Search Documents

By Albert Sauveur

THE following experiments were conducted in order to study the influence of the rate of cooling through and below solidification on the dendritic structure (macrostructure) and microstructure of some hypoeutectoid steel. The steel selected was of commercial grade and had the following composition: C, 0.40 per cent.; Mn, 0.85; Si, 0.70; P, 0.099; S, 0.043. After melting in vacuum in an Arsem furnace, the various samples were allowed to solidify and to cool to room temperature as indicated in Fig. 1. Samples were thus obtained representing all possible combinations of slow and fast cooling through the various ranges of temperatures indicated, namely: (1), zone of solidification or primary crystallization, (2) zone of granulation, and (3) zone of secondary crystallization. The location of the different temperature zones in the iron-carbon equilibrium diagram is shown in Fig. 2. The authors adopted. Belaiew's notations. The designations of the various samples readily indicate their treatment, as will be apparent from Table 1.

Jan 1, 1930

By Thomas V. Falkie, Robert Stefanko

Previous articles in this column have defined the manpower situation as it. applies to the coal industry. There is at present a shortage of experienced managers, mining engineers, technicians and skilled workers. The extent of this shortage is controversial, but it is sufficiently important to have received the serious attention of coal industry people at all levels. It has also been discussed by union officials, educators, government agencies and trade publications as well as other communications media. Discussion is not enough, however. A plan of action is needed. Some suggestions for such a plan are presented here. First, the coal industry must interest itself in government training programs. The U.S. Government (primarily the Bureau of Mines and HEW) is planning to spend or is spending millions of dollars to educate and train technicians, inspectors, engineers and miners. The new Federal Health and Safety Academy at Beckley, W. Va., for example, will involve an expenditure of $20-30 million for the physical plant alone. There are encouraging signs that the present hierarchy in the Bureau of Mines intends to seek the advice of mining educators on some of these projects, but industry should also demand a voice in the policy to be followed in making these expenditures.

Jan 1, 1971

On Friday, Jan. 17, the thirteenth impression of the Perkin Medal was presented to Dr. Frederick Gardner Cottrell, at a meeting of the New York Section of the Society of Chemical Industry, held at the Chemists' Club, in New York City. The presentation address was delivered by Dr. C. F. Chandler, Senior Past President of the Society. The medal was awarded for the recipient's work in the electrical precipitation of suspended particles in gases. Dr. Cottrell's career, which is so familiar to members of the Institute, was sketched by Dr. Chandler. He told at some length of the experiments leading up to the final solution of electrostatic precipitation, which has done so much to solve the problem of smelter smoke. The principal interest in Dr. Cottrell's speech of acceptance lay in his remarks about helium, the production of which has been so reduced in cost that it has practically supplanted the use of hydrogen for inflation purposes in war balloons. He said: "Two or three weeks after war was declared in 1917, Dr. R. B. Moore attended a meeting of the American Chemical Society in Kansas City. At the general session, Mr. Seibel of the University of Kansas, gave a paper on krypton and xenon in some of the natural gases of Kansas. At the end of his paper, he expressed regret that at such a time, when everyone was thinking of war problems, his paper was of a purely scientific nature and had no practical bearing on the war. Dr. Moore immediately got up and said that he did not agree with Mr. Seibel. The presence of helium in those wells could, and should, have a very practical bearing on the war, as this gas could be extracted in quantity from the natural gas and used for balloons and Zeppelins. He pointed out some of the natural advantages of helium over hydrogen, and quoted Sir William Ramsey's letter advocating the use of helium for airships. The general attitude of those present was one of scepticism, so he finally asked Dr. Cady for his opinion who stated that he believed-the thing could be done, but was very doubtful whether it could ever be made practical on account of the cost." Dr. Moore in a letter wrote: "That same day I talked to Dr. Parsons, who was present at the meeting and was returning to Washington almost immediately. I told him what had happened, and that I believed the matter should be taken up by the Bureau at once and presented to the War Department. He promised to do this as soon as he got to Washington; and I know that he did take the matter up with other Bureau officials." Dr. Cottrell continued in part: News of Ramsey's suggestions also reached this .country through other channels and eventually came to our attention. Professors Satterly and Patterson of the University of Toronto commenced experimentation of the subject Jan. 1, 1916. Col. G. A. Burrell, who headed the research department of the Gas Warfare Service at the American University, tells me that Cady's experiments had also suggested similar possibilities to him.

