Search Documents

By J. L. Bray

LEAD has often been suggested as a protective coating for iron and steel. Such a protective coating should possess: (1) good adhesion, (2) durability, (3) ease of application, (4) freedom from pinholes, (5) good appearance and (6) low cost, but, unfortunately, lead coatings so far produced do not have all of these characteristics. Because of the necessity of carrying out the coating process cheaply, and because lead solutions have poor plating characteristics, most of the efforts have been directed toward the hot-dipping process rather than electroplating. The hot-clipping processes using lead have not been successful chiefly because of the lack of adherence between iron and lead. In any coating process involving iron a bond can be obtained only by the formation of an intermetallic compound, the formation of a solid solution, or mechanical means. Lead forms with iron two immiscible liquid solu-tions, and in the solid state no intermetallic compounds or solutions. It is necessary, therefore, to employ some other element or elements as a binding agent. Tin may be used as in terneplate, or copper in the form of a thin film of electrolytically deposited metal to which the lead will adhere. Because of its physical and chemical properties, lead as a coating medium would undoubtedly be limited in its use to sheet and wire and then only when the article is not subject to abrasion or wear. A very large tonnage of these products are being used under such conditions and a successful lead-coating process should be a valuable contribution to the science. Two other difficulties stand in the way of successful lead coating-that of poor appearance of the weathered surface and the tendency of the lead to form pinholes during solidification. Since lead is commonly accepted as cathodic to iron, these exposed areas are ones of accelerated corrosion.

Jan 1, 1937

By Henry D. Hibbard

FoR the purpose of this paper all steels will be divided into two divisions: effervescing and non-effervescing. This classification must be borne in mind as many statements true of one class are not true of the other. Effervescing steels are those that effervesce in the molds, evolving large volumes of gases, which, in escaping, throw up a spray of molten particles of steel and give the molten metal in the mold a rapid stirring or churning motion until it freezes, or, at least, becomes pasty. This effervescing is intended and proper. The non-effervescing steels, which are more or less completely killed, should not evolve any gas in the molds. Many years ago the writer proposed to call the two classes of steels evolution and solution steels, depending on whether the gases in the molds are evolved or kept in solution, but the present designations seem to be better. In America, at least, effervescing steels are in a class by themselves and include steels made for boiler, tank, and ship plates, steel pipe, soft steel wire, wire nails, soft machincry, and structural steels. These are all low-carbon steels with less than 0.40 per cent. carbon. Low-carbon steels that do not effervesce but are killed are also made; these are put into ingots and castings but they are outside the limits of this paper. Effervescing steel is cast into square or slab molds, either top or bottom poured. Most of the effervescing steel is made in the basic open-hearth furnace, though much is made by the acid Bessemer process and a little is made in the acid open-hearth. It is not made by the crucible or electric-furnace process, in which the volume of gas required cannot be produced in the steel and evolved from it in the mold to give the effervescence desired. Any steel ingot, when teeming is finished, is of a certain size or volume. Leaving out of consideration for the moment the lessening of the over-all dimensions of the ingot through contraction due to loss of heat, the ingot may be placed in one of three classes: It may settle, losing in volume; it may stand, that is, remain constant in volume; it may rise, that is, increase in volume. Into which class an ingot will fall depends on the gases of the steel,

Jan 1, 1920

By J. A. Collins

THE process of plastic extension of face-centered cubic single crystal-line rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellae are free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [112] direction in the axis of the rod. This process has been checked in many face-centered cubic materials and readily permits the preparation of specimens that have been sub-jected to various determinable amounts of shearing action. It is clearly of interest to study in such measurably strained specimens the development of a recrystallized structure on annealing and if possible detect the source of nuclei from which the new crystals grow. Strain-annealing experiments of this character have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs, the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae) at the conclusion of a test of from 0.08 to 0.57. A particular point was made of determining the crystallite rotation, or small angular range assumed by the octahedral slip plane after these various amounts of shear. The mechanism of recrystallization and the magnitude and effect of recovery on the recrystallization process was investigated.

