Search Documents

By C. H. Lieb

ONE astounding fact in the production of petroleum is the comparatively recent realization by producers that flowing production is the cheapest crude produced. About 1910 or even later, operators actually endeavored to get a producing well to pumping as quickly as possible after completion. A well was not really considered to be completed until it was operating on the pump. Remarkable progress has been made since then. It was not until about 1920 that producers began to take a serious interest in pressures and to think a little about proper methods of handling oil wells. Pressure gauges were installed, and records of pressures maintained, which was quite an innovation. Desultory experiments were made with tubing of different sizes, as well as experiments with placing the bottom of the tubing string at different levels in the well. Probably the first important departure from customary procedure was about 1926, during the Seminole development, when gas lift

Jan 1, 1936

By P. Somasundaran, D. W. Fuerstenau

This article presents the results of an analysis of grinding of 1:1 mixtures of 4x8-mesh quartz and limestone in laboratory ball and rod mills. From these experiments, the amount of energy consumed in grinding each component of the mixture was determined. In the ball mill, limestone consumes slightly more energy than quartz in the initial stages of grinding, but as the grinding proceeds quartz begins to consume a slightly greater fraction of the energy. The postulate that the fraction of energy consumed by any material in a ball mill is proportional to its volume fraction has been shown to be approximately true. On the other hand, in a rod mill energy consumption by quartz and limestone is equal only in the initial stages of grinding, with energy consumption by quartz greatly exceeding that by limestone as rod milling proceeds. Preferential energy consumption in tumbling mills has been discussed in a number of papers. For example, from an analysis of the kinetics of comminu- tion in ball mills, Arbiter and Bhrany' obtained rate equations based on the postulate that only coarse particles are ground, indicating that fine particles are protected from the action of the balls by coarser particles. In rod mills this protective action is much more pronounced than in ball mills. Recent studies on the rod milling of limestone-quartz mixtures have shown that this protective action causes the mineral with the lowest grindability (quartz in this instance) to consume the greater fraction of energy. 2 However, in the ball milling of mixtures it has been postulated that the consumption of energy by one of the constituents is determined by its volume fraction within the mill. 3 Possibly this hypothesis may be a simplification of the ball milling of mixtures since the protective action suggested by Arbiter and Bhrany may result in some preferential energy consumption by one of the constituents of a mixture. The objective of this study has been to determine preferential energy consumption in laboratory ball and rod mills by analyzing size distributions of each material in the products obtained from grinding 1:l mixtures of quartz and limestone. MATERIALS AND METHOD The procedure for carrying out the tests on wet grinding quartz-limestone mixtures has already been described.'r3 In the present investigation, 1:l mix-

Jan 1, 1963

By T. Price, H. A. Holl, A. P. Greenough, A

UdIN, Shaler, and ulff' first used wires for the determination of the surface energy of a solid metal. A gage length was marked by tying knots in the wires, which were then suspended in a cylinder of the same metal, heated in an inert atmosphere for the appropriate time, cooled to room temperature, and finally removed from the furnace so that the lengths of the wires could be measured. With iron wires, difficulties associated with deformation during the phase changeszp3 made it necessary to measure the gage lengths at the tem-

