Search Documents

By D L. Decker, G C. Miller, C Papelis

Arsenic, often associated with precious metals ore deposits, is a major contaminant released during large-scale gold mining. Because of the complex oxidation/reduction and sorption behaviour of As, prediction of the long-term mobility of As in pit lakes is uncertain. The behaviour of As in pit lakes is investigated in this paper by conducting a series of laboratory experiments where As is allowed to adsorb onto pit lakes sediments. Experiments were conducted over a range of pH with both As(III) and As(V) allowed to adsorb onto sediments collected from existing pit lakes found in the three main orebody types in Nevada, USA; porphyry copper, quartz-adularia gold, and Carlin Trend type gold deposits. Results from adsorption experiments show that As(V) and As(III) adsorption is strongly pH dependent with higher uptake at pH 5 and lower uptake at pH 9 for As(V) and higher uptake at pH 9 and lower uptake at pH 5 for As(III). This behaviour, as expected for oxyanions, has been described previously for agricultural soils, iron oxides, and Carlin Trend heap materials. Maximum adsorption of As(V) for the Carlin Trend type gold sediment was 3.0 g/kg at pH 5, 2.0 g/kg for the quartz-adularia sediment, and 0.9 g/kg for the copper porphyry sediment. Maximum adsorption of As(III) for Carlin Trend type gold sediment was 2.5 g/kg at pH 9, 2.2 g/kg for the quartz-adularia sediment, and 2.1 for the copper porphyry sediment. Adsorption isotherms are non-linear and show Freundlich isotherm behaviour. Variations in sorption between the different pit lake sediments under similar conditions can be explained by differences in the elemental composition of the sediment. Most rock forming elements from XRF analysis are similar in quantity except for Fe. The Fe content is highest in the Carlin Trend type gold deposit sediments and lowest in porphyry copper deposit sediments and is the third most abundant element in all three sediments. The Fe content of the sediments correlates well with the amount of As sorption seen in the laboratory experiments.

Jan 1, 2003

By Bruce P, Luyendyk

The South Island of New Zealand comprises a collage of distinct tectonostratigraphic terranes. Some tectonic models predict that these terranes formed on or near the margin of Gondwanaland. However, geologic evidence suggests that some of these terranes may be exotic. Over 400 samples from 30 sites were collected from the Brookstreet terrane within the Takitimu Mountains. The section includes the early Permian Takitimu Group and the late Permian White Hill Intrusive Suite. Over 80% of the rocks show a partial or complete regnetization in the present field due to recent acquistion of VRM. Although some remagnetization of the Takitimu Group occurred during the emplacement of the White Hill Intrusives, both early and late Permian direction have been isolated. These directions indicate a mid-latitude origin for the Brookstreet terrane, and suggest a strong clockwise rotation between early and late Permian time. A published paleomagnetic result from the younger, but related, Murihiku terrane suggests that the Brookstreet terrane was sutured to the margin of Gondwanaland by the late Triassic, or that the Brookstreet and Murihiku are two distinct terranes.

Jan 1, 1987

By G R. F Alvear Flores

Mineral resources are becoming more complex in composition and structure making it more difficult to produce clean concentrates for primary metal smelting. In parallel, providing technological solutions to the recycling and recovery of end-of-life materials is becoming more important in moving towards the goal of increasing circularity. The availability of fundamental thermodynamic data and advanced thermodynamic tools greatly assists in evaluating these complexities and their impact on existing and new processes. In addition, it is fundamental to support the economic performance of smelters. This paper describes several examples on how fundamental work can be applied to industrial processing..

Jun 17, 2024

By Kato Y

As a direct result of the Mining Industries need to improve efficiency and production in Open Pit type operations, the size of haulage units have increased dramatically. This trend has continued such, that the majority of dump trucks operating in Open Pit operations are in the 170 ton class. Continued mining in existing locations has meant that the increase in vertical lift and resultant grades, and increases in hauling distances are making electric drive systems unsuitable. This is largely due to the electric drive systems heat limitations on major propulsion components. With these mining requirements in view and the present limitations on electric drive systems in mind, Komatsu have been developing the Komatsu HD1600M. A diesel powered mechanical drive dump truck capable of operating in deep pit operations. This presentation introduces: Komatsu HD1600M Dump Truck

