Search Documents

By Michael Tenenbaum, C. C. Brown

IN recent years, the importance of slag control in basic open-hearth operations has been universally recognized. To effect such control during the working period of the heat, methods have been developed to measure or estimate slag oxidation and slag basicity. While satisfactory rapid chemical methods have been developed to determine slag oxidation, no completely adequate method of evaluating basicity has yet been provided. The most generally accepted control methods of measuring slag basicity are based on visual estimates. While considerable benefit may be derived from such estimates, the need for some measurable indication of slag basicity has become increasingly apparent. In a recent paper, Philbrook and Jolly[$] suggested a promising technique for making the basicity determination. Their method consists of measuring the pH of a mixture of powdered open-hearth slag and distilled water. It was found that a relation could be established between the slag basicity and the alkalinity of the water mixture as measured by the hydrogen-ion concentration. The general procedure followed in making the measurements and the considerations involved in constructing the original curves are given in the paper of Philbrook and jolly and need not be repeated. It is the purpose of this paper to discuss some of the factors considered in applying the pH measurements to actual slag control and to present some of the results of its application. FACTORS INVOLVED IN MEASURING pH OF WATER-SLAG MIXTURES To facilitate the application of the pH control system, it was desirable that no alteration be made in the routine methods of sampling and crushing the furnace slag. Some of the factors considered before establishing a curve to relate slag basicity with the pH reading are reviewed individually in the following paragraphs. EFFECT OF COOLING RATE Under actual operating conditions there can be considerable variation in the tem¬perature of the piece of slag crushed for the pH determination. To determine whether variations in crushing temperature or in cooling rate would affect the pH reading, a series of four samples was prepared from each of two separate slags. These samples represented conditions far more extreme than would actually be encountered. To obtain these samples, a thick pancake of slag was poured. One piece of this pancake was crushed immediately after it had solidified. Another piece was water-quenched and then crushed. A third piece was allowed to air-cool to room temperature before crushing. The fourth sample was prepared from a chilled slag. This sample was poured onto a heavy inclined steel plate at the

Jan 1, 1945

By Felix B. Shay

THE Agua Fria mine is in eastern Honduras at Lat. 140° 06' N., Long. 86° 36’ W. Danli, the seat of the local municipal government, is the nearest town. The property is approximately 44 miles east of Tegucigalpa, the terminus of a truck road from the Pacific coast. The mine lies at an altitude of 3300 ft. with surrounding elevations as high as 6000 feet. For 20 years the oxidized croppings of the Agua Fria vein had been worked intermittently when in 1927 an attempt was made to open the property. A shaft was sunk 300 ft. and considerable ore was blocked out, but before a mill could be installed financial difficulties arose and the mine reverted to the original owners. Erle P. Halliburton, of Los Angeles, purchased the property in 1934. At that time a careful consideration of all factors involved showed that air transport was the only practical method of moving the equipment and machinery necessary to commence production. The other alternative was by muleback, which required sectionalizing all equipment to a maximum load of 200 lb., and during the rainy season this type of freighting was subject to serious delays. It was decided to purchase a trimotor Ford powered by three Pratt and Whitney Wasp B motors developing 400 hp. each. There were several reasons for the choice: (1) this type of plane was available at a reasonable price, owing to its replacement by faster models on most of the airlines in the United States; (2) the ship was capable of carrying a pay load of 3000 lb. over the required distance; (3) since this airplane had been widely used there would be no difficulty in securing competent personnel or in purchasing spare parts. It was necessary to rebuild the plane for cargo service. The windows were removed and the fuselage was entirely covered. A hatch was cut in the top of the fuselage to receive heavy crane loads and pieces of freight that were too large or too long to go through the rear door. The seats were removed and the interior of the plane was lined with Duralumin sheets. A heavy-duty landing gear was installed and the floor was reinforced. The nearest site for an airport was two miles north of the mine. The necessary grading was done by a small track-type tractor with a wheeled grader, which was brought in overland. Six weeks was required for bring-

