to be:(a) initially 700,000 c.f.m. through a mine equivalent orifice of 160 to 2'40 sq. ft. (equivalent total pressures being 2·70 in. w.g. and 1·20 in. w.g.) ;

Jan 1, 1956

In 1980 Pancontinental Mining Limited decided that while the Jabiluka uranium project was still a major focus of the company's efforts some diversification was necessary. At this time it was decided to include precious metals in Pancon's exploration and acquisition objectives. As a result the now Paddington Gold tenements were acquired, explored and developed. Today, it rates as the 6th largest gold mine in Australia and at an expanded throughput of 1.2 million tonnes per year of ore it will produce about 110,000 ozs of gold per year. Following extensive exploration activities by Pancon's Exploration Division the Operations Division continued with development drilling finally proving up a reserve of about 8.4 million tonnes at an average grade of 3.2 g/t. An in- house preliminary feasibility study was followed by a two phase feasibility study by Davy McKee. This resulted in a recommendation to the Pancon Board of Directors to develop Paddington with an annual throughput capacity of 875,000 tonnes. This paper describes the acquisition, exploration and development of the Paddington project. It goes on to

Jan 1, 1986

By Bunting HR

Developments since 1959 in major excavators to meet the high outputs of overburden and coal under the changing nature of the Morwell Coal Deposits of the Latrobe Valley are described. Particular reference is made to investigations of designs of the bucket wheel head configurations for the digging of flat batters on high faces, and examples are given of the wide use ofmodelsin these studies.An explanation is given of considerations leading to selection of the Long Boom or the Compact type of bucket wheel excavator for various applications. The past decade has seen increasing manufacture in Australia of components for excavators and similar machines. The measures undertaken to integrate these components with those from overseas (Germany) are described. A section of the paper deals with advances in Electrical Engineering for large excavators in Australia and its interdependenee with mechanical design and construction. Finally, as an example of the versatility of the bucket wheel excavator a description is given of a recent application for the mining of mineral sands in Northern N.S.W.

Jan 1, 1970

By Aspinall T. O, Loch R. J, Bell L. C

Design of reshaped spoil surfaces is an important pan of rehabilitation of spoil piles resulting from open-cut coal mining. To achieve the optimum design, it is necessary to make accurate predictions of soil losses from spoil piles. Predictions can be based on data gathered using laboratory and field rainfall simulators and field plots. These data are used to derive input parameters for erosion prediction models. Model input parameters include rainfall erosivity, spoil erodibility, sediment size distribution, runoff, soil loss and peak runoff rate. Model outputs can be used in design and include predicted sediment size distribution and predicted soil loss.The traditional method of gathering input data is monitoring field plots. This method is very expensive, must be done on a long-term basis and is affected by irregular rainfall. Long-term field plots are necessary to obtain data that can be applied to empirical prediction models such as the Universal Soil Loss Equation (USLE).

Jan 1, 1992

By Dinuzzo P, Wychie J, Desoe C

The Selwyn Gold-Copper Mine is located 150 km southeast of Mount Isa within Proterozoic units of the Mount Isa inlier (Figure 1). Mineralization in the mine area is associated with strongly sheared ironstones and iron rich schists at the base of the mid- Proterozoic Staveley Formation. The ironstone horizons outcrop as a series of dominant ridges over a 10 km strike. Economic gold-copper mineralization has been defined in 4 separate zones within a 3.5 km length of the outcropping ridges. A current combined geological resource for the deposits is 5.3 million tonnes of 5.0 g/t Au and 2.02 Cu. Weathering of the deposits has resulted in a pronounced vertical zonation of mineralogy, especially copper, within the ore zones. This has produced 3 separate ore types which require different treatment techniques. The categorization is based on copper content and zones are termed leached (surface), oxide and sulfide. Ore removed from the pits will be mainly leached and oxidized with minor sulfide near the pits final depths, while the underground ore will be from the sulfide zone with minor oxide in some areas.

Jan 1, 1989

By McCarthy P. L

A distinctive feature of the goldfields of Victoria was the extrac- tion of gold from deep leads, that is the buried river beds of Vic- toria's ancient rivers and streams. It is estimated that about 265,000 kg of gold was produced from Victoria's deep lead mines which comprises about 11.5% of Victoria's total production of gold (Bowen, 1974). The significance of deep lead mining for Victoria, however, went far beyond its economic contribution to Victoria. If Profes- sor Blainey is correct it was the frustrations of mining gold from deep alluvial leads in Ballarat during 1854 which precipitated the Eureka Stockade (Blainey, 1963, 46-52). This event resulted in the implementation of a fair mining administration and was an emphatic statement of the rise of democratic movements in Australia. Much of the technology and skill for mining deep leads had to be developed locally because at that time no other major gold- field elsewhere in Australia or the world had gold deposits with comparable problems. Deep lead mining in Victoria was there- fore largely a home grown industry and the equipment for that industry was often designed and produced in Victoria.

