Search Documents

By C. R. Sandberg, L. S. Gournay, R. F. Sippel

The effect of fluid-flow rate and fluid viscosity on oil-water relative permeability determinations was studied using the "dynamic flow technique." In this work relative per-nleability curves were obtained for homogeneous small core .samples from several sandstorle outcrop form-utions. Radio-tracers were used for the determination of fluid saturation and for the detection of saturation gradients. Cobalt-60 in the form of cobaltous chloride was used as a water-phase tracer in some of the experiments. Iodine-131 in the form of iodobenzene and Mercury-20-3 in the form of mercury diphenyl were used as oil-phase tracers in other experiments. Flow rates for each phase were varied within a range of 2.5 to 140.6 ml/hr. Oil-phase vis-cosities under flowing condition,> were varied from 0.398 to 1.683 cp. The relative permbilities ob-tained were found to he solely a function of saturation and independent of flow rare, provided there was no .Saturation gradient induced in the core sample by "boundary effect." Even though equilibrium with re-sped to flowing conditions was obtained at the lower flow rates, where a saturation gradient exists, this equilibrium is of a "contingent"-type rather than the "steady-state" equi-librium implicit in the relative per-meability concept. The only effect of increasing the oil or non-wetting phase viscosity was to decrease the flow rate required for the elimina-tion of the boundary effect. Fairly good agreement between experimentally determined and calculated values of the boundary effect was obtained when the non-wet-ring oil phase was the only Flowing phase. INTRODUCTION In the characterization of reservoir rock, as well as in the solution of reservoir production problems, it is most desirable to have reliablc rela-tive permeability measurements for the rock and fluids of interest. Many techniques have been developed for the laboratory determination of the relative permeability of both large and small core samples. In varying degree, difficulties attend the use of all of the methods. Each of the methods requires the metered flow of fluids of known viscosity through the core sample under conditions wherein the pressure drop in the individual flowing phases can be measured or closely approximated. Since the relative permeability is a function of the saturation and distribution of the flowing fluids, some means of obtaining such information is also required. The laboratory determination of the relative permeability of a sample should give the same relative permeability saturation relationship that would exist if the sample were in place in the oil reservoir. The attainment of this objective is complicated by the fact that the use of small core samples for laboratory measurements is usually necessary. As a result, errors in measuring the relative permeability arise from boundary effects at either the fluid input or output ends of the sample; no significant boundary effect is anticipated at the sides of the sample normal to direction of fluid flow. At the input end of the sample a boundary effect exists if the flow fluids are not com- mingled as they would be in the reservoir. At the output end of the sample a boundary effect exists as a result of discontinuity of the capillary properties of the system. Here the flowing fluids leave the small flow channels and enter a collecting system having much enlarged flow channels. Thus, there is a tendency for the wetting phase to be retained by the core sample because of the attraction of the core sample for the wetting fluid. No reference is made to these boundary effects in either Darcy's equation or in the relative permeability concept. As a consequence the saturation effect peculiar to the input end of the core sample may cause an error in the effective permeability measurement, since some portion of the core sample must be utilized for commingling of the flow fluids. At the output portion of the core sample a saturation gradient or a saturation change along the axis of flow results. Since relative permeability is a function of fluid saturation, this saturation gradient may cause a variable permeability measurement, especially since extent and character of the saturation gradient can vary with fluid-flow rate. The most convenient method of minimizing the boundary effect, especially at the output end of the sample, is to flow the fluids of interest through the core sample at such high rates that the capillary forces arc insignificant as compared to the viscous forces involved in the fluid flow. Since recent work of a preliminary nature has indicated that fluid dispersion in the porous medium increases with the flow rate, the high flow minimizes the boundary effect at the input end of the core sample by enhancing the mixing of the fluids.

