Search Documents

By N. A. D. Parlee, N. M. El Tayeb

Fe-V alloys with small percentages of vanadium show no deviations from Sieverts' Law up to P~, = 1 atm in the 1600º to 1750ºC region. At somewhat under 8 pct V and up to at least 20pct V, at 1604" and 1661 °C, nitrogen absorption follows Sieverts' Law at low Pn2 values, but deviates from this law beyond critical values of pn2, due to formation of a nitrzde phase of approximately VN composition. The behavior below these solubility limits can be described at all temperatures by the equations: RAO and parlee1 suggested that the nitrogen absorption curve for liquid iron alloys takes the general form shown in Fig. 1 when an alloy nitride precipitate is formed. They showed that the precipitation of 6 titanium nitride from liquid Fe-Ti alloys follows this general scheme and dealt with the general theory involved. Recently, Evans and Pehlke2 reported their research on the precipitation of aluminum nitride from liquid Fe-A1 alloys. Fountain and Chipman's recent paper3 on the precipitation of boron nitride from solid solution contains a fine example of the analogous behavior which they have been studying in the solid state. Researches on the absorption of nitrogen by liquid Fe-V alloys have been described by various authors.1,4-7 Most of this work has been confined to fairly low vanadium concentrations and rather high temperatures because of difficulties variously described as, formation of surface scums, bridging, and so forth. This behavior and the rough thermo- dynamic calculations made by chipman,8 over eleven years ago, indicated that excessively high vanadium concentrations should not be required for vanadium nitride precipitation. It seemed desirable to look for and study this precipitation in order to fill out the thermodynamically interesting nitrogen absorption data on these alloys. EXPERIMENTAL METHOD The general method used was essentially the same as employed by Rao and parlee,1 in which a Sieverts type of apparatus was used and the precipitation of the nitride detected by the "break-point" in the Sieverts' Law line, and by the visual observation of the formation of the new phase on the surface of the melt. There were, however, a few differences in apparatus and technique as described below. The oil manometer used by Rao and parlee' to measure low partial pressures of nitrogen was not employed. The present authors sought to avoid as much as possible the exposure of the liquid alloy to low total pressures of gas during the 6 to 10 hr long runs because of the heavy iron evaporation-loss errors involved. This was achieved, partly by keeping evacuation times to a minimum with fast pumping but largely by the use of two burettes, one for argon and one for nitrogen, and using them to equilibrate the alloy with mixtures of argon and nitrogen rather than nitrogen alone. Each run involved a careful sequence of operations. After melting, de-

Jan 1, 1963

By T. S. Lundy, R. E. Pawel

Effects of short-circuiting paths on observed diffusion behavior in real crystalline systems are considered. It is concluded that experimentally measured diffusion coefficients may vary widely from values associated with true lattice diffusion to those appropriate for short-circuiting paths alone depending upon the conditions of the experiment and the sensitivity and completeness of the data. IN 1961 Harrison1 classified experimentally observed diffusion behavior in systems involving both lattice and dislocation-enhanced atomic transport into three categories. His types A and C were limiting cases where the measured diffusion coefficients using the usual serial sectioning techniques were representative of lattice diffusion (with only slight effects of dislocations) and dislocation-network diffusion (with only slight effects from lattice diffusion), respectively. In both cases A and C for a sectioning experiment in which the diffusion couple has the semi-infinite geometry and unidirectional diffusion takes place from a plane source located at the origin of the coordinate system, he pointed out that Gaussian penetration behavior should be observed. For case A the lattice coefficient should be slightly enhanced by dislocation contributions, and the model of Hart2 can be used to predict the amount of this enhancement. For case C the observed coefficient should be that for the dislocation network and have little or nothing to do with lattice diffusion. Hart's model in its general form is still applicable, but the apparent diffusion coefficient for this case is virtually independent of dislocation density. Harrison's case B is that for which non-negligible contributions exist for transport by both mechanisms and "the concentration distribution does not approximate to any simple form." With the possible exception of very low temperatures where diffusion distances approach atomic dimensions, any real diffusion specimen will in general show non-Gaussian behavior provided the data are complete enough to uncover it. Thus, a "complete" set of data for any real system cannot be expected to be totally amenable to treatment by a simple mathematical model which does not take into account the relative distribution of transport by the various modes or submodes. For a particular sensitivity of specimen analysis and at a given temperature of annealing if the concentration profile could be observed as a function of time, "the behavior will initially be type C, and will develop into type B. and ultimately type A".1 Thus, it appears that the type of diffusion behavior which is experimentally observed in a given system depends very much upon the particular experimental conditions and the particular tools available to obtain the data. Interpreted in this fashion, Harrison's classification refers not to the diffusion behavior as a whole but to the relative sensitivity of the method of examination and completeness of the data. In the present paper we will: 1) assume that the measured penetration behavior follows the same general classification as that proposed by Harrison; 2) give, for diffusion in tungsten, examples of the range of diffusion coefficients that it is possible to obtain in a single experiment; and 3) speculate that some arguments which consider the possibility of short-circuiting effects being responsible for "anomalous" diffusion in several bcc metals may have been discarded prematurely.3 Both monocrystalline and polycrystalline tungsten were used in this work. The former was obtained as triple-pass, electron-beam zone-refined 6.0-mm-diam rod from Materials Research Corp.. Orange-burg. N.Y. The latter was swaged, high-purity bar stock which was annealed for 2 hr at 2200°C and 10-9 torr to yield an average grain diameter of about 25 /i. The tracer Nb95 was received in oxalate solution from the Isotopes Division, Oak Ridge National Laboratory. Experimental procedures of specimen preparation, isothermal diffusion annealing, serial sectioning by anodizing-and-stripping, and y counting of the individual sections to determine the tracer penetration profile after a given diffusion anneal have been described elsewhere.4 However, it should be noted that the anodizing-stripping sectioning technique has the particular advantage for this research of permitting sectioning to be accomplished over a wide range of