Jan 1, 1988

By Draper J. J, Jell J. S

The Burdekin Basin in the Townsville hinterland is an intracratonic extensional basin which contains up to 4500 m of marine and continental siliciclastics and carbonates. The basin sequence is recognised as having accumulated during five major episodes of deposition. Facies analyses of these show that each consists of one or more transgressive or regressive phases. Each episode led to the accumulation of thick sequences in several half-grabens in a transtensional back-arc setting. The depositional episodes can be recognised in comparable sequences in the Broken River Province to the west and Drummond Basin to the south.An Early Devonian episode resulted in the deposi-tion of dominantly marine facies, currently mapped as Fanning River Group, in the northern part of the Burdekin Basin. Two transgressive phases are recorded there, firstly in the Pragian, then later in the late Emsian to early Eifelian. A Middle Devonian episode is represented by dominantly marine facies of the Fanning River Group, representing the peak of a widespread late Eifelian to Givetian transgressive phase. A Late Devonian episode is characterised by continental facies of the Dotswood Group. Deposition occurred during a major regressive phase in response to regional uplift of surrounding areas, and the onset of acid-intermediate volcanism to the south. A Late Devonian to Early Carboniferous episode followed, which was a period of alternating marine transgressions and non-marine regressions that resulted in the deposition of the Keelbottom Group. A final Early Carboniferous episode, marked by the deposition of calc-alkaline volcanics and non-marine faciesòof the Glenrock Group, was a direct outcome of Early Carboniferous subduction further to the east. Compression of the basin followed in the Late Carboniferous, resulting in folding and reactivation of basement faults.

Jan 1, 1990

Traditional vat leaching has been done on a batch basis, which involves loading the vats, leaching, drainage, washing, draining again, and unloading. As a result of these many steps and the attendent cost of labor, vat leaching is generally not an economic proposition. Also, like heap leaching, there is a tendency for channeling to occur within the bed, whether the leach solution flow is by percolation upwards or downwards. No doubt experimenters over the decades have been enticed by the idea of fluidization induced by upward flow through the ore bed. If the bed could be fluidized, then a continuous flow of material could be set up, dispensing with the high cost of loading and unloading the vat. A quick calculation of solution flow requirements, however, soon reveals that the volume of constant liquid movement necessary to sustain fluidization is prohibitive from a power and cost standpoint. The premise of the Mackie Vat Leaching Jig (MVLT) concept was that the large volume of liquid flow required for fluidization could be achieved instantaneously, and that during this small element of time, the solids would flow under the influence of the hydraulic gradient in the vat. If this procedure could be repeated in a cyclic manner, then a steady-state condition could be set up. Experiments in the laboratory demonstrated that solids flow could be achieved in this manner.

Jan 1, 1991

Attention is drawn to the largest eruptions with dense rock equivalent (D.R.E.) volumes approx-imating 50 km3. These have been strongly clustered during the last 40 000 years, with 11 recognised in the period 35 000 to 22 000 years ago, and 10 in about the last 9000 years, but none in the period 22 000 to 9000 years ago. With the latest such eruption, at Tambora, only 175 years ago, it is likely that we remain in a period of increased activity. During the last 100 000 years, roughly the period during which modern Homo sapiens has existed as a species, there has only been one eruption an order of magnitude larger (>_ 500 km3 D.R.E.). This took place at Lake Toba, Sumatra, about 75 000 years ago, and is estimated to have deposited ash to a thickness of a centimetre or so in parts of Ethiopia, Somaliland, Saudi Arabia and Iran, and to a thickness of a few millimetres in the eastern Mediterranean. The average interval between global eruptions of this magnitude is probably about 40 000 to 50 000 years. Insufficient work on the Quaternary history of volcanoes has been carried out to suggest where the next such eruption might occur. At Yellowstone, which has been well studied, the average interval between very large explosive eruptions is about 700 000 ¦ 120 000 years.As a prerequisite for magnitude-frequency analysis of eruptions, and hazard and risk impact assessments, it is important to classify past eruptions in a consistent manner. In an attempt to find a universally applicable method to estimate order of magnitude D.R.E. volumes from the distribution of airfall tephra, an empirical correction has been derived for the elongation of tephra dispersal fans due to wind. Dispersion distances for various thicknesses of tephra, recalculated for windless conditions, have been obtained from a study of about 40 tephra isopach maps for which D.R.E. volumes have been calculated, and a range of distances derived, equivalent to D.R.E. volumes from 106 m3

Jan 1, 1990

The population and the per capila consumption of mineral resources have both grown dramatically during the century past. It is argued that growth will continue through the century ahead but that the magnitudes of undiscovered resources are probably adequate to meet demands. The challenge that the mineral explorer of the future will face is finding deposits beneath several kilometres of barren rock.It is further argued that the principal challenge that society will face in the century ahead is the amelioration of environmental stress.

