Search Documents

By Williams, J. A.

THE Alaska Juneau mine has been developed through an adit driven at the elevation of the top of the mill and all mining is done above this main haulage level. As a result of wholesa1e"mining operations about 11,000 tons rock containing one dollar' per ton in gold is, hauled to the. concentrator during every 24 hr. Due to the method of mining, whereby a system of oreways delivers-the.ore direct from the stope to the bottom level of the mine, no tramming of ore is done on any of the upper levels. However, ;in doing exploratory drifting and crosscutting on the upper levels, the broken material is trammed by hand in 1-ton 18-in. gage cars to a nearby raise connecting with one of the several oreways. This constitutes the only tramming operation except that on the main level.

Jan 1, 1931

By Gilbert P. Moore

The production of petroleum in Argentina during 1932 was greater than in any preceding year. The total amount produced was 13,012,-756 bbl. This figure represents a decided increase in the production of oil in Argentina and can be attributed largely to the increased activities of the Royal Dutch operations at Kilometer 27 in the Comodoro Rivadavia district and those of the Standard Oil Co. of Argentina in the Salta region. Production from the Royal Dutch wells amounted to considerably more than 10,000 bbl. per day over quite a long period during the year. Of the 13,012,756 bbl. of oil produced during 1932, the Government Agency (Y. P. F.) was responsible for some 5,578,954 bbl., while 7,433,-802 bbl. were produced by private companies. Although in 1930 the Y. P. F. produced about 55 per cent of the total production and in 1930 50 per cent of the total, in 1932 its production had fallen to about 42 1/2 per cent of the total. This decrease in the proportion produced by the Y. P. F. was not due to a decrease in its production but to the decided increase in the production of private companies, particularly those two whose names are given above. One new discovery was recorded during the year. This was a well drilled by the Y. P. F. at Cacheuta in the province of Mendoza which came in pumping 80 bbl. of 15" gravity oil from a depth of 673 meters. This well was completed at approximately the same time that the provincial government of Mendoza granted a concession to the Y. P. F. and declared the whole province as a reserve in which no concessions may be granted for a period of 10 years. Under these conditions, the federally operated Y. P. F. will have no competition in the Cacheuta area from private companies such as they have in the other three fields of the republic. The Y. P. F. wildcat west of Comodoro Rivadavia at Pampa Maria Santissima on the Rio Senguerr was completed as a dry hole during 1932. This we11 was reported as a producer in 1930 by persons returning to this country from Argentina but it appears that they had been misinformed. The site of this test has been abandoned and a new location made north of the Rio Senguerr.

Jan 1, 1933

By H. W. Straley

Some ten years ago the writer1 made a survey of college catalogues to determine what sort of training geologists were receiving in basic sciences. In the light of this compilation and subsequent experience, he made the statement at the 1939 meeting of the Institute that apparently only in schools offering a curriculum in geological engineering or in the geological option of mining engineering curricula could geologists hope to receive the training advocated by Hubbeet.2 In the former study, schools of engineering were excluded because the preparation was known beforehand. The present study aims to consider engineering schools in an effort to determine not only what basic studies are required but what use is made of them in geological courses of the third and fourth years. The present study combined the method of consulting catalogues with a questionnaire. Letters were mailed to officials responsible for supervision of mineral industries curricula requesting information On' (I) the extent to which the engineering preparation of the first two years is actually used in the work of the last two; (2) the extent to which the engineering of the last two years is used in courses in geological engineering or geology; and (3) whether geologists or geological engineers teach descriptively or analytically. Both methods of securing information are open to criticism; the former on the basis of the incomplete information supplied by university catalogues concerning prerequisites and curricula and the latter on the ground that the questions may be phrased poorly or given insufficient consideration by replying officials. Fifty-six questionnaires were mailed and 39 (70 per cent) replies were received. Of the replies, 6 (11.3 per cent) were from colleges of liberal arts unconnected with engineering schools, 11 (20 per cent) were from schools having curricula in geological engineering and 22 (39 per cent) were from departments of mining engineering. The number of replies and their distribution were satisfactory in spite of the receipt of only six from liberal arts colleges. It should be understood that the universities of which the catalogues were examined were not necessarily the same in both compilations. No departments that are admittedly or known to be acting solely as service departments were recorded in the second study. Table I shows that all professional schools require mathematics through calculus, whereas only 7 per cent of the liberal arts curricula expect the same level of preparation; only 73 per cent require trigonometry and 40 per cent college "algebra. The proportion of geological engineering curricula requiring differential equations is higher than mining. All of the engineering schools require general and analytical chemistry, whereas only 77 per cent of liberal arts curricula require general and 18 per cent analytical. Twenty-two per cent of the mining and 40 per cent of the geological engineering