Jan 1, 1964

By Paul E. Melancon, Vincent C. Kelley, Dale F. Kittel

Uranium of the Grants region occurs predominantly in continental sandstones of the upper part of the Jurassic Morrison Formation, but significant lesser deposits are found in limestone of the Jurassic Todilto Formation and in black shale of the Cretaceous Dakota Formation. The deposits are disseminations that form runs ranging from a few hundred tons to several million tons. The ore consists mainly of uraninite, uraniferous carbonaceous material, coffinite, and such secondary oxidized minerals at tyuyamunite, carnotite, and uranophane. In sandstone, the ore runs were locallized by mudstone, interstitial carbonaceous material, and primary sand channel trends. In limestone, ore deposition was related to folds and fracture zones. The great bulk of production has come from the Ambrosia Lake mines in the Grants district and the Jackpile and Paguate mines in the Laguna district. The ores, which generally have been 0.20 to 0.30 per cent U3O8, are treated at mills operated by Kerr-McGee Corporation, Homestake-Sapin Partners, and The Anaconda Company, all in the Grants district. In 14·years after discovery in 1950, the deposits had yielded concentrates valued in excess of $800,000,000. Since deposition of the Jurassic host rocks, a geologic history involving tilting, faulting, erosion, changing ground-water environments, and oxidation has considerably influenced the existence and character of the deposits. It is evident that their ongm is not simple. However, a degree of agreement appears probable for a pre-Dakota age for the original ore runs, and, at Ambrosia Lake, two principal stages of ore formation, separated by Laramide faulting, are recognized. All earlier ores have been modified by Quaternary oxidation, solution, and enrichment during which time much secondary tyuyamunite, metatyuyamunite, carnotite were formed.

Jan 1, 1968

By J. Hoover Mackin

The iron ore bodies of the Iron Springs district are replacement deposits of magnetite and hematite in Jurassic limestone around the borders of three intrusions of quartz-monzonite porphyry. Production in the period 1923-1965 was about 72,000,000 tons, nearly all of which was direct-shipping ore from open pits. The intrusions are laccolithic in form; all three were emplaced at the same stratigraphic horizon, which had been a zone of decollement gliding during the Laramide orogeny. The intrusions and associated volcanic rocks are post-orogenic. There was no change in the thickness of the limestone during the metallization. Comparison of the composition of the limestone and stratigraphically equivalent replacement ore indicates that, with every million tons of iron, there were additions of 40,000 tons of silicon, 20,000 tons of magnesium, and 10,000 tons of aluminum. The ore-forming fluid was derived from the exposed porphyry. The iron was first incorporated in hydroxyl-bearing mafics, which crystallized in depth and were carried upward in the magma that formed the hypabyssal intrusions. The mafic phenocrysts decayed deuterically in the new environment, releasing iron into the interstitial fluid of a consolidating crystal mush in the interior of the intrusions. Primary tension joints, which opened in areas of late intrusive distention, served as roots through which the ore-forming fluid was drawn from the crystal mush.

Jan 1, 1968

By J. J. Forbes

Probably the newest thing in mining safety, or safety for mines, is the apparent dissatisfaction on the part of the mineral industries, as represented by both management and labor, and the general public of the Nation, with the safety record of the mining industry. This is reflected by published comments and papers in the technical press;1-8 in labor periodicals, 10 11 in popular journals and periodicals,12 13 and in the daily press; also by discussions of the Safety Committees sponsored by the National Safety Council, 9, 14-15 the American Mining Congress, 1, 16 the American Institute of Mining and Metallurgical Engineers, 2, 4 the Mine Inspectors' Institute of America,6,8,17,18 the Coal Mining Institute of America, 5, 19, the American Standards Association, and others.20,21

