Search Documents

By Francisco Morganti

This report gives in the first part the metallurgical basics for the production of AHSS grades in integrated steel plants starting at the melt shop and ending at the annealing lines of the cold mill. The corresponding process and plant technologies in each production step with its specifics and rules are explained. In the second part by way of example the practical requirements for TRIP 780 steel grade are highlighted like a recipe for process control in the steel plant, hot and cold rolling mill, annealing line and finally skin pass mill. Measuring of mechanical technological properties on samples shows that the specifications according to DIN EN 10268 are fulfilled.

Oct 30, 2017

By Jefferson Lisboa Lelis, Marcos Roberto Soares da Silva, Maiara Rodrigues Gouveia

Nowadays, due the development of new hot rolled strips at USIMINAS, established the necessity of realizing studies to define new parameters for the welding machine of new pickling line, in order to improve mechanical and metallurgical properties of these materials. The aim of this study was to evaluate the weldability of high strength low-alloy steel with low boron content with tensile strength above 600MPa.The influence of energy input and preheating temperature on the mechanical properties of hot rolled strips were analyzed at three distinct thickness (2, 4 and 6 mm). To perform these evaluations were used tensile test, micro-hardness, metallography (micro and macro examination) and scanning electron microscopy analysis. In resume, a good welding performance was achieved, increasing preheating temperature and the welding energy higher than 60%.

Oct 13, 2019

By Andreas Cestonaro

Roll grade evolution in plate mill applications is traditionally following the development in hot strip mills. New grades normally find their way into service only after being successfully implemented in hot strip production. The majority of the plate mills worldwide are using work roll grades that have been invented before the 1980’s. But today the demands in the mills are pushed by sophisticated product mixes and longer rolling campaigns. The result of this development is a higher wear rate on the work rolls and as a consequence roll hardness is increased and advanced roll materials are used. The backup rolls are also affected by this. The wear rate is higher and the mechanical impact in terms of contact pressure and work hardening is increasing. This paper outlines the results of the roll grade development at Gontermann-Peipers and introduces new materials for work and backup rolls for plate mills.

Jul 30, 2018

By Thomas Höfler, Michael Auinger, Bernhard Linder

Gas-fired pusher furnaces are commonly used to heat steel slabs before hot rolling. Temperatures well above 1000 °C combined with an oxidizing atmosphere containing H2O, CO2 and O2 result in rapid oxidation of most steel grades. The resulting oxide scale and the chemistry of the metal-scale-interface are major determining factors for the occurrence of hot rolling defects. To better understand these phenomena, lab-scale trials were performed with two different steel grades in an electric tube furnace in the temperature range 1000-1250 °C, using an atmosphere of about 20 % H2O, 7 % CO2 and 3 % O2. Humidification of the gas was achieved by evaporation, using a custom thermostat with standard laboratory glassware. The resulting samples were prepared metallographically, using cold mounting under vacuum with taper section angles, and analyzed using light microscopy and SEM/EDS. The scale structure of the Si alloyed steel was highly dependent on the oxidation temperature due to the formation of eutectic liquid phases of FeO, Fe2SiO4 and FeAl2O4. Below the eutectic temperature, the scale of the Si steel appeared to be made up of three distinct areas: The external scale consisting solely of Fe oxides, the internal scale containing Fe2SiO4 and FeAl2O4, and an internal oxidation zone with SiO2 and Al2O3 in a mostly plain Fe matrix. Comparisons of the experimental results with simulations of the internal oxidation showed good qualitative agreement.

Oct 1, 2019

By Daniel Hajduk

Efficiency of back up rolls depends mostly on two parameters – length of campaign and dressing amount after the campaign. The longer the campaign (in terms of rolled tones) is, the higher the dressing amount. To solve this task properly it is necessary to know the distribution of accumulated damage in the working layer of the roll caused by previous campaigns and by loads (separating force and bending) during present campaign respecting changing conditions of material properties (hardness) through radius of the roll. To find an optimum dressing amount an algorithm has been developed and specialized computer program will be presented, that takes real measured loads during the backup roll campaign, calculates fatigue damage in the roll and suggests relevant dressing amount. This can help to prolong service life of rolls, minimize the risk of spalls and reach maximum efficiency in terms of rolled tones/km per roll.