Jan 1, 1940

By W. H. Emmons

This paper is the second of a series treating the relations of ores of the metals to igneous rocks. In the first paper1 the general problem was outlined and the normal downward changes in metalliferous lodes were briefly stated, with references to earlier papers treating the relations of ores to depths of their formation. The present paper by a number of examples illustrates the relations treated in the first paper. These examples are chosen chiefly from the larger mining districts because their underground developments are more extensive, but the same relations are shown in maps of scores of undeveloped areas in which the main geological conditions are nearly similar. Ecology of Metalliferous Deposits Ore deposits are divided into three groups: 1, Those formed by sedimentary processes; 2, those deposited by meteoric waters; and, 3, those formed in connection with igneous processes. The last group is the most important. It includes the magmatic segregations, which are igneous rocks in the strict sense, and the veins and related deposits, which were formed by precipitation in channels from solutions originating in cooling intrusives. These deposits may be divided into two groups: 1. Those related to intrusives as basic as diorite; and, 2, those related to intrusives more acid than diorite. The second group probably includes more than 95 per cent. of all lode ores. Nearly all of the ores of this group are associated with granitic batholiths or are in positions where it is reasonable to suppose that such a batholith, not yet exposed by erosion, underlies the area containing the deposits. The batholiths are great masses of deep-seated igneous rocks. When they are intruded most of them are probably as basic as diorite and some

Jan 1, 1927

By W. C. Maurer

Although millions of feet of rock are drilled annually, the basic drilling mechanisms involved are not well understood. The primary reason for this lack of knowledge is because the basic principles of rock failure are not well understood and rock failure is the primary mechanism in drilling. A better understanding of the drilling mechanisms would enable a more scientific approach to the design and use of drills and bits. The paper reviews several models which have been proposed to explain various aspects of the different drilling methods. These models are described and their limitations and areas of application are discussed. Drilling rate relationships are developed and related to the basic rock failure mechanisms. TYPES OF MECHANICAL DRILLS There are three basic methods of mechanically attacking rock: 1) percussive action, 2) rotary action, and 3) combined rotary-percussive action. A percussion drill applies a force perpendicular to the rock surface and the bit moves into the rock perpendicular to the surface, forming a crater beneath it (Fig. 1). A rotary drill applies a constant thrust to the bit while a torsional force moves the bit parallel to the rock surface, breaking the rock ahead of it. A rotary-percussive drill applies both a rotary force and a percussive force to the bit which moves into the rock at an angle to the surface. The commonly used drills can be classified as: rotary-drag, diamond; percussive-hammer, piston, churn; and combination-rotary-percussive, roller.