Jan 1, 1940

By J. J. Tietien, R. O. Clough

A technique previously used to prepare alloys of InAs1-xPx and GaAsl-x Px, miry: the gaseous hydrides arsine and phosphine, has been extended to grow single -crystalline GaAs 1-x Sb x by replacing the phos-phine with stibine. Procedures were developed for handling and storing stibine which now make this chemical useful for vapor phase growth. This represents the first time that this series of alloys has been grown from the vapor phase. Layers of P -type GaSb and GaSb-rich alloys have been grown with the carrier concentrations comparable to the lowest ever reported. In addition, a p-type alloy containing 4 pct GaSb exhibited a mobility of 400 sq cm per v-sec which is equivalent to the highest reported for GaAs. RECENTLY, interest has been shown in the preparation and properties of GaAs1-xSbx alloys, since it was predicted1 that for compositions in the range of 0.1 < x < 0.5, they might provide improved Gunn devices. However, preparation of these alloys presents fundamental difficulties. In the case of liquid phase growth, the large concentration difference between the liquidus and solidus in the phase diagram, at any given temperature, introduces constitutional supercooling problems. It is likely that, for this reason, virtually no description of the preparation of GaAs1-xSbx by this technique has been reported. In the case of vapor phase growth, problems are presented by the low vapor pressure of antimony, and the low melting point of GaSb and many of these alloys. In previous attempts1 at the vapor phase growth of these materials, using antimony pentachloride as the source of antimony vapor, alloy compositions were limited to those containing less than about 2 pct GaSb. This was in part due to the difficulty of avoiding condensation of antimony on introducing it to the growth zone. A growth technique has recently been described2 for the preparation of III-V compounds in which the hydrides of arsenic and phosphorous (AsH3 and pH3) are used as the source of the group V element. With this method, GaAs1-xPx and InAs1-xPx have been prepared2&apos;3 across both alloy series with very good electrical properties. Since the use of stibine (SbH3) affords the potential for effective introduction of antimony to the growth apparatus, in analogy with the other group V hydrides, this growth method has been explored for the preparation of GaAs1-xSbx alloys. In addition to GaSb, these alloys have now been prepared with values of x as high as 0.8. In the case of GaSb, undoped p-type layers were grown with carrier concentrations equivalent to the lowest reported in the literature. Thus it has been demonstrated that, with this growth technique, all of the alloys in this series can be prepared. EXPERIMENTAL PROCEDURE A) Growth Technique. The growth apparatus, shown schematically in Fig. 1, and procedure are virtually identical to that described2 for the growth of GaAs1-xPx alloys, with the exception that phosphine is replaced by stibine.* HCl is introduced over the gallium boat to *Purchased from Matheson Co., E. Rutherford,N+J. transport the gallium predominantly via its subchlo-ride to the reaction zone, where it reacts with arsenic and antimony on the substrate surface to form an alloy layer. The fundamental limiting factors to the growth of GaAs1-xSbx alloys from the vapor phase, especially GaSb-rich alloys, are the low melting point of GaSb (712°C) and the low vapor pressure of antimony at this temperature (<l mm). Thus, relatively low antimony pressures must be employed, which, however, imply low growth rates. To provide low antimony pressures, very dilute concentrations of arsine and stibine in a hydrogen carrier gas were used. Typical flow rates (referred to stp) were about 4 cm3 per min of HC1 (0.06 mole pct)+ from 0.1 to 1 cm3 per min of ASH, (0.002 to 0.02 mole pct), and from 1 to 10 cn13 per min of SbH3 (0.02 to 0.2 mole pct), with a total hydrogen carrier gas flow rate of about 6000 cm3 per min. Although no precise data on decomposition. kinetics exist, it is known4 that stibine decomposes extremely rapidly at elevated temperatures. However, the high linear velocities attendent with the high total flow rate (about 2000 cm per sec) delays cracking of the stibine until it reaches the reaction zone and prevents condensation of antimony in the system. To improve the growth rates of the GaSb-rich alloys, growth temperatures just below the alloy solidus are main-

Jan 1, 1970

By Emil-Paul Lorenz

Considered as a whole, the mineral resources of the Turkish Republic (Anatolia) are in their untapped virgin state, and the little development shown is not the result of modern systematic geologic exploration but the continuation of the ancient open-pit mining methods of the Orient. When I came to Turkey in 1924, I found myself confronted by a formidable task because of the lack of preliminary geologic mapping. Today this condition has not essentially changed; less than one per cent of the country is covered by topographic mapping adequate for modern requirements. However, I was able to bring a semblance of order in a presentation of the mineral deposits of this country, by tracing the story of the mineral deposits that showed surface evidence of their existence. At present only the easily discovered mineral deposits of coal, copper, and lead-silver ores are being exploited. In the case of coal, of 3,000,000,000 metric tons available, only 100,000,000 have been mined. The same is also true for copper, lead-silver, and other ores, as shown in Table 1.

