Search Documents

By Shiou-Chuan Sun

THE fact that coals of different ranks and even of the same rank differ greatly in their amenability to iroth flotation is well known. In recognition of the need for an explanation of this phenomenon, two hypotheses have been suggested. Wilkinsl reported that the floatability of coals increased with an increase of the carbon content or rank. This postulate is handicapped by the fact that bituminous coals that possess moderate carbon contents are actually more floatable than anthracite coals that have high carbon contents, as shown in columns 6 and 9 of Table I. Taggart and his associates' implied that the difference of floatability between bituminous and anthracite coal was caused by the variation of carbon-hydrogen ratio. This is not applicable to the relative floatability of other coals and carbons. For example, column 11 of Table I shows that the carbon-hydrogen ratios of low-floating lignitic coal and non-floating animal charcoal are not only smaller than the moderate-floating anthracite coal, but are also similar to the high-floating bituminous coal. Furthermore, according to this hypothesis, high temperature coke-A (464), Ceylon graphite (1238), and lamp-black (357), all possessing extremely high carbon-hydrogen ratios, should be less floatable than other substances having much lower carbon-hydrogen ratios such as high volatile-B bituminous coal (11.9 to 22), anthracite coal (35.7 to 60.5), lignitic coal (15.6 to 33.6), and charcoal (13 to 26.2). However the former group is actually more floatable than the latter group. In this paper, a surface components hypothesis is Proposed to explain the different floatabilities of coals, carbons, and hydrocarbon minerals. The validity of the hypothesis is experimentally supported by the actual floatability, natural floatability, wettability, and adsorbability for neutral oils of coals, carbons, and hydrocarbon minerals tested. The combustible recovery of the flotation results, as used in this paper. was calculated from Eq. 1: P (100-Ep) 100 RWCP Rc= [1] F (100-E,) C, where R, is the percent combustible recovery; F and P are, respectively, the weight of feed and the weight of concentrate or product; E, and Ep are, respectively, the total percent of ash plus moisture in feed and in concentrate; Ru. is the percent weight recovery: and C, and C, are, respectively, the percent of combustible in feed and in concentrate. Except for ash and moisture content, all chemical components of a coal are assumed combustible. The experimental work included studies on flotation, ultimate and proximate analyses, contact angle tests, extractions of bitumen-A with benzene, adsorptions for liquid hydrocarbons, and wetting tests. Most of the flotation experiments were performed in a laboratory Fagergren machine; others were tested in a small Denver machine. The solid feed for the former was 300 g and for the latter was 30 g. The solid materials used for flotation were crushed to —48 mesh. After the mineral pulp in the flotation cell was agitated for 6 min and the pH was adjusted to 7.5 & 0.2 with sodium hydroxide or hydrochloric acid, a petroleum light oil having a viscosity of 5.73 centipoises at 77 °F was added and conditioned for 2 min. Finally, pine oil was introduced and the froth was collected for exactly 3 min. The weight ratio of petroleum light oil to pine oil was kept constant at 1.5 to 1. Tap water was used for all flotation tests. Contact angles were measured with a captive bubble machine. For each coal sample, three specimens were mounted in transoptic mounts and polished with levigated alumina, first on a sheet glass, then on a cloth-covered metal polishing wheel. The polished specimen was first washed with distilled water and wiped thoroughly on a cleaned linen pad, then transferred into the pyrex cell of the captive bubble machine and conditioned for 6 min., and finally measured for contact angles at three or more points. Except where otherwise stated, the induction time for each measurement was 1 min. The contact angle representing each material was obtained by averaging the measurements of three specimens. The linen pad was first washed with warm distilled water, then boiled 30 min in a 2N sodium hydroxide solution, and finally washed with distilled water until no trace of sodium hydroxide could be detected in the decanted solution. The cleaned linen pad was stored under distilled water. Immediately before using, the pad was rewashed and transferred into a clean pyrex petri dish partly filled with distilled water. The glassware and rubber gloves used were cleaned by soaking in sulphuric acid-potassium dichromate cleaning solution, followed by rinsing with distilled water. The polished specimens were handled only by glass forceps. The ultimate and proximate analyses were made in accordance with the ASTM standard procedures for coal and coke. The extractable bitumen-A was determined by weighing 1 g of —100 mesh sample and placing it in a desiccated and weighed ASTM aluminum-extraction thimble. The thimble was placed in condenser hooks and inserted into an extraction flask containing 100 cu cm of benzene. The flask was heated and the benzene vapor was condensed by water coils. At the end of 24 hr of percolation, the thimble was removed, desiccated, and weighed. Loss in weight of sample was taken as bitumen-A and calculated to dry and ash-free basis.