Jan 1, 1946

By H. W. Straley

Some ten years ago the writer1 made a survey of college catalogues to determine what sort of training geologists were receiving in basic sciences. In the light of this compilation and subsequent experience, he made the statement at the 1939 meeting of the Institute that apparently only in schools offering a curriculum in geological engineering or in the geological option of mining engineering curricula could geologists hope to receive the training advocated by Hubbeet.2 In the former study, schools of engineering were excluded because the preparation was known beforehand. The present study aims to consider engineering schools in an effort to determine not only what basic studies are required but what use is made of them in geological courses of the third and fourth years. The present study combined the method of consulting catalogues with a questionnaire. Letters were mailed to officials responsible for supervision of mineral industries curricula requesting information On' (I) the extent to which the engineering preparation of the first two years is actually used in the work of the last two; (2) the extent to which the engineering of the last two years is used in courses in geological engineering or geology; and (3) whether geologists or geological engineers teach descriptively or analytically. Both methods of securing information are open to criticism; the former on the basis of the incomplete information supplied by university catalogues concerning prerequisites and curricula and the latter on the ground that the questions may be phrased poorly or given insufficient consideration by replying officials. Fifty-six questionnaires were mailed and 39 (70 per cent) replies were received. Of the replies, 6 (11.3 per cent) were from colleges of liberal arts unconnected with engineering schools, 11 (20 per cent) were from schools having curricula in geological engineering and 22 (39 per cent) were from departments of mining engineering. The number of replies and their distribution were satisfactory in spite of the receipt of only six from liberal arts colleges. It should be understood that the universities of which the catalogues were examined were not necessarily the same in both compilations. No departments that are admittedly or known to be acting solely as service departments were recorded in the second study. Table I shows that all professional schools require mathematics through calculus, whereas only 7 per cent of the liberal arts curricula expect the same level of preparation; only 73 per cent require trigonometry and 40 per cent college "algebra. The proportion of geological engineering curricula requiring differential equations is higher than mining. All of the engineering schools require general and analytical chemistry, whereas only 77 per cent of liberal arts curricula require general and 18 per cent analytical. Twenty-two per cent of the mining and 40 per cent of the geological engineering

Jan 1, 1946

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1937

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers ' and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1944

By Michael B. Bever, John R. Anderson

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By John R. Anderson, Michael B. Bever

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By John R. Anderson, Michael B. Bever

CARBON may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,1 the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. EARLIER DATA The solubility of carbon in molten pure copper is about 0.0001 pct at 1100 °C and 0.0004 pct at 1475°C.1 Various authors2-6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range 1217° to 1245°C. This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By R. W. Raymond

(Pittsburg Meeting, March,1910.) THE Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mice. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising, 15 ft. of sinking was done so that the bearers, collar-set, and three shaft-sets might be installed and concreted, and with this done it was possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 ft. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. air-hoist *as installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21. ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8- by 8-in, struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two, sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jun 1, 1910

By C. Everard Arnold

The Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mine. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising; 15 ft. of sinking was done so that the bearers, collar-set, and three shaftrsets might be installed and concreted, and with this done it mas possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 f't. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. airhoist was installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21 ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8-by 8-in. struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jan 1, 1911