Jan 1, 1948

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemi-sorption. FLOTATION of quartz is of practical importance as something to be avoided in soap-floating many types of ores. Clean, unactivated quartz is not floated with fatty acids and soaps, such as oleic acid and sodium oleate, in the quantities normally used for flotation. However, data in the literature indicate that almost any multivalent cation will activate quartz if given an opportunity. Thus, a common problem is to prevent activation of quartz by the various inorganic cations inevitably present in flotation pulps. Wark and his coworkers1 have demonstrated the reversibility of the chemical reactions and adsorptions involved in the activation, depression, and collection of the common sulphide minerals. The procedure in much of their work was to bring a mineral surface to equilibrium with solutions of known pH, collector concentration, and activator concentration, and then to test the floatability of the mineral by contact-angle measurement. From the data, graphs were constructed with pH and reagent concentrations as coordinates. These graphs show fields of flotation and fields of nonflotation, separated by narrow transition regions whose locations are shown by so-called contact curves. From the shapes and locations of the contact curves, which roughly separate fields of flotation from fields of nonflotation, a quantitative understanding of the interaction of the reagents with each other and with the minerals often can be deduced. The study of quartz flotation to be described in this paper follows in broad lines the approach of Wark and coworkers. That is, pH, activator concentration, and collector concentration were varied to find equilibrium conditions of flotation and non- flotation, and the results are presented graphically by means of contact curves. However, instead of testing for floatability by measuring the contact angle on a polished surface, a simple vacuum flotation technique was developed and used. Purified oleic acid was the collector and terpineol the frother. Barium activation was studied in some detail, and exploratory studies were made of activation with calcium, aluminum, ferric iron, and stannic tin. Preparation of Materials Quartz: Large lumps of high-grade vein quartz were crushed dry in a cone crusher and rolls. The —20, +28-mesh portion was screened out and used in the subsequent steps. This material was passed through a high-intensity magnetic separator to discard iron, then leached twice with hot concentrated HCl and washed repeatedly with distilled water. The cleaned sand was then wet ground with porcelain balls in a porcelain pebble mill, deslimed repeatedly by settling and decantation to discard —800-mesh material, and again washed with hot HCl followed by distilled water. The resulting stock of quartz was stored under water. Chemical analysis gave 99.8 pct SiO2. Table I gives the size analysis of the quartz used for flotation tests. Calculations from these data, using shape factors given by Gaudin and Hukki9 indicate a specific surface of about 500 cm2 per g. Blank flotation tests in distilled water, and in water with added frother, showed the prepared quartz to be completely nonfloatable and thus indicated the absence of organic contamination. Oleic Acid: The preparation of oleic acid was based on fractional vacuum distillation of methyl oleate2,3 followed by regeneration of oleic acid, and finally fractional crystallization of oleic acid from acetone solutions at low temperatures." The pure oleic acid was stored in a refrigerator. The iodine number of the oleic acid was found to be 90.0 (theoretical 89.93). Oleic acid was used in the form of a dilute water solution of sodium oleate, after preliminary flotation tests showed no effects of form of addition and order of addition of reagents when an adequate conditioning time (that is, 30 min) was provided. Other Reagents: Sodium hydroxide solutions low in carbonate were prepared by first making 1:1