Jan 3, 1919

By D. C. Jackling

I BESPEAK your indulgence for a brief expression of the views of a patriarch in the field of mineral industry technology relative to young men's problems in that sphere of education and endeavor. Wherever hereafter I employ the terms "technical education," "engineer," "technologist," or similar expressions, these are intended to be understood as relating to the broad field of the sciences and arts applicable to the mineral industries. First, the usefulness of technical education to either the possessor of it or those to whom its services may be made available industrially depends primarily upon the quality of the education and the capabilities of the educated to put his talents to effective and constructive employment in his chosen field of applied science.

Jan 1, 1940

By Sherwin F. Kelly

PLAIN mining engineers usually avoid any gathering of geo¬physicists because of the incomprehensibility of their discussion to the uninitiated. This being so, gradients, gravity and gammas will be deferred to the end of this review, the first part of which will be devoted to what has been done in applying geophysics to the solution of real field problems. From the West, J. J. Jakosky reports that International Geophysics has had its activities fairly well 'divided between mining (both placer and lode), oil structural work, and clans-site and reservoir investigations. In oil exploration, electrical methods are used for depths down to 2500 ft., beyond which they utilize seismic methods. They find in their placer work that the many 'magnetic anomalies encountered in the bedrock of the Southwest render the electrical techniques more satisfactory, and with them they are obtaining thickness and tonnage of gravels, depth to and contour of the underlying bedrock as well as important structural features therein, and water-table elevations.