By A. S. Venkatadri, H. B. Bell

The equilibrium sulfur distribution between molten iron and Ca0-Mg0-Al203 slags containing iron oxide was investigated at 1550°C. The results were used to derive the iron oxide activities at low iron oxide concentrations in the slag by combining the sulfide capacity data obtained from gas-slag work with the free energies of both the sulfur solution in iron and the iron oxide formation in slag. The derived ferrous oxide activities were compared with values based on Tem-kin's kin's and Flood's ionic models. One difficulty in using these models is that the nature of the aluminate ion in slag is uncertain. Nevertheless, such indirect methods, in particular, those described in the present paper, are of value because of the difficulty of measuring small amounts of oxygen in liquid iron in equilibrium with slag. It is shown that these methods confirm the consistency of thermodynamics data on liquid iron and slags. It is well established that decreasing the iron oxide activity in the slag increases the desulfurization of molten iron at constant slag basicity. This effect is most pronounced at the very low iron oxide activities, characteristic of blast furnace slags. Yet a precise quantitative determination of the significance of low iron oxide contents in slag in blast furnace desulfuri-zation is not possible for the following reasons: a) difficulty of separation of iron "shots" from the slag, and b) errors in chemical analysis of small amounts of iron oxide in slags. In view of these obstacles, one must resort to indirect methods of calculating iron oxide activities. EXPERIMENTAL TECHNIQUE The apparatus for providing the sulfur equilibrium data has been described previously1 and was similar to that used by ell' in connection with the study of slag-metal manganese equilibrium. The procedure consisted of: a) melting about 50 g of Armco iron in a magnesia crucible in a platinum furnace, b) adding a mixture of about 15 g of lime-alumina slag and varying amounts of Fe2O3 and CaS, and c) maintaining the temperature at 1550°C for more than an hour in an atmosphere of argon to enable the sulfur equilibrium to be attained. Several melts were made using lime-alumina slags with basic composition 55, 50, and 45 pct lime. During the experiment the temperature was controlled manually using a Pt/10 pet Rh-Pt thermocouple. After the experiment, the Power was shut off and the flow rate of argon was increased to freeze the melt as quickly as possible. The analysis of sulfur in the metal was carried out by the oxygen combustion method3 using uniform drillings from the top and bottom of the metal button. After crushing and grinding and removal of any iron particles with the aid of a hand magnet, the slag was analyzed for sulfur by the CO2 combustion method.4 The E.D.T.A. method was employed for the analysis of lime5,6 and magnesia,= the ceric sulfate method7 for the analysis of slag iron oxide, and the perchloric acid dehydration method5 for the analysis of silica. The remaining amount was taken to be Al2O3 precipitation with ammonium hydroxide in several preliminary melts had confirmed the propriety of using this simple procedure. RESULTS The activity of iron oxide in binary, ternary, and more complex slags has been the object of numerous investigations, and the two experimental methods for its determination are: 1) Equilibrating the metal with the slag in question and measuring the oxygen content of the metal. The ferrous oxide activity is then given by aFeO L%OJSat where [%0]sat is the oxygen content of the metal in equilibrium with pure iron oxide slag. This method was used by Chipman et al.8,9 2) Equilibrating the slag in iron crucibles with known partial pressures of H2/H2O or CO/CO2 mix-tures.10-12 This method is limited to temperatures between 1265" and 1500°C. The very low oxygen content of the melts in this investigation made it impossible to derive the ferrous oxide activity by the first of these methods. Therefore, the iron oxide activities were computed by means of: Sulfide capacity data from the gas-slag work" Temkin's concept14 Flood's approach15 a FeO from Sulfide Capacity. The method of calculating the aFeO involves the sulfide capacity of the slag (c,), the sulfur distribution coefficient (Ls), the free energy of dissolution of sulfur in iron, and the free energy of formation of iron oxide in the slag. Bell and Kalyanram13 have investigated the sulfur absorption characteristics of lime-alumina slags containing magnesia by the Carter-Macfarlane method16 (based on comparing the sulfide capacity of the slag in question with that of a standard slag of unit lime activity) and have derived lime activity values. The relation between sulfide capacity and their lime activity a'CaO is given by: Cs= 3—: Xa'CaO at 1500°C

Jan 1, 1970

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the, Committee.

Jan 1, 1946

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1946

By B. F. Fackenthall

The Durham Iron Works of Messrs. Cooper & Hewitt, near Riegelsville, Pa., occupy a site which has been almost continuously the scene of iron-manufacturing industry since 1727. Doubtless if Anthony Morris and his thirteen associates, who in that year erected a blast-furnace on the Durham Creek, a short distance above where the Durham Iron Works now stands, could have had a vision of the improved and enlarged apparatus of their successors, they would have been not less astonished by the huge stack, the hot-blast ovens, and the blowing-engines of the modern blast-furnace, than by the railroad which now follows the bank of the river on which their clumsy " Durham boats " once floated pig-iron to Philadelphia. In one particular, posterity must confess their snperiority. We are told that in November, 1728, they shipped three tons of Durham iron to England. The proprietors of the Durham Iron Works are not now shipping iron to England. The present Durham furnace was built (in place of two smaller ones) in 1874 and 1875, and made its first blast in 1876. A description of it, with other works of the same proprietors, at Trenton, N. J., by A. L. Holley and Lenox Smith, was published in London Engineering for January 31st, and February 21st, 1879. Since that time, a number of improvements, dictated by experience, have been made in the details of the furnace and fittings; and the recent roilclusion of a long and successful blast presents a convenient opportunity for a description of the works and a statement of the results of practice. The accompanying drawings will show the general arrangement of the works. The furnace, Plate I., Figs. 1 and 2, is 75 feet high by 19 feet bosh. The hearth is 11 feet 4 inches in diameter, with seven tuyeres 5 feet 6 inches above hearth-line. The tuyeres project 9 inches into the furnace, making the interior tuyere-circle 9 feet 10 inches in diameter. The front is a modification of Luermaun's

