Search Documents

By G. Thomas, O. Johari

MEIERAN and Richman' have proposed a method for the determination of electron-diffraction patterns from twinned bcc crystals. It is the purpose of this note to present a general method capable of predicting the positions of all reflections from both matrix and twin regions for all possible orientations of cubic crystals. The method has been verified for twinning in explosively deformed copper, and is found to be a very useful tool when used in conjunction with stereographic projection, and dark-field electron microscopy. Let an isometric crystal be twinned in any (hkl) plane. The twinning can be considered either as a reflection in the twin plane or as a 180-deg rotation about the twin axis. In reciprocal space, the 180-deg rotation about the twin axis would place a given point p, q, Y to a new position P, Q,R, such that both will be equally inclined to the twin axis. This is represented in Fig. 1. If the coordinates of three such pairs of points are determined, the matrix of the transformation can be obtained.' It is also seen that such pairs would satisfy another condition, i.e., the vector [p,q,r] plus the vector [P,Q,R] will yield a multiple of hkl, i.e., the indices of the twin plane, because in isometric systems the axis [hkl] is perpendicular to the plane (hkl). This can be simplified by taking the points along the three axes. If a point h2 + k2 + 12, 0, 0 is taken along the x axis, it is seen that its new indices should be so as to yield a sum 2h2, 2hk, 2hl,i.e., 2h(h,k,1). (Also the points h2 - k2 - 12, 2hk, 2h1, and h2 + k2 + 12, 0, 0 are equidistant from the origin and both points make equal angles with the twin axis, i.e., cos-' h/dh2 + k2 + l2.) Similar operations for the points yield respectively, after the 180-deg rotation about the twin axis. Following the method due to Buerger,' the matrix of the transformation is obtained as follows: Using this matrix the indices of any other point in reciprocal space can be determined. This matrix is much simplified for (111) twinning commonly encountered in fcc metals, since are each equal to —1; hence

Jan 1, 1964

By D. N. Dietz

A method for determining average reservoir pressure is presented, which is simpler to apply than that devised by Matthews. Brons and Hazebroek. For bounded reservoirs, identical results are obtained if stabilized-flow conditions prevail. The present method yields inferior results in the transient state. The method can, with a slight modification, also be used for water-drive reservoirs. INTRODUCTION In the method proposed by Matthews, Brons and Haze-broek' for determining average reservoir pressure in a multi-well reservoir, the cumulative production (the production time of each well) enters twice: once when the buildup is plotted against In (t + t)/At to arrive at p*, and a second time when the correction, p*-p is determined with one of the several formulas for differently shaped drainage areas. Once a steady state has been attained, however, the previous production history should be immaterial. The same pressure distribution could have been arrived at after different cumulative productions of the individual wells. In principle, therefore, it should be possible to determine average pressures without referring to cumulative productions. In the following paragraphs an expression is presented for the difference between the pressure in a producing well and the average pressure of its drainage area. Then the build-up time needed to overcome this difference is indicated. CASE OF A CIRCULAR DRAINAGE AREA AND A CENTRAL WELL PRESSURE DISTRIBUTION BEFORE SHUT-IN The general differential equation of radial flow (see Muskat, Eq. 10.2) may be written In the steady state, the rate of production of the well is equal to the rate of expansion of the fluid contained in the the drainage area; thus