Jan 1, 1993

By Rabie A. S, Fouad K. M, Ammar A. A

The existence of Gabal El Kahfa ring complex, located in the Eastern Desert of Egypt, has been ascertained from aeromagnetic and aeroradiometric survey data as well as by aerial photography. Two maps for -the net aerial radiometric measurements reduced to ground level and aerial magnetic data corrected for the regional normal gradient of the earth's magnetic field have been constructed. The aeroradioactivity data have been interpreted geologically and analyzed statistically to outline various radiometric units and compute their charac- teristic statistics. The ring complex showed a circular radiometric feature and yielded a radiometric mean background and a standard deviation of 6.48 and 0.89 pR/h respectively. Besides, the observations showed a normal distribution. The aeromagnetic data have been reduced to the north magnetic pole, then filtered to produce the regional-and residual-component maps. Statistical trend analysis was conducted for the tectonic linea- ments resulting from the three magnetic maps, to define the structural framework of the area under study. This statistical study proved the exis- tence of trends in the east-west, northwest-south- east, northeast-southwest and north-south directions. The ring complex is characterized by a circular magnetic feature, whose average relief is 2150 nT. It is included within a high east-west trending magnetic zone. The latter represents a deep-seated uplift or anticline which is bordered from all sides by some faults of different trends.

Jan 1, 1988

By Ariti J

The mineralogy and extractive metallurgy of platinum and palladium in ores and residues is examined and the relative reactivity of Pt, Pd, PtS and PdS in cyanide and chloride media at 20¦C is discussed. Electrochemical measurements establish that Pd is readily leached in chloride media but more slowly in cyanide media due to a passivating PdO film. The passivating oxide film on Pt prevents leaching in either system at ambient temperatures. The results of leaching Au, Pd and Pt from an iron oxide residue obtained from the Sherritt Gordon Process using CN/air and Cl-/H202 are compared. It appears that passivation is overcome either by roasting at ?600¦ or by leaching at >_100¦C.

Jan 1, 1991

By James CH

For drainage sediment to be used as a successful sampling medium in reconnaissance geochemical surveys, the length of any dispersion train from a typical target must be great enough for it to be detected by a widely spaced sampling pattern, and must also be homogeneous enough to avoid it being missed by the unfortunate selection of a random low value sample. Elements which occur in stream sediments in the form of discrete heavy minerals present two special problems in this regard. Since the element is concentrated into a few particles, the medium is extremely heterogeneous, which makes representative sampling impossible unless very large samples are taken, while the high specific gravity of such grains leads to their being concentrated in traps along the stream bed. Several ways of overcoming these difficulties have been suggested. Among these the "schlich" test, in which heavy material obtained by panning is taken for analysis is among the most popular. However, the results of the present study indicate that while this method improves the nature of the patterns obtained, they are still far from satisfactory. Alternative methods of sample preparation, including the taking of light material for analysis, appear to provide better answers to the problem. In the area studied this approach eliminated most of the "noise" associated with the data obtained by other methods, as well as giving an extended dispersion pattern.

Jan 1, 1986

The ore deposits of the Oobar mining field are confined to sediments of the Early Devonian Cobar Supergroup. The mineralisation is discordant to bedding and parallel to cleavage. The structural association is variable with the deposits near the eastern margin of the Cobar Basin formed in zones of deformation and faulting. The Elura deposit located further to the west is in less deformed sediments within the core of a small anticline. There are wide variations in ore type fran lad sulphide chalcopyrite - pyrrhotite - pyrite to high sulphide sphalerite - galena - pyrrhotite - pyrite assemblages. The deposits ccnmonly contain an inner zone of quartz - sulphide - chlorite veining grading outwards into a chlorite halo containing quartz - carbonate veining. The Elura deposit differs in having an inner massive sulphide zone surrounded by a zone of big-Fe carbonate formation. The mineralisation probably formed during regional metamorphism and deformation in the Early Carboniferous. A possible genetic model involves the injection of metal bearing hydrothermal fluids formed in the upper mantle or lower crust up basement structures into the overlying Cobar Supergroup sediments. An alternate model proposes the leaching of metals from the sediments by brines formed during metamorphism and subsequent emplacement in favourable structural zones.