By B. E. Sundquist

The various methods based on solution models for obtaining free energies of mixing from miscibility-gap data have been applied to a number of binary-alloy systems. For nine of these systems there exist experimental thermodynamic data that permit a comparison of the results to experiment. It was found that the method of van der Toorn and Tiedema almost invariably leads to results that are physically unacceptable and that vary drastically with small changes in the miscibility-gap parameters. The subregular solution model is found in all cases, except the Al-Zn, Fe-Cr, and Cu-Pb systems, to exaggerate the free energy of mixing by 30 pct or more. The model developed by Lumsden is found to give results that are often in excellent agreement with experiment and which exaggerate the free energy of mixing by no more than 30 pct. These results and others give evidence that the Lumsden treatment of the effect of unequal atomic sizes and of imperfect configurational randomness due to deviations of AB bond energies from the mean of AA and BB bond energies is adequate for most systems. ANALYTIC expressions are frequently proposed for the dependence on composition of the activities of the components of a solution. Because the development of solution theory is incomplete, these expressions contain parameters which must be determined by experiment. The measurement of activities is often difficult and consequently such measurements are less readily available than are measurements of phase equilibria which, under certain conditions, can also be used to evaluate these parameters. For example, suppose it is known that two structurally dissimilar phases, each of known composition, in an n-com-ponent system are at equilibrium at a given temperature and pressure. n equations can be set up in terms of these parameters expressing the equality of the chemical potential of each component in the two phases. In addition, one can write the Gibbs-Duhem equation for each phase that also contains these parameters. Thus, if these n + 2 equations contain n + 2 parameters, these parameters can be determined (at the temperature in question) from the phase diagram alone. If the average number of parameters in each expression for the activity of a given component in a given phase is V then there will be 2nV parameters involved. Equating 2nV to n + 2 shows that, for n + 2, V = 1. If the temperature dependence of each parameter were to be expressed in some explicit form one could use equilibrium conditions at a number of temperatures to increase V. The situation is much improved when the two phases in equilibrium are structurally similar. It can then be assumed that, stably or metastably, two phases will become one at higher temperatures. Thus the number of parameters involved becomes nV instead of 2nV. Hence, V = 2 for n = 2 using only one temperature. (It is implied here that the activity expressions used are valid over the entire composition range.) In this investigation only the equilibrium of two structurally similar, two-component phases (miscibility-gap systems) will be considered. The various proposed solution models will be applied to a number of these systems and the results compared with available experimental results. All of the analytic expressions that have been proposed for the free energy of mixing of a two-component system are of the form where ?Gmix is the free energy of mixing per mole of solution, N1 and N2 are the mole fractions of components 1 and 2, respectively, and f(Ni, T) is some function of composition and temperature. In the "ideal" solution model f = 0. In the "regular" solution model f = a constant. Since these two models permit only a symmetric equilibrium diagram they will not be considered further here. The simplest model that permits a nonsymmetric miscibility envelope is the so-called "subregular" solution model proposed by Hardy.1 This model gives where the Ci(T) are functions of temperature only. The same expression for f is obtained from the "linear a function" model proposed by Darken and Gurry2 and applied to miscibility-gap systems by Wriedt.3 This model requires that the a function defined by be a linear function of composition (yi is the activity coefficient of component i). This model is not purely hypothetical for it has been found2 to hold true for a number of systems. It is readily shown3 that the f(Nl, T) obtained from this model is of the form given in Eq. [2]. It will be noted that the subregular solution model contains only two parameters and hence both of them can be determined at any desired temperature below the critical temperature, Tc, for a miscibility-gap systems in the manner described previously. At T, the two constants can be determined by equating the second and third derivatives of ?Cmix with composition to zero. Another two-parameter model was proposed by Lumsden4 who set

Jan 1, 1967

By Roger N. Dokken

It is well-known1-4 that Fe-Si alloys from approximately 9 to 27 at. pct Si show an ordered structure of the Fe3Si type at room temperature. Recently Meinhardt and Krisement,' through an investigation of Fe-Si alloys at room temperature by neutron diffraction, discovered that at 10.8 at. pct Si ordering of the FeSi type occurs while above this composition the normal Fe3Si-type superstructure appears. This FeSi type of ordering was also found by Davies8 as indicated by X-ray diffraction measurements on an Fe-8.7 at. pct Si alloy. Meinhardt and Krisement7 extended their neutron-diffraction work and determined the phase-boundary temperatures for both FeSi- and Fe3Si-type ordering. Ordering phenomena can also be studied by resistance measurements.4,8-11 Krivoglas and Maty-sina" carried out a theoretical development of the

Jan 1, 1965

By Charles T. Holland, David A. Olsen

Considerable work has resulted in the development of a formula by which the strength of coal pillars for an L to T ratio of up to 12 may be estimated. One of the factors involved in this formula is the coefficient of friction between the coal pillar and the adjacent rock with which it is in contact. This paper presents the results of studies on sandstone, limestone, shale and coal and the coefficient of friction between coal and the other three under wet and dry conditions. With the coefficients of friction thus determined and the use of results obtained earlier by Meikle and Holland, it seems probable that coal pillar strength may be more closely estimated. Several investigators1-3 have found that the com-pressive strength of cubical coal specimens can be correlated by an equation such as