Jan 1, 1970

By W. H., Bassett

IN January, 1926, the writer began a study of the commercial value of beryllium in its relation to copper. The purpose of the investigation was not to make a mere laboratory study of the characteristics of beryllium-copper alloys, but to determine under mill conditions the behavior of copper when alloyed with beryllium and when other metals were added to such alloys; in other words, it was considered important to know whether the alloy bars could be hot-rolled or cold-worked, and what limits in composition would have to be established for these two methods of working. Consequently, more stress has been placed on the practical application of the alloys in engineering and commercial use than on a discussion of the metallography of the specimens examined, although this part of the matter has not been entirely neglected. Credit should be first given to G. Oesterheld,1 who, in 1916, published the copper-beryllium equilibrium diagram. Fig. 1 has been copied from the original article with the simple substitution of English words. It will be noted from Fig. 1 that alpha solid solutions are formed, up to about 1.5 per cent. Be (10.5 atom.). The freezing-point curve, after falling from 4.2 per cent. Be (23.5 atom.), enters into a very complicated form over the entire beta region. There is a possible compound, Cu2Be, at about 6.5 per cent. Be (32.3 atom.). The pure gamma range extends from 11.2 to 12.2 per cent. Be. (46.5 to 49 atom.), after which the liquidus rises rapidly to 30 per cent. Be. (75 atom.). The delta solution extends from 25 per cent. to an unknown percentage of beryllium. There is a eutectoid point at 575" C., extending from 1.5 to 11.2 per cent. Be., the maximum time interval of which occurs at 6 per cent. Be. Below this line the beta solution is described as breaking up into alpha and gamma. Microscopically, the eutectiferous alloy thus formed closely resembles pearlite, and requires a high magnification for its resolution.

Jan 1, 1927

Although the 71 Minerals operation is now closed down and the operating data presented is almost five years old, it is well worth describing since it was the first heap leaching operation conducted on a primarily silver ore. Tombstone was discovered in 1877 by Ed Schieffelen; and it became one of the most famous mining towns in the West through the stories connected with Wyatt Earp, Doc Holliday, and the Clanton brothers. Like many silver deposits .in the western United States, the Tombstone ores were relatively shallow. Several million ounces of silver were recovered in the relatively few years the camp was active; but mining virtually ceased by the early 1900s and was only continued in a small way until the 19409, a history similar to that of Tuscarora. The 71 Minerals operation was started in May 1975 and continued until late 1978 within the city limits of Tombstone on waste dumps; one was the' Lucky Cuss, Schieffelen's discovery, which had accumulated from the old underground operations. This waste material was mostly less than 50 mm (2 in.) in size, although there was some larger lumps. The grade was about 34 g Ag and 0.5 g Au per mt (1.0 oz Ag and 0.015 oz Au per st). The Tombstone dumps contained approximately 1,000,000 tons. The dumps and patented claims were held by a single owner, Tombstone Development Company, thus sufficient leaching material could be acquired from one source rather than dealing with a number of individuals, as is usual in putting together leaching ventures in old mining camps. 71 Minerals Ltd. was formed and a lease of the properties obtained. A site was selected close to the major mine dumps not far from down- town Tombstone. Pads approximately 90 m (300 ft) wide and 180 m (600 ft) long with an 8-degree slope were prepared using compacted old mill tailings as a base sealant on the pads. Mining was done at a rate of about 2,000 tons per day with a dozer, two scrapers, a front-end loader, and 30 ton trucks. The ore was dumped by the scrapers as it came from the dumps with no screening or crushing in 460 mm (18 in. ) layers and trimmed with the loader. Based on bulk sampling and laboratory testing, the majority of thegold and silver values were recovered within 30 days of leaching.