Jan 1, 1967

By A. Weiss, W. A. Coster

The search for ore is characterized by a great variety of uncertainties, each of which can be resolved by obtaining information at a cost. Three exploration stages may be distinguished in which information can be obtained, based on inherently different cost structure: 1) the reconnaissance or scanning stage, 2) the examination or screening stage and 3) the project stage. This exploration sequence would roughly coincide with replies to questions as to: where, how, why and how much. As complete information in each stage is too costly to acquire, we must assess the probability that adequate information will be furnished by a limited amount of effort and attempt to maximize the expected value of ore to be found for a given exploration expenditure. Several problems are discussed relative to the mathematical formulation and possible computer procedures for determining the optimum allocation of a total exploration effort. Based on the available literature possible solutions to this problem are indicated. When scanning through published literature on mineral exploration, it seems at first that there is little room for substantial and systematic improvements in the efficiency with which the problem of discovery of new ore deposits is presently being handled by large organizations active in exploration. It appears equally difficult to offer something relevantly new which could generate a break-through in exploration thinking and cause a marked improvement in the ratio of successful undertakings to the total exploration projects started. On the other hand, a number of experts in recent years have urged that the problems in prospecting be analyzed in a more skillful and sophisticated manner than in the past. Their thesis is based mainly on the premise that the cost of finding mineral deposits will increase with increasing technical difficulties. In present large-scale exploration ventures, especially in those regions where outcrops and immediately visible geologic evidence are scarce, older methods of prospecting are increasingly being replaced by more indirect and systematic geophysical and geochemical methods with more emphasis on correct statistical design of exploration patterns. It is perhaps the oil industry which has made the greatest strides in developing statistically, well justified patterns in its search for oil; possibly because oil seepages, as indicators of the presence of oil, left off at an earlier point in time than did outcrops as indicators of base metals. Among the pioneers in the field of statistics and operations research, as applied to mineral exploration, the excellent works of Allais, Slichter, Koop-man, Mickey, de Guhnin, Krumbein, Griffith, Sichel, Krige, de Wijs, and Matheron may be mentioned. It should, however, be pointed out that three subjects of basic importance to the allocation of exploration efforts have so far received only scant attention in published literature, even by the aforementioned authors. In the first place, a more precise definition of the object of the search, i.e., a minimum-size orebody, seems to be outstanding. Secondly, a decision model is not a widely-discussed subject. Thirdly, no concentrated attempt so far seems to have been made to establish probabilities of the occurrence of economic deposits on a regional scale and to arrive at a slightly more accurate knowledge of the probability laws governing the deposition of ore. It is not the purpose of this paper to create new order in the complexity of uncertainties in which our decision processes in exploration necessarily have to be conducted. Rather, we intend to highlight some of the outstanding, hitherto unmapped territory, where diligent compilation and a utilization of present and historic data may statistically improve our chances of success. We hope that the contribution of this paper will lie in bringing allocation problems into better focus and in increasing the mineral industry's realization of the magnitude of the factors involved. THE MINIMUM-SIZE OREBODY The concept of target specifications for what constitute a minimum-size orebody in exploration is a rather variable one and depends to some extent on

Jan 1, 1963

By Frederick Laist

THE object of the construction and operation of the 80-ton leaching plant was to test out the leaching of sand tailings on a large scale and, if possible, determine a definite method of operation, and the best construction for the larger unit which is now being built. It was also of importance to obtain some practical data as regards cost items. The 80-ton plant was not expected to be a commercial success. A leaching process on such low-grade material necessitates the treatment of a very large tonnage.. Such a cost item as labor, for instance, is entirely out of proportion in such a small plant. The amounts of acid, salt, scrap iron, and fuel for roasting, however, are the same per ton in an 80-ton plant as in a 2,000-ton plant. These costs were definitely established. Also the percentages of extraction and grade of tailings were definitely determined for a large-sized unit. Following will be found the description of the plant, the method of operation and the results obtained. A -general view of the plant is given in Fig. 1. The bins consisted of one coal bin with a capacity of 30 tons, one salt bin with a capacity of 20 tons, and a "mill tailings" or feed bin which held 70 tons. The coal and salt bins were placed with their floor level even with the firing floor of the roasting furnace. The feed bin, to give it greater capacity, discharged about 12 ft. below this point, to a 12-in. conveyor belt, which, in turn discharged into a pug mill. This fed another conveyor belt, which discharged into the top hearth of the furnace. The furnace was an ordinary six-hearth MacDougall roaster, .20-ft. in diameter. It was equipped with two fire boxes, on opposite sides, the flames entering on the third hearth. An induced draft was obtained with a Buffalo blower, worked as an exhaust fan. Just above the top hearth was an annular flue around the whole circumference of the furnace. Slots at intervals of about 18 in. led from this flue down into the top hearth. The slots were 2 in. wide by 6 in. long. This annular flue proved rather unsatisfactory, as it tended to fill up with flue dust and choke the slots, thus cutting down the draft. The volume of gas through