Jan 1, 1969

By Eizo Yabuuchi, Yukito Imanaga

INTRODUCTION In treatment of mine drainage, it is well known that the neutralization by calcium carbonate is far better than by slaked lime because of cheaper cost and better precipitability of its deposit. However, in case of iron ion contained in the mine drainage consists of ferrous salt, the ferrous salt must be oxidized to ferric salt before neutralization, because the ferrous salt does not react with calcium carbonate. At Yanahara Mine, during the period of 1950 through 1956, ferrous ion in the mine drainage had been oxidized to ferric ion, simultaneously neutralized by adding calcium carbonate into the aerated drainage. During the period of 1961 through 1974, after passing through many kinds of treating methods, the neutralization had been carried out by addition of calcium carbonate into the drainage after oxidized its ferrous ion to ferric by using nitrous gas as an oxidizing catalyzer. Meanwhile we had made an experiment on the oxidation of ferrous ion by utilizing iron bacteria, and developed a method which oxidized ferrous ion in large quantities briefly by cultivating and concentrating iron-oxidizing bacteria. Since 1974, we have been operating successfully for treating the drainage at Yanahara Mine by means of utilizing these bacteria.

Jan 1, 1976

By E. S. Machlin

THE function of this paper is to present certain results based on the fact that the strain energy arising from the solution of out-of-size solute atoms into the solid matrix is free energy and not internal energy, and that this strain energy is almost wholly shear strain energy as Zener1 pointed out. One natural consequence of this fact is an expression for the excess entropy of mixing due to the strain energy. Also, a derivation of the integral molar free energy of mixing partitioned to strain energy will be made using the model of Lawson2 and thermodynamics. This derivation has the advantage of showing in a simple way the assumptions involved in Lawson's treatment. The excess entropy of mixing partitioned to strain energy can be derived in two ways. The first way makes use of the fact that the strain energy is almost wholly in the form of shear strain energy. In this case, as Zener1 pointed out, the change in entropy due to the addition of shear strain energy is to a first approximation given by ?S/?? p,T = - ?lnµ/?T p,? Hence, the excess entropy of mixing partitioned to strain energy will be given by Sx ? = ?S/?? p,T Gx ? = - ?lnµ/?T p,? Gx ? where, Gx ? is the relative integral molar free en- ergy partitioned to strain energy; S is the entropy; is the shear strain energy; µ is the shear modulus; T is the absolute temperature; p is the pressure; and ? is the shear strain. Zener,1 as well as others, has pointed out that the shear strain energy stored in a compressible isotropic solid due to the insertion of an off-size incompres-sible sphere into a spherical hole in the solid, is approximately given by 2/3 µ/O (O°I - O)2 where a is the volume of spherical hole and no , is the volume of sphere. If we now consider the introduction of one mol of such spheres into an infinite volume of solid, then the relative partial molar free energy excess due to strain energy alone is GM ? = 2/3 µ/v (v ° 1 - v)2 where v is the molar volume of solvent and v°1, is the molar volume of pure solute type 1. Let us consider that these spheres are the two types of atoms in a binary solution, then there will be a similar relation for solute 2. The total relative integral molar free energy excess due to strain is then, to the approximations stated above GM ? = GM ? x1 + GM2 ? x2 = 2/3 µ/v [(v ° 1 - v)2 x1 + (v ° 1 - v)2 x2]. Lawson's relation for the strain energy can be de-

Jan 1, 1955

By W. H. Bassett

A 10-year, sea-water, corrosion test of tubes of several copper alloys has shown that many alloys withstood attack by solution, pitting, and dezinkification; a 1-year, salt-spray test of sheet-metal specimens of the same composition showed the same results. THE late J. P. Sparrow, chief operating engineer of the New York Edison Co., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in' September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40, 70-30, 80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period.

Jan 1, 1925

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By E. I. Larsen, E. F. Swazy, F. R. Hensel

High strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. Copper Powders The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this Paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975OC and repressing. The size of the finished compacts was 1/4, by % by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result fiequently in expansion during sintering for the type of powder used. Fig. 5 indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c, c., affect only slightly the pressure required to obtain a