Jan 1, 1981

By AIME AIME

ENGINEERS in the past have been largely associated with private enterprise and there has been a considerable tendency on the part of some members of our profession to depreciate government service for engineers. We engineers must change our mental attitude about employment in government service, particularly in view of the present most friendly attitude of the U. S. Civil Service Commission toward engineers for major posts in our Government. We must also take a much more active interest in public affairs. It must be realized that the national-defense program, which we are now organizing, will require for its effectiveness large numbers of engineers skilled in a wide range of technical and administrative services. In fact, the success of this undertaking will depend largely upon the extent to which our Government can command expert engineering talent to serve during the emergency. There is an acute shortage of technical and supervisory engineering personnel not only in the industries concerned with national defense but also in the Army, Navy, and other defense agencies of the Government. By an Act of Congress, approved on Oct. 9. 1940. $9,000.- 000 was turned over to the U. S. Office of Education, the regular defense agency of the Government which has co-operated with higher education for

Jan 1, 1941

By L. Zwell, H. A. Wriedt

X-ray Lattice parameter and bulk density measurements were made at room temperature on solid solutions of nitrogen in purified a, iron, containing from 0 to 0.053 wt pct N. When nitrogen is dissolved in a, iron, the fractional increase in unit cell volume (X-ray diffraction) and the fractional increase in volume per gram of iron (bulk density measurement) are the same within experimental error. The two sets of results when averaged show that the unit cell edge of a, iron increases linearly by 3.2 X 10-2 A per wt pct N dissolved and that the partial gram-atomic volume of nitrogen at infinite dilution in a, iron is the same as it is in nitrogen-martensite, that is, 5.90 cm3. RECENT reviews17' of literature dealing with the lattice parameter of ferritic iron-nitrogen alloys indicate that the dilating effect of dissolved nitrogen on the bcc unit cell of a iron is not known with confidence. Five investigations3-7 either revealed no effect of nitrogen or were inconclusive. Among other investigations, where quantitative data were obtained, the results of Osawa and Iwaizumi8 indicate too large an effect, and those of Eisenhut and Kaupp9 show the lattice parameter of ferrite varying with the nitrogen content at concentrations far beyond the known solubility limit. It is not clear in Burns'10 data what value should be used for the lattice parameter of nitrogen-free ferrite in calculating the dilation. Burdese11 shares with Burns the shortcoming that the iron-nitrogen alloys were solution-treated and quenched with undissolved nitride present. The consequence is that the un- certainties in the solubility limit1 are added to those in the lattice parameter measurements when the variation of lattice parameter with nitrogen content is computed. For a system of such widespread interest, we felt that a new investigation was merited. Both X-ray diffraction and bulk density measurements were used to determine the dilation of the , a iron lattice by dissolved nitrogen. EXPERIMENTAL PROCEDURE Material. The bulk density and X-ray diffraction experiments were both made with specimens of a purified iron (denoted as "B iron")- from Battelle Memorial Institute. The impurity contents were as follows: As, C, Cu and Pb—50 ppm; Ag, Al, Co, Ga, 0, Ti-11 to 50 ppm; B, Be, Ca, Cd, Cr, Mg, Mn, Mo, N, Ni, S, Sb, Si, Sn, V, W-10 ppm or less. The vacuum-cast ingot was hot-forged and annealed. Pieces of the forged stock were machined and cold-rolled to give strip stock 0.08 and 0.002 in. thick for density and for X-ray measurements, respectively. Preparation of Specimens. Starting with a piece of the cold-rolled iron stock, the general sequence of operations, after an initial recrystallizing anneal, was to measure the density or lattice parameter, nitrogenize, remeasure the property, age or denitrogenize, and again measure the property. Duplicate analyses for nitrogen were made by a modified Kjeldahl method on portions of the actual density specimens and on pieces nitrogenized to equilibrium alongside the X-ray specimens. Annealing of the density specimens was performed by sealing the pieces with the as-rolled surfaces removed by filing into evacuated "Vycor" capsules and treating for 1 hr at 750°C followed by furnace cooling. (TO check the effect, if any, of annealing procedure, a specimen also was