Jan 1, 1934

By Cloyd M. Smith

B. F. TiLLson*— The manifold difficulties of accurate anemometry in irregular sections of mine passageways, the irregular distributions of velocities in cross sections of the same, and the disturbing influence of the observer upon the air flow, all indicate an undesirable inaccuracy of results obtainable by any standardized method of traversing the section by an anemometer. It seems obvious that another, and simpler, method should be used to determine the volume of air flow in mine passages, namely: 1. At appropriate locations cement or calked framework rings should be installed permanently to equalize the irregularities of sectional contour and provide a place and means of attachment for a temporary cloth brattice which bears a rigid orifice. 2. The measurement of the velocity of air flow through the orifice may then be by anemometer or, preferably, by Pitot tube measurements of the differential pressures on both sides of the orifice in accordance with the standard practices available in engineering 1iterature. † The constants may be determined for various measuring positions in relation to the resulting "vena contracta." 3. The position of the person who makes the measurements is behind the brattice out of the air stream. The Pitot tube does not offer as disturbing an obstruction as the anemometer. A recording gauge may be employed to integrate fluctuations in air flow through that portion of the mine. No traverses are required because the reading may be at a single central point. An anemometer can be used with an orifice flow. The orifice will increase the air velocity at the measuring point, with correspondingly more accurate measurements where the normal air velocity through the passageway is low. Portable brattices might be devised with the cushioning rims which would seal against irregular rock surfaces where permanent rings were not available or feasible. The development by the Ventilation Committee of standard procedures and devices for the orifice measurement of the flow of mine ventilating air might be a desirable project for this coming year. C. M. Smith (author's reply)—Thank you for your discussion of my paper on underground anemometry. Your suggested method of measuring underground air flow is a novel one which might be applicable in some situations. It should be tested along with other suggested methods in any investigation of this subject. G. E. McElroy*—In spite of the adverse publicity that vane-anemometer methods of air measurement have had in the past and that contributed by the present paper, I endorse Mr. Erickovic's statement that anemometer traversing "has proved to be widely applicable, expeditious and simple" and add that available methods are accurate enough for the purposes for which they may be used. The fact that the great majority of minor mine officials assess relative changes in rates of air flow by comparison of crude vane-anemometer measurements, known to average 20 to 30 pct high, has no important bearing on this subject, because state inspection standards were based originally on such methods of air measurement. Federal inspection standards are based on actual rates of flow as determined by traversing, and interest in traversing methods is rapidly increasing. In considering traversing methods, three aspects are of major importance: (1) the absolute accuracy of calibrations; (2) the degree of interference with normal flow conditions introduced by traversing methods designed for accurate measurement by shaft-mounted instruments; and (3) the proper "method" factor to use for approximate measurements by hand-held instruments. With respect to absolute accuracy of calibrations, we have always placed reliance on calibrations made by the National Bureau of Standards, with which manufacturers' calibrations have usually agreed very closely. It is therefore particularly disturbing to find7 that calibrations made previous to June 1947 are presumably about 5 pct in error because of excessive registry caused by the thin flat plates on which anemometers were mounted for calibration. Velocities corrected for calibration have therefore averaged about 5 pct low in all probability. In this connection, it is interesting to note that an anemometer calibrated against Pitot-tube measurement by a single-point method in the Bureau of Mines experimental coal nine in 1923 indicated this same difference of about 5 pct and that the same instrument calibrated by a traversing method in a metal mine some months later indicated a difference in the same direction of about 4 pct. These results are reported by the Bureau of Mines.8 Regarding the degree of interference, or changes in velocity distribution, caused by the position of the observer's body in traversing operations, misconceptions seem to be especially prevalent, resulting in increasing advocacy of methods, such as the "clear section" method outlined in this paper, that cause just the type of interferences that they are designed to avoid. The degree of interference for any method may be gauged easily by a few experiments with a velocity-pressure gauge connected to a Pitot tube or with an indicating velocity meter such as the Velometer. In an experiment cited by McElroy and Richardson,# a decrease of 5 pct was noted at ten widths upstream from a 6-in. plank, whereas an observer's body at about the maximum practical distance of 6 ft downstream from the instrument is only about four widths away. In the Bureau of Standards paper previously mentioned, it is recommended that supports used in calibrations be at least 16 widths downstream. In practice, therefore, a downstream position of the observer is ruled out as far as accurate measurement is concerned. Operation of the anemometer by rigid shaft support from a point outside the section is seldom practicable; however, accurate results can be obtained, with the anemometer rigidly attached to a short shaft and held at arm's length, by an observer advancing across the traversed section while he faces the opposite wall and stands sideways to the current, provided that he keeps the instrument at least 3 ft away from his body at all times and traverses the entire section with it. If the traverse can be started with the observer in a side recess, the entire section can be covered in one operation. Normally, it would be covered in two half-sections. The presence of the observer's body does not, as is commonly supposed, increase the average velocity throughout the remaining part of the section. Rather, the velocities 1 to 2 ft on either side of his body are increased, but the distribution of velocities throughout the rest of the cross section remains normal, and a traverse made as stated gives a true average velocity for normal-flow conditions. Regarding the proper "method" factor for accounting for interference in the approximate methods of traversing with hand-held instruments, here again confusion prevails, for which the writer must assume some of the blame. Comparison of consecutive traverses made by shaft-held and hand-held 4-in. anemometers in field work after the tests reported by McElroy and Richardson' gave method factors

Jan 1, 1950

By L. W. McKeehan

The occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note.' This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. Method of Preparation The material in which the crystals here dealt with were grown was made from 1/8in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400" C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of traveling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, as nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection. Measurements The wire in the etched state was next mounted in a goniometer of special form which allowed the measurement of the spherical coordinates of the normals to any plane surfaces left by the etching. These coordinates were most conveniently a polar distance, 8, from one direction of the wire axis, and an azimuth or longitude, ?, from an arbitrary prime meridian. The region to be described more particularly is shown at a low magnification in Fig. 1, which gives two different views, differently illuminated to show the spatial relationship of a crystal occupying most of the part shown and of an inclusion, or rather a series of three inclusions suspected of being twins based on the principal crystal.