Jan 1, 1946

By J. Philip Neal, Carroll P. Rogers

Feldspars, the most abundant minerals of the igneous rocks, occur in numerous forms and mixtures. The feldspars of commercial significance are found in widely distributed pegmatites as large crystals usually free of iron- bearing impurities and thus suitable for hand-cobbing, and also in larger bodies where the ore contains various types of feldspar inter- mingled with quartz and relatively free of iron- bearing impurities, or at least readily unlocked from impurities present at relatively coarse mesh. The latter type of ore includes some pegmatites, and the ''alaskite" bodies so common in the Spruce Pine district of North Carolina. On the west coast of the U.S. and in Oklahoma there is-r has been--commercial recovery of natural feldspathic sand as a source of alumina in glass and ceramics. "Aplite" in commercial terminology is a light-colored igneous rock with a granitic composition and a fine sugary texture, often banded with readily removable iron impurities. Two areas in Virginia produce aplite for the glass industry: one located in the vicinity of Piney River, Amherst County, and the other near Montpelier in Hanover County. According to Deer et al. (1966) the word feldspar derives from the Swedish feldt or falt (field) and "spath:" chunks of rock appearing in tilled ground overlying granite. Castle and Gillson (1960) indicate a Germanic origin, citing "spat," which is said to refer to any transparent or translucent material which is readily cleavable. The term "spar" has in the past been applied to minerals other than feld- spar, such as barite, calcite, and fluorite. It is correct to call the latter "fluorspar." There is a true barium feldspar, but it is rare and of no present economic importance. What is recognized as feldspar or "spar" by present producers and consumers consists of three silicate minerals which, if pure, would have the formu- las KAISi,O, (microcline or orthoclase), NaAlSi,O, (albite), and CaAl,Si,O, (anorthite). These are almost never found in pure form in nature, but occur together in great abundance in a three-component system. A considerable number of different combined ratios of these three exists, with the exception that isomorphism between potassium spar and calcium spar is very limited. User specifications for feldspar products are largely built around the prevalent naturally occurring ratios. Pas- sages following will refer to "K-spar," "Na- spar," or "Ca-spar." Nomenclature and Descriptive Terms Relating to both the mineralogy and the economics of feldspar are certain terms whose coverage it is useful to specify. Commercially, aplite is a feldspathic rock mined and beneficiated in two locations in Virginia, in which both titanium and feldspar minerals are present-the latter now being the major, if not the only, economic product. Technically, the term aplite when applied to this rock is of questionable accuracy. But, in light of accepted commercial usage, the term will be here used to designate it. Regarding the Virginia rock, Ross (1941) is cited.

Jan 1, 1975

By W. F. Domis, F. von Gemmingen, R. W. Whitmore, F. Garofalo

Constant-load creep-rupture tests at 1100°, 1300° and 1500°F were made on a Type-316, 18 Cr-8 Ni-ZMo, austenitic stainless steel to determine the relationship between ruptzire life and other aspects of creep behavior, The test program was designed on a statistical basis to check the variability of various creep properties and to determine emprically the dependence of minimutn creep rate and ruptzire life on initial stress, The dependence of the rupture life, tn, on the initial stress, a,, is found to be related to the stress dependence of the wrinimum creep rate, i,, and secondary creep strain, The instabilities or breaks found in the conventionual log - logt, plots can be traced to either a change in the linear dependence of log i, on log a, or to a change in secondary creep strain. In the alloy tested, rupture is found to be predowmanantly of the inter crystalline type, For this material, the secondary creep strain is -found to depend on the nature of the grain boundary precipitate, which affects grain boundary migration. It has been shown for a variety of metals and al tested at elevated temperatures under creep conditions that the empirical relationship exists between rupture life, tr, and minimum creep rate, i,. This relationship, in which C and a are in some cases independent of stress or temperature, shows in a general way that creep rupture depends on creep behavior prior to tertiary creep stage. To determine more fully the factors which control creep rupture requires, therefore, more knowledge of the relationship between rupture and creep behavior. To obtain such information, constant-load creep-rupture tests have been made on a Type-316, 18 Cr-8 Ni-2 Mo, austenitic stainless steel at 11000, 1300°, and 1500°F. These tests were designed on a statistical basis to determine the variability of the various creep properties measured and to determine empirically the stress dependence of minimum creep rate and rupture life. As a result of this work, various empirical relations have been established defining more closely the factor, C, in the relation between rupture life and minimum creep rate. This factor is found to be proportional to the amount of strain during secondary creep. The variation of secondary creep strain with rupture life and temperature is determined and its effect on rupture behavior discussed. The variability in minimum creep rate and rupture life is also dis- cussed and the dependence of these quantities on initial stress is interpreted. TEST MATERIAL AND TEST PROCEDURES The material tested is an austenitic stainless steel, AISI Type 316, of the following composition: C, 0.07 pct; Mn, 1.94 pct; P, 0.01 pct; S, 0.021 pct; Si, 0.38 pct; Cr, 18 pct; Ni, 11.4 pct; Mo, 2.15 pct; All 0.003 pct and N, 0.043 pct. The material was received as a hot-rolled 0.5-in. diam bar which was sectioned into 3.25 in. long blanks. Each blank was heat treated by holding 1/2 hr at 2000° F followed by water quenching. A 3/8-in. coupon was removed from each heat-treated blank and the microstructure was examined, the grain size determined, and the hardness measured. The microstructure was found to be uniform from blank to blank and the grain size was found to range from 4 to 6 ASTM numbers. Hardness, measured using a 20-kg load, varied between 127 and 148 Vpn. Tensile creep-rupture specimens having a 0.25 in. diam within a 1.5-in. reduced section were machined from the heat-treated blanks. Constant-load tests were made on these specimens at 1100°, 1300°, and 1500 F. Six specimens were tested at each stress level. Three creep-rupture machines were employed for tests at each temperature, two specimens being tested in each machine for each stress level. To minimize any effect due to local inhomogeneities along the length of the as-received bar the specimens were randomized before test. Each specimen was tested to rupture and in most cases an autographic extension-time curve was obtained. For very low stress levels at 1500°F no auto-