Jan 1, 1955

AT the Tulsa meeting of the A. P. I., the following reso-lutions, expressive of the policy of that organization, were among those adopted: RESOLVED, That we endorse the conclusion of the Federal Oil Conservation Board in its report of September, 1926, that the prevention of the waste of gas incident to the pro-duction of oil is of paramount importance in the conserva-tion and economical production of oil, and the president of the Institute is requested to appoint a committee of seven to devise and suggest to this board, or the executive com-mittee, such measures as will enable the industry, while continuing to meet the consumption requirements for pe-troleum and its products, to conserve in its natural state such reserves of petroleum as may not then be required for consumption. RESOLVED, That the president of the Institute appoint a committee of seven to formulate and recommend to this board or its executive committee, at the earliest practicable date, a program of legislation; Federal and State, to be advocated by the Institute giving sanction and effect to agreements by oil producers for the curtailment of produc-tion in pools where and during periods when there is over-production, having for their purpose the economical and orderly production of oil.

Jan 1, 1927

By Ray W. Carpenter, Ralph Hultgren, Raymond L. Orr

Heats of formation of Au-Zn alloys of compositions Au3Zn and AuZn were rneasured at several temperatures by liquid tin solution calorimetry. The data for Au3Zn show that much smaller heat and entropy effects are associated with the a2- a1 transformation than for the a1 - a transformation. This result is consistent with reported X-ray diffraction studies which indicate that the a1 and (a2 phases have ordered structures which only slightly differ, whereas the a phase is disordered. The heat of formation of AuZn(ß') does not change significantly between 322o and 8000 K, confirming that the ß' alloy remains highly ordered to high temperatures. Not many measurements have been made of the energies of order-disorder transformations in alloy phases. In many cases these energies may be conveniently determined by measuring heats of formation as a function of temperature. Many alloy phases approximately obey Kopp's law of additivity of heat capacities; as a consequence their heats of formation do not change with temperature. In ordered alloys, however, a decrease in degree of order with increasing temperature will contribute an endothermic component to the heat of formation. Thus, for ordered phases where other anomalous contributions to heat capacity in the alloy or its pure components are absent, a measured change in the heat of formation may be attributed to the energy of disordering. A portion of the Au-Zn phase diagram1" is shown in Fig. 1. The composition AuZn(ß') has a well-ordered superlattice structure of the CsCl type at room temperature. The alloy is considered to remain ordered to its melting point,1 although, from X-ray diffraction data and electromotive force measurements of zinc activities, Terpilowski3 concluded that considerable disordering began at -673°K. The Au3Zn composition is a disordered fee solid solution (a) at high temperatures. Between 693o and 543oK, the ailoy orders to form the a1 phase, having a structure based on the L12(AuCu3) type, but with a regular distribution of ordering faults in the c direction, making it tetragonal. Below 543oK, the alloy orders further by means of slight atomic shifts, without diffusion, yielding a complex long-period orthorhom-bic superlattice structure, a2.4-7 Heats of formation of Au3Zn(a2) and AuZn(ß') were measured at 363°K by Biltz et al.8 by aqueous solution calorimetry. Heat capacities of several alloys between 14.9 and 38.4 at. pet Zn in the range from 373" to 723°K were measured by Iwasaki ef al.6 Stoichiometric Au3Zn, however, was not included in the alloys measured, the nearest composition being 26.1 at, pet Zn. Also, the heating rate used for the measurements, 2 deg per min, may not have permitted equilibrium to be reached in the neighborhood of the transformations. Heat contents of solid and liquid AuZn were measured between 488o and 1138°K by Kubaschewski.9 It was decided to determine the ordering energies of Au3Zn and to check on the possible disordering of AuZn by measuring the heats of formation of these alloys at several temperatures. The present paper reports measurements by liquid tin solution calorimetry of the heats of formation of the three phases of Au3Zn at temperatures within their regions of stability, and of AuZn at a low (322°K) and a high (800°K) temperature. EXPERIMENTAL Alloy Preparation and X-Ray Examination. Ten-gram ingots of Au3Zn and AuZn were prepared by melting weighed amounts of gold (99.95 pct Au) and zinc (99.99 pet Zn) together in sealed evacuated Vycor tubes at 1060°K, followed by rapid quenching. The resulting ingots were homogenized at 900°K for 10 days. The Au3Zn alloy lost no weight in preparation, the loss from the AuZn alloy was enough to introduce an uncertainty of only 0.1 at. pet in its composition. Filings for X-ray examination were taken from various parts of each ingot and strain-annealed at 723°K for 20 min in vacuo. The Au3Zn filings were quenched rapidly to retain the disordered phase. Diffraction patterns were determined with an X-ray dif-fractometer using copper Ka radiation.