Jan 1, 1949

By H. K. VAN POOLLEEN, W. Hurst, H. C. Bixel

In an earlier publication* I showed the development of the instantaneous point source solution for a well producing at a constant rate at the center of a system of two radial, adjoining sands of different permeabilities. I also showed how a wellbore radius could be incorporated if this were the development required. For the purpose of that paper and the point I wished to make, this solution served. It yielded a simplifying solution of sands in series identified by Eqs. VI-26 and VI-27. (These equations are reproduced in part by Bixel and van Poollen as their Eq. 3, Page 302.) I am well aware that the simplified solutions are approximations. The facts that these Ei-functions satisfy the diffusivity equation and meet the boundary conditions both at the well and at the interface between sands, and that the earliest time considerations yield zero pressure drop, are evidence that the solutions are good approximations. This was the purpose for these formulas, which I interpret that where the permeabilities are of finite order of magnitudes in the respective media, the relations give satisfactory answers. However, from the authors' point of view there are reservations, which leads me to consider their entire generalization as illustrated in their Figs. 1 through 14. What I understand from their storage capacity, relationship Fs, which is the ratio of the product of porosity and compressibility of Sand II to Sand I, that is employed here by the authors as a correlative means of identifying one figure from another, there is nothing in the exact mathematics that supports such a term as a means of correlation. This is taken out of context, unsustained that this applies. Here the mathematics are known, where the true correlation is the diffusivity term of one sand to another. This entails permeability that refers back again to the term M in their paper for the transmis-sibility of fluid from one sand to the other that should have also been a part of this storage capacity. In Figs. 8 through 14, which purported to show the simplified equation following this correlation, there are apparent discontinuities for M equal to or less than 0.1000 that differ from the trends for greater values of M. In this connection there is no reference radius given for this cumulative pressure drop in the paper that would permit me to make these calculations. However, what is clear for M equal to 0.1000 or less we are treated to almost a closed barrier at the interface; a condition entered by the writers without qualification. This across-the-board treatment of these simplified formulas, whatever the motive of the authors, enters into a range of permeabilities that even I as the contributor would have reservations that such could apply. Under comparable conditions I would be looking at a closed reservoir or some facsimile for such. The extent to which the approximation or the exact equations pertain is not evident in the generality offered by Bixel and van Poollen in their paper. Only when they or other writers show the comparison of the pressure distributions within the formations can one be able to judge the rational limits to subscribe to the simplified formulas.

Jan 1, 1969

By Lucien Eaton

THE use of filling in mines is less common in the United States than it is in Europe, where in some places it is required by law. In most cases the filling is placed by hand, and the material used for this purpose is the waste from development and that sorted from the ore in the stopes. When these sources provide an insufficient supply, additional rock must be quarried on surface or mined underground, or some other material :st be used. In different parts of the world sand, clay, gravel, culm, nulated slag, mill tailings, and even ashes, have been used as filling material in place of or in conjunction with rock. Of all the materials used for filling the best is probably clean sand. Gravel, finely crushed rock, granulated slag and coarse mill tailings are almost as good, and the methods used for placing and confining sand will apply equally well to any of these. The advantages of sand are its comparatively slight compressibility and the ease, economy and convenience with which it may be placed. On account of the voids, which necessarily occur in fills made of coarse waste, such fills will compress 10 to 25 per cent before they develop their full strength, whereas clean sand seldom compresses more than 5 per cent. Sand is especially desirable when practically complete filling is required, and sand derived from mill tailings, especially when not thoroughly cleaned, has been remarkably effective in sealing off and extinguishing mine fires. When natural sand is available on surface, or when it can be obtained from the mill tailings or tailings dump, the cost of using this material for fill will probably be considerably less than that of rock. In this paper it is not proposed to discuss all methods of filling, butt to describe some of the methods used for placing sand fill and to make a brief comparison of their merits.

Jan 1, 1932

By David R. Mitchell, Ernest M. Spokes

There is evidence that study of minerals now considered to have susceptibilities too low for magnetic separation should be continued. Present concepts may be false. INFORMATION on magnetic properties of minerals other than magnetite is scanty and sometimes erroneous. Often there is no information at all. W. R. Crane's table of tractive forces published in 1901 is still the best guide in the field, but Crane's data can be used as a guide only, since he ignored such important factors as impurities in the minerals, size, and packing effect. During the 1930's work by the U. S. Bureau of Mines added greatly to knowledge of the behavior of certain minerals in a magnetic field. The USBM bulletin gave for the first time complete magnetic characteristics for magnetite and fragmentary data for a few other minerals. The work reported here covers a study of the magnetic-susceptibility relationships of the wolframite series of minerals and sphalerites as related to their chemical compositions. Theories are proposed to explain divergences found from commonly accepted beliefs. Gouy Method for Determining Magnetic Susceptibility: The Gouy principle has been adequately described in the literature1-3 and applied in various ways.'- It may be summarized by stating that a body of material (gas, liquid, solid, or powder mixed with gas or liquid) of cylindrical shape changes in apparent weight if suspended with one end in a zone of higher magnetic field strength than is found in that portion of the field surrounding the other end of the cylinder. This may be expressed as K2 - K1 A (H2 - H2) - mg. [1] In determining the susceptibility of mineral specimens by the Gouy method, the mineral is reduced to a fine powder and packed in a glass weighing tube. Precise measurement of the bore and depth of the tube is made unnecessary by a calibration procedure. Using the basic expression of Eq. 1, Hoare"