Jan 1, 1962

DAVID THOMAS 1871 R.W. RAYMOND 1872-1874 A.L. HOLLEY 1875 ABRAM S. HEWITT 1876 T. STERRY HUNT 1877 ECKLEY B. COXE 1878-1879 WILLIAM P. SHINN 1880 RICHARD P. ROTHWELL 1881

Jan 1, 1932

By P. W. Andrews, R. B. Toombs

ECONOMIC STRUCTURE OF MODERN INDUSTRIAL ECONOMIES The role of minerals in modern industrial economies may be examined in several ways. There are relationships with the various sectors of the economy: the primary, secondary, and tertiary industrial groupings and activities. Mineral supply and demand activities can be measured in terms of national accounts criteria. The economic policy objectives of the modem industrial economy are based to a considerable extent on the needs of the nation for economic supplies of miner- al materials. There is an important role for minerals relative to national security in peace and in wartime and many national policies are directed toward ensuring adequate sup- plies of minerals. Environmental control in the modem industrial economy is increasingly concerned with matters related directly to the production and use of minerals and these matters, in turn, bear importantly on conservation in mineral supply and demand. Mineral polices include specific provision for research and development activities concerned with the production and the use of minerals. In all, national policy objectives will be shaped in considerable part by the circum- stances of mineral supply and demand: the relative degree of availability from domestic and foreign sources, the state of the mineral-processing industries, and the degree of development of the mineral-using industries, and per capita and total changes in requirements. Goods made from mineral raw materials are the basis of all advanced societies and although this is taken for granted, every country is continually dealing with problems of mineral supply and demand. Considering that in the first 50 years of this century the consumption of mineral materials in a highly Industrialized country such as the United States increased by six times while the population was doubling, it becomes apparent that if a country is to enjoy rapid economic growth it must have access to huge and ever-growing supplies of mineral materials at lowest possible cost. Adequate supplies of mineral materials and wise usage of mineral resources have always been among the most important determents of a nation's survival The importance of access to adequate mineral supplies is increasing every year and this has significant international, as well as national, implications because of the unique locational characteristics of mineral resources. It is generally acknowledged that no particular type of natural resource is essential to a high level of national income or to economic progress. A country's endowment of natural resources need not exercise a determining influence on the course of its national income over time, provided it is able to trade. What is required for economic progress is the availability of a substantial quanti-