By H. M. Bannerman, E. N. Cameron

INTRODUCTION DURING the years 1942-1944, about 125 New England deposits were mined for sheet and punch mica, and many others were briefly prospected. During this period the Geological Survey, United States Department of the Interior, carried on detailed studies of the deposits and the pegmatite bodies that contain them. The primary purpose of the studies was to provide geological information that would contribute toward efficient mine development and operation. The studies were aimed directly at practical production problems. Detailed maps showing the structure of the deposits were prepared, and geological findings were closely correlated with data on specific yields and costs of mining and processing. The result is information that permits a reasonably accurate appraisal of the mica deposits of New England and the mining industry that they support. At a time when the future of the industry is in doubt, it seems desirable to submit this appraisal for consideration. Domestic mica deposits supply only a small fraction of the country's needs in normal times, for only the richest domestic deposits can compete with the low-cost mines of India and Brazil. However, the possibility that this country may be cut off from its supplies in time of war gives domestic deposits an importance much greater than their peacetime production would imply. New England supplied about 22 per cent of domestic output in 1943 and 1944, the peak years of wartime production. Its actual contribution to the war effort was greater, for the proportion of sheet mica of high quality in the New England product is higher than the average for domestic mica. The data analyzed below were collected for the Geological Survey by D. M. Larrabee, A. H. McNair, J. J. Page, V. E. Shainin, G. W. Stewart, and the co-authors of this paper. The cooperation of officials of Colonial Mica Corporation and of mine operators and owners in furnishing information is gratefully acknowledged. D. M. Larrabee, A. H. McNair, and V. E. Shainin have made various suggestions based on critical reading of the manuscript. ANALYSIS OF WARTIME OPERATIONS In considering the data presented in this report, it must be remembered that the scale of mica operations is very small compared with that of many other mining industries. The typical New England mica mine of 1943 and 1944 was worked by a crew of five or six men. Equipment was varied but on the whole extremely simple. The first stage of operation at a deposit was normally opencut mining. Drilling was done mostly with jackhammers powered by portable compressors driven by gasoline engines. Muck was shoveled by hand into buckets with a capacity of 1/3 to 2/3 ton and commonly hoisted by derrick to a dump adjacent to the cut. As operations were carried to greater depth, and the transition to underground mining was made, these methods were modified to a degree depending largely on the attitude of the deposit mined. At steeply dipping deposits,

Jan 1, 1946

While coal was mined in New Mexico in 1860, production was on a small scale during the period considered here, and Table 77 contains all the data found. [ ]

Jan 1, 1942

By Bieniawski, Z. T.

The importance of understanding the phenomena associated with rock fracture has long been fully appreciated in rock mechanics. This is clearly apparent from the special attention paid to rock fracture in the comprehensive papers published within the past four years. These papers present a picture of how the knowledge of brittle fracture of rock was gradually enriched and also show that what was often taken for granted three or four years ago is no longer considered as valid today.

Jan 1, 1972

By N. S. Wagner

The production of lightweight aggregates in Oregon is a new industry, and, like all new enterprises, it is suffering from growing pains characterized by numerous, small operations some of which flourish for a short time and then cease altogether. Normally all industrial mineral products are produced in a highly competitive atmosphere. At the present time this condition does not exist to a very marked degree in the state because as yet producers have not saturated the constantly expanding market. This paper has been prepared with the intention of outlining very briefly the current status of the various products now being used as lightweight aggregates in Oregon. The present picture will surely change, perhaps quite radically within even a short space of time.