Jan 1, 1968

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting passed the following resolution : "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated;

Jan 1, 1934

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting. passed the following resolution: "The Board of Directors, having been appealed to by several Local . Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated:

Jan 1, 1937

By Arthur Notman

THE raw material men in all industries, and copper is no exception, are accustomed to think of them- selves as the whole show, and not without justice, for if there were no copper mines the world would have no copper. Nevertheless, many different things costing money and resulting in profits must be done to their product before it is ready for the world's use. In other words, they are making the frequent mistake of Chinking in terms of partial costs. Nobody really uses electrolytic copper. Possibly that is why nobody seems willing to pay anything for it. The manufacturers, being canny, do not buy any more electrolytic than they feel that they can work up and sell profitably, although they like to make the raw material men Chink that they will take all that can be produced. This is a state of affairs that has aroused my sympathy and curiosity, and has induced me to study the financial history of the copper wire and brass industry of the country or such portion of it as publishes any records readily available to the curious minded. About 60 per cent of the electrolytic copper used in this country is drawn into wire and consumed by the electrical industries. The remaining 40 per cent is

Jan 1, 1926

By M. L. Requa

EVERY forward step in civilization brings with it an increase in population and increasing demand for raw materials. Modern civilization, because of its industrial development, depends more and more for its well-being on ample supplies of raw materials; the higher the type of that civilization, the greater its dependence. No fact is more obvious than that the raw materials should be put to use with greatest prudence and efficiency. National life is not a matter of a decade or a century. Conservation is no longer a matter for political discussion; it is a vital element in the future welfare of all nations. Unfortunately, to the minds of many, conservation means the locking up of natural resources, their arbitrary withdrawal, bringing about, in short, a condition of industrial stagnation. This has occurred in past centuries through misdirected governmental effort. Two eminent engineers have variously defined conservation as follows:

Jan 1, 1925

By H. H. Johnson, Eric W. Johnson

A newly developed ac technique was used to measure the electrical-resistivity changes associated with both cyclic stressing and subsequent annealing of high-purity and OFHC copper. The early stage of push-pull fatigue was explored at 293° and 4.2°K, with stresses chosen for an expected fatigue life of 2 to 8 X 105 cycles. For high-purity copper, fatigue at 293°K was accompanied by an initial increase in resistivity. After about 5000 stress cycles, no further increase was observed. Annealing studies showed that the resisticity increment could be accounted for solely in terms of an increased dislocation density, to about 2 x 1010 disl pev sq cm. Fov 42°K fatigue, however, the resistivity increased continually, with no evidence of saturation, as approximately (No. of stress cycles)1/4. This is intevpreted to result from both dislocation multiplication and vacancy production; estimated vacancy concentrations are 10-4 to 10-9. The continuous resistivity increase was inhibited by interspersed annealing treatments at 293°K, which also raised the level of the stress-strain curve. These effects are attributed to annealing of vacancies into dislocation loops. In contrast, OFHC copper fatigued at 4.2°K showed saturation of electrical vesistivity after only a few hundred cycles, and it appeared that vacancies annealed out completely between 77° and 293°K. MaNY observations suggest that both dislocation multiplication and point-defect production are important aspects of fatigue deformation. An increase in dislocation density with number of stress cycles has been demonstrated or implied by several experimental techniques, including optical metallography with lithium fluoride,' electron microscopy with copper,2 thermal conductivity of Cu-Zn alloys,3 and peak-stress measurements during cycling at constant plastic strain amplitude.4,5 At low amplitudes and/or stresses saturation of fatigue hardening and dislocation density occurs early in the expected fatigue life,4-6 frequently by a few hundred cycles. The evidence for point-defect production is somewhat less extensive, but it is nonetheless persuasive. Rosenberg7 reported briefly that, for equal stresses, copper fatigued at liquid-hydrogen temperature displays an increase in electrical resistance some ten times that which accompanies unidirectional stressing. Further, the extra resistance saturates after a few hundred stress cycles, and does not anneal significantly until a temperature of about 170°K is attained.' Point-defect production during fatigue is also suggested by 1) the softening during cyclic stressing of initially strain-hardened polycrystal-line copper9, 2) the strong temperature dependence of the yield strength of fatigue-hardened mono- and polycrystalline copper,579"0 and 3) the influence of intermediate annealing upon slip-band formation in copper fatigued at 90°K.8 It is evident that characterization of the fatigued state requires a knowledge of both point-defect and dislocation densities. For this purpose electrical-resistivity measurements are useful, but they are difficult to perform because of geometric limitations. Push-pull fatigue is necessary to obtain a macroscopic ally uniform deformation over the specimen cross section; however, the specimen must then have a low slenderness ratio to avoid plastic buckling, while the standard dc resistivity technique requires a very slender specimen for