Jan 1, 1962

By Roger E. Barthelemy

PRIMITIVE mining and metallurgy has today almost disappeared. Probably the only remaining tribal tin mining and smelting is practiced by the Laotian natives in one of the less known tin areas of the world. This district lies almost a thousand miles from the sea along the Mekong River, one of the longest rivers in the world, that marks the border between Siam and Laos, one of the five states forming French Indo-China. Less than twenty years ago it took more than two weeks' travel on elephant-back to reach the spot and today it still takes many days of travel, using all kinds of transportation from automobiles to native

Jan 1, 1938

By N. H. Emmons

(Canal Zone Meeting, November, 1910.) AN interesting development of copper blast-furnace construction has been brought about in adapting the blast-furnace to be a "burner" for sulphuric acid making. When the Tennessee Copper Co. first decided to construct an acid-plant, the standard type of brick-top furnace, supported by structural steel, was the only one in use at this plant. All the tests for temperature and strength of gas had been made on these furnaces, and had been satisfactory. When, however, the acid-plant was put on the flue, and the flue had to have a damper put in it to force the gas into that plant, troubles began. The furnaces were fairly tight, and for a few months the work was quite satisfactory., Fig. 1 shows the old type of furnace-top used at the start. It was soon found that this top would not stand the temperatures, particularly when dampered back, as was necessary to force the gas into the Glover towers. The structural steel, of which the furnace skeleton was constructed, warped and twisted so badly that it was not safe to use the furnaces. This effect is shown by Fig. 2, which is a photograph of old No. 4 furnace, after the brick-work had been removed. It became apparent that a new type of top was necessary and the engineering force was started oil the design of a new furnace-top, with the result that a low top, with brick-lined flues at each end below the feed-floor, leading to the main concrete dust-chamber, was constructed. This furnace, No. 7, is shown in Fig. 3. The charging-doors are made of cast-iron sections, three sections to a door, and three doors to a side. A door to the furnace was made of cast copper, but the heat was so great that the copper bent readily, due to the jarring of its * General Manager, Tennessee Copper Co.

Feb 1, 1911

By William A. Hustrulid

INTRODUCTION Prior to the mid-1970's, the U.S. Radioactive Waste Disposal Program was focused on salt deposits as the geologic medium of choice, almost to the exclusion of other rock types. These efforts are illustrated by the Project Salt Vault experiment in a salt mine at Lyons, Kansas, in 1965-1967 followed by attempts to locate a repository site in central Kansas. Preliminary evaluation of other geologic media led, in 1978, to the GAIN (Geotechnical Assessment and Instrumentation Needs for Nuclear Waste Isolation in Crystalline and Argillaceous Rocks) Symposium held at the University of California (Berkeley), for the purpose of preparing a state-of-the-art document together with research needs for some of the other possible rock types. Because possible sites had not been selected, nor would they be for some time, the primary emphasis was for research and development focused on generic rocks and generic sites. A basic ground rule at that time was that the host rock formation should provide the primary containment for the waste. Also, the U.S. Nuclear Regulatory Commission (NRC) was just drafting the proposed rules regarding site suitability so that this input was not available. The collection of baseline data, conduction of some critical experiments both in the laboratory and field, and the performance of scoping studies were deemed needed. Such work was indeed undertaken; and to date, a great deal of information has been compiled and much has been learned regarding the characteristics of rock masses, rock behavior

Jan 1, 1984

By E. W. Murbach

The oxidation of uranium carbide by oxygen at various pressures, and by air, has been investigated at temperatures up to 600°C. Arc-melted and cast uranium carbide displays oxidation behavior that appears to be dependent on its treatment after melting. ccReactive" uranium carbide, which results from exposure of freshly melted material to laboratory air, ignites in oxygen at about 275° to 350°C depending on pressure, and in air at about 350°C. The product of the initial oxidation appears to be UO2+.. Continued heating produces U30,. The initial oxidation rate is poportional, roughly, to the square root of the oxygen pressure. The activation energy determined for the initial oxidation reaction is 7.1 kcal, from 400° to 600°C in 10 mm of oxygen. AN investigation of low-decontamination methods for reprocessing uranium carbide reactor fuels is being carried out at Atomics International. One of the reprocessing cycles includes oxidation of the fuel at relatively low temperature (300° to 500°C) and reaction of the product oxide with carbon at elevated temperatures (above 1500°C) to produce uranium carbide. A number of small-scale experiments have been carried out in which uranium carbide was oxidized in air and oxygen at various pressures to measure reaction rates and to obtain other information concerning the oxidation process. In initial experiments with arc-melted UC, ignition was observed at about 275°C in oxygen or 350°C in air. However, similar experiments by Neymark' at 426°C in air showed no ignition. It was soon determined that the difference in oxidation behavior was due to the treatment of the UC following arc-melting. Neymark's experiments were carried out with freshly melted UC while those reported in the