Jan 8, 1914

By Eli T. Conner

My connection, under a commission from the Councils and Board of School Control of the city of Scranton, Pa., with a recent investigation of mine-caves and the resultant damages to surface-improvements, has led to the preparation, at the invitation of our Secretary, of the present paper. It is notorious that there are, in the anthracite-fields, frequent subsidences of the surface, due to the removal of the coal beneath. No particular attention is paid to such occurrences, unless they happen to injure surface-improvements. Many caves have happened in Scranton and its viciuity, which hare excited but little remark, since they have generally caused no serious damage. In August, 1909, a cave occurred in the Hyde Park section of the city, generally known as the West Side, which nearly destroyed school-house No. 16 and considerable adjacent property. Fortunately, there were no pupils in the building at the time; but the thought of the possible result, had the usual number of pupils and teachers been present, aroused the public to the gravity of the situation; and the School Board employed engineers to investigate the case. Two reports were made by separate sets of engineers, which differed in some particulars. These differences were pointed out in the public press and magnified, and the consequent agitation of the subject was taken up and greatly exaggerated by some of the metropolitan newspapers, giving to uninformed people the very erroneous impression that the whole city of Scranton was in danger of sinking into the bowels of the earth. All this tended to affect the credit of the city and to depress real-estate values. The matter was considered at a joint meeting of the Board of Trade, the Councils, and the School Board. The Hon. J. Ben. Dimmick, a former Mayor, suggested that it

Jan 1, 1912

By W. E. Keck, W. C. Lowry, G. C. Eggleston

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant' mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939

On August 22, 1966, just 20 months after writing sales agreements with Japanese steel mills, Hamersley Iron Pty Ltd made its first contractual shipment of 52,000 tons to Yawata Iron and Steel Co Ltd. As world news, the event was not spectacular. But to mining men it represented an astonishing achievement. Twenty months of feverish effort and the expenditure of more than $100 million had created a large open-pit iron ore mine, a crushing plant, storage and load-out facilities for sized ore, and a supporting township at Mt Tom Price; a 182-mile standard gauge railway; and port and loading facilities for a nominal loading capacity of 6000 tph as well as a port town, Dampier, on King Bay. The project was executed in the sparsely inhabited, arid, dissected-plateau country of the Hamersley Range in the northwest sector of Western Australia. Hamersley, 60% owned by Conzinc RioTinto of Australia Pty Ltd and 40% by Kaiser Steel Corp, holds sale contracts for ore and pellets valued at $770 million. The main contracts are with the Japanese, who are to be supplied with 65.5 million tons of ore during the 16 years from August 1966 to August 1982 and 18 million tons of pellets over a 10-yr period beginning in early 1968. Of lesser importance at this time, but presaging trends, are contracts for a total of nearly 1.5 million tons to be shipped to England and Western Europe during the years 1966-68. A pellet plant with a capacity of 2 million tpy is now under construction at Dampier and is to be on stream early next year. Another interesting project for which the plans are set, is a desalination plant for sea water to supply industrial requirements and potable water for the town of Dampier.

Jan 5, 1967

By G. C. Eggleston, W. E. Keck, W. C. Lowry

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant' mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939

By William P. Blake

In another paper I have described in general the close association of zinc-blende and iron pyrites in the ore-deposits of southwest Wis consin. These two minerals generally occur together at the same horizon, a sheet of one being overlain by a sheet of the other; and also the pyrites is disseminated through the blende to such a degree that the latter is rendered comparatively worthless for the produc tion of spelter. Ordinarily the pyrites, which is mostly the trimetric marcasite variety, occurs in about equal quantity with the blende and is separated by hand-culliug and chipping; but there are large de posits where the ores are so closely mixed that they can neither be separated by culling nor by any mechanical method. The specific gravity of the two minerals is so nearly the same that attempts often made to effect even a partial separation by jigging have proved un. successful. The smelters of zinc-ores in the Mississippi valley will not take ores which carry more than 7 per cent. of iron; and it is therefore necessary to cull the massive ('jack" with great care and at consid erable expense, in order to bring it up to the market-standard of purity. The results of trials to effect a separation of blende and pyrites in other regions have been equally unsatisfactory. The literature of this branch of metallurgy abounds in examples. In Wisconsin efforts have been made in the past to " burn " the mixed ores in heaps, in order to soften or destroy the pyrites, and facilitate its separation from the massive blende. The same method has also been resorted to when galenite is mixed through the substance of the blende, for the purpose of disintegrating the ore, so that it could be separated by jigging. The custom was to pile the ore and the fuel together. As might have been expected, the results were far from satisfactory. As is usual in heap-roast ing, some portions of the ore were overheated and decomposed; zinc was lost by volatilization; the galenite in some portions was