Jan 1, 1965

By Akinobu Kasami, Keiji Maeda, Makoto Naito, Masaharu Toyama

Gap electroluminescent diodes have been prepared by the vapor phase diffusion of zinc into n-Gap crystals which were grown from a gallium solution (10 wt pct Gap) doped with tellurium and Ga203. A marked improvement in the efficiency of the red electrolumines -cence has been achieved by heat treatment after diffusion. External quantum efficiencies of diodes annealed under optimum conditions are 0.2 to 0.6 pct at room temperature, or about 200 times higher than the efficiencies of diodes quenched after diffusion. The optimum dopant concentrations in the gallium melt from which the crystals were grown are 3to6 x at. pct Te and 4 to 8 x 10-2 mol pct Ga203. The efficient diodes are characterized by linearly graded junctions with an i-layer 0.1 to 0.2u thick. Annealing increases the emission intensity by a factor of 20 to 50 and decreases the current density to 1/3 to 1/8 that of quenched diodes at a given bias. The decrease in current is attributed to an annihilation of deep recombination centers in the depletion layer. The increase in emission intensity is interpreted in terms of an increase in lifetime of minority carriers and an increase in the relative intensity of red-to-infrared emission. The dependence of these quantities on the tellurium and oxygen doping levels is also discussed. A number of studies have been made of the red light emission from for ward-biased Gap diodes.' At room temperature this emission band is centered at 7OOO? with a spectral width of nearly 1000?. Low-tempera-ture photoluminescence indicates that this emission is due to either the radiative annihilation of an exciton bound to a pair of zinc and oxygen atoms substituting on nearest neighbor lattice sites2,3 or the radiative recombination of an electron bound to this Zn-O pair with a hole bound to an isolated zinc shallow acceptor.3 An emission band is also observed with a spectral peak at 9800?. This infrared emission has been shown to be due to the recombination of an electron trapped at an isolated oxygen deep donor with a hole trapped at an isolated zinc acceptor.4 The red emission from Gap diodes is fairly efficient at room temperature because the nearest neighbor Zn-0 pair forms a deep electron trap at 0.3 to 0.4 ev below the edge of the conduction band.2'4 In diodes grown by liquid epitaxy an external quantum efficiency of 2.1 x 10-2 (photon/electron) has been attained by heat treatment at relatively low temperatures.5 This heat treatment was found to increase the efficiency by a factor of 3 to 6. However, no detailed studies have-been reported on the effects of heat treatment. We can only cite Onton and Lorenz's work6 on the change ; in the relative intensity of red-to-infrared emission. Heat treatment has also been tried on junctions built in during growth, but contrary to expectations the efficiency decreased. In-diffusion is a simple and controllable method of fabricating p-n junctions. For Gap, zinc is generally used to form a p-type layer on n-type crystals. The emission efficiencies of in-diffused diodes are, however, extremely low in comparison with liquid epitaxial diodes.' Although efficiencies as high as 2 x 1O-3 have been reported, values from 10-6 to 10-4 are generally obtained by typical diffusion techniques. Out-diffused diodes are known to be a little more efficient than in-diffused diodes. Nevertheless, the quantum efficiency is at most 7 x 10- 3 and ordinarily of the order of 10-4.8 NO results have been reported on heat treatment of either in-diffused or out-diffused diodes. This paper reports a marked improvement in the efficiency of the red emission observed for in-dif-fused diodes as a result of heat treatment after diffusion. The method described reproducibly yields diodes with external quantum efficiencies of 2 to 6 x 10-3. The observed dependence of efficiency on annealing time and on doping level will be discussed in terms of the lifetime of minority carriers and the formation of Zn-O complex pairs. EXPERIMENTAL A) Diode Fabrication. The n-Gap crystals used in this study were grown from a saturated gallium solution by a slow cooling method.8 The Gap content in the gallium melt was fixed to 10 wt pct corresponding to a growth temperature of about 1100 Tellurium was chosen as the n-type dopant and added to the melt in concentrations ranging from 0.001 to 0.06 at. pct. Oxygen was added in the form of Ga2O3, whose concentration was varied from 0.004 to 0.2 mol pct. The resulting crystals were platelets with well-developed (111) surfaces. Typical electrical properties were Hall mobilities of 130 to 30 sq cm per v-sec and carrier concentrations of 1016 to 10" cm-3 at room temperature. Diodes prepared from crystals with relatively low doping levels, in which u = 130 to 100 sq cm per v-sec and n = 0.6 to 6 x 1017 Cm-3, were examined in detail. The p-n junctions were produced in these n-Gap crystals by the diffusion of zinc from the vapor phase by the following procedure. The platelets were carefully lapped on both sides to a thickness of 150 to 200 u while maintaining the (111) orientation. After being etched in hot aqua regia, the crystals together with the zinc were sealed in an evacuated 12 mm ID quartz ampoule 20 cm long. The crystals and the zinc were then separated from each other at opposite ends

Jan 1, 1970

NEVADA SECTION J. W. HUTCHINSON, Chairman, FRANCIS CHURCH LINCOLN, Vice-Chairman, HENRY M. RIVES, Secretary-Treasurer, Reno, Nevada W. H. BLACKBURN, E. A. JULIAN, EMMET D. BOYLE, JOHN G. KIRCHEN, FREDERICK BRADSHAW, C. B. LAKENAN, TASKER L. ODDIE. The formation of the Nevada Section was originally suggested by Professor F. C. Lincoln, who had discussed the subject with Mr. William L. Saunders when the latter was President of the Institute. Professor Lincoln sought the assistance of the Nevada Mine Operators' Association, whose Executive Committee constituted itself a Committee on Organization, and authority for the establishment of a Nevada Section to include the entire State was secured from the Board of Directors of the Institute. The formal installation took place at 10 A.M. on May 18, Mr. William L. Saunders officiating. The Honorable Emmet D.. Boyle, Governor of Nevada (and a member of the Nevada Section), made the address of welcome. On the afternoon of the same day, a technical session was held, at which the following papers were presented: History and Development of the Cyanide Process Charles Butters Virginia City Whitman Symmes Ore Deposition at Steamboat Springs Prof. J. C. Jones