Jan 1, 1963

By John W. Weeton, Donald W. Petrasek

Relatively few metal-metal systems exist that would permit the creation of fiber-metal composites consisting of mutually insoluble constituents. It is anticipated that most high strength-to-weight ratio and high -temperature fiber composites ultimately to be produced will utilize high-strength fibers embedded in a highly alloyed matrix. An investigation was conducted to determine the effect of alloying on the tensile Properties and micro-structure of tungsten-fibey-reinforced composites. Composites were made of tungsten fibers infiltrated with copper binary alloys that contain elements of varying solubility in tungsten. Room-temperature tensile tests were made on the composites, and a metallographic study of the microstructure of the fiber-metal-matrix interfaces was conducted. It was shown that, as the depth of penetration of some alloying elements into the fiber increased, a decrease in both tensile strength and ductility of the composite results. A notch effect, due to the formation of a brittle alloy zone with the tungsten fiber, was observed and gave rise to greater reductions in tensile properties and ductility behavior than would be Predicted by a law-of-mixture relation alone. In recent years, investigators have considered combining fibrous materials with relatively weak binder materials. The interest in fiber-reinforced composites results from the fact that fibers or wires may be exceedingly strong and exhibit mechanical properties superior to those of the bulk materials from which they are derived. For example, tungsten wires drawn to less than 1 mil in diameter may have strengths of over 600,000 psi,' while steel wires ranging from 10 to 3 mils in diameter may have strengths of the order of 300,000 to over 600,000 psi.2 Both metallic and ceramic whiskers are known to have very high strengths. For example, iron whiskers have been shown to have strengths of 1.9 million psi3 and sapphire whiskers have been reported to have strengths of the order of 1.7 million psi.4 If all or part of the strengths of such fibers could be retained, subsequent to the incorporation of the fibers in an engineering material, a superior material could result. In previous work done at the Lewis Research Center, McDanels, Jech, and weeton5 demonstrated the feasibility of fabricating metal-fiber—metal-matrix composites that utilized the full strengths of the fiber and matrix materials. Tungsten fibers were combined with a copper matrix by a liquid-infiltration method such that the tungsten fibers were uniaxially oriented parallel to the tensile axis of the composite. A linear relation was established that related the tensile strength of the composite with the volume percent of the fibers. Mutually insoluble constituents were selected for the study so that the strength of the composite could be quantitatively related to the strength of the individual constituents. The fact that there are only a few metals that are mutually insoluble with tungsten, e.g., copper, silver, gold, and zinc, and that these either have low melting points, high vapor pressures, or poor oxidation resistance, makes it necessary to utilize other metals that are soluble in tungsten, where high-temperature applications are ultimately contemplated. It was anticipated that, for most practical fiber-reinforced composite materials, it would be necessary to use a fiber and metallic matrix that would have varying degrees of solubility for each other. A logical extension of the earlier work was thus felt to be a study that would determine the effects of elements that had mutual solubility with the tungsten. Numerous investigators have found that tungsten fibers may be damaged by thermal treatments or contamination of the surface of the fiber by alloying elements.6-10 On the other hand, surface treatments may improve the strength of such fibers."-" Relatively little work with composites containing tungsten fibers have been reported. The work of parikh14 has shown that kinked, short-length tungsten, steel, and molybdenum fibers could str'engthen such matrices as silver, gold, and copper. Some of the combinations of fibers and matrices studied by

Jan 1, 1964

Executive ARTHUR S DWIGHT, Chairman B THAYER CHARLES F RAND P MATHEWSON J V W REYNDERS Membership WILLIAM H BASSETT, Chairman W Y WESTERVELT Vice-chairman P MATHEWSON H G MOULTON F T RUBIDGE Finance WALTER H ALDRIDGE, Chairman GEORGE D BARRON GALEN H CLEVENGER