Jan 1, 1966

The Pinson Mining Co., which will start production in very early 1981, is the fourth Carbon-In-Pulp plant to be put into operation in the United States. The property is located in Humbolt County, Nevada, 38 km (24 miles) northeast of the town of Golconda. The famous Getchell Mine was also near Golconda and was the site of one of the early Carbon-In-Pulp plants in the 1940s. The deposit was discovered in 1971 by Reno based Cordilleran Explorations, which is founded by a consortium of Canadian mining companies. Cordilleran is a partnership consisting of John Livermore and Peter Galli. In 1972 a second but smaller deposit, called "Preble", was discovered at a location 15 miles south of Pinson. During 1980, a decision was made to place the Pinson deposit into production and Pinson Mining Company was formed. Ownership of Pinson is vested in Lacana Mining Inc. , Rayrock Mines, Inc. , Siscoe Metals, Inc., John S. Livermore, Peter E. Galli and Donald M. Duncan. Three distinct but connected ore zones occur at Pinson. Combined reserves of milling ore total 3, 200, 000 tons at an average (undiluted) grade of 4. 12 g per mt (0. 12 oz per st) Au. Initial mining will be from "A" zone which contains 1, 500, 000 tons with an average (undiluted) grade of 5. 8 g per mt (0. 17 oz per st) Au. An additional 5, 500, 000 tons of low grade ore will be mined from the Pinson deposit and processed by heap leaching. Mining reserves at Preble total at least 1, 500, 000 tons grading 2. 7 g per mt (0. 08 oz per st) Au. Production plans for the Preble deposit have not been formulated at the date of writing. Gold mineralization at both deposits is finely disseminated as sub micron sized particles. The ore at Pinson is structurally controlled and occurs in an Ordovician limestone-siltstone unit. Much of the ore has been silicified to a jasperoid. The ore zones have been entirely oxidized. Preble ore occurs in the Cambrian formation in a carbonaceous, limey shale. Only the upper part of the Preble is oxidized and amenable to conventional cyanide leaching. The Pinson ore body is adjacent to the mouth of Granite Creek in the Osgood Mountains at an elevation of 1, 615 m (5, 300 ft) with the mill being 1. 2 km (3/4 mile) from the mine at an elevation of 1, 495 m (4, 900 ft). Mine development work began in May of 1980 with ore being stockpiled for later processing. Pertinent factors affecting

Jan 1, 1981

By S. Le Fevre

The application of electricity to the mining and beneficiation of the magnetic iron ores of the Mineville, N. Y., district, on Lake Champlain, has resulted,in economies and enhanced quality of product, without which only a comparatively small quantity of the present output could be marketed. The output of the Witherbee, Sherman & Co. mines is about 700,000 tons per annum, and of this about four-fifths is treated by magnetic separation to increase the iron content and reduce the phosphorus. The use of electricity for the magnetic separation of the ore from the gangue is therefore of primary importance, and makes possible the application of electric power for mining and preparing the ore for concentration. The fact which speaks loudest in favor of the application of electricity is this: It is possible for about 25c. per ton of shipping ore to furnish all the power required to put the ore on cars. This includes mining a hard ore underground, from a depth of 900 ft., hoisting to surface, crushing to $ or 8 in. in size, and separating from the gangue. This also includes lights about the works, and all miscellaneous power, such as about the shops. The first plant for the generation of electric power for use at Mineville was completed in 1903, and was one of the first for the application of electricity to mining iron ore. This was a Nordberg compound condensing steam engine, direct connected to a 750-kw. alternating-current generator, 3,300 volts, 3 phase, 25 cycles. All the plants added later use the same current but with higher voltage. The map, Fig. 1, shows the power plants and the transmission system; Figs. 2 and 3 are views of the shaft houses and the mills. The power from the first plant was distributed to Mills 1 and 2, one 2,500 cu. ft. compressor, and to the Harmony hoist, which was driven by a 300-h.p. motor operating four 10-ft. drums. Our experience with the hoist covers largely the development of electric hoisting from 1903 to date, and in some cases improvements were worked out to satisfy our needs. The motor is still operating as installed, but the control apparatus has been radically changed several times. When installed, the iron re-