Jan 1, 1983

The Douglas mineral sands deposit is located 75 km north of Hamilton in western Victoria, Australia. The deposit was discovered in the late 1990s by Basin Minerals Limited and purchased by Iluka Resources Ltd in 2002. Prestrip mining commenced in December 2004, with ore mining commencing in August 2005. Douglas is the first of several projects being implemented by Iluka Resources Ltd in the Murray Basin, with all heavy mineral concentrate planned to be treated at the companyÆs mineral separation plant in Hamilton. The mineralisation at Douglas lies along the south-eastern margin of the Murray Basin. It is hosted by marine Pliocene Loxton-Parilla Sands and consists of three discrete deposits; Bondi Main, Bondi West and Bondi East. The mineralised sediments dip at a low angle to the west and lie unconformably beneath a veneer of top soil (50 - 100 mm) and subsoil (up to 600 mm) and between three to 12 m of overburden. The barren overburden, characterised by high clay content (<53 ¦m material) generally provides a stark contrast to the sandy ore, which is between 1 m (parts of Bondi East) and 15 m (Bondi Main) thick. Both overburden and ore are removed utilising standard dry mining techniques using both scraper-bulldozer and truck-excavator combinations. All ore is delivered to run-of-mine (ROM) stockpiles before being reclaimed by front end loader into the processing plant. Grade control at Douglas is based around visual dig control aided by high precision survey, which enables accurate reference to the resource drilling and block model data. Vertical excavator faces, inclined scraper faces plus regular test pits and trenches provide opportunities for in pit mapping and sampling. This data is used to refine not only the resource estimate for Douglas but also the drilling, interpretation and resource modelling methods used for similar deposits across the basin. The foundations of the geological reconciliation process at Douglas are the in pit surveys undertaken each time the mining fleet has completed building a ROM stockpile. These surveys and the subsequent interrogation of resource models enable robust estimations of the heavy mineral content of the stockpiles, which are subsequently used to predict the daily input grades into the plant during their reclamation. Reconciliation of this daily data is then undertaken at the end of each month against metallurgical production data and plant balances. Learnings and results from the reconciliation process are used to further refine subsequent resource models and modelling methods.

Jan 1, 2009

By A Galley, M Plouffe, T Hynes

Canadian mining research has recently been reinvigorated through a pan-Canadian research strategy driven by the industry, the research community and government departments. These organisations have come together to form the Canada Mining Innovation Council, whose role is to focus and increase mining research in the country. One of the major themes of the organisation is environment; including major research initiatives on energy, tailings and environmental stewardship. Other major initiatives on exploration, mineral extraction and mineral processing will also consider environmental benefits in the research projects they undertake. All the initiatives have their priorities determined principally by the mining and exploration companies, whose first obligation is to determine the long-term research priorities of the industry as a whole, rather than for their individual companies. Only after industry consensus on priorities does the research community become engaged in the implementation of specific projects to address those identified priorities. A goal of the program is to effectively create a virtual mining research laboratory, by engaging all the major research centres in the country. Membership to date includes most of the major mining companies operating in Canada and almost all of the mining-related universities. Other members include federal, provincial and territorial governments, consulting and service companies and manufacturers.CITATION:Hynes, T, Plouffe, M and Galley, A, 2012. A new approach to mining research in Canada, in Proceedings Life-of-Mine 2012 , pp 333-338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Thuli AJ

Copper concentrate from Bougainville's copper mine located on the west slope of the Crown Prince Range on Bougainville island, is pumped 27 km to the filter and drying plant at Anewa Bay for preparation and storage prior to shipment to overseas customers. Prior to shipment the thickened concentrate slurry is passed through a test loop to check that its consistency and pH are acceptable for transportation through the main pipe line. The Bougainville pipe line is unique since it is the world's first copper concentrate system. where slurry is pumped an appreciable distance against a high head,

Jan 1, 1975

By Higuchi K

In this paper, the history of Japanese coal and gas outbursts is presented and circumstances and countermeasures at the time cf outbursts are summarized statistically. Then the present meth- ods for prevention used practically in Japan are introduced. From statistics, it was reconfirmed that Japanese coal and gas outbursts have occur- ed frequently in the district of geological disturbance, symptoms immediately before out- burst occurrence were the phenomena in connec- tion with failure of a coal seam and outbursts have occurred many times when the number of boreholes had not been sufficient to degas. One of the principal protective method adopted in Japan is the large diameter gas drainage boring which also posesses a stress relief effects. There is a tendency to make diameter of borehole larger to increase both stress relief and degassing effects.

Jan 1, 1986

By Mankosa MJ, Yoon R-H

A reliable scale-up procedure for column flotation must address three important areas of column design, ie column geometry, sparging system and wash water distribution network. The column geometry is dictated by the maximum froth carrying capacity (which determines column diameter) and the bubble-particle attachment rate and particle retention time (which determines column length). The most important factor in the scale-up of an air sparging system is the ability to produce small bubbles in both laboratory and full-scale columns. Other factors, such as energy consumption and maintenance requirements, should also be considered in the scale-up of bubble generators. It is also important to design a wash water distribution system that can properly control the froth stability and maximise the column throughput. Based on these criteria, a successful scale-up example is given.

Jan 1, 1993