Jan 1, 1949

By R. E. Boni, G. Derge

Application of surface tension measurements has been made to molten silicates in order to determine the effect of sulphur upon the surface tensions of synthetic blast furnace slags. In melts with the same molar ratios of AI2O3 + SiO2 to the basic oxides BaO, CaO, and MgO, the surface tensions increase in the order of oxides listed. Sulphur lowers the surface tensions of the basic BaO, basic CaO, acid BaO, acid CaO, and acid MgO slags in that order; and the concentration of excess sulphur at the slag surface increases in this same order of slags. The rate and amount of desulphurization of iron by these slags is favored by a low excess surface sulphur in the slag. IN a previous paper,1 the authors discussed the applications of surface tension measurements of molten silicates to problems of metallurgical interest. Of major importance is the aid that such studies lend to forming a working concept of slag structure. Since the ability of a slag to desulphurize metal depends strongly upon its composition,2"4 fundamental information about the structural differences between various slags which contain sulphur should aid the development of better desulphurizing media. For that reason, the present investigation concerns the effect of sulphur upon the surface tensions of synthetic blast furnace slags. Experimental Procedure , The maximum bubble-pressure method was used to measure the surface tensions of synthetic blast furnace slags in the temperature range 1300° to 1600°C. The method is based upon the equation which was developed by Schrödinger5 from a consideration of the forces of hydrostatic pressure and surface tension of a liquid which oppose bubble formation when a gas is forced through a tube immersed in the liquid. where y is the surface tension between argon and slag in dynes per centimeter; g is the gravitational constant, centimeters per second2; H is the manometer reading in centimeters; s2 is the density of manometer fluid in grams per cubic centimeter; S1 is the density of the medium in grams per cubic

Jan 1, 1957

By Arthur F. Johnson

Plant sites for the light metal industry must be located where ample low cost power is available. In the first half of the century hydroelectric development was the only source of this power-now the best sites have been exploited and those remaining do not promise enough water to permit year-round capacity power plant operation. In searching for economic plant sites engineers have concentrated on locations with vast water power potential. Olin Mathieson Chemical Corp. has been studying the economics of developing water power to make aluminum. However natural gas, lignite, and even atomic energy have also been considered as possible power sources for aluminum production. Economic studies have given consideration not merely to investment and production costs, but to total costs of delivering fabricated products to the market center of the U. S. When delivered costs are considered and when full account is taken of the newest techniques of mining bituminous coal and utilizing it to make electric power, one arrives at the inescapable conclusion that coal has emerged as the economic answer to American aluminum production.

Jan 4, 1955

By W. J., Kroll

MOST people believe that rare metals are always, scarce in nature, expensive to make, and therefore useless despite some miraculous properties which might make them a cure-all. There are' some metals, which are quite frequent in nature, such as zirconium, which are called rare only because our present methods for making them are elaborate, thus forcing the manufacturer to sell them at a high price. There are also truly rare metals, such as gallium, which do not occur frequently in ores, but are easily reducible from their oxides. In these cases the price of the concentration operation is the decisive factor. The distribution of the elements in the earth's crust is no indication as to the availability of a metal; the concentration operation is the critical factor. Concentration is frequently obtained in the course of metallurgical operations for the extraction of other metals, and the rare metal may be enriched in by-products, flue dusts, mother liquors or precipitates from electrolyte purification as are indium, thallium, selenium, and tellurium. A periodic table of the rare elements may serve as a basis for discussion of their properties and to establish a program. (Table 1.)