Jan 1, 1959

By J. C. Bokros, A. S. Schwartz

The irradiation-induced densification of pyrolytic carbon has been shown to take place by a simple first-order rate process. The values of the densification constant, kd, for isotropic carbons are 1.0 x 10-22, 1.4 X 10-22 and 2.8 X 10-22 (nut)-1 at irradiation temperatures of 520o, 670°, and 1000oC, respectively. The apparent activation energy obtained from the temperature dependence of kd for isotropic carbons is about 0.2 ev. Estimates of the maximum stresses that develop in isotropic carbons owing to shrinkage onto an unyielding support show that stresses in excess of 15,000 psi may be avoided during irradiatian at 600" and 1000°C if the initial coating density is kept above 1.5 and 1.9 g per cu cw, respectively. If a carbon coating on an unyielding support is not completely isotropic, stresses may continue to build up at high neutron exposures after densification is complete because of continued anisotropic distortion. Stresses in excess of 15,000 psi from this source may be avoided during irradiation at 1000°C if' the Bacon anisotropy factor is kept below 1.3. A variety of applications of carbon and graphite in nuclear technology has stimulated numerous studies of the effect of neutron irradiation on these materials One of the most interesting problems associated with the use of carbons and graphites in the high fast neutron fluxes of nuclear reactors arises as a consequence of the neutron-induced dimensional changes that occur during irradiation. Energetic neutrons displace car- bon atoms from their lattice positions; and, depending on the temperature, the interstitials and vacancies produced migrate to form clusters, recombine, or are annihilated at dislocations or crystallite boundaries. The competition of various sinks for the point defects results in structure-sensitive bulk-dimensional changes that vary with temperature in a complicated way. This paper deals with the neutron-induced dimensional changes in turbostratic carbons that are being used as coatings on nuclear fuel particles. Details of the structure of these carbons and the variations of their structure with deposition conditions have been reported.'-3 It has been shown in previous work that the neutron-

Jan 1, 1968

By G. S. Hume

Production of petroleum and natural .gas increased in Canada in 1940 over the previous year. Alberta produced more than 97 per cent of the total Canadian production of 8,718,053 bbl. of oil, an increase for this province of nearly 12 per cent, whereas in Ontario and New Brunswick, where the production is relatively small, there was a slight decline. In Alberta the main producing field is Turner Valley, on the eastern edge of the foothills southwest of Calgary, and development continued in this field in 1940 with the completion of 36 wells, all of which obtained production. In the Red Coulce field, close to the International Boundary, near Coutts, no new wells were drilled and the seven producing wells showed a decline of 900 bbl. below the previous year. Also, in the Wainwright field of east central Alberta, four wells, yielding heavy crude oil, produced 4000 bbl. less oil than in 1939, owing possibly rather to discontinuous operation than to actual decline in potential yield. This decline was more than offset by production from a new field 40 miles northeast of Wainwright, at Borradaile, producing oil of 14" to I 5° A.P.1. There was a small increase in production during 1940 from the Del Bonita field, in southern Alberta, where the production is from two wells. The outstanding development of the year was the completion of Standard Oil Princess No. 2 well in the Steveville area, on the Plains 100 miles east of Calgary. This well was completed late in December with an initial flow1 of 520 bbl. of 26.3" A.P,I. oil, and 12,750 M cu. ft. of gas from the upper part of the Mississippian limestone. It has opened up a new field and given a further proof of the potentialities of the Southern Plains. The production of petroleum in Canada is shown in Table I. Since most of the yield comes from Alberta, the production is shown from the various fields in Table 2. The sale value of the petroleum produced in Canada in 1940 exceeded 11.1 million dollars, which is still somewhat less than the value of the natural gas production, shown in Table 3. Table i.—Production of Petroleum in Canada" Barrels Province 1939 1940 New Brunswick........ 20,101 21,161 Ontario............... 206,196 186,471 Alberta............... 7,595,000 8,493,237 Northwest Territories. . 17,013 8,493,23717.184 Total............... 7,838,310 8,718,053 Value............... $10,353,351 $11.113,000 0 Bureau of Statistics, Ottawa. Turner Valley, Alberta Turner Valley continues to be by far the largest producing field in Canada (details are given in Table 4), The limits of the Pr in- field are now Known. On the east the oil area is bounded by the gas cap, which in turn is cut off on its east side by a major overthrust fault; on the west, ii is defined by edge water at a level of 4roc