Jul 30, 2018

By Francisco Morganti

Weight reduction is the main target of all carmakers, which results in a continuous development of new steel grades. Latest 3rdgeneration advanced high-strength steel grades (AHSS) are complex materials with special chemical compositions and multiphase microstructures. The pickling, annealing and galvanizing processes of these grades aresomewhatdifferent due to the changed chemical compositions and microstructures. Therefore, these innovative steel grades place new demands on the plant technology of pickling, annealing and galvanizing lines. The most significant challenges for the pickling process are sludge occurrence during pickling, varying pickling times, weld ability of the materials, changed visual appearance and required high surface qualities. The most important topic concerning annealing line is a precisely controlled and very flexible heating and cooling process in the furnace.One of the new requirements in galvanizing linesis the prevention of surface faults caused by bare spots, which can occur since these materials feature a higher content of alloying elements like silicon or manganese. Prevention is possible with the special pre-oxidation technologies.Due to the higher strength of the material also the mechanical equipment has to be designed differently in these lines. This paper describes the influences of the changed chemical composition and material characteristics of modern steel grades on the pickling, annealing and galvanizing process and gives an overview about the technical solutions.

Oct 30, 2017

By Jean François Stumper

This paper presents the TMT “3D TopScan” profilemeter, which is a Radar-based profilemeter that measures the total burden surface within a few seconds and on a continuous basis. This equipment is based on an electronically steered solid-state radar scanner, such that a very large amount of surface data is collected within short time intervals. These new electronically steered antenna systems are the key to meet the demands for both accuracy and speed. The TMT probe is installed at a fixed location at the top cone, such that it does not interfere with the charging, enabling a continuous measurement and a compact design.Blast furnace charging optimization can be achieved based on its measurement data. The burden surface is continuously measured every few seconds, enabling the blast furnace operator to detect any details including asymmetries or irregularities in the surface pattern. A variety of process analysis tools are available. Due to the continuous and fast measurement, the burden descent speed can be supervised without process interruption on an ongoing basis. More accurate process models (layer models) than ever are obtained which fully consider the unsymmetries.This technology, developed by TMT Tapping Measuring Technology, is successfully in operation at Salzgitter Flachstahl GmbH at their blast furnace B. The probe and the data evaluation tools combine today’s technological capabilities in measurement technology with the practical requirements of blast furnace operation.

Aug 16, 2017

By Peter Fajfa, Heinz Palkowski, Jakob Kraner, Matjaž Godec

The study of asymmetric rolling on the AA 5454 aluminium alloy plates was carried out. The plates were taken directly from the industrial hot rolled sheet. They were cold rolled on the laboratory mill with different rotation speed of the upper and the lower work roller with the strains around 33 % and 44 %. To get closer to the industrial conditions the maximal dimensions of the rolled plates for laboratory rolling mill and the special industrial lubricant were used. After deformation the plates were annealed to the soft condition. This research was focused on all possible effects of asymmetric rolling: The reduction of rolling force, the increase of strain at same set roll gap, bending of workpiece, finer microstructure, more heterogeneous textures and as a consequence of that better mechanical properties. The asymmetric rolling with favourable mechanisms in the deformation zone has created the material with the homogeneous hardness in the cross section and with lower anisotropy, which is crucial for improvement of formability properties of aluminium work hardened alloys and to get closer to properties of steels. In the presented paper the general impact and different effects of speed difference of rollers was investigated on cold rolled aluminium alloy. Obtained and analysed results explain the function of asymmetry in rolling process and the options to implement the asymmetric rolling in industrial plant.