Jan 1, 1982

By R H. Knight

Uncertainty in prediction and modelling of geological (physical) ore continuity in geometrically complex ore deposits is a key risk factor in mining. Reducing geometric uncertainty of hard-boundary ore/waste contacts and related geological features improves the efficiency of local mineral resource estimation and reserve calculation, mine/stope planning, ore control and in-mine exploration. Detailed underground mapping of serial-level drives provides a continuous record of the characteristics and contact configuration of ore, as well as crucial ore-related geological features that are required to resolve geometrical variability when closely spaced drilling proves inadequate or is cost-prohibitive. The mapping-based approach described in this paper re-establishes the focus on the geology of the orebody by incorporating high-value, detailed geologic mine mapping information. Mapped ore-related configurations and relationships, recorded on a succession of faces or on a series of levels, provide the basis for 3D interpolation and extrapolation of the local geologic continuity of an orebody. Correlative points representing locations of key ore-related geologic features on each face or level are linked by 3D polylines or trajectories forming a coherent geometrical framework. The coherent progression of geometric changes mapped by these trajectories reveals the overall ‘dynamic’ of the geometrical framework, as well as the spatial tendencies of its geological constituents. Distinct sets of ore control trajectories are selected from within the framework and are used in the construction of alternative geological ore continuity models. As mining proceeds, alternative models are evaluated, and are then either refined or rejected. The geometrical framework is used to evaluate theoretical models and practical heuristics, focus exploration targeting and inform and guide all aspects of mine geology in active mines. This approach also lends itself to analysis of global ore continuity in the re-evaluation of mature or abandoned mines. Its use is particularly effective in geometrically complex orebodies such as the West Branch orebody and the orebodies of No 2 mine of the Balmat-Edwards-Pierrepont zinc district, which are used to illustrate the method. CITATION:Knight, R H, 2014. A mapping-based approach to geological continuity prediction using examples from the Balmat-Edwards-Pierrepont Zinc District, St Lawrence County, New York, USA, in Proceedings Ninth International Mining Geology Conference 2014 , pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

The concentrating plant of the Broken Hill South Limited was described in Proceedings No. 44, Australasian Institute Mining and Metallurgy, December, 1921, by Wainwright and Read. It was erected on the present site in 1907 and 1908.From that date, the plant has undergone various alterations consistent with metallurgical improvements. By 1925, the timber work of the gravity secti"on had seriously deteriorated, so much so, that, when the machinery was working, the floors and supports vibrated badly, causing heavy maintenance costs.In 1928, it was decided to erect a new gravity-treatment section, to be followed later by a new flotation section.

Jan 1, 1932

The history of gold dredging in New Zealand, leading to the develop- ment of the `New Zealand Type' dredge is considered. Much of this infor- mation has come from contemporaneous publications by the New Zealand Department of Mines. Alluvial gold production declined after 1902, and ceased completely in 1982, but is now rising again. The progress of the New Zealand alluvial gold mining industry is considered, together with some of its more exceptional successes. Recent developments are com- pared to those of the past.

Jan 1, 1988

Silica and limestone fluxing levels in copper smelting slags were studied. Copper concentrates with flux additions were smelted to matte (55.5 per cent Cu) and slag in a pilot scale submerged combustion furnace.Results indicated that oxidic and sulphidic copper levels in slags were minimised with a slag Si02 level of 36 per cent and a SiO2/CaO ratio of 5.5. Total copper losses in slags were 0.6 per cent under these conditions.To produce the desired slag chemistry, additions of bulk silica and limestone to copper concentrates of fluctuating grades were predicted numerically. The method employed the solution of two simultaneous equations, each respectively for silica and limestone calculations.The predicted flux additions were applied in a further series of tests and the resultant stages were found to be satisfactory. The method is applicable to smelting 'operations which employ two flux bins, with weigh feeders, so that slag chemistry may be controlled with the flux/concentrate feed mix.