Jan 7, 1916

By James M. Barker

Sulfur is a nonmetallic element of great physical and economic importance to the world. It is widely but sparingly distributed throughout the hydrosphere, lithosphere, and biosphere. Sulfur is the tenth most abundant element in the universe and eighth most abundant in the sun. In the earth's crust, which is mainly igneous, it ranks 14th, but is eighth or ninth in sediments (Kaplan, 1972; Stanton, 1972). It apparently is very abundant in the core of the earth, because it is a strong chalcophile, and it is fifth in abundance in stony and iron meteorites (Field, 1972) where it occurs as trolite (FeS). In ancient times sulfur was called brimstone, literally "burning stone." Today the term brimstone is used interchangeably with the term elemental sulfur. Shelton (1979) summarized most of the common definitions of terms, grades, and specifications for the sulfur industry as follows (with minor additions): Sources of Sulfur: Combined sulfur-Sulfur that occurs in nature combined with other elements. Cupriferous pyrites-Pyrite containing relatively minor amounts of copper sulfide minerals. Hydrogen sulfide-A toxic gas (H2S) occurring in natural gas and petroleum. Involuntary sulfur-Sulfur produced primarily as a result of legislative or process mandates. Native sulfur-Sulfur that occurs in nature in the elemental (uncombined) form. Nonferrous metal sulfides-Copper, lead, zinc, nickel, and molybdenum sulfides that are processed for their metal content. Organic sulfurs-Complex organic sulfur compounds occurring in petroleum, coal, oil shale, and tar sands. Pyrites-Iron sulfide minerals that include pyrite, marcasite, and pyrrhotite. Sulfate sulfurs-Sulfur in anhydrite and gypsum. Voluntary sulfur-Sulfur produced in response to market forces. Basic Sulfur Products Produced and Marketed: Acid sludge-Contaminated sulfuric acid usually returned to acid plants for reconstitution. Brimstone-Synonymous with crude sulfur. Bright sulfur-Crude sulfur free of discoloring impurities and bright yellow in color. Broken sulfur-Solid crude sulfur crushed to -8 in. Byproduct sulfuric acid--Sulfuric acid produced as a byproduct of a metallurgical or industrial process, generally relating to combined sulfur sources. Crude sulfur-Commercial nomenclature for elemental sulfur. Dark sulfur-Crude sulfur discolored by minor quantities of hydrocarbons ranging up to 0.3 % carbon content. Elemental sulfur-Processed sulfur in the elemental form produced from native sulfur or combined sulfur sources, generally with a minimum sulfur content of 99.5%. Formed sulfur-Elemental sulfur cast or pressed into particular shapes to enhance handling and to suppress dust generation and moisture retention. Frasch sulfur-Elemental sulfur produced from native sulfur sources by the Frasch mining process. Hydrogen sulfide-Associated with natural gas or petroleum and produced at refineries and coke oven plants; used to make sulfuric acid or recovered sulfur. Liquid sulfur-Synonymous with molten sulfur. Liquid sulfur dioxide-Purified sulfur dioxide compressed to the liquid phase. Molten sulfur-Crude sulfur in the molten phase.

Jan 1, 1983

By C. A. Hansen

The furnace used for experimental work is shown in Fig. 1. One fireclay sagger, or pot, was set within another and the space between the two filled with Silox heat insulation. The hearth is a cast-iron plate with an imbedded ribbon of nichrome wire; this wire heater is connected to a potential regulator, which permits a very close voltage control. A mechanically driven arm is fitted with rabble blades so arranged that a uniformly thick ore bed may be maintained indefinitely. This arm is usually driven at about one revolution per minute but its speed of rotation can be varied as desired. Compressed air is led into the furnace through a meter, and it was found necessary to preheat the air in order to secure the definitely isothermal conditions sought. With this arrangement, it is possible to maintain any desired temperature constant within about 5" C. for any desired length of time and to