Jan 1, 1976

By S. Kobayashi, A. E. Armenákas, C. Mylonas

Earlier work1-4 has shown that commercial mild steels under static loading at the lowest natural operating temperatures fracture in a brittle manner only when damaged by a suitable history of straining. Notched and then compressed plates have fractured in subsequent tension at loads as low as 10 pct of the limit load and precompressed smooth bars at a subsequent extensional strain as low as 0.01. The comparison of the average net fracture stress with the flow limit stress was shown to be an excellent criterion of brittle or ductile behavior of mild steel structures when only loads and general stress levels are known. The present investigation shows that the deformation at fracture is a far more sensitive measure of brittleness than the fracture stress. Both criteria, deformation and stress, are used to determine the amount of uniform precompression of two mild steels, ABS-B and Project E-steel, resulting in brittle fracture under the strong constraint of a subsequently machined severe circumferential groove. The fracture stress equaled or exceeded the theoretical flow limit Ól = 2.680., ('based on the elevated yield stress at each prestrain) up to prestrains of about 0.20 and then fell off to about 1 at prestrains of 0.60. Yet a prestrain of only 0.05 reduced the elongation at the shoulders by a factor of about 4. The total plastic elongation of a region surrounding a sharp notch in prestrained steel deternines whether or not fracture will be initiated in large structures, hence is a direct and realistic measure of the remaining ductility and provides an excellent test of the material's resistance to embrittlement. ALMOST all engineering structures of mild steel which failed in service in a so-called "brittle" manner exhibited appreciable local plastic deformation (more than 1 pct) and a mixture of "cleavage" and "shear" fracture surfaces. Furthermore, the peak local stress in an advancing crack is always high. Such simple criteria as pure cleavage, absence of plasticity, or fracture stress, so useful in other fields, are insufficient to characterize brittleness in engineering structures at ordnary temperatures. The "brittle)' behavior of engineering structures is caused by the limited ductility at cracks or notch regions, as shown by recent work at Brown University summarized and extended in Refs. 1 to 4. It was also shown that the local ductility of mild steel may be catastrophically reduced by a suitable strain and temperature history similar to those which may occur in real structures. Localized yielding begins at the notch roots at low loads but is contained by surrounding elastic regions. The plastic strains are hence small. They increase slowly with the load up to the flow limit or limit load for an ideally plastic material. Unrestricted plastic flow then occurs. At such strains the real material locally st rain-hardens and fractures. With work-hardening materials no flow limit exists, and the transition from low to high plastic strains is gradual but increases more rapidly at loads close to the flow limit of an equivalent perfectly plastic material. When the available ductility is sufficient for reaching the limit load, the behavior is normal or "ductile". With insufficient ductility, fracture will occur at a low load and will be defined as "brittle". Accordingly the sufficiency or not of the ductility at a notch is reflected in the magnitude of the fracture load or average net stress as compared with the limit load or flow limit. The application of this criterion gave surprising results. Service failures under semistatic loading occurred mostly below the limit load, hence were "brittle". On the contrary all static tests with undamaged commercial mild steels reached the limit load in spite of the deepest notches and temperatures below Charpy impact transition (say about -30°F or higher). Notched bars showed no brittleness even under fully dynamic axial loading up to 1.5 x107 psi per sec at -23°F and about 2.5 x l06 psi per sec at -ll0°F, but broke in a brittle manner at -200°F and l03 psi per sec.' To propagate a fracture at low load, experimenters had to trigger it by superimposing a strong dynamic impact at a notch cooled by liquid nitrogen as in the Robertson5 or Esso tests.' Once started the cracks would run through warmer regions of smaller stress. Obviously the ductility of the apparently undamaged commercial steels was "sufficient" in the laboratory tests but not in the service fracture, where it must have been reduced by some embrittling procedure of fabrication or service. These conclusions were confirmed by the achievement of low static stress (brittle) fracture initiation in unwelded steel after a local reduction of ductility by simple prestraining. Symmetrically notched plates of undamaged mild steel cooled below the Charpy V-notch transition range were tested in central static tension: Undamaged plates withstood loads of limit intensity, but when subjected to prior in-plane com-pressive prestraining perpendicular to the notch axis and to accelerated aging, the plates fractured completely or partially at very low static loads, as low as one-tenth of the flow limit.2-4 However, damage could not be easily related to the strongly variable prestrain around a sharp notch. To obtain easier strain measurements, it was decided to use axially precom-pressed bars and bent bars. Final testing was done by

Jan 1, 1970

By E. S. Leaver

The authors of the paper above mentioned have sent the following statement to correct erroneous com-ments and implications in their article with the re-quest that it be published: "In the above mentioned article the reference to Bendelari jigs is used in the generic sense as applying to the mechanically driven diaphragm jigs. No attempt was made to dif-ferentiate between the various machines as installed on different dredges. The Natomas Company use a jig of their own manufacture. The Yuba Company installed the Placer jig as manufactured by the Pan American Engineer-ing Company. "The Pan American Engineering Company also manufactures the Crangle jig under their own name. This is a diaphragm jig in which the pulsations are produced by intermittent flow of water through the patent Crangle Valve and it has no driving mechanism."