Oct 1, 2019

By Bruno Kneipel Neto, Mylena Inaiê Correia, Fabricio Cerqueira, José Francisco da Silva Filho

The automotive industry, when aiming to increase the resistance to corrosion, uses in the Body in White (BIW) concept the galvanized steels. The hot-dip galvanized steels that stand out most are known as GI steels. They are formed by the zinc element and by phases of intermetallic intermediate iron-aluminum-zinc compounds. The characteristic properties of the GI coating are directly related to the formation of the intermetallic layer, which is responsible for providing the connection between the metal substrate and the coating layer. In this context, two different types of steel (SAE1005 and TRIP780 steel) were used for laboratory characterization of their intermetallic layers through metallographic techniques. The results of the tests showed that the inclined section metallographic inlay technique allows obtaining a larger region of analysis of the intermetallic layer. For the surface analysis, it was observed that the chemical solution used in the preparation of the samples was effective, making possible an analysis more specific about the intermetallic layer formation, distribution and morphology.

Oct 12, 2019

By Marcel Antonio Arcari Bassani

In the mining industry, it is common to have data collected in various formats. In an open pit mining operation, at the early stages of exploration samples are obtained from diamond drillholes. During the production stage, samples are collected from blastholes. The last is more numerous but less precise. From a geostatistical view, this dissimilarity has to be considered to integrate the two sources of information. To combine this different data, three methodologies were investigated: simple kriging with local varying mean, cokriging and ordinary kriging. The exhaustive Walker Lake data set was used and it is considered the source to obtain the true grades. Initially, samples were obtained from the exhaustive data set at a regular spacing grid of 20 x 20 meters. Next, samples were obtained again from the exhaustive dataset at a regular spacing of 5 x 5 meters and a relative error of 25% was added. Then, both data were used to estimate blocks using the three methods mentioned. The grade tonnage curves were compared with the true block grade distribution. Moreover, the block misclassification was evaluated. The results showed that ordinary kriging produced estimates closer to the true block grade distribution and reduced the block misclassification.

Aug 8, 2018

By William Sergio Flores Roman

Los aceros para armaduras de hormigón tienen que exhibir una buena relación entre resistencia y tenacidad que se ve reflejado en la performance del producto en servicio al ser aplicado a esfuerzos exigidos. Acerbrag es una empresa que produce aceros para la industria de la construcción teniendo en su gama los aceros de medio carbono para la fabricación de barras conformadas de dureza natural para armaduras en estructuras de hormigón. El objetivo de este trabajo es encontrar criterios de ventanas de trabajos operacionales y de control para la manufactura de aceros con buenas propiedades mecánicas en términos de resistencia y tenacidad. Este paper muestra los resultados de los trabajos realizados en las diferentes áreas productivas para conseguir un producto final con mayor resistencia a altas exigencias en servicio, además, reporta diferentes aspectos del proceso de manufactura del producto que van desde el ajuste de la composición química del acero, incluyendo criterios de propiedades mecánicas objetivos, criterios de calidad interna mostrando la microestructura de la barra antes y después de los cambios y finalmente la calidad dimensional y superficial de la barra nervurada, este último potenciando la falla prematura del material. Todos estos cambios, se ven reflejados finalmente en la performance de la barra, sometida a los nuevos criterios de exigencia en los ensayos mecánicos.

Oct 30, 2017

By Rafael Abreu Fraga, Carlos Noberto Paula da Silva, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Since 2016 Gerdau Ouro Branco has been producing steel plates of various qualities and grades. However, it was not until 2018 that the first plates produced by accelerated cooling process were made available for external testing, in this case for large diameter UOE pipes manufacturing. Recent line pipe and OCTG specifications are showing that the oil and gas market still consumes regular API grades, such as X60, X65 and X70, however with increasing wall thicknesses, reaching values up to 1.5 inches. These specifications also demand longitudinal and transverse tensile guarantees and drop weight tear tests in temperatures as low as -40°C. Projects with these types of mechanical properties present process requirements as challenging as those necessary for higher API grades in lower thicknesses. This paper shows the steel design concepts and rolling routes for achieving the necessary properties for X70 steel plates in 28.15 mm. The microstructural features were also investigated and associated with the production process and the tensile and toughness results. Finally, challenges such as tensile anisotropy and DWTT abnormal fracture are presented.