Jan 1, 1886

By W. Mostowitsch, H. O. Hofman

The mineral gypsum, CaSO4 + 2 H2O, has been used for many years as a sulphurizing and basic flux in several smelting-operations. Thus, in smelting oxide nickel-ore in the blastfurnace, it is commonly added to the charge to furnish the sulphur necessary for collecting the metal in a matte, and a base for slagging the siliceous gangue. In the concentration of lead-copper matte in the reverberatory furnace it has been used for years at Preiberg, Saxony,1 for a similar purpose, and for producing at the same time a copper-matte with less than 0.15 per cent. of Fe. The latest use gypsum has been put to is in the blast-roasting process of Carmichael-Bradford.2 The term " blast-roasting," given by A. S. Dwight3 to the Dwight-Lloyd method of roasting and agglomerating: is a happy generic term which covers the ground better than the " lime-roasting " of Ingalls5 or the " pot-roasting " of Austin: in that it leaves the operation independent of the character of the flux and the form of apparatus, and retains the characteristic feature of this class of processes—namely, that of using forced draft. In the Carmichael-Bradford process the dehydrated material, mixed with galena-concentrate, acts as a diluent and a flux. The process differs in this from the Huntington-Heberlein7 and the Savelsberg8 processes, in both of which limestone is used.

Jan 1, 1909

By Vsevolod Krivobok

THE re-crystallization of metals has been the subject of much scientific investigation, some of which has resulted in a better understanding of this extremely important and interesting phenomenon. Unfortunately, while many have propounded theories of re-crystallization, but a few have presented experimental evidence as to how it takes place. If this can be determined the question, why re-crystallization occurs, may be answered more definitely. Re-crystallization in single phase metals consists of a complete rearrangement and re-sizing of the grains, of which the structure is composed, while the type of structure remains the same. That is to say, if the structure before re-crystallization is composed of a number of polyhedral grains of different shape and size, a particular spot after re-crystallization will be seen to consist of grains in no way different from the original except in size and shape. The re-crystallized grains may be smaller or larger, depending on the treatment received; and, while the re-crystallization may be brought about by means of heat treatment only in passing through a critical range, yet it is common knowledge that single phase metals subjected to cold working are possessed of a tendency toward re-crystallization, even if the heating does not reach critical range. The study of re-crystallization would, of course, be much easier if we had single crystals of any metal as the original material with which to study the phenomenon of re-crystallization, since it would permit the observation of structural changes at what amounts to enormous magnification, by changing the scale of the specimen. In metals of more normal grain size the crystal boundaries introduce complications, but the process, it may be assumed, is essentially the same. Such an opportunity

Jan 2, 1926

By G. A. Beiswenger

The application of the law of supply and demand to the sale of crude oil is generally conceded, but the motives underlying the buyer's (refiner's) demands are not always obvious to the seller (producer). In some cases this obscurity has led to the conclusion that the refiner may be unnecessarily particular when he selects one crude and rejects another. This preference, however, is very largely the reflection of the refiner's product demands and the quality of the stocks obtainable from the selected crude. The purpose of this paper is to point out critical characteristics of the major classes of refined products and to show how crudes vary in their suitability for such products. With relatively few exceptions, available processing methods and addition agents make it theoretically possible to produce any type of refined product from any crude source, although it may not be economi-cally sound to do so. The widespread application of thermal cracking for converting higher boiling stocks into gasoline is well known. More recently cracking and refining in the presence of catalysts9 have been developed, as well as various processes for polymerizing lighter hydro-carbons into gasolines having desirable characteristics.6 For several years, selective solvents have been applied commercially to refining inferior quality kerosene, Diesel fuel and lubricating oil distillates .3 Improved methods for refining lubricating oils from crude residua,4 formerly suitable only for fuel, are now in use and a number of special solvent processes are available for dewaxing lubricating oils to low pour point.5 These improved refining methods have been developed not only to meet the demand for improved product quality but also to enable the refiner to obtain quality products from crude sources that would not yield such products by the older refining methods. In many cases, the utilization of these modern refining tools necessi-tates an appreciable expenditure for equipment as well as added manufac-turing costs, and their application therefore must be justified economically. Despite the availability of such tools, the added processing costs involved and yields obtainable may render their application entirely impractical. To illustrate this point, inspections of typical cuts from various crudes