Jan 1, 1915

By K. L. Young

The general energy equation, including change in kinetic energy, was solved by numerical integration and used to evaluate simplifying assumptions and application practices over a wide range of conditions. When extreme conditions were encountered, sizable errors were caused by large integration intervals, application of Simpson's rule and neglecting change in kinetic energy. A maximum error of only 1.31 percent was caused by assuming temperature and compressibility constants at their average value. It was discovered that a discontinuity can develop in the integral for the injection case. This discontinuity indicates a point of zero pressure change and is an inflection point in the pressure traverse. INTRODUCTION When a pressure in a gas well is to be calculated, one of the first decisions is to select a method of calculation. In many instances, this selection becomes a problem because the literature, at best, provides an evaluation of any method for only a limited range of conditions. Once a method has been selected, a question often arises as to the size of the calculation interval which should be used. The question regarding calculation interval arises because an analytic solution is not obtainable and approximate solutions must be used. This paper presents an evaluation of major assumptions and application practices of probably the two most widely used methods for calculating steady-state single-phase gas well pressures. The two methods are Cullender and Smith1-" (numerical integration), and average temperature and com-pressibility. The Cullender-Smith method assumes that change in kinetic energy is negligible and is normally applied in two steps with a Simpson's rule correcton. The average temperature and compressibility method, in addition to neglecting kinetic energy change, asumes that temperature and compressibility are constant at their average values. This method is normally applied for wellhead shut-in pressures of less than 2,000 psi, and in one step. Computer programs were written to compute bottom-hole pressure with and without the assumptions, using various approaches. Values of input parameters investigated are shown in Table 1. Flow rate was limited to a maximum of 5,000 and 10,000 Mcf/D for tubing sizes of 1.610 and 1.995 in. ID, respectively. Flow rate was also limited to 10,000 Mcf/D for a tubing size of 2.441 in. ID when wellhead flowing pressure was 100 psia. These limitations were imposed on flow rate so as not to exceed sonic velocity. The z factor routine available necessitated limiting bottom-hole temperature to 240F and wellhead pressure to 3,000 psia. Pressures were compared on the basis of percent deviation from the trapezoidal integration of Eq. l or 2 at 100-ft intervals. A preliminary investigation indicated that a 1,000-ft interval solution would differ from a 50-ft interval solution by less than 0.25 percent; therefore, the 100-ft interval was chosen for a base. For the purpose of comparison, deviations less than 1 percent were considered insignificant. where 111.1 qeC2/d p = kinetic energy term. Eqs. 1 and 2 can be evaluated numerically at specific depths using the trapezoidal rule as shown by Cullender and Smith. If change in kinetic energy is neglected and temperature and compressibility are assumed constant at their average values, Eq. 1 can be integrated to give the average temperature and compressibility equation,

By R. E. Hummel, J. W. Koger

SINCE the first report about a diffusionless transformation of bcc p1 brass to tetragonal p" in 1936 by Kaminski and Kurdjumov,' a series of papers have been published about this transformation, mainly dealing with the temperature range of the martensitic-start temperature (M,) and with the crystallographic structures of the parent and product phases .s In the