Oct 1, 2019

By Boryong Lee, Heedong Sung, Minho Park, Sunyoung Choi

Recently, the demand for ultra-thin steel plate with high hardness and strength has been increasing in various industries. In order to satisfy this requirement, steel company designs the chemistry with low CEQ and obtains the required characteristics through quenching and tempering process. Especially, these steels are accompanied by low temperature tempering as a necessary process. Unlike ordinary high temperature tempering steels, it is impossible to improve the flatness after low temperature tempering. Therefore, shape control in the quenching process is very important for securing the excellent quality flatness. In order to obtain flatness in the quenching process, uniform cooling inside the plate should be accompanied. However, the quenching process has limitations in estimating the temperature behavior during cooling because the plate temperature is lowered to room temperature. In this study, a thermocouple was installed inside the actual quenching plate to measure the temperature behavior during cooling and to establish the manufacturing conditions of the quenching plate to ensure excellent flatness quality.

Oct 1, 2019

By Patrick Edward Connell

The next generation of the well-established 3-roll Reducing & Sizing Block (RSB), the RSB SCS® is the latest milestone in reducing and sizing technology for SBQ products. It offers enhanced bar quality, improved productivity, mill availability and economy as well as a simplified, safe and environmentally friendly operation. A newly developed modular drive concept of the RSB SCS® grants a smaller footprint in the layout, a reduced oil-lubrication volume and a simplified maintenance schedule. Intelligent engineering leads furthermore to reduced hydraulic functions of the RSB SCS®, which ensures a safe and environmentally friendly rolling. Another integral part of the RSB SCS® is an innovative stand changing concept, which allows automatic stand changing within three minutes. The new RSB SCS® also includes a Fast Remote Control (FRC) which enables the immediate adjustment of the roll gap against the rolling force (under load) within milliseconds. Size changes along the free-size range can also be made within the traditional billet gaps in less than five seconds. At the core of the future-oriented RSB SCS® is a real-time closed-loop control system called Size Control System (SCS®) acting with 3-roll stands adjustable under load (AUL) and / or the heavy duty stands. These features remarkably further improve the rolled tolerances and their reproducibility, and at the same time simplify the operation by means of an automated optimization of the process parameters for the rolled bars.

Aug 16, 2017

By Jorge Madias

Durante la laminación de barras y alambrones para construcción civil; perfiles y ángulos estructurales y barras redondas y hexagonales de aceros de corte libre puede presentarse la apertura de la punta o la cola y el estallido central, con la consiguiente parada y caída de la productividad, y pérdida de rendimiento metálico. En este trabajo se analizan las diversas causas que confluyen para que este problema ocurra. Se analiza la influencia de posibles defectos en las palanquillas, las características del corte de las mismas y otros problemas de calidad. Se revisa el rol del precalentamiento previo a la laminación, la refrigeración de los cilindros, el diseño de pasadas y la respuesta del material en función de su ductilidad. Se presentan diversos casos industriales para ilustrar las diferentes razones detrás del problema de la apertura de punta.