Jan 1, 1937

By A. English, M. J. Greaves

This paper is a discussion of pelletizing systems developed over the last 15 to 20 years for the agglomeration of fine iron ore concentrates. Five different pelletizing systems are now in commercial use in the U.S., and for the purposes of comparison, estimated operating costs and capital costs for the construction of four of them are included. Capacities of existing commercial plants are examined, together with the anticipated capabilities of plants presently being built or projected. In just 21 years, the art of pelletizing iron ore concentrates has reached maturity with mastery of the separation of finely divided concentrates from low-grade iron ores and their agglomeration into pellets containing about 65% iron. This accomplishment has firmly established an improved feed for the blast furnace, with resulting benefits in faster reduction of burdens and greater economy of operation. The present production capacity of pelletizing facilities in the U.S. is about 20 million tons annually, and it is expected to double by 1970. The rapid expansion of pelletizing in the U. S. has been closely observed in European countries, notably in Sweden and Germany, where pioneer agglomerating techniques were developed early in this century. PELLETIZING PLANTS AND PROCESSES Twelve commercial pelletizing plants are presently in operation in the U. S. and Canada. An equal number are in various stages of engineering and construction, and many others are being considered. The pelletizing systems currently employed include shaft furnaces, horizontal grates using three different airflow arrangements, and grate kilns. The capacity of pelletizing operations in North America is shown in Table I. All of these plants are integrated with the mine, the ore-crushing facilities and the concentrating plant and are equipped with storage and loading-out facilities for the product. Normally, a pelletizing plant is composed of a shuttle conveyor above the receiving bins; balling equipment; a heat-hardening system including the necessary auxiliaries such as furnaces, burners and controls, ducts, fans, meters and instrumentation; fines recovery equipment; and product handling equipment. Also included are the necessary auxiliaries and utilities such as boilers or power plant; oil unloading and storage facilities; coal unloading storage, grinding and distribution facilities; and bentonite or other additive storage and distribution equipment. Shaft Furnaces: Vertical shaft furnaces used in this country are limited to the treatment of natural magnetite concentrates containing minor quantities of residual fluxing elements. Fig. 1 shows a perspective view of the shaft furnace with balling, feeding and pellet-handling equipment. An elevation of a shaft furnace is shown in Fig. 2. A commercial shaft furnace unit is about 45 ft in height with a 6 x 14-ft rectangular cross section and has a nominal production rate of approximately 50 gross tons of pellets per hour. The upper portion of the furnace shaft is constructed of fire brick as protection from the high process temperatures involved. The lower portion of the shaft is lined with abrasion-resistant brick to withstand erosion from the fired pellets. Rectangular-shaped, refractory-lined and insulated combustion chambers are situated on each side of the shaft furnace. Oil or gas is burned to produce high temperature gases which are forced into the furnace through ports located near the top of the combustion chambers. The shaft furnaces operate at a pressure of approximately 6 psi. Pellets are fed into the top of the furnace by a pantographic feeder designed to produce the desired pellet stockline. The furnace is kept filled at all times and pellets are fed and discharged from the furnace at the same rate. In early development, 10 to 12 lb of solid fuel was incorporated in the pellets. However, the main source of process heat is now derived from the combustion chamber gases. In some instances no solid fuel is used. The pellet movement in the shaft furnace is counter-current to the flow of gases. Ambient air is introduced through louvers at the lower end of the furnace, at about 6 psi, cooling the fired pellets and supplementing the heat of the high temperature gases from the combustion chamber ports. The zone of maximum temperature, located above the ports of the combus-

Jan 1, 1963

United Engineering Trustees, Inc. W. D. B. MOTTER, JR., '40 A. L. QUENEAU, '41 ALBERT ROBERTS, '39 The Engineering Foundation GEORGE D. BARRON, '40 F. F. COLCORD. '42 A. L. QUENEAU, '41

Jan 1, 1939

By Homer Griffield Turner

The nature and comparative features of anthracite and bituminous coals have been discussed by the writer in two previous papers.' Although this paper is offered as a further contribution to the subject, it seems desirable at the outset to repeat some of the descriptive matter of the early works in order to show the actual connection between various constituents of both coals and the new photomicrographs and other physical and chemical properties. Structure of Anthracite and Bituminous Coals A lump of bituminous coal (Fig. 1) is readily seen to be composed of layers differing from one another in texture, luster and thickness. There are, in general, three kinds of layers, although only two are usually seen. One is deep black, very compact, and has a bright luster; another is grayish black, has a duller luster and is less compact; the third is black, dull and porous in appearance, but because of its thinness is not often seen except on parting surfaces. This last material is charcoal. American students of coal morphology use the names anthraxylon, attritus, and fusain to designate these three constituents of laminated coal. Anthraxylon refers to the brightest bands, attritus to the duller layers, and fusain to the charcoal. Close examination of a lump of bituminous coal shows the brightest deep black layers to be embedded in the duller grayish black laminae. These deep black layers are lens-shaped and vary in thickness from thin sheets to over half an inch. They are often so continuous through the lump that their tapering terminae are not noticeable. On careful examination the duller grayish black laminae (Fig. 7) are seen to contain many very thin sheets of this very bright black material. The charcoal