Jan 1, 1923

By R. J. Fruehan, F. D. Richardson

Electrochemical measurements have been made of the activity of oxygen in copper and its alloys with silver and tin at 1100" and 1200°C. The galvanic cell used was Pt, Ni + NiO/solid ellectrolyte/[O] in metal, cermet, Pt The results do not support any of the equations so far designed for predicting the activities of dilute solutes in ternary solutions from activities in the corresponding binaries. If, however, a quasichemical equation is used with the coordination number set to unity, agreement between observed and calculated activities shows that this empirical relationship can be useful over a fair range of conditions. SEVERAL solution models have been proposed for predicting the activity coefficients of dilute solutes in ternary alloys from a knowledge of the three binary systems involved. Alcock and Richardson1 have shown that a regular model, and a quasichemical model,' in which the dissolved oxygen is coordinated with eight or so metal atoms, can reasonably predict the behavior of both metal and nonmetal solutes when the heats of solution of the solute in the separate solvent metals are similar. But when this is not so, neither model gives useful predictions unless coordination numbers of one or two are assumed. Wada and Saito3 subsequently adopted a similar model to derive the interaction energies for two dilute solutes in a solvent metal. Belton and Tankins4 Rave proposed both regular and quasichemical type models in which the oxygen is bound into molecular species, such as NiO and CuO in mixtures of Cu + Ni + 0. However, their models have only been tested on systems in which the excess free energies of solution of the solute in the two separate metals differ by a few kilocalories. Ope of the reasons why more advanced models have not been proposed is because few complete sets of data exist for ternary systems in which the solute behaves very differently in the two separate metals. For this reason measurements have been made of the activities of oxygen dissolved in Cu + Ag and Cu + Sn. Measurements on both systems were made by means of the electrochemical cell, Pt, Ni + NiO/solid electrolyte/O(in alloy), cermet,Pt [1] The activity of oxygen was calculated from the electromotive force and the standard free energy of formation of NiO, which is accurately known.5 Before investigating the alloys, studies were made of oxygen in copper to test the reliability of the cell and to check the thermodynamics of the system. Of the previous studies those by Sano and Sakao,6 Tom-linson and Young,7 and Tankins et al.8,7 have been made with gas-metal equilibrium techniques; those by Diaz and Richardson,9 Osterwald,10 wilder," Plusch-kell and Engell,12 Rickert and wagner,13 and Fischer and Ackermann14 have been made by electrochemical methods. EXPERIMENTAL The apparatus employed was the same as described previously,9 apart from slight modification. The molten sample of approximately 40 g was held in a high grade alumina crucible 1.2 in. OD and 1.6 in. long. The solid electrolytes were ZrO2 + 7½ wt pct CaO and ZrO2 + 15 wt pct CaO; the tubes 4 in. OD and 6 in. long were supplied by the Zirconia Corp. of America. They were closed (flat) at one end. In one experiment with Cu + O, both electrolytes were used in the cell at the same time. The reference electrodes inside the electrolyte tubes consisted of a mixture of Ni + NiO. They were made by mixing the powdered materials and pressing them manually into the ends of the tubes, with a platinum lead embedded in them. The tubes were then sintered overnight in the electromotive force apparatus at 1100°C. By sintering the powders inside the tubes (instead of using a presintered pellet9) better contacts were obtained between the electrolyte, the powder, and the platinum lead. Troubles arising from polarization9 were thus much reduced. The electromotive force was measured by a Vibron Electrometer with an input impedence of 1017 ohm; the temperature was measured with a Pt:13 pct Rh + Pt thermocouple protected by an alumina sheath. The couple was calibrated against the melting point of copper. The cermet conducting lead of Cr + 28 pct Al2O3, previously found to be satisfactory9 for use with Cu + 0 was also found satisfactory with Cu + Ag + 0 and Cu + Sn + 0. Superficial oxidation was observed, but it did not interfere with the working of the cell. The reaction tube containing the cell was closed at each end with cooled brass heads and suspended in a platinum resistance furnace. The tube was electrically shielded by a Kanthal A-1 ribbon which was wound round it, and the ribbon was protected by a N2 atmosphere between the furnace and the reaction tube. The cell was protected by a stream of high purity argon which was dried and passed through copper gauze at 450°C and titanium chips at 900°C. All the metals used were of spectrographic standard. Procedure. In studies of the system Cu + 0, be-

Jan 1, 1970

By AIME AIME

DURING the morning session," on Feb. 17, papers were presented and discussed regarding a recent wire saw installation, cement rock quarry operations, hydration factors in gypsum deposits and the status of the phosphate industry of the West. Oliver Bolvles presided and there were about twenty-five members present. W. M. Weigel's paper (T. P. 262), "The Application of the Wire Saw in Marble Quarrying," was read by the author. He described the recent installation of the St. Clair Marble Co., near Guion, Ark. Since the use of the wire saw for quarrying is comparatively new and the fact that it has been almost entirely limited to slate quarries heretofore, ?he description and data given in this paper were of much interest.