Jul 30, 2018

By Christian Overhagen

In bar and wire rod mills, rolling procedures featuring three- and four-roll technologies are state-of-the-art to produce high-quality long products. While a rolling model for the three-roll process including an equivalent pass method was already presented by the author, pass design methods are dealt with in the current work. The geometry of the rolled product and roll grooves are described mathematically using functional contours, allowing geometric-numerical methods to be used for manipulation and deformation simulation of the rolled product. For a given pass, the output section is constructed using these methods. Roll force, torque and rolling power are calculated using the mathematical rolling model presented before. Interstand tensions are discussed as influencing parameters on the force, torque and power demands, as well as on the section shape. A mathematical model for the influence of interstand tensions on lateral spread is incorporated in the model. To complete the pass design model, elastic mill stand feedback is considered in terms of a fixed elastic modulus for each rolling stand, the elastic feedback and therefore cross-sectional variation due to elastic mill spring being calculated iteratively from the roll force by application of the Gagemeter equation. The interaction of section height and width faults due to elastic mill spring and spread variations is analyzed in detail and the consequences for the roll pass design are shown.

Oct 1, 2019

By Danilo Gonçalves de Oliveira, Rogério Martins Pereira

Chatter is a widely studied vibration phenomenon that affects most cold mills around the world and its impact on these lines are tremendous: from productivity and quality losses to mechanical equipment damage. The investigation of its origins and how to minimize the occurrences and their impact on the equipment require special instrumentation and algorithms in order to have a detection of the vibrations as soon as they start. This paper presents three methods of identification of chatter on a Tandem Cold Mill and the actions to leave the vibration frequency range before its amplitude achieve catastrophic values.

Oct 1, 2019

By Bruno Alves Resende, Antonio Adel dos Santos

Temperature, microstructure and dimensions are the main material parameters to be controlled during hot rolling of steel. Although thermal mathematical models have long been developed and applied for hot strip rolling, each Hot Strip Mill (HSM) must have its own model adapted to its facilities. Thus, a mathematical model for temperature evolution during rough rolling has been developed for the Usiminas HSM at Ipatinga Plant. The model achieved a high level of accuracy, which was assessed by comparing measured values of temperature at the hot strip mill entry with the calculated ones, the difference ranging from 9°C to 17°C. Application examples have shown that the slab can be occasionally stopped before start of rolling for as long as a couple of minutes without compromising its further processing. On the other hand, if the transfer bar stops after rough rolling even for short time, further processing in the HSM can be hindered, due to excessive temperature drop. In case of such abnormal line stop, the model can be used as a tool for decision-making to either continuing the planned rolling schedule or to changing the route, thus improving the overall rolling process.

Oct 1, 2019

By Jari Larkiola, Aarne Pohjonen, Juha Jokisaari, Oskari Seppälä, Joonas Ilmola

Finite element method (FEM) is widely used to model the hot strip rolling process. Flatness defects e.g. front-end bending in multipass hot strip rolling is studied by authors using a finite element (FE) model with interactively operating automated controlling logic (ACL) [1]. However, industrial corresponding grade of accuracy in strip thickness subsequent to the rolling pass is not easily accessible in FE-model without separate calculation of significant rolling parameters and integrated roll gap control. In order to study flatness defects and optimize pass schedules the controlling and physics of the FE-model must correspond to the industrial process. For this need the automated controlling logic is upgraded by setup calculations to predicting roll force and work roll flattening. These predictions are utilized in setup positioning of a work rolls. Reliable setup calculation enables smooth multi stand rolling process without significant additional adjustment of roll gap clearance. State of art rolling technology requires above-mentioned setup controlling for the FE simulations to simulate different pass schedules without time consuming preparations. Operational setup calculations together with automated controlling logic of hot strip rolling enable simulation of new pass schedules and efficient problem solving.

Oct 1, 2019

By Gabriel Oliveira Glória

In the context of changing culture, the society is increasingly looking for environmentally friendly materials, the natural fibers appear as an option to substitute the synthetic. Among these natural fibers, the PALF fiber may be considered an option, but there is limited information about the flexural strength of epoxy composites incorporated with PALF fibers. Therefore, the objective of this work was to investigate the mechanical properties in bending tests of epoxy composites incorporated with up to 30% in volume of PALF fibers. The results showed that the PALF fiber increase the flexural strength of polymer composites.

Aug 16, 2017