Jan 1, 1894

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,' and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6'7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.' EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.' Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969

By L. A. Panek

Using an approach based on the theory of similitude, the author develops a general equation and related concepts that provide new insights to an old problem. The load-bearing capacity (strength) of a square, rectangular, or cylindrical prism of a brittle material such as rock, coal, or concrete is expressed as the mathematical product of a size effect, a shape effect, and a function of the mechanical properties (deformability, cleat/joint spacing, and friction) of the pillar, roof, and floor materials. Through an application of multivariate statistical analysis, the results of assorted tests (laboratory and in situ) and observations of failed pillars can be combined into a fundamental scaling equation, which provides a unified, consistent approach to the estimation of mine pillar strength. The form of the equation is sufficiently general to be able to incorporate refinements in the characterization of the structural parameters, as they become available through future analysis and experimentation. Analysis of the published test data suggests that pillar compressive strength (per unit of area) is proportional to the cube root of the pillar width, and that the height effect can be described as the superimposing of a variable size effect (characteristic of the material) on the constant width effect.

Jan 1, 1981

By Fred Bond

This paper is a continuation of two earlier papers,1,2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a. new method of measuring the "surface energy" of in ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems.

Jan 1, 1938

By Fred C. Bond

AN improved method of measuring the surface area of a comminution product down to any desired particle size has been developed. The method is largely graphical, and requires relatively little calculation. It can be used with materials containing large amounts of clay, or excess fines of any kind. The surface area S is expressed in terms of square meters per100 c.c. of solids. This expression is based upon volume rather than weight, and is considered to be more suitable for crushing and grinding problems, where the machines ordinarily are operated under constant volume conditions. It has the advantage that surface areas of different materials can be compared directly, even though their specific gravities may be unknown. The "specific surface" of a material, or the number of square centimeters of surface area per gram, is equal to 100S divided by the specific gravity. Particle diameters are expressed in microns, K being the diameter of the largest particle present and L the grind limit, or lower size limit of the particles formed directly by grinding. The value of K does not always coincide exactly with the diameters of the largest particles retained on the coarsest testing sieve, since the largest particles formed in crushing and grinding are often slabby, or have other irregular shapes. L has been chosen as 0.700 microns, or number 27.5 in the size number series,1 for reasons to be explained later. S is the total surface area of all particles larger than L microns in diameter. When a homogeneous comminution product is separated into fractions whose diameters bear a constant geometrical relationship [p] to each other, and the log per cent weight retained upon each size and passing the next larger size is plotted against the log diameter, a straight line results, which is called the distribution line, and which has a slope in called the distribution modulus. The distribution line can be extended to any desired limiting size, and the total surface area of all particles larger than that size can be calculated. The equation of the distribution line is w = Cxm [I] where w is the per cent weight retained on each successive sieve; x is the particle diameter; and C is the per cent weight retained on an opening of unit diameter.2 Theoretically, the distribution line can be extended to include infinitely small particles. When it is so extended, and the assumption is made that no fine particles are present other than those accounted for by the equation; the log per cent cumulative weight passing any series of sizes, plotted against the log diameter passed, will result in a straight line lying parallel to and above the plotted distribution line.