Jan 1, 1941

By G. S. Hume

Production of petroleum and natural .gas increased in Canada in 1940 over the previous year. Alberta produced more than 97 per cent of the total Canadian production of 8,718,053 bbl. of oil, an increase for this province of nearly 12 per cent, whereas in Ontario and New Brunswick, where the production is relatively small, there was a slight decline. In Alberta the main producing field is Turner Valley, on the eastern edge of the foothills southwest of Calgary, and development continued in this field in 1940 with the completion of 36 wells, all of which obtained production. In the Red Coulce field, close to the International Boundary, near Coutts, no new wells were drilled and the seven producing wells showed a decline of 900 bbl. below the previous year. Also, in the Wainwright field of east central Alberta, four wells, yielding heavy crude oil, produced 4000 bbl. less oil than in 1939, owing possibly rather to discontinuous operation than to actual decline in potential yield. This decline was more than offset by production from a new field 40 miles northeast of Wainwright, at Borradaile, producing oil of 14" to I 5° A.P.1. There was a small increase in production during 1940 from the Del Bonita field, in southern Alberta, where the production is from two wells. The outstanding development of the year was the completion of Standard Oil Princess No. 2 well in the Steveville area, on the Plains 100 miles east of Calgary. This well was completed late in December with an initial flow1 of 520 bbl. of 26.3" A.P,I. oil, and 12,750 M cu. ft. of gas from the upper part of the Mississippian limestone. It has opened up a new field and given a further proof of the potentialities of the Southern Plains. The production of petroleum in Canada is shown in Table I. Since most of the yield comes from Alberta, the production is shown from the various fields in Table 2. The sale value of the petroleum produced in Canada in 1940 exceeded 11.1 million dollars, which is still somewhat less than the value of the natural gas production, shown in Table 3. Table i.—Production of Petroleum in Canada" Barrels Province 1939 1940 New Brunswick........ 20,101 21,161 Ontario............... 206,196 186,471 Alberta............... 7,595,000 8,493,237 Northwest Territories. . 17,013 8,493,23717.184 Total............... 7,838,310 8,718,053 Value............... $10,353,351 $11.113,000 0 Bureau of Statistics, Ottawa. Turner Valley, Alberta Turner Valley continues to be by far the largest producing field in Canada (details are given in Table 4), The limits of the Pr in- field are now Known. On the east the oil area is bounded by the gas cap, which in turn is cut off on its east side by a major overthrust fault; on the west, ii is defined by edge water at a level of 4roc