Jan 1, 1930

By P. E. Phillips

INTRODUCTION Rocky Mountain Energy is the mining subsidiary of the Union Pacific Corporation, and has been active m uranium exploration since 1966. Since 1970, RME's uranium activities have been funded 50% by Mono Power, the fuels supply division of Southern California Edision. RME and Mono recognized the need for development of new methods for recovering low grade uranium deposits, and contacted Halliburton Services in regard to in situ leaching, because of Halliburton oil industry experience. As a result, a joint venture between the three parties was formed in 1974. BEAR CREEK The first ISL test was at the Bear Creek deposit in the Powder River Basin of Wyoming, about 60 miles north of Douglas. The mineralized sand is the tertiary Wasatch formation, which is an arkosic sandstone. The sand typically contains about 10% clay. The predominant clay being montmorillonite with some kaolin and illite. The roll front type trends occur along the flanks of old stream channels. This deposit was being considered for exploitation as an open pit mine. Routine amenability testing indicated it was quite amenable to a conventional acid leach, consuming about 50 lbs. of sulfuric acid per ton of ore in an agitation leach, while recovering more than 95% of the uranium. Hydrology testing indicated a permeability of about 1 darcy. The groundwater has a pH of about 8. 0 and TDS of about 1200. Test Facility The Bear Creek test was a summer-only operation, with no effort towards weather-proofing. Uranium was removed from the recovered leach solution by fixed bed ion-exchange columns. Loaded resin was eluted with strong sulfuric acid. The recovery plant was designed for simplicity of operation, with little concern for the grade or form of the yellowcake product. The plant was constructed of PVC piping and valves, fiberglass reinforced tanks, and stainless steel pumps. All waste streams were directed toward a lined evaporation pond. Wellfield The test pattern was a 30 foot radius 5 spot, with wells fully penetrating the 30 foot ore sand to a total depth of about 165 feet. The injection wells were three-inch PVC with slotted casing, while the producer was eight-inch I. D. , with a stainless steel screen. The eight-inch well was necessary in order to accommodate a six-inch stainless steel pump. Wells were cemented using cement baskets, at the top of the sand, to contain a latex acid resistant cement. Leach Conditions The lixiviant generally contained from five to seven gpl sulfuric acid, and about 0. 5 gpl hydrogen peroxide. The pH was generally 1.4 and EMF was usually -550 millivolts. Injection rates were rather variable from well to well, with a total injection rate between 12 and 25 GPM. Production rate was set at 25 GPM, since the production pump could not be throttled more than that. Approximately two pore volumes of solution were injected during the three-month test. Leach Results Injectivity was quite variable, but was generally rather poor, because of poor completion techniques. The problem stemmed from injecting before the injection wells had been completely cleaned of drilling mud. Pregnant solutions averaged about 50 ppm U308, with groundwater dilution varying from 10 to 50%, depending on the injection rate. Injectivity did decline with time, probably as a result of contamination of the well faces. A total of 1000 lbs U308 had been recovered when the test was shut down. This probably represented about 10% of the mineral under leach.

Jan 1, 1979

By Charles H. Foreman

IN JUNE 1921, the Sullivan &lining Co., owned jointly by the Bunker Hill and Sullivan Mining & Concentrating Co. and the Hecla Mining Co, started work on the development of the Star Mine. The development work contemplated called for a crosscut from the Hecla workings on the 2000 level to the Star ledge. The length of crosscut necessary to encounter the Star ledge was approximately 8900 ft. from the Hecla shaft. By using workings formerly made by the Hecla Mining Co., only about 8100 ft. of actual crosscutting was necessary. This crosscut has a direction of S 20° W and would have a tendency to crosscut any ledges in the intervening ground.