Jan 1, 1951

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of quartz with oleic acid as collector and barium, calcium, aluminum, iron, and tin as activators were studied using a simple vacuum-flotation technique in glass-stoppered graduates. The detailed study of barium activation led to an interpretation based on ideal Langmuirian chemi-sorption. FLOTATION of quartz is of practical importance as something to be avoided in soap-floating many types of ores. Clean, unactivated quartz is not floated with fatty acids and soaps, such as oleic acid and sodium oleate, in the quantities normally used for flotation. However, data in the literature indicate that almost any multivalent cation will activate quartz if given an opportunity. Thus, a common problem is to prevent activation of quartz by the various inorganic cations inevitably present in flotation pulps. Wark and his coworkers1 have demonstrated the reversibility of the chemical reactions and adsorptions involved in the activation, depression, and collection of the common sulphide minerals. The procedure in much of their work was to bring a mineral surface to equilibrium with solutions of known pH, collector concentration, and activator concentration, and then to test the floatability of the mineral by contact-angle measurement. From the data, graphs were constructed with pH and reagent concentrations as coordinates. These graphs show fields of flotation and fields of nonflotation, separated by narrow transition regions whose locations are shown by so-called contact curves. From the shapes and locations of the contact curves, which roughly separate fields of flotation from fields of nonflotation, a quantitative understanding of the interaction of the reagents with each other and with the minerals often can be deduced. The study of quartz flotation to be described in this paper follows in broad lines the approach of Wark and coworkers. That is, pH, activator concentration, and collector concentration were varied to find equilibrium conditions of flotation and non- flotation, and the results are presented graphically by means of contact curves. However, instead of testing for floatability by measuring the contact angle on a polished surface, a simple vacuum flotation technique was developed and used. Purified oleic acid was the collector and terpineol the frother. Barium activation was studied in some detail, and exploratory studies were made of activation with calcium, aluminum, ferric iron, and stannic tin. Preparation of Materials Quartz: Large lumps of high-grade vein quartz were crushed dry in a cone crusher and rolls. The —20, +28-mesh portion was screened out and used in the subsequent steps. This material was passed through a high-intensity magnetic separator to discard iron, then leached twice with hot concentrated HCl and washed repeatedly with distilled water. The cleaned sand was then wet ground with porcelain balls in a porcelain pebble mill, deslimed repeatedly by settling and decantation to discard —800-mesh material, and again washed with hot HCl followed by distilled water. The resulting stock of quartz was stored under water. Chemical analysis gave 99.8 pct SiO2. Table I gives the size analysis of the quartz used for flotation tests. Calculations from these data, using shape factors given by Gaudin and Hukki9 indicate a specific surface of about 500 cm2 per g. Blank flotation tests in distilled water, and in water with added frother, showed the prepared quartz to be completely nonfloatable and thus indicated the absence of organic contamination. Oleic Acid: The preparation of oleic acid was based on fractional vacuum distillation of methyl oleate2,3 followed by regeneration of oleic acid, and finally fractional crystallization of oleic acid from acetone solutions at low temperatures." The pure oleic acid was stored in a refrigerator. The iodine number of the oleic acid was found to be 90.0 (theoretical 89.93). Oleic acid was used in the form of a dilute water solution of sodium oleate, after preliminary flotation tests showed no effects of form of addition and order of addition of reagents when an adequate conditioning time (that is, 30 min) was provided. Other Reagents: Sodium hydroxide solutions low in carbonate were prepared by first making 1:1

Jan 1, 1951

By R. N. Upadhyay, M. Maleki, I. Fatt

Conventional laboratory core analysis tests on samples of two limestone reservoir rocks indicate that about 20 per cent of PV is in dead-end pores. These tests (electric logging formation factor, mercury injection capillary pressure and miscible displacement) were carried out on 1/4-in. diameter test plugs. Test results show a clear dilference between these samples and sandstone or homogeneous limestone reservoir rock. Although the amount of dead-end pore space can be only roughly estimated, the presence of such pore space seems clearly indicated. Pressure transient studies also show presence of deadend PV. Although they do not give quantitative results, pressure transient data yield a reasonable estimate of the size of the neck connecting dead-end pores to the main flow channels. INTRODUCTION Equations conventionally used to describe reservoir flow behavior contain the implicit assumption that all connected pore spaces contributed to both porosity and permeability. Several authors3-7 have pointed out the changes in pressure transient behavior and in electric log interpretation that may result if this assumption is incorrect and, instead, dead-end or cul-de-sac pores are present. There is a need for laboratory tests that can detect presence of dead-end pores in core samples. With such information on hand the petroleum engineer can make more rational use of the mathematical tools now available for analysis of reservoir flow behavior. This paper describes laboratory studies designed to detect and, if possible, give a quantitative measure of dead-end PV in laboratory-size core plugs. Three reservoir rocks were used, two of which were limestones suspected of having deadend pore spaces and a well-known sandstone, used as a comparison standard, in which there is believed to be little or no dead-end pore space. All the studies were designed to measure the natural dead-end PV; i.e., the pore space which is dead-ended because of rock structure. During multiphase flow in a rock without dead-end pores, some parts of one of the phases can become surrounded by the other, thereby giving (for certain flow behavior) an effective dead-end pV8,9. Such behavior will not be described here.