Jan 1, 1985

The emerging discipline of ægeometallurgyÆ is not new but is becoming increasingly recognised as a discrete and high-value activity that reflects an ongoing commercial and cultural trend towards more effective mine site integration and optimisation. Geometallurgy involves a quantified and spatially constrained approach to ore characterisation in terms of relationships to critical processing performance. Industry recognition of the need for large-scale, integrated geometallurgical research is currently supporting a major new research initiative. The AMIRA International P843 æGeMIIIÆ project (geometallurgical mapping and mine modelling) is a cross discipline collaboration involving four major Australian research groups; CODES the ARC Centre of Excellence in Ore Deposits at the University of Tasmania, a world leader in economic geology-related research; the Julius Kruttschnitt Mineral Research Centre (JKMRC) at the University of Queensland, a world leader in mining and mineral processing research; the WH Bryan Mining Geology Research Centre (BRC) at the University of Queensland, which aims to be a world leader in mining geostatistics, operations research and optimisation in mine design and planning; and CSIRO Exploration and Mining in the area of automated core logging. The project is currently supported by 19 global mineral companies. The project aims to deliver fundamental knowledge, tools and methods for more effective approaches to geometallurgical definition of mineralogy, element deportment and texture that can be linked to mineral processing performance and efficiency at a range of scales. Outcomes are improved predictive indices of processing performance that can be embedded in resource block models to define processing domains, which can be exploited in mine planning and optimisation. To achieve these aims the project is involved in a range of technology developments that include more automated core logging technologies, new applications of automated microscopy and development of software-based texture analysis and categorisation techniques. Attributes derived from these measurement technologies are used to develop predictive processing models linked to new small-scale physical testing regimes.

Jan 1, 2009

By P Cleary, G K. Robinson, J Hilton, P Wilson

Concern has been expressed that Vezins can be biased when used for sampling fine materials if the cutter speed is as high as the 0.6 m/s which is often used. Using modelling techniques that consider airflow as well as particles, we have endeavoured to investigate sampling bias as a function of the size of fine particles, cutter aperture, cutter speed, shape of cutter blades, and the size of the gap between the inlet pipe and the cutter blades. Using crude estimates of the rate of airflow and a simple model of a single particle moving through air led to an approximate rule that bias will not occur due to mechanisms related to airflow for particles larger than about 200 microns; and bias will always occur for particles smaller than about 40 microns. For particles between these size limits, the extent of bias depends on particle density, cutter speed and cutter geometry as well as particle size.CITATION:Robinson, G K, Wilson, P, Hilton, J and Cleary, P, 2012. Avoiding bias when using vezins for sampling dusty materials, in Proceedings Sampling 2012 , pp 109-114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By C Taylor, E Retz

Sequential Gaussian conditional simulation of wide-spaced exploration data has been completed in order to optimise a drilling grid at Fortescue’s Eliwana deposit. The aim of this drill grid is to improve the confidence in the Inferred Mineral Resource. A mineralised domain within the Joffre Member of the Brockman Iron Formation was selected to be tested as it makes up a large proportion of the Inferred Mineral Resource and is drilled at a reasonable spacing.One hundred realisations of Fe, SiO2 and Al2O3 grades were completed in the domain. Three realisations were selected for each analyte to represent the range of equiprobable values and a further realisation was selected to represent the truth data set. These realisations were used to flag theoretical drill holes on varying spacings and patterns. The theoretical drill holes were used to estimate into block models using ordinary kriging.These estimates were analysed and the accuracy and precision of each drill spacing was assessed. It was concluded that the greatest improvement in estimation results was noted at either a 100 m × 50 m or 50 m × 50 m spacing.CITATION:Taylor, C and Retz, E, 2015. How much do we need to drill?, in Proceedings Iron Ore 2015, pp 491–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Mining is a necessary part of our modern lifestyle. However, mining can cause damage and pollution of the environment and therefore we must manage our resources wisely accounting for the physical, biological and social environments. Contrary to the view of some people not conversant with the facts mining has in many cases improved the environment. This paper described how two sand dune systems that were unstable prior to mining have been stabilised by revegetation after mining.

Jan 1, 1987

By E Hogan, M Goodz, R Wright

The planning, permitting and monitoring procedures of the re-opening and rehabilitation of mine sites is an ongoing process which must continue throughout and beyond the life of the project. Both industry and government bodies must remain flexible to allow guidelines to be altered where and when necessary.To enable the successful re-opening of the Morning Star mine at Woods Point in alpine Victoria, many environmental and historical issues had to be evaluated.The site which had been derelict for 28 years had to be rehabilitated to a safe and aesthetically pleasing state prior to construction of a new operating mine site. Considerable liaison with government authorities and the local community was required.