Jan 1, 1969

By Nicholas J. Grant, Italo S. Servi

SPECIAL polishing and etching techniques were developed during an investigation of the high temperature mechanical properties of high purity aluminum (99.995 pct Al).* Electrolytic polishing was done successfully in the following electrolyte: 5 ml perchloric acid (72 pct), and 95 ml glacial acetic acid. No special precautions need be taken during the preparation of the electrolyte since no appreciable heat of mixing is evolved. Although the electrolyte is not an explosive, it is recommended that Jacquet's safety rules' be followed during the polishing operation. A voltage of 25 to 60 v gives a good polish in about 2 min at room temperature after preparation on 3/0 metallographic paper. Most of the grain boundaries are visible under the microscope after polishing. Since the current is controlled essentially by the resistance of the bath, it is necessary to keep the anode-to-cathode distance as constant as possible. Accordingly, polishing of irregularly shaped pieces will be difficult. A cooling bath and a stirring system are advisable in order to keep the temperature of the bath uniform and constant. Coarse-grained samples can be macroetched in a few seconds by lowering the voltage below 10 v. This is done after electrolytic polishing, without removing the sample from the bath, Fig. 1. The specimen can be repolished in less than 1 min by raising the voltage above 25 v. The "galvanic etching" technique, which has been described elsewhere,' was found to be helpful not only for macroetching, but also for microetching coarse-grained specimens. In fact, the different orientations of adjacent grains provide good contrast at the grain boundaries, when the sample is observed under polarized light. If the specimen is only partially etched, Fig. 2a, the grain boundaries can be located without completely destroying the appearance of the surface of the specimen. The unetched surface appears black under polarized light. Excellent color contrast is obtained by using a "sensitive tint" plate in the optical system of the microscope. In this case, the unetched surface has a magenta color, while the etched part of the sample assumes different colors varying from green to brown, according to the orientation of the grains. Etch pits were produced on high purity aluminum by using the technique suggested by Lacombe and Beaujard." Good results also were obtained by substituting 70 pct nitric acid for the fuming nitric acid recommended. This gave an etching reagent of the following composition: 70 ml nitric acid (70 pct), 50 ml hydrochloric acid (37.5 pct), and 3 ml hydrofluoric acid (48 pct). An example of the results is shown in Fig- 2b. The outline of the etch pits is revealed sharply if the specimen is observed under polarized light, as shown in Fig. 2c. These metallographic techniques are not suitable for the examination of commercially pure (2s) aluminum. References 'P. A. Jacquet: Metal Finishing (Nov. 1949) 47, p. 62. 21. S. Servi: Metal Progress (1950) 58, p. 732. 3 P. Lacombe and L. Beaujard: Journal Inst. of Metals (1947) 74, p. 1._________________________

Jan 1, 1952

By U. N. Bhrany, N. Arbiter

F. C. Bond (Consulting Engineer, Processing Machin-Dept., AllisChalmers Manufacturing Co., Milwaukee) This is a very comprehensive paper. It deals with 1) size distribution functions, 2) energy-particle size relationships, and 3) criteria for grinding efficiency. The method of analysis used consists of tracing the increase and decrease of successive Tyler scale screen fractions as grinding progresses. The treatment is based upon the assumption that the work done in grinding is concentrated entirely upon the coarse size fractions in the mill. It is postulated that when a feed consisting entirely of particles of one size fraction is batch ground that finer fractions increase at a constant rate as grinding progresses, until finally each in turn begins to be ground and to decrease in amount. It is shown that under these conditions the empirical Gates-Gaudin-Schuhmann log-log size distribution plot can be logically explained. It is difficult to imagine any condition of ball mill operation, or any probability analysis, which would result in no grinding contacts on the finer particles present. However, the authors' postulate must be accepted if their conclusions are to be sustained. They conclude that the equation expressing the for mation rate of each size fraction can be resolved into the G.-G.-S. size distribution equation, and that the curvilinear portion of the log-logsize distribution line represents the only particle sizes which are being ground as well as produced. The author's statement that the G.-G.-S. Eq. 4 applies only to the finer portion of the size distribution while the Rosin-Rammler Eq. 6 applies over the whole size distribution range certainly supports the view that an exponential equation of the Rosin-Rammler type corresponds more closely to actual size distribution than does the power law G.-G.-S. equation. However, the G.-G.-S. equation is used to derive Eq. 8 and Eq. 9, which state that the energy required to grind a ton through a particular mesh varies inversely as the particle size to the exponent -a , whic h is the slope of the extended G.-G.-S straight line. This is stated to apply to both batch and continuous grinding. The G.-G.-S. slope exponent thus becomes very important in all crushing and grinding analyses by this method. The authors include some data which can be used to test their conclusions, as described below: We will consider grinding a feed composed of 14 mesh (1190u) to -200 mesh (74u). The average of 17 Allis-Chalmers grindability tests on quartz gives a work index (Wi) of 12.77. The -200 mesh product should have 80 pct passing 41.6u or P = 41.6. The equivalent 80 pct passing size of the 14 mesh feed particles is considered to be the particle diameter, as is true for spherical particles. Thus F is 1190u. In the work index equation 10 wi 10 wi 127.7 127.7 P f 41.6 1190 = 16.1 kw-hrperton. In Table I the ball mill exponent for quartz is 1.0 and from Eqs. 9 and 10: w=kw-hr/ton =Constan/(do/di) = 16.1 ton so that (1190) Constant/ Constant and the Constant equals 259. The tons per horsepower-hour value is 0.0464, in agreement with Table IV. The exponents for other minerals are listed in Tabl e 11. In Table IIA, the kilowatt hours per ton required to grind these minerals between the same sizes as the quartz, both by the authors' method and the work index equation, are listed. According to the authors kw-hrperton = 259/(16.1)".