Jan 1, 1941

By J. E. House, J. L. Drobnick, R. R. Swanson, D. W. Agers

The paper describes an improved process for the recovery, purification, and concentration of copper values from acidic dump leach liquors. The process employs a new liquid ion exchange material (LIX® 64 reagent) capable of separating copper values from iron and other impurities common to dump leach liquors in the typical pH range of 1.4-3.0. Properties and performance of the reagent are discussed. Design scale-up information for both pilot plants and commercial installations, including preliminary economics, are presented. Economic considerations include the production of electrolytic copper from the purified copper aqueous concentrate. INTRODUCTION Since the commercial acceptance of the liquid ion exchange process in the mineral processing industry, it has been predicted that a wide selection of chemical reagents to efficiently and economically separate many metals in solution under a wide range of conditions would be commercially available. Several years ago, General Mills began a basic research and development program to determine if it were possible to develop a reagent to extract economically metallic ion from existing process streams. Progress toward reaching this objective was reported in late 1963, when development of quantities of LIX -63 reagent, a highly selective reagent for the extraction of copper, was introduced. The properties of this reagent are described in a previous paper.' The development work with this reagent indicated that perhaps the largest potential application for a copper extractant, the treatment of acidic dump leach liquors, would not be economically possible with LIX-63 because of limitations of the reagent to extract copper below a pH of 3.0. The relatively small pH adjustment required with LIX-63 would result in a significant processing cost and the undesirable precipitation of ferric hydroxide from the liquor. This pointed to the need for another copper extractant which would extract copper from dump leach liquors without pH adjustment. General Mills was successful in synthesizing a molecule which does not have the pH limitation of the LIX-63, yet possesses the selectivity-solubility properties required of a metallic extractant. The resulting LIX-64 reagent broadens the pH range from which copper can be effectively extracted and separated from other metallic impurities. Of special significance is the fact that the reagent, LIX-64 was developed by combining the technical requirements of a specific problem in hydro-metallurgy with theoretical organic and physical chemical principles.

Jan 1, 1967

By MAURICE ALTMAYER

M Y DUTIES, as a member of the Department of Franco-American War Cooperation of the French High Commission were to study the copper and brass industries of America from the mining of the various non-ferrous metals to the semi-finished, or finished materials. In the pursuit of these studies, it was my privilege to visit a number of industries and organizations in different parts of the country. I first visited most of the Eastern copper refineries that were supplying the Allies with vast amounts of metal. These works are producing their material by the multiple or the series process, although the first method predominates. But, regardless of the process employed all the plants attain an exceptionally high standard of quality in their production. One of the points that particularly attracted attention was the manner in which improvements could be traced from the older worlds to the more recent ones. The impression was that, thanks to a spirit of broad-minded cooperation between the principals of the companies and frequent exchanges of views between members of the staffs, all persons interested benefitted by the experience thus gained, to the advantage of the community at large.

Jan 1, 1920

By Moore, Richard B

PROBABLY no other metal excites as much interest, among both scientific men and the general public, as radium. This is due partly to the high cost of radium salts and partly to the peculiar properties of the element. Since radium-bearing ores were discovered in the United States, the interest of American scientific men has been stimulated and, at the present time, more radium is extracted and refined in this country than in all the rest of the world together. HISTORY The property of radioactivity was discovered, partly by accident, by Henri Becquerel, the French physicist, in 1896. He was experimenting with certain fluorescent substances in order to find, if possible, a connection between fluorescence and the recently discovered Y-rays. Among other chemicals which possess the property of fluorescence, he was using

Jan 8, 1918

By D. H. Gurinsky, D. G. Schweitzer

The empirical equilibrium constantsd the heat of reaction for the reduction have been determined from 300° to 500°C. The mechanisms of the oxidation of uranium and magnesium from dilute bismuth solutions have been investigated. The kinetics of some of the reactions were affected by air adsorbed on the uranium oxides. THE Liquid Metal Fuel Reactor studied at Brook-haven National Laboratory uses a solution of uranium in bismuth as the fuel. Corrosion and stability problems require that the fuel solution contain corrosion inhibitors and deoxidants. Of the additives tested, magnesium has been found to be the best deoxidant and zirconium the best corrosion inhibitor in bismuth. Some experiments1 indicate that magnesium may play a secondary role in increasing the effectiveness of zirconium in inhibiting corrosion. The work reported here was intended to determine the relative concentrations of Mg and U required to prevent oxidation of the uranium fuel in the event of an air leak. In addition, an attempt was made to identify some of the mechanisms of the oxidation and reduction reactions occurring in the liquid bismuth solutions. EXPERIMENTAL Apparatus and Procedure—The equipment shown in Fig. 1 was designed so that the reaction kinetics could be studied as functions of temperature, melt composition, pressure, and flow rate. At the start of a run, the 10-liter bell jar (F) is removed by opening the bottom Dresser fitting (L), and the bismuth and additives are placed in a pyrex crystallizing dish (I). The bell jar is replaced, the system is evacuated to 10-5 to 10-6 mm Hg and then the heater (J) is turned on. When the selected temperature is reached, the oxidizing gas is admitted to the system to the desired pressure as read on the manometer (D). Gas is introduced through the slide tube (Q) which has a pyrex frit (R) sealed to its bottom. Stirring is accomplished by immersing the end of the tube in the melt. To maintain a constant pressure under flow the input and evacuation rates must be equalized. To obtain this condition stopcock (C) is closed and flowmeters (B) are matched. The reaction is "stopped" by closing the inlet flowmeter and quickly evacuating the system. To obtain a liquid metal sample, the system is evacuated with the sampler positioned near the surface of the liquid. The sampler, Fig. 2, is then immersed until its thermocouple reading matches thermocouple (G) Fig. 1. The system is then pressurized with helium which forces the solution through the frit. Twenty to 30 min elapsed between the time the system was evacuated and sampled. During evacuation and pressurization of the system, the temperature variations did not exceed ± 5°C. While bubbling occurred the temperature remained constant to within 1/2 oC. The volume of the equipment was determined by adding a known volume of air at atmospheric pressure to the evacuated system and noting the resulting pressure.