Jan 1, 1941

By George A. Morrison

The Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Bar-berton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITe The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 2 50 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. Geology The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft. are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1946

By F. L. Wolf

The catenary system of line construction possesses so many desirable characteristics from the operating standpoint that it has wide application for all types of electric traction. Many steam roads are electrifying sections of their lines, and in most cases are operating both steam and electric locomotives over the same track. This means that the overhead catenary system is subjected to the severe corrosive action of locomotive smoke, and data concerning the resistance of various alloys to this form of corrosion are very desirable from every point of view. Reliable and specific information and data on the subject of corrosion due to steam and smoke from locomotives are extremely meager and, on this account, extensive service tests, together with accelerated tests, have been made on a number of commercial metals and alloys. The observations and data recorded in this paper are the result of a preliminary test which was started in 1923 and which has been carried on to the present time. The recognition of the need for even more detailed and accurate data has resulted in the undertaking of another test which has been in progress for about a year. The result of this test will be published in due course. Some years ago The Ohio Brass Co. was asked by one of the large steam railroad companies to furnish data on construction details for a catenary system which it was considering for one of its divisions. The selection of materials which would give the necessary physical characteristics as well as withstand the severe corrosive action of locomotive gases caused electrical railroad engineers considerable concern. At that time, there were available no specific or authentic data on these important questions: no systematic investigation of the problem appeared to have been made, even though it's importance was generally recognized. Such observations as had been made were crude in that they had been limited largely to visual inspection which too frequently is most misleading. However, the scattered information which was collected gave important clues as to how best to start an investigation. Technical literature was studied, metallurgical experts were consulted, and the problem was discussed with engineers who were in close contact

Jan 1, 1930

By Richard L. Ash

7.3-1. Introduction. All phases of mining competent materials are affected directly by the results achieved from primary blasts. It is imperative that their design suit each particular set of mining conditions. In general, the round design must provide an adequate tonnage of material, properly placed with suitable fragmentation, to ensure that loading, haulage, and subsequent disposal or processing are accomplished at the lowest possible cost. Blasting rounds are designed by the proper application of cratering relationships developed for the single, concentric, confined explosive charge. Blasting for surface mining and most open-cut heavy construction, however, is characterized by the use of rounds, composed of a number of explosive charges with relatively long lengths, which are placed in benches with specific finite dimensions. Therefore, modifications must be made to the classical, single point-charge cratering concepts. It is the purpose of this discussion to outline the basic principles, significant variables, and procedures for their integration in the design of rounds that are applicable to conditions characteristic of surface mining. Because relatively insensitive blasting agents will be used in most instances, particular attention must be given to priming, control of confinement, and selection of charge diameters that ensure complete explosive-reaction execution. 7.3-2. General Considerations. The primary requisites for any blasting round are that it ensure optimum results for existing operating conditions, possess adequate flexibility, and be relatively simple to employ. It is important that the relative arrangement of blastholes within a round be properly balanced to take advantage of the energy released by the explosives and the specific properties of the materials being blasted. There are also environ- mental and operational factors peculiar to each mine that will limit the choice of blasting patterns.

Jan 1, 1968

By E. Orowan

LONG before the role of dislocations in the plastic deformation of crystals was recognized, the stress-strain field around dislocations received considerable attention in the theory of elasticity. It seems that Weingarten1 was the first to consider dislocations as simple and typical sources of internal stress in elastic solids, and Volterra2 and Timpe3 investigated their elastic field. Fig 3-1 shows the two basic types of dislocations considered by Volterra. The first arises by making a straight-edged .plane cut in a solid, displacing the two surfaces of the cut in their own plane relatively to one another by a constant amount in a direction perpendicular to the edge, and welding them together; this is shown in Fig 3-la, where the outer cylindrical surface represents the boundary of the solid, and the thin spiral cylinder around the edge of the cut has been removed in order to avoid infinities of stress and strain. The second type of dislocation is shown in Fig 3-lb; here the surfaces of the cut have been displaced relatively to one another by a constant amount parallel to the edge, and then welded together. After J. M. Burgers,4 these two types are called edge and screw dislocations, respectively. They represent simple limiting cases; in the general case, the surfaces of the cut are displaced by a constant vector that lies in the plane of the surface but has components both parallel and perpendicular to the edge of the cut. This vector is the Burgers or slip vector. The name “dislocation” was given by A. E. H. Love;5 it was bor-

Jan 1, 1954