Jan 1, 1921

By Donald A. Brobst

The minerals barite (BaSO4-barium sulfate) and witherite (BaCO3-barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1980 consumed at least 90% of the world's production of 8.8 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The remaining 10% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity filling, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favorable for the discovery of new deposits of commercial value. Witherite is much less common and abundant than barite, although it is more desirable in many ways as a raw material for the production of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir conditions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemically, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite homogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber industry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and linoleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other substances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weigh down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1983

By Frances Hurd

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200' C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating.

Jan 1, 1927

By Charles M. Rolker

The Mariposa estate, a grant made by the Mexican Government to Juan 13. Alvarado, during the time when California was still under the dominion of Mexico, was purchased in 1847 by J. C. Fremont, and the United States patent issued to him in 1856. By sale, or its equivalent, money advanced, the property came into the hands of the Mariposa Company, June 25th, 1863, and through a varied existence of work and temporary inactivity, has as yet been kept as an undivided property, and rests at present with the Mariposa Land and Mining Company of California. I pass over this period of 15 years without giving the history of the ups and downs of the estate, partly because it is familiar to many, and also because I think in such a case this paper would assume too much the character of a narrative. The estate is situated in Mariposa County, California, about 170 miles southeast of San Francisco. It begins in lat. 37' 26' 38'' north, and long. 119' 55' west, and runs 6 miles north; thence 69 miles west; thence 5 miles northwesterly towards the Merced River; thence 84 miles southerly; thence 3 miles easterly; thence 1 mile southerly; thence 2 miles easterly; thence 2 miles southerly; thence 2 miles easterly; thence 1 mile southerly; thence 2 miles easterly; thence 1 mile northerly, and thence 2 miles easterly to the place of the beginning; embracing 44,387 acres (70 sq. miles) more or less. To describe this vast estate in detail as to its full geology, its numerous quartz veins, its many facilities to exploit them and work them by cheap methods, would lead me further than I intend to go at present, and I will content myself to describe the latest workings of the company and its immediate field of operations. As long ago as 1860 the late Dr. Adelberg advised the running of an adit from the northwestern edge of the estate at Benton Mills 011 the Mereed River. His object was to undercut the deepest workings of the then paying mines on the estate—the Pine Tree and Josephine. Following this advice, the tunnel known as "River Tunnel " was commenced. Its entrance is in S. 5, T. 4, s. R. 17 E. It is run in

Jan 1, 1879

By R. B. Newcombe

Despite abnormal economic conditions and the unhealthy state of the petroleum industry, 1930 closed without any marked decline in total production of oil in the Middle Western States. The most accurate figures available would indicate for this district an output of close to 25,000,000 bbl. for 1930 as compared to 26,000,000 bbl. for 1929. This can be accounted for by the settled nature of a great many of the wells producing in this area and the favorable geographical position, which affords adequate refining and marketing facilities. The only new flush production field discovered in the area was the Legrande oil pool in southeastern Hart County in western Kentucky, where wells up to 1000 bbl. initial have been reported from a shallow depth. Important extensions have been found in a number of central Ohio fields, and activity in the central Michigan area resulted in new pools along the northwest trend of the Mt. Pleasant structure. These new districts, known as the Leaton and Vernon pools, have not yet reached the scope of the Mt. Pleasant field proper, and although the structure is similar, sand conditions are not strictly analogous. Wildcatting was retarded somewhat by the scarcity of market for oil and many important wells were shut down for several months. This has not shown such a profound effect on production as the reticence of operators to drill inside proven locations. The major companies have not been able to dispose of their oil and the smaller operating units are having trouble financing their projects. The result is that oil in sight is not being produced and output is suffering accordingly. Another important effect on production was the introduction of proration by the major crude purchasers and a voluntary shut-down by Kentucky operators. This step became necessary because of the glutting of lake port refineries with Mid-Continent oil, and was not fostered by regulating state bodies, as in the case of the southwestern states. Small refining units have sprung up to meet this situation in a number of instances but they have experienced some difficulty in disposing of their product because of "dumping" tactics from other quarters. New refinery outlets on the Great Lakes and new pipe line connections should tend to alleviate this difficulty during the coming year. The