Jan 1, 1992

The effectiveness of three different types of longwall chock under the three different types of geological conditions worked recently is outlined. Some provisional analyses of the variation of chock load under the shale roof con- dition are briefly discussed and some problems and solutions of gateway and road- head support outlined.

Jan 1, 1974

By J Leppinen, B Johanson, R Kalapudas, G McMahon

The Suurikuusikko gold deposit was discovered in 1987 in western Finnish Lapland, 54 km NNE from the town centre of KittilS in the volcanic belt of Central Lapland. It is hosted by tholeiitic basalts in a graphite-bearing albitite breccia. The ore is located in subvertical shear zones characterised by strong albitisation, carbonatisation and sulfidisation. The ore minerals consist of arsenopyrite, pyrite, chalcopyrite, sphalerite, tetrahedrite, bournonite and rutile. Small amounts of pyrrhotite, gersdorffite, jamesonite, bornite, gudmundite, tetrahedrite, stibnite, kermesite, berthierite and native Sb are also present. Gold occurs as invisible and as 1 - 2 ¦m size inclusions in arsenopyrite and pyrite, on their grain boundaries and in fractures. The average amount of gold leached by cyanide is 2.93 per cent. The æinvisibleÆ gold contents were studied in pyrite and arsenopyrite by electron microprobe analysis (EPMA) and secondary ion mass spectrometry (SIMS) at CANMET/ MTL. Gold element distribution images show zoned patterns both in pyrite and arsenopyrite. SIMS analyses range from 343 to 55 ppm Au in arsenopyrite and from 217 ppm down to 0.32 ppm (detection limit 478 ppb) Au in pyrite. EPMA results range from 939 to below the detection limit 24 ppm Au in arsenopyrite and from 267 ppm to below 22 ppm Au in pyrite. Recovery of the refractory gold ore was studied using grinding, flotation, bio-oxidation and cyanidation tests. A sulfide bulk concentrate containing 40 ppm Au was obtained by flotation at 90 per cent recovery (As content 5.5 per cent, S content 22 per cent, and mass recovery 15 per cent). The grinding fineness in flotation was P80 -100 to 120 ¦m. At the original fineness the cyanidation recovery from the concentrate was lower than ten per cent, after ultra-fine grinding P80 -10 to 2 ¦m the Au recovery was less than 17 per cent. After bio- oxidation, Au recovery of 95 per cent was obtained in carbon-in-leach (CIL). The bio-oxidation time was two weeks in laboratory test, but after regrinding the oxidation rate was faster and recovery of Au higher. However, the selected method for the mining to be started in summer 2008 is open pit mining and mineral processing methods sulfide flotation and pressure oxidation in an autoclave. The ore reserves were estimated 31 December 2007 as: Probable 18.2 Mt with 5.1 g/t Au, Indicated 5.4 Mt with 3.0 g/t Au and Inferred 10.8 Mt with 3.4 g/t Au. The production capacity will be 3000 t/day.

Jan 1, 2008

Both the miner and the Regional Water Board have legal obligations to ensure that all discharges of water from a mine site are free of harmful wastes, and that proper authorisation is obtained to abstract, divert, or discharge water. This requires long-term planning of water management for the whole of the mine site. Guidance is given in the paper on the issues which must be covered in water right applications.

Jan 1, 1986

By de Lassar de Pressigny Y

IRSID has in its laboratories two experi mental counter-current reduction furnaces allo- wing the simulation of the physico-chemical conditions of reduction in any gas-solid coun- ter-current process, including the blast furnace and direct-reduction shaft-furnaces. The counter current is realized by an electric furnace mo- ving along a laboratory tube filled with the material to be tested. The reducing gas stream in the tube travels in the same direction as the furnace After reduction, twenty samples, with dif- ferent degrees of reduction and which can be related to different levels of an industrial furnace, are taken from the tube and subjected to various quality tests. Experiments were realized to determine the behaviour of various types of industrial pellets when reduced under either blast furnace or shaft furnace conditions. The results show the large influence of the reducing conditions on any pa- rameter characteristic of the quality of the pellets : reduction efficiency, swelling, cru- shing strength and disintegration.