Jan 1, 1924

By H. H. Otto

COMPARED with 1939, the year 1940 has seen no material change in the production of anthracite. Many factors seem to indicate a stabilized anthracite production of approximately 50 million tons per year. The present war has stimulated demand in the Cana¬dian and New England markets, which were formerly furnished with a portion of their needs from Great Britain and other European countries. Neither has there been any material change in the "bootleg coal" situation. This problem is more serious in the Southern anthracite field than in the Hazleton, Wilkes-Barre, and Scranton areas. One reason for this is the nearness of the Southern field to the large anthracite markets in Philadelphia, Washington, Baltimore, and Harrisburg. During the past year no new large

Jan 1, 1941

By Carl Scholz

Discussion of the paper of Carl Scholz, published in Bi-monthly Bulletin, No. 22, July, 1908, pp. 551 to 559. HOWARD N. EAVENSON, Gary, W. Va. (communication to the Secretary*) :-For some time before the publication of Mr. Scholz's paper, I had been collecting data bearing upon its subject, and I now take pleasure in presenting my results to the Institute in the form of a discussion. It has long been a matter of common opinion among mining-men that mice-explosions are, more frequent during the colder, or winter months, than during the warmer ones, and it is a matter of common knowledge among them that the air-ways and road-ways in most mines are much drier and are more in¬clined to be dusty during the winter than during the summer. In many mines, places which are wet and sloppy in the summer are dry and sometimes dusty during the winter. These changes, of course, can only be due to atmospheric conditions, and are caused by differences in temperature and humidity. Until recently, however, very little attention has been paid to the part that atmospheric conditions may play in mine-explosions, or, rather, to the effect they may have in rendering mine-conditions peculiarly dangerous, and in spreading and rendering more disastrous the effects of what would otherwise probably have been .small explosions. To show the difference in mine-conditions during sunnier .and winter months, I have tabulated in Table I. the results of 24 observations of hygrometric conditions in several different mines at different times of the year. Mines Nos. 1, 2, and 6 are located in the Pocahontas.coal -region, in McDowell couuty, W.Va., the first one being a shaft-mine shaft mine and the others drift. Mines 1A and 2A are drift-mines located in Logan county, W. Va. All of these are mines of fair size, but none of them has been in operation more than six years,

Jun 1, 1909

By Walter S. Weeks

THE subject of the flow of air through a mine under the influence of natural ventilation has proved an elusive one. To my knowledge only cut and try algebraic solutions have been used where multiple paths are involved. The object of this paper is to present a method for the graphical determination of the flow induced by the natural ventilation pressure (N.V.P.) alone or in combination with a fan. The N.V.P., measured in pounds per square foot, induced by two columns of air between two horizontal planes at different elevations, is equal to the difference in weight of the two columns, assuming each to have a cross-sectional area of 1 sq. ft. Pressure in pounds per square foot is converted into inches of water by dividing by 5.19. Methods of calculating the N.V.P. have been discussed in the literature. In this paper, for simplification of exposition, the change in pressure due to the weight of superimposed air will be assumed directly proportional to the length of the column. The actual methods of calculating the N.V.P. do not affect the solutions to be presented. It must be realized that the precision to be obtained from the small- scale, inked diagrams presented is not as great as would be obtained from large-scale, penciled curves that would be used in practice. The accuracy of the curves does not warrant reading "volumes" closer than the nearest thousand cubic feet per minute. CASE I. DUCTS IN SERIES The simplest type of problem is to determine the flow when two shafts are connected by a crosscut, as shown in Fig. 1. In this example, the resistance of the shafts is to be taken as 0.0001 in. of water for a flow of 1000 cu. ft. per minute for a length of 1000 ft. The resistance of a crosscut is to be taken as 0.0005 in. of water for a flow of 1000 cu. ft. per minute. The small pressures necessary to cause changes in velocity will not be considered, because the accuracy of other obtainable data does not warrant their consideration.

Jan 1, 1938

By ALEC CROWELL

Mississippi has had oil production for only the past six years and natural gas production of minor magnitude since' 1926. The search for oil and gas commenced in 1903 and 1496 wells had been drilled in search of oil and gas up to Jan. 1, 1946. As the year 1945 ended, 659 wells were producing oil and gas from 23 separate reservoirs. The production for the year was 8,353,719,000 standard cubic feet of natural gas measured on a pressure base of 15.025 lb. per sq. in. abs., 15.316,009 bbl. of oil¬field water and 19,093,766 bbl. of crude oil and condensate. Production for the year 1944 was 2,636,067,000 standard cubic feet of gas, 14,979,793 bbl. of salt water and 16,420,346 bbl. of crude oil and condensate.

Jan 1, 1946