Jan 1, 1967

By K. A. Natarajan, I. Iwasaki

The meaning and the utility of redox potential (Eh) measurements in sulfide flotation systems are examined. Since some preliminary plant Eh and laboratory flotation data were available, experiments were made to establish the pH range at which a platinum electrode might be used for such measurements without much difficulty in aerated systems. Triangular wave voltammetry was used to study the surface conditions of the electrode immersed in pyrrhotite suspensions at different pH. The measured Eh both at the plant and the laboratory is interpreted in terms of the experimental water-oxygen line.

Jan 1, 1974

By H. F. Yancey, M. R. Geer, C. L. Allyn, R. H. Eckhouse

W. M. Bertholf—This is an excellent report of a well-conducted investigation, of sufficient scope to provide generally useful information. Some years ago we had occasion to test the Humphreys spiral on the middling from our table plant. The conclusions reached in this investigation come as no surprise to us. In certain applications it is virtually impossible to improve on the spiral from the monetary returns point of view even though its "efficiency" may be low. We have noted that in all successful applications of the spiral the feed is "classified," hence we were somewhat disappointed in the showing the spiral made on the Poplar Ridge coal, the only one of the four which could really be considered the equivalent of a classified feed. As was noted in the paper, however, this coal contained a considerable amount of middle and high-gravity material, apparently more than enough to make up for the theoretical advantage of small particles in these categories. A comparison of particle size in the various specific gravity classes of the four coals is given in table XXV. Table XXV. Comparison of Particle Size in Various Specific Gravity Classes. (Unit size, 150 m to 0.105 mm) Black Eagle Clements Poplar Ridge Rosly,n 1.3 Float 7.47 10.60 8.68 9.66 1.3 x 1.4 7.89 7.96 7.58 8.20 1.4x1.6 7.24 8.36 5.58 6.85 1.6 x 1.8 7.98 8.31 3.42 7.33 Sink 1.8 7.85 7.13 5.09 7.41 Avg 7.69 10.08 7.15 8.38 This tabulation indicates that there was very little difference in the size of the various gravity fractions for three of the coals, Poplar Ridge varying the most. Examination of figs. 3, 6, 7, and 8 reveals a general similarity of behavior for all coals except Black Eagle. Would the authors care to speculate on the reasons for the difference in the distribution curve for the sink 1.60 material in the washed coal of fig. 3 as compared to the others? This difference is particularly noticeable in the 8xl4-mesh size. Was there a "shape effect"? J. D. Price and W. M. Bertholf—The performance data on three of the coals studied appear to be typical, but there are certain departures from the general pattern in the case of the Poplar Ridge coal which are large enough to deserve special consideration. For example: 1. Despite the high proportion of sink 1.60 material in the feed, it was not possible to make a corresponding proportion of high-ash reject. (See table XVI.) 2. Even though approximately 70 pct of the feed was 1.40 float with an ash content of 6.6 pct, and this

Jan 1, 1951

By R. H. Eckhouse, M. R. Geer, H. F. Yancey, C. L. Allyn

W. M. Bertholf—This is an excellent report of a well-conducted investigation, of sufficient scope to provide generally useful information. Some years ago we had occasion to test the Humphreys spiral on the middling from our table plant. The conclusions reached in this investigation come as no surprise to us. In certain applications it is virtually impossible to improve on the spiral from the monetary returns point of view even though its "efficiency" may be low. We have noted that in all successful applications of the spiral the feed is "classified," hence we were somewhat disappointed in the showing the spiral made on the Poplar Ridge coal, the only one of the four which could really be considered the equivalent of a classified feed. As was noted in the paper, however, this coal contained a considerable amount of middle and high-gravity material, apparently more than enough to make up for the theoretical advantage of small particles in these categories. A comparison of particle size in the various specific gravity classes of the four coals is given in table XXV. Table XXV. Comparison of Particle Size in Various Specific Gravity Classes. (Unit size, 150 m to 0.105 mm) Black Eagle Clements Poplar Ridge Rosly,n 1.3 Float 7.47 10.60 8.68 9.66 1.3 x 1.4 7.89 7.96 7.58 8.20 1.4x1.6 7.24 8.36 5.58 6.85 1.6 x 1.8 7.98 8.31 3.42 7.33 Sink 1.8 7.85 7.13 5.09 7.41 Avg 7.69 10.08 7.15 8.38 This tabulation indicates that there was very little difference in the size of the various gravity fractions for three of the coals, Poplar Ridge varying the most. Examination of figs. 3, 6, 7, and 8 reveals a general similarity of behavior for all coals except Black Eagle. Would the authors care to speculate on the reasons for the difference in the distribution curve for the sink 1.60 material in the washed coal of fig. 3 as compared to the others? This difference is particularly noticeable in the 8xl4-mesh size. Was there a "shape effect"? J. D. Price and W. M. Bertholf—The performance data on three of the coals studied appear to be typical, but there are certain departures from the general pattern in the case of the Poplar Ridge coal which are large enough to deserve special consideration. For example: 1. Despite the high proportion of sink 1.60 material in the feed, it was not possible to make a corresponding proportion of high-ash reject. (See table XVI.) 2. Even though approximately 70 pct of the feed was 1.40 float with an ash content of 6.6 pct, and this