Jan 1, 1961

By E. J. MCOAUSTLAND

THE behavior of steel after overstrain and at moderate temperatures is fairly well known. It has been made the subject of much investigation, and our knowledge is clear and definite on many points. The ultimate raising of the elastic limit, after moderate overstrain, and the consequent lowering of the ductility, seem to be well established. It is also well understood that the immediate effect of overstrain is to lower the elastic limit, possibly to zero, but that if not interfered with, this limit will subsequently rise higher than before. The "tests after moderate temperature," reported in this paper, were undertaken to verify the above statements for the particular steel under investigation, and also to determine, if possible, the total time required for complete recovery from this state of overstrain. The behavior of overstrained steel at temperatures at or below 32° F. is not so well known. Tests made by Prof E. G. Coker, at McGill University,' show that steel, overstrained and subjected to cold, will remain in a state of overstrain for an indefinite period. I am not aware of any other published results of tests along this particular line. The effect of time and temperature on the recovery of steel from overstrain was made in 1902-3 the subject of sortie investigation in the laboratories of the College of Civil Engineering of Cornell University. A general plan was outlined in connection with the regular courses of instruction in testing of materials; but the press of routine work and the demands of the schedules on the time of the students were so great as to presage long delay in the completion of the work. Not much had been accomplished up to 1904-05, when Messrs. E. C.

May 1, 1906

By F. C. Smyers, E. W. Merrick

ALTHOUGH the zinc and pyrite concentrates produced at Midvale go to other companies, the United States Smelting Refining and Mining Company smelts and refines its own lead. Refining is the first step of the process that is done at some distance from the mining operations, the plant being at East Chicago, Ind., an industrial center about 25 miles southeast of Chicago. For years it has been notable as being the only lead refinery in the country using the Betts electrolytic process. The original buildings, many of which are still in use, were erected in 1906 when the plant was known as the United States Metals Refining Co. In 1920 the parent company sold its copper refinery at Chrome, N. J., and since the copper refinery was also known as the U. S.

Jan 1, 1948

By Clyde E. Williams

MODERN steelmaking has gradually evolved from an inefficient small-scale operation, utilizing tiny units, to a highly efficient one utilizing large units almost completely mechanized. The leading position of the United States in the steel industry is due to the possession of easily assembled high-grade raw materials and large-scale highly developed plants. Modern integrated steel operation is largely one of material handling. Mining and transportation of iron ore, coal, and fluxes, coking the coal in by-product ovens, smelting the ore with coke and limestone in blast furnaces, converting the resulting pig iron into steel in the Bessemer, or in the open hearth when supplemented with scrap, and fabricating the resulting steel ingots in the shapes of commerce all are done on a huge scale, mostly by machinery, most of the labor being employed either in operating the machine or keeping it in repair. At the same time the quality and uniformity of the product have been greatly increased by the development of scientific knowledge and operating skills. Thus, the steel industry in this country is highly developed both mechanically and technically.