Jan 1, 1930

By Wm. A. Haven

As soon as the likelihood of American participation in the war was established, and in spite of the fact that we can produce almost as much as all other countries combined, the demand for prompt deliveries of iron and steel products from American factories began to exceed their utmost capacity, and, after fifteen months of practically full operation, has continued to do so. Therefore, it would seem worth while to review some of the aspects of the supply and demand for steel as well as the efforts that are being made to bring them into balance. It is still being debated as to whether the situation should be defined as a real shortage that will persist through the emergency period or as a temporary one than can be relieved by less drastic measures than a Government-sponsored program of expanding existing plants and building new ones.

Jan 1, 1942

By C. Feng, I. R. Kramer

A study was conducted to determine the influence of the surface on the yield point of fcc metals and high-purity iron. For the high-purity fcc metals, the yield Point produced by restraining a specimen may be eliminated by removing a sufficient amount of the layer. A yield point similar to that in fcc metals was found when iron specimens were pre-strained after a prior deformation. This yield point is not due to an aging effect but is associated with the surface layer. The yield points in age-hardenable aluminum alloy and those connected with "work softening" are not affected by a surface-removal treatment and are, therefore, caused by bulk-type dislocation reactions. The yield point which appears in previously strained fcc metals has been the subject of numerous studies. Several theories have been advanced to explain this "unloading-reloading" yield point. Cottrell and stokes,' from their study on the effect of temperature on plastic properties of high-purity aluminum, considered that it was the result of an avalanche "breakdown" of Lomer-Cottrell sessile dislocations. Haasen and Kelly2 extended this concept of dislocation-dislocation interaction to account for the yield point when unloading and reloading was carried out at the same temperature. On the other hand, strain aging was found to be responsible for the yield point in A1-Mg alloy by Westwood and Broom,3 and in aluminum alloys containing various amounts of alloying elements by Smallman, Williamson, and Ardley.4 In these cases, the yield point is considered to be associated with the locking of dislocations by impurity atoms. Birn-baum and filer5,6 and Takamura and muira7 reported that, when a high-purity copper specimen was prestrained, then held at a lower stress, and finally reloaded at the prestrain temperature, a larger yield point was observed. Such an increase was attributed to the locking of dislocations by point defects. In addition, Bolling8 suggested that both mechanisms, i.e., dislocation-dislocation interaction and strain aging, are responsible for the yield phenomenon, at least in a brass. Thus, there appears to be experimental evidence for both the strain aging and dislocation-dislocation interaction theories to explain the yield point in the fcc metals and alloys. In a previous article,9 one of the authors observed that, if sufficient amounts of metal were electrolti-cally removed after deformation of a high-purity aluminum single crystal, the yield point did not appear upon reloading. Continued pursuit in this area revealed that the effect of the surface on the yield-point phenomenon is not limited to one metal but affects a variety of metals of different lattice structures. Nor is the effect limited to the yield points produced by simple unloading-reloading at constant temperature; the surface exerts an important role on the yield point even when the temperature is changed at some stage during the test. It is the intent of the present article to give additional information regarding the effect of the surface on the yield-point phenomenon and to show the association between the yield point in both fcc and bcc metals and the existence of a heavy concentration of dislocation in the region near the surface of a deformed specimen.10 EXPERIMENTAL Materials. The single crystals used in this study had a nominal cross section of 0.125 by 0.125 in. and a 3-in. gage length and were prepared by a modified Bridgman technique. The initial purity for the metals was 99.997, 99.999, and 99.999 pct for aluminum, copper, and gold, respectively. Bar stock of these same materials was used in the preparation of the polycrystalline specimens of aluminum and copper. The iron specimens were machined from rods of "ferrovac", reported to have a purity of 99.98 pct. In addition, a precipitation-hardening aluminum alloy, containing 1.5 pct Cu, 2.5 pct Mg, and 5.5 pct Zn, was used. The polycrystalline specimens of iron, copper, and the aluminum alloy had a diameter of 0.17 in. and a gage length of 2 in. while the high-purity aluminum specimen had a nominal rec-

Jan 1, 1965