Jan 1, 1951

By J. L. Sepulveda, R. F. Yap, R. Jauregui

INTRODUCTION The Third Theory of Comminution, oftentimes called the Bond Theory, was first published by Fred C. Bond in 1952. Since then, it has been widely used in the milling industry to size crushing and grinding equipment as well as to predict and evaluate their performance. Although two other comminution theories were advanced almost a century earlier, one by Rittinger, 1867, and the other by Kick, 1885, their use was limited because they did not agree with actual commercial comminution systems (Bond, 1961). According to Bond&apos;s Third Theory, the work input is proportional to the new crack tip length produced in particle breakage, and equals the work represented by the product minus that represented by the feed. For particles of similar shape, the crack tip length is equivalent to the square root of one-half the surface area, and the new crack length is proportional to [(1/vT - vF)]; where P and F are particles diameter of product and feed, respectively. For practical calculations, the particle diameter can be expressed in terms of the 80% passing sizes, P and F, respectively. Therefore, the work input is given by, [10 _ 10&apos;, W = Wi [7P_7F(1)] Where W = the energy input to the mill, (kwh/t) Wi = Work Index, (kwh/t) P = square sieve opening which 80% of the product passes, (microns) F = square sieve opening which 80% of the feed passes, (microns) Equation (1) is the mathematical statement of the Third Theory, or the Bond equation. Numerically, the work index is the energy required in kwh/t to reduce a given material from theoretically infinite feed size to 80% passing 100 microns. The work index of a particular material is determined in the laboratory by conducting the standard Bond grindability test. Bond developed separate tests for the rod mill and the ball mill. The simplified test method described in this paper, which is used at Anaconda Research Center to approximate the work index, is an alternative procedure to the ball mill