Jan 1, 1931

By J. A. Goebel, S. Rosen

IN the NiAl phase diagram the NiAl (CsC1-type) phase field extends over a large composition range. At elevated temperatures the nickel-rich phase boundary extends to a composition of about 70 at. pct Ni, a value which is within 5 at. pct of the Ni3A1 (Cu 3 Au-type) phase boundary.' At room temperature, however, the maximum nickel content is only about 60 at. pct. Experiments have shown that alloys containing greater than 63 at. pct Ni when quenched from temperatures below 1000°C contain the equilibrium phases NiAl and Ni3A1. On the other hand, when these same alloys are quenched from temperatures above 1000°C and examined microscopically, a typically martensitic decomposition product appears in the microstructure as shown in the micrograph of Fig. 1. The structure of the martensitic phase has been determined by employing powder X-ray diffraction techniques to be an "ordered" AuCu type (Strukturbericht Llo, space group P/4 mmm - DL). The diffraction pattern of this phase differs from that of AuCu in the appearance of superlattice lines. The structure is shown in Fig. 2. The open circles represent nickel atoms and the half-shaded circles represent nickel and aluminum atoms which are randomly distributed. The sites represented by half-shaded circles would be occupied solely by nickel atoms at a stoichiometry of Ni3A1. The alloys used in this investigation were prepared from 99.99 wt pct Al and 99.99 wt pct Ni by arc melting charges of varying compositions in a water-cooled copper hearth using a tungsten electrode in a gettered argon atmosphere. In all cases chemical analysis agreed within $ at. pct with the nominal compositions of the alloys. Annealing treatments were carried out in a vertical resistance furnace through which a stream of argon gas was flowing. Specimens, which were wrapped in tantalum foil, were quenched by allowing the specimens to drop into a bucket containing iced brine. X-ray diffraction patterns were obtained from -325 mesh powder specimens by using a 114.8-mm

Jan 1, 1969

By Robert B Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By Robert B. Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By B. Chalmers, S. Wojciechowski

THE structure of the equiaxed zone of several A1-Cu samples mechanically stirred during unidirectional solidification was examined. The stirring was produced by rotary oscillation of the mold about its vertical axis.' It was found that in Some samples the structure is not of the same type over the whole of the equiaxed zone; it consists of regions with two different etching responses. Fig. 1 shows this structure in a Al-1 wt pct ku sample. The lighter etching regions with a coarse structure form something like a network and the darker etching regions with a finer structure can be observed as the continuation of the coarse structure inside this network. The difference in size and shape of the dendrite branches (they are rounded in the coarser structure) is similar to that found by Williamson and Chalmers in ice crystals solidified in undercooled water: when the amount of undercooling was small, the ice crystals were more rounded and coarser than these solidified with a larger amount of undercooling.' It seems justified to conclude that the observed structure resulted from solidification under different thermal conditions: the coarser structure solidified first out of the "purer" liquid and with a smaller amount of undercooling and the finer was formed later out of solute-enriched liquid under conditions of much more rapid heat extraction. A considerable change in the heat flow conditions at the later stages of solidification can be easily understood by taking into account that the coarser crystals form a continuous network and the amount of trapped liquid is relatively small; hence the contribution of latent heat is much smaller in the later stages of solidification. The difference in structure and etching characteristic reflects a difference in composition between these two regions. It was found that the darker etching re- gions are harder (30.4 to 31.3 HV5) than the lighter etching ones (25 to 26 HV5). A similar type of structure was found in a A1-4 wt pct Cu sample grown by Czochralski method. Fig. 2 shows the structure in the lower part of a sample grown slowly and then decanted by a rapid removing of the sample from the melt. In a few places trapped liquid solidified in the same manner as in the sample shown in Fig. 1.

Jan 1, 1968