Jan 1, 1962

By Y. Oka, H. Majima

When a rock particle is subjected to an external force, internal stresses and deformations are experienced by the particle. Assuming that the breakage of a rock is mainly due to tensile stresses generated by the action of a pair of concentrated loads, F, directed in compression towards the loading points at the shortest distance, as illustrated in Fig. 1, the stress and deformation experienced by a particle of irregular shape can be determined with the aid of the theory of elasticity. According to the photoelastic experiments made by one of the present authors,' the stress states in a rock particle of irregular shape are quite similar to that of an inscribed sphere of diameter x, as indicated in Fig. 1, but accompanied by the faint stresses, in the vicinity of the particle outside of the inscribed sphere. Therefore, the stress components in an irregularly shaped particle can be estimated by referring to stress components in a sphere. Applying polar spherical coordinates to an elastic spherical body, as shown in Fig. 1, the stress components are all expressed as multiples of F /x2 and more or less influenced by the loading angle and Poisson's number m. In general, the energy w, acting on a rock particle is defined as the product of loading compression F

Jan 1, 1970

By Henry Rawdon

THE following note describing the behavior of copper under rather unusual conditions is offered here for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning it, as well as for softening it. It is well known that metals may be rendered very brittle by electrolytic action, in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear a similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. To demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 819° C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for

Jan 2, 1920

Jan 1, 1970

CAPTAIN JOHN H. BALLAMY John H. Ballamy, Captain on the Regimental Staff of the 103d Engineers, was killed near Fismes, on August 9, 1918. Captain Ballamy was born at Plymouth, Pa., in 1886 and graduated from the High School of that town in 1903. In the following year he began work as a coal miner, and at the same time began the study of mining engineering in the evening and any other spare time. He continued this diligent and energetic practice for many years. For sixteen years he continued in the employment of the Delaware, Lackawanna & Western Railroad Company's coal mining department, first as a practical miner, next as rodman on the survey corps, of which he soon became chief, then draftsman and mining engineer in the company's office. In January, 1916, he was promoted to the position of district engineer in charge of mining engineering work. He became a member of this Institute in September, 1917. CAPTAIN JOHN H BALLAMY. Captain Ballamy's military experience began at the same time as his engineering practice. He was a charter member of Company A, Engineers, N. G. P., which was organized ten years ago. He saw service on the Mexican border as First Lieutenant of this Company, and remained in that position until November, 1916. In July, 1917, he was again called into service and was sent to Camp Hancock, Ga., with the 103d Regiment of Engineers. Before joining this regiment he attended a school for officers at Fort Sill, Okla., where he received special training in field fortifications. In December, 1917, he was commissioned Topographical Captain on the Regimental Staff, and in April, 1918, preceded his regiment by about six weeks to France, where he again attended an officers' training school. He rejoined his regiment on July 15, near Chateau Thierry and was killed near Fismes on August 9, 1918.

Jan 11, 1918