Jan 1, 1982

By J. C. Swartz

Measurements of the effect of precipitation stresses on the solubility of cementite (Fe3C) precipitates in a iron are reported. Solubilities were determined from measurements of the Snoek relaxation due to interstitial carbon after quenching from various equilibrium treatments. Stress-free precipitates were obtained by a spheroidizing treatment of vacuum-melted Fe 0.06 wt pet C. Subsequent equilibration treatments were designed to suppress nucleation of other precipitates. The results for stress-free cementite give a heat of solution of 14.8 i 0.2 keal per mole and an entropy change of 1.1 i 0.2 eu in the temperature range 400" to 715°C. Comparison with previous data indicates that the heat of solution increases about 6 keal per mole as temperature increases from 700" to 1000°C. Data on self-stressed cementite in quench-aged specimens of Fe 0.013 wt pet C indicate 1) an apparent heat of solution of 12.1 i 0.4 keal per mole in the range 280" to 690°C, 2) a strain energy of- 1.1 keal per mole Fe3C accompanying precipitation at 280°C, and 3&apos;) a gradual decrease in the strain energy of precipitation with increasing equilibration temperature. In com-parison with 2 and 3 the strain energy calculated for an isotropic model is 1.7 keal per mole Fe3C. The lower values obtained from the experiment indicated substantial stress velaxation by dislocation motion. WHEN a supersaturated solution of carbon in a iron is aged at temperatures in the range 200o to 700oC, the carbon clusters by interstitial diffusion and forms cementite (Fe3C) precipitate particles. Unstressed cementite has a volume per iron atom 9 pet higher than that of a iron;&apos; hence, cementite precipitate particles are usually under pressure from the iron matrix. The pressure would tend to increase the solubility of cementite in iron.&apos; This report describes anelastic measurements of the solubilities of self-stressed and stress-free cementite in a iron. Previous determinations of the cementite solubility are summarized in Table I. The method of cementite formation for each reference was studied to ascertain the state of stress of the cementite. The results judged to be for stress-free and stressed cementite are distinguished in the table. In the next section an estimate of the stress effect is obtained which is clearly too small to account for the large difference between the previous results in parts A and B of the table. THEORETICAL Let AGO be the standard free-energy change of the reaction Fe3C (eem.) = 3Fe (a) + C (in a) [1] in the absence of stresses. Since cementite precipitates appear to be rather pure10 and the carbon is so dilute in the iron,8 the cementite and iron of Eq. [ I] for the stress-free case have essentially unit activities and the activity of carbon equals its atom fraction xoC Then the stress-free equilibrium is expressed by RT In XoC = -?GO 121 To first approximation the change in the chemical potential of carbon due to the precipitation stresses equals the elastic strain energy W accompanying precipitation of a mole of cementite.2 Hence, in the presence of the precipitation stresses the equilibrium is described by RT In x sq = -?G° + W [3] where xsC is the mole fraction of dissolved carbon in the stressed case. An approximate value of W can be obtained from analysis of the inclusion problem in elasticity theory. The inclusion is a small portion of the matrix phase which has suffered a transformation while still imbedded in the matrix. In the absence of the constraint of the matrix the transformation would be equivalent to a uniform dilational strain eT. Both the matrix (a) phase and inclusion (0) phase are assumed to be homogeneous, isotropic materials. When the a and 0 phases have the same elastic moduli, which is approximately true for iron and cementite,11 the total strain energy per mole ß is12 2µVß(eT)2(3 +4 µx)-I [4]

Jan 1, 1968

The year 1934 saw a very thorough and intensive search for oil in Italy, both by the Government-subsidized company, the A.G.I.P., and by the few smaller operating companies. Approximately two-thirds of the exploration work, however, has been done in the Province of Emilia (northern Italy). The A.G.I.P. has been particularly active in the Emilia district and has sunk several rotary holes between Voghera and Ferrara on structures located by geophysical means in the Po Valley. Only insignificant amounts of oil have shown up in these tests to date but gas has been found in fair quantities, and apparently the company is not yet prepared to abandon its search in this part of the country without further effort. In Central Italy, the same company has put down four tests with cable tools and of these two were "dry holes" and the other two found only traces of oil. The A:G.I.P. also sank two wells in southern Italy and it is believed that in these the indications were sufficiently encouraging for the exploration work to be continued. No serious drilling has yet been done in Sicily by the A.G.I.P. or any other company. The annual subsidy granted to the A.G.I.P. by the Government for the duration of its five-year plan has been considerably reduced for 1935 and this may interfere with the completion of the coming year&apos;s program in all its details. The Società Petrolifera Italians, which is the chief producing company in the country, has continued the development of its two fields, Salsomaggiore and Vallezza, and at the same time has intensified its program of exploration. Rotary machinery has been introduced and is undergoing a thorough trial, and prospects of finding new pools at greater depths are considered good. The charcoal adsorption plant at Vallezza has operated satisfactorily throughout the year and has produced nearly 3000 bbl. of high-grade gasoline. Besides the exploration well at Rile dell&apos;Olio, which is still drilling, another wildcat test has been started at Torre-di-Traversetolo. All operations of this company are confined to the district of Emilia. The Società Petroli d&apos;Italia has continued to operate the old fields of Montechino, Gratera and Velleja, and has a well now exploring at greater depths in that general area. Of the two exploration wells in the Torino

Jan 1, 1935

By M. J. GAVEN

COMING over from the plant on the Denver and Rio Grande yesterday afternoon I was an interested listener to a smoking-room conversation that had to do with the experimental plant near Rifle. The people who were talking didn&apos;t know me and I didn&apos;t know them, but I learned quite a little. I understood that the plant would never operate; that it was not intended to operate; that the "oil trust" would keep it from operating; that our tramway had eaten up all our money and still was not working and would not work; that the plant was run by a bunch of kids, and that the superintendent was probably the biggest kid of the bunch. I plead guilty to the latter. But the people who were talking were misinformed. The plant is producing oil. The first sample of oil that came from our unit at the Bureau of Mines experimental plant at Rifle, Colo., was produced on Sept. 18, the first that came out of the condenser, and it is still coming. This sample of oil may mean to the United States what the first oil produced from the first well meant.