Jan 1, 1942

By R. S. Schechter, T. R. Guilinger, P. Bobeck, J. G. Price, L. W. Lake

This paper presents the results of an experimental study on the rate of uranium and molybdenum extraction from a flow reactor. Specific variables tested are fluid throughput and flow rate, lixiviant cation, and injected pH and carbonate concentration. The ore tested was from the Felder mine in southern Texas. It contained substantial quantities of marcasite and molybdenum disulfide that competed with the uranium ore for oxidant. Flow studies showed the oxidation of molybdenum disulfide under field conditions is mass transfer controlled, whereas the uranium oxidation is limited by surface reaction rate. The rate of uranium oxidation decreased with decreasing pH. The total carbonate levels, on the other hand, were unimportant. Ammonium carbonate appears to greatly decrease, if not completely halt, the reaction of marcasite with the oxygen. This effect was not found using either sodium or potassium carbonate.

Jan 1, 1986

By William R. Rumbold

THE Kinta valley in the State of Perak, one of the largest of the Federated Malay States, is probably at the present time the richest alluvial tin-district in the world, Perak producing from 20,000 to 25,000 tons of tin annually, and the Kiuta valley being the chief producer. The valley runs approximately north and south, and is 30 miles long by 12 wide. It is very flat, the mountain-ranges on either side rising abruptly from the plain, that on the east being the great Central range of the peninsula, and that on the west a subsidiary range marked " Kledang " on the map, Fig. 1. The valley is drained by the Kinta river, which rises in the eastern mountain range and flows south to join the Perak river, being joined by numerous streams from both mountain-ranges. The rain-fall is heavy, averaging annually about 90 in. The whole country is covered with dense jungle, except where it has been cleared for mining-operations and a small amount of cultivation. Mining villages are scattered throughout the valley, the chief towns being Kampar, Batu Gajah, Lahat and Ipoh, the latter being the center of the mining-operations. An ideal section of the main geological features of the Kinta valley is given in Fig. 2. The valley is composed of a highly crystalline limestone, usually white in color, sometimes gray; in fact, it may be called marble. It is always highly inclined and often contorted, and in some places is interbedded with shale. On the east side of the valley, near its contact with the granite, it forms a remarkable series of limestone cliffs, which rise in some cases as high as 2,000 ft. above the level of the limestone in the valley. It is non-fossiliferous, and its geo-

Sep 1, 1906

By Harlowe Hardinge

AN extensive recent trip throughout the mining districts of the Southwest, Central West, an Northwest,' reveals a numbes of interesting conditions that have influenced operators, in both large and small mills, to modify their flow sheets insofar as they pertain to crushing and grinding. The changes made and planned for the future should be of interest. It is interesting to note when traveling through the country, how ideas change and practice is modified, and it is rather amusing to see how milling methods seem to run, more or less, in cycles. New ideas and developments are brought about which run through the industry and are taken up by many of the best and most well informed operators. Some of them will change, sooner or later, back to their old practice; for, like everything .else, what will work well in one place will not necessarily be suited to another. On the other hand, it is often difficult to establish. other practices known to be of value, owing to the natural resistance to make a change, but on the whole, the western mill men seem to be more alive to possible benefits of various modifications than any other engineers with whom I have come in contact in all parts of the world. Mill men in other parts of the world always keep in con- tact with what is being done in the western part of the United States, but it does not necessarily follow that those in the western part of the United States are always right. Some of these changes that have been made and afterward abandoned will be referred to later.

Jan 1, 1929

By S. C. Termes, P. E. Richardson, R. L. Wilfong

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble cross-linked starch xanthate (ISX). ISX is insoluble, has a shelf life of more than a year when kept cold, and has a higher molecular weight due to cross-linking than the soluble, non-cross-linked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines, but no silicious gangue. Floc formation, floc size, and settling rate are dependent on pH. The pH dependence, however, differs for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1984

Upon the recommendation of its Technical Committee, The Com-pressed Air Society has adopted the following definitions of, certain terms. Displacement.-The displacement of an air compressor is the volume displaced by the net area of the compressor piston. Capacity.-The capacity should be expressed in cubic feet per minute, and is the actual amount of air compressed and delivered, expressed in terms of free air at intake temperature and at the pressure of dry air at the suction. Volumetric Efficiency.-Volumetric efficiency is the ratio of the capacity to the displacement of the compressor, all as defined above. Compression Efficiency.-Compression efficiency is the ratio of the work required to compress isothermally all the air delivered by an air compressor to the work actually clone within the compressor cylinder, as shown by indicator cards, and may he expressed is the product of the volumetric efficiency (the intake pressure and the hyperbolic logarithm of the ratio of compression), all divided by the indicated mean effective pressure within the air cylinder or cylinders.