Jan 1, 1946

By D. H. Forbes, I. B. Cadoff, H. M. Manasevit

Single-crystal silicon films have been obtained on several natural crystal faces of BeO using the thermal decomposition of silane and the hydrogen reduction of silicon tetrachloride. From an analysis of X-ray diffraction data it was determined that the following film-substrate orientation relationships exist: (111) Si 11(0001) BeO, (111) Si 11(1011) BeO, (100) Si 11f1010) BeO. and (110) Si 11(1010) BeO. An analysis of the crystallographic relationships between the film and substrate indicates that a match occurs between the silicon atoms in the film and the berylliuni ion sites in the substrate. This correspondence is in agreement with previous work on the deposition of silicon on sapphire.1-3 silicon on spinel: and tungsten on sapphire. The high resistivity, thermal conductivity, and radiation resistance of beryllium oxide make it an important substrate material for the deposition of thin films of silicon or other semiconductors. The importance of semiconductor-insulator composites to the field of integrated microelectronics has been well-documented in the case of silicon on sapphire.'-' The successful growth of large-area single-crystal silicon on an insulator, sapphire, was first reported in 1963.1,2 Since that time studies have been made of the crystallographic relationships between the deposited film and the sapphire substrate. On the basis of the observed relationships, a model has been proposed relative to the crystallographic requirements for epitaxy between the semiconductor film and the metal oxide substrate.3 It is proposed in this model that epitaxy is the result of a match between atoms of the deposited film and the metal ion sites of the substrate plane. This match is not limited to a 1 to 1 correspondence between sites in the two lattices. Sub- sequent studies of the deposition of silicon on spinel4 and tungsten on sapphire5 have yielded data which support this model. On the basis of this previous work it was felt that silicon on BeO should also fit this model. In the present study, the choice of substrate orientation was limited to the natural faces of synthetic BeO crystals. Of the faces available, the (0001) plane seemed the most favorable for epitaxial growth. EXPERIMENTAL PROCEDURE Silicon films were deposited from silane and silicon tetrachloride in the apparatus shown in Fig. 1. The hydrogen ambient gas was purified by passage either through a DEOXO unit, molecular sieves, and a liquid nitrogen cold trap, or through a heated Pd-Ag thimble. The gas was then mixed with the silicon source materiai and passed over the substrate which lies on a spacer above an inductively heated silicon pedestal. The following deposition conditions were used: a hydrogen flow rate of 3 liters per min with silane and silicon tetrachloride concentrations of 0.2 mole pct and a pedestal temperature of 1175" * 5°C as observed with an optical pyrometer assuming an emissivity of 1.0. Deposition was preceded by a 15- to 30-min hydrogen-etch period conducted at a temperature of 1275°C (obs). Adherent silicon films from 2 to 10 u were grown on the various BeO faces. The substrates were synthetically grown beryllium oxide single crystals ranging from 5 to 10 mm in

Jan 1, 1967

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

By David B. Reger

Wildcat drilling for new supplies of gas and the expansion of previously discovered oil and gas pools were the principal petroleum activities in West Virginia .during 1942. Much of the new gas exploration is still uncompleted and still indecisive but various wildcats made substantial extensions to existing pools. Out of 53 wildcats drilled 27 resulted in commercial gas and 6 in commercial oil. Four of the oil discoveries also had commercial gas. No strictly new pools of oil or gas can safely be described as discovered but several scattered oil and gas wells previously drilled have been confirmed as the openers of definite pools; also, various completions closed wide gaps between apparent gas pools already discovered. The proved oil territory of the state was increased about 4850 acres and the proved gas territory about 51,000 acres. The new proved oil reserves should about balance withdrawals and the new gas may represent a substantial increase. Aside from the drilling in four rather lively pools, oil activity was slight because of unfavorable operating conditions and prices. Gas drilling also declined for reasons beyond the control of the operators. The account of operations, as gathered from trade journals and other reporting services, shows that 797 new wells were drilled, providing 119 new oil wells with 2762 bbl. of daily new production; 536 new gas wells with 1,228,501,000 CU. ft. of daily open flow: and 142 dry holes. Also... 76 old wells were drilled to deeper sands, with 71 bbl. and 26,034,000 cu, ft. of added production. On the new wells the oil average was 23.21 bbl. per well per day; and the gas average was 2,270,406 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 17.82 per cent. On deeper drilling the ratio of failures was 21.05 per cent. Production of oil for the year was estimated by the Oil ad Gas Journal as 3,492,000 bbl., as compared with 3,378,000 bbl. in 1941. Production of natural gas for the year is estimated by the author as 220,000,000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 207,000,000,000 cu. ft.* in 1941. General State op Industry Leasing of wildcat acreage increased considerably. The total land of all classes under lease may now exceed 5,000,000 acres. Taking into consideration completions, abandonments and corrected figures or estimates, Table I shows cumulative and late annual statistics. New Pools and Extensions Table 2 shows the principal areas of drilling activity during 1942. Various consolidations of territory, hitherto treated as separate pools, have been made. in addition to these active pools, extensive drilling was done in numerous other areas where pool boundaries can hardly be defined. Summary or Exploration Table 3 gives a summary of important wildcat or exploratory wells drilled during