Jan 1, 1940

G. F. LOUGhlin,* Washington, D. C.—With reference to Mr. Bain's paper: The scarcity of adequate geologic data on building stone reflects, among other things, a lack of interest on the part of geologists. It has been one of my duties to attend to matters relating to building stone and other structural materials that have come to the U. S. Geological Survey, but for several years my principal administrative and other duties in the Section of Metalliferous Deposits have prevented me from giving structural materials the attention that they deserve. I have felt that investigations relating to structural materials should be assigned to someone else, but thus far nobody with a sufficient interest in the subject has come forward; further, the specific calls for these investigations have been so few and far between that it has not seemed practical to draft any one for the job. The general situation is such that steady and substantial progress in the application of geology to the utilization of structural materials is not likely to be made unless someone with keen interest in the subject takes the initiative. If the start is once made, I know from experience that cooperation from the more progressive members of the quarry and building industries will be readily forthcoming. Mr. Sales' suggestions are all constructive and most welcome. A thorough, detailed discussion of them might be as long as his manuscript, but could largely be summarized with the one word "amen" qualified by the alibi that a chronic shortage of funds and therefore of personnel has prevented us from carrying out some of his suggestions already. A few of them might call for an Act of Congress before we could undertake them, and one or two, such as the preservation of mine maps, with which I heartily agree, would call for much additional space as well as clerical and supervising help. Several items in Mr. Sales' paper—for example, the question of balance between the scientific and more directly practical studies and the surveys or resurveys of the larger and smaller mining districts—have been covered in my contribution to the symposium. The suggestion of frequent reviews of progress in the study of ore deposits is excellent and can be followed without serious diversion from projects already on the Survey's program. Brief reviews by Survey men have been published in periodicals, and the contributions by several of them to the Lindgren Volume1 may also be cited as serving this purpose to some degree. The practice of publishing short papers by Survey men in outside journals rather than in Government reports is largely the result of experience and expedience. Our printing funds are limited, and considerable time must elapse between the transmittal of a paper and its publication. Time is saved therefore by sending papers to outside journals, and the editors of those journals are usually glad to receive them. Members of the Survey would doubtless prefer to have the products and byproducts of their official work appear in official Survey publications if conditions were more favorable. If we were left entirely to ourselves the balance between the more scientific and the more directly practical studies would be somewhat better than it is, but the

Jan 1, 1935

G. F. LOUGhlin,* Washington, D. C.—With reference to Mr. Bain's paper: The scarcity of adequate geologic data on building stone reflects, among other things, a lack of interest on the part of geologists. It has been one of my duties to attend to matters relating to building stone and other structural materials that have come to the U. S. Geological Survey, but for several years my principal administrative and other duties in the Section of Metalliferous Deposits have prevented me from giving structural materials the attention that they deserve. I have felt that investigations relating to structural materials should be assigned to someone else, but thus far nobody with a sufficient interest in the subject has come forward; further, the specific calls for these investigations have been so few and far between that it has not seemed practical to draft any one for the job. The general situation is such that steady and substantial progress in the application of geology to the utilization of structural materials is not likely to be made unless someone with keen interest in the subject takes the initiative. If the start is once made, I know from experience that cooperation from the more progressive members of the quarry and building industries will be readily forthcoming. Mr. Sales' suggestions are all constructive and most welcome. A thorough, detailed discussion of them might be as long as his manuscript, but could largely be summarized with the one word "amen" qualified by the alibi that a chronic shortage of funds and therefore of personnel has prevented us from carrying out some of his suggestions already. A few of them might call for an Act of Congress before we could undertake them, and one or two, such as the preservation of mine maps, with which I heartily agree, would call for much additional space as well as clerical and supervising help. Several items in Mr. Sales' paper—for example, the question of balance between the scientific and more directly practical studies and the surveys or resurveys of the larger and smaller mining districts—have been covered in my contribution to the symposium. The suggestion of frequent reviews of progress in the study of ore deposits is excellent and can be followed without serious diversion from projects already on the Survey's program. Brief reviews by Survey men have been published in periodicals, and the contributions by several of them to the Lindgren Volume1 may also be cited as serving this purpose to some degree. The practice of publishing short papers by Survey men in outside journals rather than in Government reports is largely the result of experience and expedience. Our printing funds are limited, and considerable time must elapse between the transmittal of a paper and its publication. Time is saved therefore by sending papers to outside journals, and the editors of those journals are usually glad to receive them. Members of the Survey would doubtless prefer to have the products and byproducts of their official work appear in official Survey publications if conditions were more favorable. If we were left entirely to ourselves the balance between the more scientific and the more directly practical studies would be somewhat better than it is, but the

Jan 1, 1935