Jan 1, 1926

By Donald McLaughlin

INCREASING variety of interests among mining geologists is becoming more and more marked, as the frontier of their science and of its applications continues to expand. Each of the traditional lines of inquiry provides its crop of new and better defined problems, and answers to them are being found in far more precise terms than in the past as older uncertainties .are swept away with the sharper techniques and the even sharper ideas of modern geology. A glance over the assemblage of projects and publications in 1939 reveals conspicuous activity in many different parts of the front, such as the attack on the controversial question of the acid or alkaline character of ore-forming solutions, the place of mineral districts in the larger structural framework of continents, and the place of ore shoots in the local patterns of districts. Instructive comparisons are being made which cut across lines of older correlations or which reinforce them by pointing out heretofore ne-

Jan 1, 1940

By L. C. WYMAN

THIS paper discusses what mining reports should contain when presented to the California State Corporation Department, to accompany applications for the sale of stock to the general public, but the principles involved apply to mine financing everywhere. Such reports should &apos;be as clear and concise as possible, endeavoring to tell the truth in as few words as necessary. Should the engineer be aware that his report is to be used in connection with the sale of stock to the general public, he should consider the public as his client as well as the person who actually employs him. It is always required that the engineer be favorably known and of recognized standing. The following points should be given careful attention : 1. A legal description and location of the property. 2. Transportation conditions, and how they may be expected to affect the operating costs. 3. A brief history of the property, its production record as to tonnage, grade, and character of the ore should be given. Should the property have suspended operations for any reason, this should be given. Any details of former operating costs should be given, especially as to how any improvement could be made, due to better methods which might be employed.&apos; 4. The main geological features and whether they are such as to lead the engineer to believe that the mine may possibly &apos;be exhausted or the ore of such grade as to be no longer profitable. If he considers them favorable, he should give his reasons for the belief that further development work may produce profitable results. A map showing these features should be submitted, and it is not necessary that such map be highly colored or contain any more than the essential matters. 5. Other mines in the district, or those with similar

Jan 1, 1929

By James Terry Duce

The symposium on production for the year 1940 contains few papers on the foreign situation. It is probable that the foreign part of next year&apos;s symposium will be even shorter. This is due to rigid censorship in various countries, as the question of the volume of petroleum supplies has become one of great strategic importance. This is even more true than in the last war, owing to greater mechanization of armies. &apos;It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each space in Table I may represent one of four possibilities; either it is not applicable to the particular field, or the proper entry is not determinable, or the proper entry may be determinable but is not determinable from data available to the author, or the proper entry is determinable. When spaces are not applicable, leave blank; in spaces where the proper entries are determinable but not de-terminable frod data available to the author, please inserty; in spaces where the proper entries are determinable by the author, make such entries. y implies a hope that in some future year a definite figure will be available. The entry of a zero is a positive declaration, and an important declaration where it is in order. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In sucli cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces the correct entries represent the opinion of the author (for example, "Area Proved&apos;) and in such cases the entry need not be hedged to such extent as when the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when

Jan 1, 1941

Jan 1, 1906

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [bImpulse _P d At max =nwuwu where: bmax = maximum burden in m (ft). P= average detonation pressure in N/m2 (lb per ft2). A= duration of the average detonation pressure in sec. n= 3.1416. w= specific weight of rock in N/m3 (lb per ft3). u= minimum velocity that must be imparted to the rock in m/sec (ft per sec). d= borehole diameter in m (ft).] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m1/2-sec instead of meters. Adding the gravitational constant corrects this: [P d Atbmax =gu g = gravitational constant equal to 9.81 m/sect (32.2 ft per sec2).] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per see). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [(9 = 1.24)]. ? References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters&apos; Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 1, 1986

By F. H. Spedding

CONSIDERABLE confusion exists in the literature concerning the phase transformations exhibited by the lighter rare earth metals; namely, lanthanum,1-8 cerium,1,3,5,8,9-15 praseodymium,8 and neodymium.1,8,16,10 To obtain further information

Jan 1, 1958