Jan 1, 1974

By R McCarthy, P Hawke

FerrAus Ltd's Robertson Range and Davidson Creek Projects are located in the Hamersley Province about 100 km east of Newman, Western Australia. Significant iron mineralisation defined by an aggressive exploration program within the Marra Mamba Iron Formation is shallowly north dipping at Davidson Creek, and mainly shallowly east dipping at Robertson Range, forming part of a regional scale anticline with the granitic and greenstone basement of the Sylvania Inlier as its core. With minor exceptions, the stratigraphy is comparable with that seen in the main Hamersley Basin. Granite and greenstone basement rocks of the Sylvania Inlier are unconformably overlain by shales and volcanic rocks of the Fortescue Group. The overlying Hamersley Group is locally represented by interbedded chert, banded iron-formation (BIF) and shales of the Marra Mamba Iron Formation (Nammuldi, MacLeod and Mount Newman Members), and dolomites, cherts, BIF and shales of the Wittenoom Formation. Iron enrichment occurs predominantly in the Mount Newman Member, and to a lesser extent in the West Angela Member of the Wittenoom Formation. Enrichment varies from 20 - 30 m in thickness in elongate bodies up to 3 km in strike length, and generally thins down dip. At Davidson Creek iron mineralisation is a haematite-goethite-ochreous goethite assemblage, while at Robertson Range this assemblage is consistently overprinted by a later, goethitic alteration related to 'hardcap' weathering. Near surface hardcap alteration in both project areas comprises more siliceous, aluminous and vitreous goethite. Initial exploration completed by Rio Tinto Exploration between 1999 and 2001 indicated the potential for about 20 Mt of iron mineralisation at Robertson Range. Since 2005 a detailed exploration program undertaken by Australian Manganese Pty Ltd (a wholly owned subsidiary of FerrAus Ltd) has defined a global indicated and inferred resource totaling 164.4 Mt at 58.6 per cent Fe (ASX: FRS 17 April 2009).

Jan 1, 2009

The Golden Cross is the first large precious metals mine to be both commissioned and closed in the æmodernÆ era in New Zealand. This paper discusses the life cycle of the Golden Cross mine, with emphasis on the closure process and post closure management.   The closure process has generally been very well managed, and successful, but in spite of that some on-going issues remain unresolved. Nearly nine years after the end of mining the mine owners are still actively managing the site, with no immediate end to that in sight.   The site has been described as atypical, due to the identification of a deep seated landslide below the tailings and waste rock storage facilities. However that should not be given too much emphasis when addressing the overall closure and post-closure management issues, which could well apply to other existing and future mine sites in New Zealand.   The Golden Cross can provide valuable lessons for other miners, and the issues arising at this site should be watched closely by the industry as a whole.

Jan 1, 2006

By J Chßvez, J Rosa del Castillo, J Rui

Environmental Impact Assessment (EIA) and Feasibility Studies (FS) were carried out to evaluate the potential use of treated acid mine drainage (AMD) occurring at the Kingsmill Tunnel in the Central Andes of Peru. The 11 km long tunnel drains the underground works of the Morococha Mining District and discharges about 1.25 m3/sec of AMD directly into the Yauli River in the Amazon Basin. The communities living downstream cannot use the Yauli River water due to its low pH and elevated concentrations of metals (eg Cu, Zn, Fe, Mn, As, Cd) and sulfate. Studies carried out for this project included technical feasibility, EIA, economic viability and social impact assessment phases. During the æTechnical FeasibilityÆ phase, the treated AMD was produced by simulating a high density sludge (HDS) lime neutralisation/ precipitation process and was evaluated for various potential uses. Mining companies located in Morococha, in particular Centromin Peru SA, and the Water Works Company of the City of Lima (Sedapal) collaborated with Golder Associates during the studies. The Canadian International Development Agency (CIDA) provided the financial assistance. The results of the physical, chemical, biological and toxicological analyses demonstrated that the AMD could be sufficiently treated to be potentially used to supplement the drinking water supply of Lima, and for agricultural (eg irrigation and livestock) and recreational purposes. Process design and scale-up parameters were also determined for implementation of the full-scale treatment facility at the site. The use of the treated AMD as a drinking water supplement would be economically feasible.

Jan 1, 2003