Jan 1, 1943

By H. T. Sumsion, A. U. Seybolt

The results of an investigation of vanadium-rich V-O solid solutions are presented, indicating the structure and lattice parameters of two solutions, a and ß, and their approximate temperature-composition existence. The a solution is the terminal body-centered cubic one, and contains up to 3.2 atomic pct 0. The ß solution has an ordered body-centered tetragonal structure, is formed at 1270°C, and exists from about 15 to 22 atomic pct 0. From the evidence available, the various phase boundaries have no appreciable temperature dependence. Evidence has been found for a polymorphic transformation in pure vanadium at 1550°C. IN an earlier investigation' dealing with the preparation of pure vanadium by calcium reduction of the oxide, it was found that small amounts of oxygen drastically reduced the ductility of the metal. Because this effect was so marked, it was decided to make a study of the solubility of oxygen in solid vanadium. This report deals principally with this solubility and the nature of the phase relationships in the vanadium-rich region, particularly at temperatures below 1300 °C. However, during the investigation enough data on the V-0 system were obtained to make it appear worthwhile to present a tentative phase diagram up to the composition VO. The only significant prior work found on this system are the contributions of Klemm and Grimm,' and Mathewson et al.3 Klemm and Grimm prepared a wide range of V-O compositions by powder techniques including the compositions VO.l, VO.2, VO.3 and VO4 (9.1, 16.8, 23, and 28.6 atomic pct 0, respectively). The first three compositions were found to consist of a body-centered tetragonal solid solution, while the last also showed lines of VO (NaCl structure). They found that the parameter c, increased and the parameter a, decreased with increasing concentration of oxygen. For their composition VO.27, or about 16.8 atomic pct O, they cite the values a, = 2.948A, c, = 3.53A, and c/a = 1.2. Klemm and Grimm made no attempt to determine the solid solubility limit nor to construct a phase diagram. They did, however, give some data on the homogeneity range of VO, and they proposed a structure for the body-centered tetragonal solid solution; these points will be taken up later. Materials and Preparation of Samples The vanadium used in this investigation was prepared in the laboratory by the method previously mentioned.' A typical analysis is as follows: Fe, 0.007 pct; Si, 0.02; Ca, 0.06; C, 0.224; O2, 0.044; N,, 0.0017; H2, 0.003; and V, 99.34 ±0.3 (assay). The vanadium assay is probably low by about the error given. The impurities total about 0.36 which, if subtracted from 100, gives a purity of about 99.6. At the time material was being prepared for this work no suitable technique was available for melting vanadium without appreciable contamination. The procedure adopted therefore was to cut the calcium-reduced regulii into slices which were then rolled to strip about 0.025 in. thick for oxygen diffusion. Pieces of rolled vanadium of approximately 0.025xY4xl in. and weighing about 0.3 g were suspended in a vertical fused-silica tube which was part of an ordinary gas absorption apparatus. The silica tube was heated by an electric resistance-tube furnace which could be raised around the silica tube or lowered away from it as desired. This apparatus had no novel features which require detailed description. Other than the silica tube and furnace, it consisted of a glass system evacuated by a liquid nitrogen trapped mercury diffusion pump, a mercury-operated gas burette, a McLeod and a Pirani gage, and a mercury manometer. It was also equipped with suitably located stopcocks for isolating various parts of the system; the vacuum ordinarily attained was between 10" and 10-6 mm of mercury. Oxygen generated by decomposing MnO2 was passed through anhydrous magnesium perchlo-rate before introducing it into the gas burette and thence to the absorption chamber.

Jan 1, 1954

By H. A. Doerner, F. D. DeVaney, J.B. Clemmer

Production of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaC03) and dolomite (MgCO3. CaC03). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedra1 crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent SiO2, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 SiO2 and 6.5 R2O3. The percentage reported as R2O3 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe2O3, A1203 and TiO2. The sorted magnesite product is not the best grade. even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1943

By J. B. Clemmer, F. D. DeVaney, H. A. Doerner

Production of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaC03) and dolomite (MgCO3. CaC03). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedra1 crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent SiO2, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 SiO2 and 6.5 R2O3. The percentage reported as R2O3 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe2O3, A1203 and TiO2. The sorted magnesite product is not the best grade. even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1943