Jan 8, 1918

By Robert L. Zook, Bernard J. Olup, James J. Pierre

Coal refuse slurry impoundments are dams constructed of coarse coal refuse to impound fine refuse (slurry) and water (25 to 30% solids). Both products are waste from coal preparation plants. A number of these structures in West Virginia, Pennsylvania, and Kentucky were investigated to determine embankment stability. During the investigation a variety of embankment designs were encountered. The investigation determined the soil and geological characteristics of the embankments and the sites. This was accomplished by a test drilling and monitor installation (observation wells and piezometers) program, geologic study, and large-scale mapping which allowed subsurface profiles of the embankments to be constructed. The laboratory testing program concentrated on textural classification of the coal refuse, permeability, and determining strength parameters to be utilized in the stability analyses. For the stability analyses, the modified Fellenius slip circle, simplified Bishop slip circle, and analysis for translational failure were utilized. In all stability analyses hydrostatic pressure and seismic acceleration probability were considered. This investigation indicated that 62% of the embankments analyzed were in a stable condition. The coal seam, the type of roof rock, and the gradation of the refuse influence the degree of compaction obtainable and the permeability of refuse. The shear strength of coal refuse appears to be controlled by its composition, moisture content, degree of compaction, amount and grain size of fines present. This investigation demonstrated these embankments should not be treated as pure state-of-the-art dams consideration must be given to the particular properties of coal refuse and the total refuse disposal system. Refuse dam slurry impoundments generally lack the site selection phase that is standard practice with siting most other types of dams.

Jan 1, 1976

By G. D. Hobson, I. Mrosovsky

Material balance relationships for expansion-type reservoirs above the bubble point have been discussed in recent years by H. N. Hall and M. F. Hawkins, Jr. The former drew attention to the effects of rock compressibility, and the latter to the effects of the compressibility of any interstitial water. Hawkins derived a general relationship which took note of oil, water and rock compressibilities, and then by assuming first, the absence of interstitial water and secondly, no effects due to interstitial water or rock compressibility, obtained relationships symbolically of the same form as those previously derived directly by Hall. Hawkins defined his terms clearly, and noted an approximation, due to the omission of a term involving the product of two compressibilities, made in reaching his final equation. There is, however, possible ambiguity with regard to Hall's written definition of the oil production term. One interpretation would mean that the produced oil and initial oil-in-place, if both required as stock tank barrels, would be obtained by using different formation volume factors in the conversion in order to satisfy the conditions implicit in Hall's formulae. The other would involve an approximation which, if used, was not stated. In both Hall's and Hawkins' studies the effect of the approximation or inconsistency is very slight. Nevertheless, it may be justifiable to give a somewhat more consistent derivation, since the complexity of the final relationships is not thereby greatly increased. Let the initial pore volume be Vi and the volume after a pressure drop of Ap, V. Then V = V, (1 - ?p . cr), where c, is the rock compressibility expressed as change in pore volume/unit pore volume/unit pressure change, and is defined with the initial pressure as base. Suppose that the interstitial water saturation under the initial conditions is Sw. The total volume of interstitial water under those conditions will be ViSw. If the volume of the water after dropping the pressure by ?p is V., this will be given by Vw = ViSw (1 + ?p.c,w), the compressibility of the water being c, which is ex- pressed using the volume at the initial pressure as base. If Boi is the reservoir volume factor of the crude oil for the initial reservoir conditions, and B. the equivalent factor when the pressure has dropped by ?p, with N the initial amount of oil expressed as stock tank barrels. N.Boi = Vi - V,Sw If n is the amount of oil produced (in terms of stock tank barrels) as a result of the pressure drop ?p, the remaining subsurface volume of oil at the lower pressure will be Bw, and Bc can be related to the compressibi:ity of oil and the pressure drop, and if c, is the compressibility factor based on the initial conditions, The relationship derived by Hawkins was case to a standard at the lower pressure, while a term (Ap) had been dropped, because of its smallness arising from its dependence on the products of two compressibility factors. When there is no interstitial water and rock compressibility can be ignored, Eq. 1 reduces to:

Jan 1, 1957

By John V. Beall

Since the U. S. Metals Refining Co. works was established, around the turn of the century, near the town which is now called Carteret, N. J., it has grown to be a major producer of refined copper and the main source of that special brand known as "oxygen-free high-conductivity copper." Owing to the complex metallurgical problems arising from handling a variety of raw materials such as copper concentrate from Matahambre, Cuba, copper and brass scrap from the New York area, and domestic blister copper, the organization is geared from top management down through its 2000 employes to maintain a high degree of flexibility in plant operation. The Company is a subsidiary of The American Metal Co. Charges for the smelter furnaces, one reverberatory furnace and one blast furnace, are made up in. bedding bins so that they may be tailored to the production of a constant grade of blister copper. The reverberatory furnace smelts the .sulphide charge, which may be a blend of ten different materials but principally the Cuban concentrate, and the matte from the process is poured into a converter. This reverberatory is 80 by 20 ft, silica lined with a slag bottom, fired by pulverized coal, and continuously side-charged from the top by bottom-dump cars which keep the side walls covered. It produces a 40 to 50 per cent copper matte. The fuel-charge ratio is 4.35 tons of solid charge per ton of coal. The furnace has a capacity of 10,000 tons of charge per month and produces from 5000 to 6000 tons of slag per month which must be disposed of. About 5000 tons of converter slag is produced monthly and returned molten to the reverberatory furnace. The converter gases go through a spray chamber to a Cottrell precipitator and thence to the flue system. Smoke from the

Jan 1, 1948

By B. H. Bergstrom

The Gaudin-Meloy1 size distribution equation requires the evaluation of two constants, xo and r. The common log-log representation of a screen analysis as cumulative weight percentage passing versus size, readily yields the required constants as illustrated for curves A and B in Fig. 1. The 100% passing (y = 1.0) size is simply x,. If the straight portion of the curve be extrapolated to the 100% passing (y=1.0) abscissa, the intercept is the Schuhmann size modulus, k. The ratio of xo to the size modulus, k, is r as shown: The Gaudin-Meloy equation requires that the slope, a, of the size distribution approach unity in the finer sizes, as is the case for curves A and B. Often distributions are better characterized by slopes other than unity. The schuhmann2 equation is able to represent these distributions if the upper portions of the curves are ignored. Empirically, the Gaudin-Meloy equation can be modified to yield slopes other than unity by writing it as Here, a is the familiar Schuhmann slope, and xo is the 100% passing size. The value of r is still given by Eq. 2. Eq. 4 with its easily determined constants is more versatile than either the Schuhmann or the Gaudin-Meloy equations, since a wide variety of size distributions can be closely described. It is easier to fit than the Rosin-Rammler3 equation, and has the advantage that the top size, x,, is finite. REFERENCES A. M. Gaudin and T. P. Meloy: Model and a Comminution Distribution Equation for Single Fracture, AIME Transactions, 1962, Vol. 223, pp. 40 to 43. R. Schumann, Jr.: principles of comminution, I., size Distribution and Surface Calculations, AIME Technical Publication No. 1187, 1940. P. Rosin and E. Rammler: The Laws coverning the Fineness of Powdered Coal, J. Inst. Fuel, 1933. Vol. 7, p. 29.

Jan 1, 1967